Raspberry pi 0 w as Repeater

jaylthegreat · May 28, 2020, 2:54pm

Hello all,

So I've been trying to configure a raspberry pi 0 as a repeater. I'm currently using factory image 18.06.1 (although I have had the same problems with 19.07.2 and a snapshot). Also I'm a programmer mostly and am new to all of this networking stuff, so please excuse any poor terminology.

The problem is that when I add the second connection, (usually I will connect it as client to router and then create the access point) neither will work. upon reboot i find that a new wifi interface, wlan0-1, is created. This makes sense; however, ifconfig reveals that this is the only one that currently gets an IP.

If I manually shut it down with ip link set wlan0-1 down it does as expected and usually wlan0 will immediately connect to my router. I found that no combination of turning them off and on would fix it.

I did manage to manually get both networks to work at the same time, but it's messy and there must be a better way. I will detail the process below and then share my config files at the end.

shutdown wlan0-1, flush ip (not certain what this does, got it from guide), turn on, set ip

ip set link wlan0-1 down
ip addr flush dev wlan0-1
ip set link wlan0-1 up
ip addr add 10.0.0.1/24 dev wlan0-1

start access point with hostapd. note that I had to use wpad hostapd, if i just used hostapd i would have the same issue where it would turn off the client.

Interestingly, when i do this ifconfig doesnt show wlan0-1 at all and ip addr shows it as down.

wpad hostapd -i wlan0-1 /etc/hostapd.conf

hostapd.conf

interface=wlan0-1
driver=nl80211
ssid=TryVictoryNet
channel=6

/etc/config/network

config interface 'loopback'
        option ifname 'lo'
        option proto 'static'
        option ipaddr '127.0.0.1'
        option netmask '255.0.0.0'

config globals 'globals'
        option ula_prefix 'fdc9:1542:ecf5::/48'

config interface 'lan'
        option type 'bridge'
        option ifname 'wlan0'
        option proto 'static'
        option ipaddr '192.168.1.1'
        option netmask '255.255.255.0'
        option ip6assign '60'

config interface 'wwan'
        option proto 'dhcp'

config interface 'derp'
        option proto 'static'
        option ipaddr '192.168.10.1'
        option netmask '255.255.255.0'

/etc/config/wireless

config wifi-device 'radio0'
        option type 'mac80211'
        option hwmode '11g'
        option path 'platform/soc/20300000.mmc/mmc_host/mmc1/mmc1:0001/mmc1:0001:1'
        option htmode 'HT20'
        option disabled '0'
        option channel '6'
        option country '00'
        option legacy_rates '1'

config wifi-iface
        option ssid 'aWifiNetwork'
        option encryption 'psk2'
        option device 'radio0'
        option mode 'sta'
        option bssid '88:90:8D:43:E9:A3'
        option key 'SecretPassword'
        option network 'wwan'

config wifi-iface
        option device 'radio0'
        option mode 'ap'
        option ssid 'OpenWrt'
        option encryption 'none'
        option network 'derp'

/etc/config/firewall


config defaults
        option syn_flood '1'
        option input 'ACCEPT'
        option output 'ACCEPT'
        option forward 'REJECT'

config zone
        option name 'lan'
        option input 'ACCEPT'
        option output 'ACCEPT'
        option forward 'ACCEPT'
        option network 'lan wwan derp'

config zone
        option name 'wan'
        option input 'REJECT'
        option output 'ACCEPT'
        option forward 'REJECT'
        option masq '1'
        option mtu_fix '1'
        option network 'wan wan6'

config forwarding
        option src 'lan'
        option dest 'wan'

config rule
        option name 'Allow-DHCP-Renew'
        option src 'wan'
        option proto 'udp'
        option dest_port '68'
        option target 'ACCEPT'
        option family 'ipv4'

config rule
        option name 'Allow-Ping'
        option src 'wan'
        option proto 'icmp'
        option icmp_type 'echo-request'
        option family 'ipv4'
        option target 'ACCEPT'

config rule
        option name 'Allow-IGMP'
        option src 'wan'
        option proto 'igmp'
        option family 'ipv4'
        option target 'ACCEPT'

config rule
        option name 'Allow-DHCPv6'
        option src 'wan'
        option proto 'udp'
        option src_ip 'fc00::/6'
        option dest_ip 'fc00::/6'
        option dest_port '546'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-MLD'
        option src 'wan'
        option proto 'icmp'
        option src_ip 'fe80::/10'
        list icmp_type '130/0'
        list icmp_type '131/0'
        list icmp_type '132/0'
        list icmp_type '143/0'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-ICMPv6-Input'
        option src 'wan'
        option proto 'icmp'
        list icmp_type 'echo-request'
        list icmp_type 'echo-reply'
        list icmp_type 'destination-unreachable'
        list icmp_type 'packet-too-big'
        list icmp_type 'time-exceeded'
        list icmp_type 'bad-header'
        list icmp_type 'unknown-header-type'
        list icmp_type 'router-solicitation'
        list icmp_type 'neighbour-solicitation'
        list icmp_type 'router-advertisement'
        list icmp_type 'neighbour-advertisement'
        option limit '1000/sec'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-ICMPv6-Forward'
        option src 'wan'
        option dest '*'
        option proto 'icmp'
        list icmp_type 'echo-request'
        list icmp_type 'echo-reply'
        list icmp_type 'destination-unreachable'
        list icmp_type 'packet-too-big'
        list icmp_type 'time-exceeded'
        list icmp_type 'bad-header'
        list icmp_type 'unknown-header-type'
        option limit '1000/sec'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-IPSec-ESP'
        option src 'wan'
        option dest 'lan'
        option proto 'esp'
        option target 'ACCEPT'

config rule
        option name 'Allow-ISAKMP'
        option src 'wan'
        option dest 'lan'
        option dest_port '500'
        option proto 'udp'
        option target 'ACCEPT'

config include
        option path '/etc/firewall.user'

I'd really like for this to just be me being stupid.

trendy · May 28, 2020, 2:59pm

Take a look at travelmate. It can do what you need.

jaylthegreat · May 28, 2020, 3:01pm

sorry mate, accidentally posted before i finished writing .

Also i tried it and it did not fix my issue. its possible im an idiot and used it incorrectly, but i believe i read that others have had the same problem

trendy · May 28, 2020, 3:05pm

First of all I don't see the reason to pass those low level commands to configure the wifi and the interfaces.
You can do all these from uci or luci and they will survive a reboot or interface flap.

jaylthegreat · May 28, 2020, 3:08pm

I add the access point through the web interface, this low level stuff was me attempting to troubleshoot

trendy · May 28, 2020, 3:11pm

This is not correct, you want wwan to be part of wan zone. I am not sure about derp, but I guess it doesn't matter so much.

I would suggest to go with travelmate and troubleshoot that here. There is a specific problem with simultaneous client and ap mode which travelmate is handling very well.

STA interfaces operating in an "always off" mode, to make sure that the AP is always accessible

jaylthegreat · May 29, 2020, 3:46pm

travelmate does not seem to be working out about the same as just adding the network.

I'll describe what I've been doing and maybe you can tell me something is wrong.

flash image onto sd card
enable radio and restart the wifi
connect through web interface
go to wireless tab, scan, and connect to internet
update opkg, install travelmate and luci-app-travelmate.

this is where I've tried a few different things, all having the same results

first I try to just use web interface to set it up, so I create the trm_wwan and then add the uplink

next I tried setting the pi back to just being an AP before setting up travelmate through the web interface.

Finally i tried just setting it up manually following instructions from the readme

Each time I would get similar logs. These are just from my last attempt with the manual configuration

dmesg

root@OpenWrt:~# cat dmesg.log
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.214 (buildbot@5b5c16a55686) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7989-82fbd85747) ) #0 Thu Feb 27 21:25:59 2020
[    0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] OF: fdt:Machine model: Raspberry Pi Zero W Rev 1.1
[    0.000000] cma: Reserved 16 MiB at 0x1ac00000
[    0.000000] Memory policy: Data cache writeback
[    0.000000] On node 0 totalpages: 114688
[    0.000000] free_area_init_node: node 0, pgdat c0512000, node_mem_map dbc6a700
[    0.000000]   Normal zone: 896 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 114688 pages, LIFO batch:31
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 113792
[    0.000000] Kernel command line: 8250.nr_uarts=1 bcm2708_fb.fbwidth=1824 bcm2708_fb.fbheight=984 bcm2708_fb.fbswap=1 smsc95xx.macaddr=B8:27:EB:B6:0C:BA vc_mem.mem_base=0x1ec00000 vc_mem.mem_size=0x20000000  dwc_otg.lpm_enable=0 console=ttyS0,115200 kgdboc=ttyS0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=squashfs,ext4 rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 432668K/458752K available (4000K kernel code, 153K rwdata, 716K rodata, 160K init, 353K bss, 9700K reserved, 16384K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xdc800000 - 0xff800000   ( 560 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdc000000   ( 448 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc03f0310   (4001 kB)
[    0.000000]       .init : 0xc04c4000 - 0xc04ec000   ( 160 kB)
[    0.000000]       .data : 0xc04ec000 - 0xc05127e0   ( 154 kB)
[    0.000000]        .bss : 0xc05127e0 - 0xc056ae70   ( 354 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000027] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns
[    0.000076] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns
[    0.000159] bcm2835: system timer (irq = 27)
[    0.000640] Console: colour dummy device 80x30
[    0.001380] console [tty1] enabled
[    0.001443] Calibrating delay loop... 697.95 BogoMIPS (lpj=3489792)
[    0.060312] pid_max: default: 32768 minimum: 301
[    0.060497] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.060557] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.061365] CPU: Testing write buffer coherency: ok
[    0.061785] Setting up static identity map for 0x8200 - 0x825c
[    0.071149] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
[    0.071640] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.071743] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.073945] pinctrl core: initialized pinctrl subsystem
[    0.075526] NET: Registered protocol family 16
[    0.077899] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[    0.086867] cpuidle: using governor ladder
[    0.086955] cpuidle: using governor menu
[    0.087479] Serial: AMBA PL011 UART driver
[    0.091949] bcm2835-mbox 2000b880.mailbox: mailbox enabled
[    0.092672] uart-pl011 20201000.serial: could not find pctldev for node /soc/gpio@7e200000/uart0_pins, deferring probe
[    0.134534] bcm2835-dma 20007000.dma: DMA legacy API manager at dc811000, dmachans=0x1
[    0.137701] SCSI subsystem initialized
[    0.138013] usbcore: registered new interface driver usbfs
[    0.138167] usbcore: registered new interface driver hub
[    0.138312] usbcore: registered new device driver usb
[    0.140676] raspberrypi-firmware soc:firmware: Attached to firmware from 2018-11-23 19:36
[    0.142291] clocksource: Switched to clocksource timer
[    0.153498] NET: Registered protocol family 2
[    0.154593] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.154734] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    0.154845] TCP: Hash tables configured (established 4096 bind 4096)
[    0.154967] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.155034] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.155315] NET: Registered protocol family 1
[    0.156826] Crashlog allocated RAM at address 0x3f00000
[    0.157290] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[    0.167673] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.169865] io scheduler noop registered
[    0.169941] io scheduler deadline registered
[    0.170276] io scheduler cfq registered (default)
[    0.176271] BCM2708FB: allocated DMA memory 5ad00000
[    0.176378] BCM2708FB: allocated DMA channel 0 @ dc811000
[    0.223953] Console: switching to colour frame buffer device 228x61
[    0.261311] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled
[    0.263002] console [ttyS0] disabled
[    0.263255] 20215040.serial: ttyS0 at MMIO 0x0 (irq = 53, base_baud = 31250000) is a 16550
[    0.736121] console [ttyS0] enabled
[    0.741003] vc-cma: Videocore CMA driver
[    0.745247] vc-cma: vc_cma_base      = 0x00000000
[    0.750216] vc-cma: vc_cma_size      = 0x00000000 (0 MiB)
[    0.755941] vc-cma: vc_cma_initial   = 0x00000000 (0 MiB)
[    0.761910] vc-mem: phys_addr:0x00000000 mem_base=0x1ec00000 mem_size:0x20000000(512 MiB)
[    0.790215] brd: module loaded
[    0.803635] loop: module loaded
[    0.807314] usbcore: registered new interface driver smsc95xx
[    0.813487] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    1.047668] Core Release: 2.80a
[    1.051023] Setting default values for core params
[    1.056180] Finished setting default values for core params
[    1.262353] Using Buffer DMA mode
[    1.265884] Periodic Transfer Interrupt Enhancement - disabled
[    1.272024] Multiprocessor Interrupt Enhancement - disabled
[    1.277940] OTG VER PARAM: 0, OTG VER FLAG: 0
[    1.282581] Dedicated Tx FIFOs mode
[    1.286886] WARN::dwc_otg_hcd_init:1053: FIQ DMA bounce buffers: virt = 0xdad14000 dma = 0x5ad14000 len=9024
[    1.297291] FIQ FSM acceleration enabled for :
[    1.297291] Non-periodic Split Transactions
[    1.297291] Periodic Split Transactions
[    1.297291] High-Speed Isochronous Endpoints
[    1.297291] Interrupt/Control Split Transaction hack enabled
[    1.339321] dwc_otg: Microframe scheduler enabled
[    1.339495] WARN::hcd_init_fiq:459: FIQ on core 0 at 0xc02a4d44
[    1.355213] WARN::hcd_init_fiq:460: FIQ ASM at 0xc02a4fc4 length 36
[    1.371131] WARN::hcd_init_fiq:486: MPHI regs_base at 0xdc8c1000
[    1.386829] dwc_otg 20980000.usb: DWC OTG Controller
[    1.401270] dwc_otg 20980000.usb: new USB bus registered, assigned bus number 1
[    1.417905] dwc_otg 20980000.usb: irq 56, io mem 0x00000000
[    1.432714] Init: Port Power? op_state=1
[    1.445744] Init: Power Port (0)
[    1.458437] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.475010] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.491914] usb usb1: Product: DWC OTG Controller
[    1.506132] usb usb1: Manufacturer: Linux 4.9.214 dwc_otg_hcd
[    1.521418] usb usb1: SerialNumber: 20980000.usb
[    1.536421] hub 1-0:1.0: USB hub found
[    1.549555] hub 1-0:1.0: 1 port detected
[    1.563386] dwc_otg: FIQ enabled
[    1.563394] dwc_otg: NAK holdoff enabled
[    1.563401] dwc_otg: FIQ split-transaction FSM enabled
[    1.563422] Module dwc_common_port init
[    1.563808] usbcore: registered new interface driver uas
[    1.578519] usbcore: registered new interface driver usb-storage
[    1.593797] mousedev: PS/2 mouse device common for all mice
[    1.609896] bcm2835-wdt 20100000.watchdog: Broadcom BCM2835 watchdog timer
[    1.626741] bcm2835-cpufreq: min=700000 max=1000000
[    1.641659] sdhci: Secure Digital Host Controller Interface driver
[    1.657245] sdhci: Copyright(c) Pierre Ossman
[    1.671731] sdhost: log_buf @ dad13000 (5ad13000)
[    1.762357] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[    1.777142] mmc-bcm2835 20300000.mmc: mmc_debug:0 mmc_debug2:0
[    1.789788] mmc-bcm2835 20300000.mmc: DMA channel allocated
[    1.823234] Indeed it is in host mode hprt0 = 00041901
[    1.901069] random: fast init done
[    1.922478] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.937749] vchiq: vchiq_init_state: slot_zero = 0xdad80000, is_master = 0
[    1.960966] NET: Registered protocol family 10
[    1.975947] NET: Registered protocol family 17
[    1.987182] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    2.007143] 8021q: 802.1Q VLAN Support v1.8
[    2.021976] vc-sm: Videocore shared memory driver
[    2.033867] [vc_sm_connected_init]: start
[    2.044755] usb 1-1: new low-speed USB device number 2 using dwc_otg
[    2.059532] Indeed it is in host mode hprt0 = 00041901
[    2.132506] [vc_sm_connected_init]: end - returning 0
[    2.147695] 20201000.serial: ttyAMA0 at MMIO 0x20201000 (irq = 81, base_baud = 0) is a PL011 rev2
[    2.164389] of_cfs_init
[    2.173823] of_cfs_init: OK
[    2.184525] mmc0: host does not support reading read-only switch, assuming write-enable
[    2.200228] Waiting for root device /dev/mmcblk0p2...
[    2.213366] mmc0: new high speed SDHC card at address 0001
[    2.226959] mmcblk0: mmc0:0001 00000 29.1 GiB
[    2.240858]  mmcblk0: p1 p2
[    2.254101] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[    2.268489] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    2.282443] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    2.297499] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[    2.328966] usb 1-1: New USB device found, idVendor=413c, idProduct=2003
[    2.342606] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.356635] usb 1-1: Product: Dell USB Keyboard
[    2.367976] usb 1-1: Manufacturer: Dell
[    2.453491] mmc1: new high speed SDIO card at address 0001
[    2.503602] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null)
[    2.518226] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[    2.532331] Freeing unused kernel memory: 160K
[    2.543444] This architecture does not have kernel memory protection.
[    2.626487] init: Console is alive
[    2.637381] init: - watchdog -
[    2.805884] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    2.828494] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    2.856227] init: - preinit -
[    3.160886] random: jshn: uninitialized urandom read (4 bytes read)
[    3.218303] random: jshn: uninitialized urandom read (4 bytes read)
[    3.263681] random: jshn: uninitialized urandom read (4 bytes read)
[    6.493831] mount_root: mounting /dev/root
[    6.510234] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[    6.614224] urandom-seed: Seeding with /etc/urandom.seed
[    6.676747] procd: - early -
[    6.689823] procd: - watchdog -
[    7.353549] procd: - watchdog -
[    7.364300] procd: - ubus -
[    7.392633] urandom_read: 1 callbacks suppressed
[    7.392645] random: ubusd: uninitialized urandom read (4 bytes read)
[    7.429995] random: ubusd: uninitialized urandom read (4 bytes read)
[    7.446591] random: ubusd: uninitialized urandom read (4 bytes read)
[    7.464230] procd: - init -
[    7.756455] kmodloader: loading kernel modules from /etc/modules.d/*
[    7.805984] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    7.834045] hidraw: raw HID events driver (C) Jiri Kosina
[    7.877909] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[    7.893098] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[    7.910883] ip_tables: (C) 2000-2006 Netfilter Core Team
[    7.931328] nf_conntrack version 0.5.0 (7168 buckets, 28672 max)
[    7.988136] input: Dell Dell USB Keyboard as /devices/platform/soc/20980000.usb/usb1/1-1/1-1:1.0/0003:413C:2003.0001/input/input0
[    8.072895] hid-generic 0003:413C:2003.0001: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-20980000.usb-1/input0
[    8.092860] usbcore: registered new interface driver usbhid
[    8.105633] usbhid: USB HID core driver
[    8.133362] xt_time: kernel timezone is -0000
[    8.169338] PPP generic driver version 2.4.2
[    8.182979] NET: Registered protocol family 24
[    8.210547] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430-sdio for chip BCM43430/1
[    8.246561] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43430-sdio.raspberrypi,model-zero-w.txt failed with error -2
[    8.265825] brcmfmac mmc1:0001:1: Falling back to user helper
[    8.296806] firmware brcm!brcmfmac43430-sdio.raspberrypi,model-zero-w.txt: firmware_loading_store: map pages failed
[    8.404911] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430-sdio for chip BCM43430/1
[    8.421484] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43430-sdio.clm_blob failed with error -2
[    8.439429] brcmfmac mmc1:0001:1: Falling back to user helper
[    8.469603] firmware brcm!brcmfmac43430-sdio.clm_blob: firmware_loading_store: map pages failed
[    8.486567] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-11), device may have limited channels available
[    8.511427] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43430/1 wl0: Aug 29 2016 20:48:16 version 7.45.41.26 (r640327) FWID 01-4527cfab
[    8.569828] usbcore: registered new interface driver brcmfmac
[    8.600724] kmodloader: done loading kernel modules from /etc/modules.d/*
[   15.974789] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   18.532284] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   18.595965] br-lan: port 1(wlan0) entered blocking state
[   18.609456] br-lan: port 1(wlan0) entered disabled state
[   18.623420] device wlan0 entered promiscuous mode
[   18.863440] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   18.878121] br-lan: port 1(wlan0) entered blocking state
[   18.891527] br-lan: port 1(wlan0) entered forwarding state
[   19.081215] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   20.135415] random: crng init done
[   20.146584] random: 3 urandom warning(s) missed due to ratelimiting
[   22.322601] device wlan0 left promiscuous mode
[   22.335468] br-lan: port 1(wlan0) entered disabled state
[   23.455020] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   24.923390] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
[   24.966059] br-lan: port 1(wlan0-1) entered blocking state
[   24.977819] br-lan: port 1(wlan0-1) entered disabled state
[   24.990176] device wlan0-1 entered promiscuous mode
[   25.001595] br-lan: port 1(wlan0-1) entered blocking state
[   25.013113] br-lan: port 1(wlan0-1) entered forwarding state
[   25.028133] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   25.242075] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   25.412414] br-lan: port 1(wlan0-1) entered disabled state
[   26.214035] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   26.380389] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[   26.396001] br-lan: port 1(wlan0-1) entered blocking state
[   26.409999] br-lan: port 1(wlan0-1) entered forwarding state
[   26.910691] br-lan: port 1(wlan0-1) entered disabled state
[   27.668365] br-lan: port 1(wlan0-1) entered blocking state
[   27.679784] br-lan: port 1(wlan0-1) entered forwarding state
[   28.171804] br-lan: port 1(wlan0-1) entered disabled state
[   28.890917] br-lan: port 1(wlan0-1) entered blocking state
[   28.902645] br-lan: port 1(wlan0-1) entered forwarding state
[   29.382431] br-lan: port 1(wlan0-1) entered disabled state
[   30.121544] br-lan: port 1(wlan0-1) entered blocking state
[   30.133241] br-lan: port 1(wlan0-1) entered forwarding state
[   30.615616] br-lan: port 1(wlan0-1) entered disabled state
[   31.222928] br-lan: port 1(wlan0-1) entered blocking state
[   31.234493] br-lan: port 1(wlan0-1) entered forwarding state
[   41.575762] br-lan: port 1(wlan0-1) entered disabled state
[   43.340166] br-lan: port 1(wlan0-1) entered blocking state
[   43.353790] br-lan: port 1(wlan0-1) entered forwarding state
[   54.048000] br-lan: port 1(wlan0-1) entered disabled state
[   54.298297] br-lan: port 1(wlan0-1) entered blocking state
[   54.311535] br-lan: port 1(wlan0-1) entered forwarding state
[   55.123449] br-lan: port 1(wlan0-1) entered disabled state
[   55.457975] br-lan: port 1(wlan0-1) entered blocking state
[   55.471562] br-lan: port 1(wlan0-1) entered forwarding state
[   56.164535] br-lan: port 1(wlan0-1) entered disabled state
[   56.681564] ieee80211 phy0: brcmf_cfg80211_start_ap: SET SSID error (-512)
[   56.694377] ieee80211 phy0: brcmf_set_mpc: fail to set mpc
[   56.744668] device wlan0-1 left promiscuous mode
[   56.755505] br-lan: port 1(wlan0-1) entered disabled state
[   67.346580] ieee80211 phy0: brcmf_cfg80211_get_channel: chanspec failed (-52)
[   67.424240] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   68.482556] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   68.527161] br-lan: port 1(wlan0) entered blocking state
[   68.539101] br-lan: port 1(wlan0) entered disabled state
[   68.551455] device wlan0 entered promiscuous mode
[   68.666187] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   68.679150] br-lan: port 1(wlan0) entered blocking state
[   68.690897] br-lan: port 1(wlan0) entered forwarding state
[   68.794735] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   73.276306] device wlan0 left promiscuous mode
[   73.287408] br-lan: port 1(wlan0) entered disabled state
[   75.170620] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
[   75.230606] br-lan: port 1(wlan0-1) entered blocking state
[   75.242715] br-lan: port 1(wlan0-1) entered disabled state
[   75.255474] device wlan0-1 entered promiscuous mode
[   75.267271] br-lan: port 1(wlan0-1) entered blocking state
[   75.279162] br-lan: port 1(wlan0-1) entered forwarding state
[   75.313089] br-lan: port 1(wlan0-1) entered disabled state
[   75.502882] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   77.125319] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   77.291083] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[   77.304557] br-lan: port 1(wlan0-1) entered blocking state
[   77.316642] br-lan: port 1(wlan0-1) entered forwarding state
[   77.805325] br-lan: port 1(wlan0-1) entered disabled state
[   78.567598] br-lan: port 1(wlan0-1) entered blocking state
[   78.581849] br-lan: port 1(wlan0-1) entered forwarding state
[   79.077400] br-lan: port 1(wlan0-1) entered disabled state
[   79.787971] br-lan: port 1(wlan0-1) entered blocking state
[   79.799867] br-lan: port 1(wlan0-1) entered forwarding state
[   80.286374] br-lan: port 1(wlan0-1) entered disabled state
[   81.013168] br-lan: port 1(wlan0-1) entered blocking state
[   81.026797] br-lan: port 1(wlan0-1) entered forwarding state
[   82.840366] br-lan: port 1(wlan0-1) entered disabled state
[   83.061246] br-lan: port 1(wlan0-1) entered blocking state
[   83.074891] br-lan: port 1(wlan0-1) entered forwarding state
[   83.843394] br-lan: port 1(wlan0-1) entered disabled state
[   84.293652] br-lan: port 1(wlan0-1) entered blocking state
[   84.304984] br-lan: port 1(wlan0-1) entered forwarding state
[   84.861148] br-lan: port 1(wlan0-1) entered disabled state
[   85.518111] br-lan: port 1(wlan0-1) entered blocking state
[   85.528922] br-lan: port 1(wlan0-1) entered forwarding state
[   86.015549] br-lan: port 1(wlan0-1) entered disabled state
[   86.747525] br-lan: port 1(wlan0-1) entered blocking state
[   86.760152] br-lan: port 1(wlan0-1) entered forwarding state
[   87.244860] br-lan: port 1(wlan0-1) entered disabled state
[   87.723679] br-lan: port 1(wlan0-1) entered blocking state
[   87.734543] br-lan: port 1(wlan0-1) entered forwarding state
[   97.762338] ieee80211 phy0: brcmf_escan_timeout: timer expired
[   98.239574] br-lan: port 1(wlan0-1) entered disabled state
[   98.527925] br-lan: port 1(wlan0-1) entered blocking state
[   98.540735] br-lan: port 1(wlan0-1) entered forwarding state
[   99.283413] br-lan: port 1(wlan0-1) entered disabled state
[   99.757218] br-lan: port 1(wlan0-1) entered blocking state
[   99.769847] br-lan: port 1(wlan0-1) entered forwarding state
[  100.293349] br-lan: port 1(wlan0-1) entered disabled state
[  100.993662] br-lan: port 1(wlan0-1) entered blocking state
[  101.004262] br-lan: port 1(wlan0-1) entered forwarding state
[  101.481951] br-lan: port 1(wlan0-1) entered disabled state
[  105.972377] br-lan: port 1(wlan0-1) entered blocking state
[  105.984714] br-lan: port 1(wlan0-1) entered forwarding state
[  109.052709] br-lan: port 1(wlan0-1) entered disabled state
[  109.068537] device wlan0-1 left promiscuous mode
[  109.077912] br-lan: port 1(wlan0-1) entered disabled state
[  110.215900] ieee80211 phy0: brcmf_cfg80211_get_channel: chanspec failed (-52)
[  110.304137] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[  111.510936] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  111.545995] br-lan: port 1(wlan0) entered blocking state
[  111.556411] br-lan: port 1(wlan0) entered disabled state
[  111.567135] device wlan0 entered promiscuous mode
[  111.846828] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  111.858542] br-lan: port 1(wlan0) entered blocking state
[  111.868875] br-lan: port 1(wlan0) entered forwarding state
[  111.988648] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[  125.449821] device wlan0 left promiscuous mode
[  125.459268] br-lan: port 1(wlan0) entered disabled state
[  127.315727] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
[  127.366242] br-lan: port 1(wlan0-1) entered blocking state
[  127.376560] br-lan: port 1(wlan0-1) entered disabled state
[  127.387359] device wlan0-1 entered promiscuous mode
[  127.397398] br-lan: port 1(wlan0-1) entered blocking state
[  127.407937] br-lan: port 1(wlan0-1) entered forwarding state
[  127.482447] br-lan: port 1(wlan0-1) entered disabled state
[  127.649890] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  128.635417] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  128.794295] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[  128.806428] br-lan: port 1(wlan0-1) entered blocking state
[  128.817193] br-lan: port 1(wlan0-1) entered forwarding state
[  129.573257] br-lan: port 1(wlan0-1) entered disabled state
[  130.069966] br-lan: port 1(wlan0-1) entered blocking state
[  130.082595] br-lan: port 1(wlan0-1) entered forwarding state
[  130.583479] br-lan: port 1(wlan0-1) entered disabled state
[  131.304679] br-lan: port 1(wlan0-1) entered blocking state
[  131.315530] br-lan: port 1(wlan0-1) entered forwarding state
[  131.795692] br-lan: port 1(wlan0-1) entered disabled state
[  132.524105] br-lan: port 1(wlan0-1) entered blocking state
[  132.536933] br-lan: port 1(wlan0-1) entered forwarding state
[  133.024201] br-lan: port 1(wlan0-1) entered disabled state
[  133.626952] br-lan: port 1(wlan0-1) entered blocking state
[  133.637790] br-lan: port 1(wlan0-1) entered forwarding state
[  134.123620] br-lan: port 1(wlan0-1) entered disabled state
[  134.402217] br-lan: port 1(wlan0-1) entered blocking state
[  134.414720] br-lan: port 1(wlan0-1) entered forwarding state
[  135.203280] br-lan: port 1(wlan0-1) entered disabled state
[  135.591184] br-lan: port 1(wlan0-1) entered blocking state
[  135.603794] br-lan: port 1(wlan0-1) entered forwarding state
[  136.228463] br-lan: port 1(wlan0-1) entered disabled state
[  136.840020] br-lan: port 1(wlan0-1) entered blocking state
[  136.850723] br-lan: port 1(wlan0-1) entered forwarding state
[  137.333622] br-lan: port 1(wlan0-1) entered disabled state
[  138.057298] br-lan: port 1(wlan0-1) entered blocking state
[  138.069931] br-lan: port 1(wlan0-1) entered forwarding state
[  138.553481] br-lan: port 1(wlan0-1) entered disabled state
[  139.283311] br-lan: port 1(wlan0-1) entered blocking state
[  139.293668] br-lan: port 1(wlan0-1) entered forwarding state
[  141.067572] br-lan: port 1(wlan0-1) entered disabled state
[  141.379381] br-lan: port 1(wlan0-1) entered blocking state
[  141.390053] br-lan: port 1(wlan0-1) entered forwarding state
[  142.083480] br-lan: port 1(wlan0-1) entered disabled state
[  142.580017] br-lan: port 1(wlan0-1) entered blocking state
[  142.592186] br-lan: port 1(wlan0-1) entered forwarding state
[  143.093438] br-lan: port 1(wlan0-1) entered disabled state
[  143.788911] br-lan: port 1(wlan0-1) entered blocking state
[  143.799222] br-lan: port 1(wlan0-1) entered forwarding state
[  144.286209] br-lan: port 1(wlan0-1) entered disabled state
[  145.018064] br-lan: port 1(wlan0-1) entered blocking state
[  145.029655] br-lan: port 1(wlan0-1) entered forwarding state
[  145.519849] br-lan: port 1(wlan0-1) entered disabled state
[  145.988105] br-lan: port 1(wlan0-1) entered blocking state
[  145.998096] br-lan: port 1(wlan0-1) entered forwarding state
[  156.002333] ieee80211 phy0: brcmf_escan_timeout: timer expired
[  156.480784] br-lan: port 1(wlan0-1) entered disabled state
[  157.687076] br-lan: port 1(wlan0-1) entered blocking state
[  157.698380] br-lan: port 1(wlan0-1) entered forwarding state
[  159.545115] br-lan: port 1(wlan0-1) entered disabled state
[  162.323816] br-lan: port 1(wlan0-1) entered blocking state
[  162.335088] br-lan: port 1(wlan0-1) entered forwarding state
[  163.193245] br-lan: port 1(wlan0-1) entered disabled state
[  163.312279] device wlan0-1 left promiscuous mode
[  163.321282] br-lan: port 1(wlan0-1) entered disabled state
[  164.484260] ieee80211 phy0: brcmf_cfg80211_get_channel: chanspec failed (-52)
[  164.549856] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[  165.813214] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  165.855748] br-lan: port 1(wlan0) entered blocking state
[  165.865564] br-lan: port 1(wlan0) entered disabled state
[  165.875688] device wlan0 entered promiscuous mode
[  166.128989] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  166.140347] br-lan: port 1(wlan0) entered blocking state
[  166.150245] br-lan: port 1(wlan0) entered forwarding state
[  166.278468] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready

I notice that it eventually puts my router on the faulty list. I know that i used the right password and everything.

if more details are needed. please let me know

trendy · May 29, 2020, 4:14pm

What is the output of iw list ?

jaylthegreat · May 29, 2020, 4:19pm

I will need a few minutes. In the meantime here is the logread. with just the travelmate portions as it was far too long otherwise.

logread

Fri May 29 15:06:42 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: sta, name: wlan0, status: false, quality: 0, connection: -, wait: 31, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:06:42 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: @wifi-iface[1], status: not connected, sta_iface: trm_wwan, sta_radio: radio0, sta_essid: MyWifiSSID, sta_bssid: 88:90:8D:43:E9:A3, faulty_list: -
Fri May 29 15:06:42 2020 user.info travelmate-1.2.2[440]: can't connect to uplink 'radio0/MyWifiSSID/88:90:8D:43:E9:A3' (Raspberry Pi Zero W Rev 1.1, OpenWrt 18.06.8 r7989-82fbd85747)
Fri May 29 15:06:52 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: rev, name: -, status: false, quality: 0, connection: -, wait: 10, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:06:59 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 90,88:90:8D:43:E9:A3,"MyWifiSSID",90,88:90:8D:43:E9:A2,unknown,90,88:90:8D:43:E9:A0,unknown,61,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",60,34:97:F6:08:FB:02,"5291",47,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",42,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",41,3A:22:E2:94:43:BD,"DIRECT-BD-HP OfficeJet Pro 8020",40,8C:FE:74:39:84:E8,"CableWiFi",38,8C:FE:74:B9:84:E8,"SpectrumWiFi",34,8C:FE:74:79:84:E8,"SpectrumWiFi Plus",, cnt: 3, max_cnt: 3
Fri May 29 15:06:59 2020 user.debug travelmate-1.2.2[440]: f_main ::: scan_quality: 90, scan_bssid: 88:90:8D:43:E9:A3, scan_essid: "MyWifiSSID"
Fri May 29 15:07:37 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: sta, name: wlan0, status: false, quality: 0, connection: -, wait: 31, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:07:37 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: @wifi-iface[1], status: not connected, sta_iface: trm_wwan, sta_radio: radio0, sta_essid: MyWifiSSID, sta_bssid: 88:90:8D:43:E9:A3, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:07:37 2020 user.info travelmate-1.2.2[440]: can't connect to uplink 'radio0/MyWifiSSID/88:90:8D:43:E9:A3', uplink disabled (Raspberry Pi Zero W Rev 1.1, OpenWrt 18.06.8 r7989-82fbd85747)
Fri May 29 15:07:47 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: rev, name: -, status: false, quality: 0, connection: -, wait: 10, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:08:52 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: -, status: not connected, sta_iface: -, sta_radio: -, sta_essid: -, sta_bssid: -, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:08:52 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: initial, name: -, status: false, quality: 0, connection: -, wait: 1, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:08:52 2020 user.debug travelmate-1.2.2[440]: f_prep ::: config: cfg023579, mode: ap, network: lan, eap_rc: 0, radio: radio0, trm_radio: -, disabled:
Fri May 29 15:08:53 2020 user.debug travelmate-1.2.2[440]: f_prep ::: config: cfg033579, mode: sta, network: trm_wwan, eap_rc: 0, radio: radio0, trm_radio: -, disabled: 1
Fri May 29 15:08:53 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: -, status: running, sta_iface: -, sta_radio: -, sta_essid: -, sta_bssid: -, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:08:53 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: dev, name:  radio0, status: running, quality: 0, connection: -, wait: 1, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:08:53 2020 user.debug travelmate-1.2.2[440]: f_main ::: iwinfo: /usr/bin/iwinfo, dev_list:  radio0, sta_list:  cfg033579_radio0, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:08:54 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 88,88:90:8D:43:E9:A2,unknown,85,88:90:8D:43:E9:A3,"MyWifiSSID",85,88:90:8D:43:E9:A0,unknown,67,34:97:F6:08:FB:02,"5291",57,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",55,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",47,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",34,34:64:A9:08:41:09,"HP-Print-09-Officejet Pro 6830",, cnt: 1, max_cnt: 3
Fri May 29 15:09:01 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 85,88:90:8D:43:E9:A3,"MyWifiSSID",85,88:90:8D:43:E9:A2,unknown,85,88:90:8D:43:E9:A0,unknown,64,34:97:F6:08:FB:02,"5291",58,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",54,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",42,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",34,34:64:A9:08:41:09,"HP-Print-09-Officejet Pro 6830",, cnt: 2, max_cnt: 3
Fri May 29 15:09:08 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 85,88:90:8D:43:E9:A3,"MyWifiSSID",85,88:90:8D:43:E9:A2,unknown,85,88:90:8D:43:E9:A0,unknown,65,34:97:F6:08:FB:02,"5291",58,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",57,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",48,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",37,40:B0:34:D1:FC:D8,"DIRECT-D6-HP OfficeJet Pro 6960",34,34:64:A9:08:41:09,"HP-Print-09-Officejet Pro 6830",, cnt: 3, max_cnt: 3
Fri May 29 15:10:13 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: -, status: not connected, sta_iface: -, sta_radio: -, sta_essid: -, sta_bssid: -, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:10:13 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: initial, name: -, status: false, quality: 0, connection: -, wait: 1, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:10:13 2020 user.debug travelmate-1.2.2[440]: f_prep ::: config: cfg023579, mode: ap, network: lan, eap_rc: 0, radio: radio0, trm_radio: -, disabled:
Fri May 29 15:10:13 2020 user.debug travelmate-1.2.2[440]: f_prep ::: config: cfg033579, mode: sta, network: trm_wwan, eap_rc: 0, radio: radio0, trm_radio: -, disabled: 1
Fri May 29 15:10:13 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: -, status: running, sta_iface: -, sta_radio: -, sta_essid: -, sta_bssid: -, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:10:13 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: dev, name:  radio0, status: running, quality: 0, connection: -, wait: 1, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:10:13 2020 user.debug travelmate-1.2.2[440]: f_main ::: iwinfo: /usr/bin/iwinfo, dev_list:  radio0, sta_list:  cfg033579_radio0, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:10:15 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 88,88:90:8D:43:E9:A3,"MyWifiSSID",88,88:90:8D:43:E9:A2,unknown,84,88:90:8D:43:E9:A0,unknown,65,34:97:F6:08:FB:02,"5291",60,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",54,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",45,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",, cnt: 1, max_cnt: 3
Fri May 29 15:10:22 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 87,88:90:8D:43:E9:A2,unknown,85,88:90:8D:43:E9:A3,"MyWifiSSID",85,88:90:8D:43:E9:A0,unknown,65,34:97:F6:08:FB:02,"5291",58,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",57,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",47,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",, cnt: 2, max_cnt: 3
Fri May 29 15:10:29 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 87,88:90:8D:43:E9:A2,unknown,85,88:90:8D:43:E9:A3,"MyWifiSSID",85,88:90:8D:43:E9:A0,unknown,68,34:97:F6:08:FB:02,"5291",54,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",48,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",47,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",, cnt: 3, max_cnt: 3
Fri May 29 15:11:34 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: -, status: not connected, sta_iface: -, sta_radio: -, sta_essid: -, sta_bssid: -, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:11:34 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: initial, name: -, status: false, quality: 0, connection: -, wait: 1, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:11:34 2020 user.debug travelmate-1.2.2[440]: f_prep ::: config: cfg023579, mode: ap, network: lan, eap_rc: 0, radio: radio0, trm_radio: -, disabled:
Fri May 29 15:11:34 2020 user.debug travelmate-1.2.2[440]: f_prep ::: config: cfg033579, mode: sta, network: trm_wwan, eap_rc: 0, radio: radio0, trm_radio: -, disabled: 1
Fri May 29 15:11:34 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: -, status: running, sta_iface: -, sta_radio: -, sta_essid: -, sta_bssid: -, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:11:34 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: dev, name:  radio0, status: running, quality: 0, connection: -, wait: 1, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:11:34 2020 user.debug travelmate-1.2.2[440]: f_main ::: iwinfo: /usr/bin/iwinfo, dev_list:  radio0, sta_list:  cfg033579_radio0, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:11:36 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 88,88:90:8D:43:E9:A2,unknown,85,88:90:8D:43:E9:A3,"MyWifiSSID",85,88:90:8D:43:E9:A0,unknown,57,34:97:F6:08:FB:02,"5291",55,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",54,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",48,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",45,3A:22:E2:94:43:BD,"DIRECT-BD-HP OfficeJet Pro 8020",35,34:64:A9:08:41:09,"HP-Print-09-Officejet Pro 6830",, cnt: 1, max_cnt: 3
Fri May 29 15:11:43 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 87,88:90:8D:43:E9:A0,unknown,85,88:90:8D:43:E9:A2,unknown,84,88:90:8D:43:E9:A3,"MyWifiSSID",57,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",55,34:97:F6:08:FB:02,"5291",50,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",45,3A:22:E2:94:43:BD,"DIRECT-BD-HP OfficeJet Pro 8020",44,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",35,34:64:A9:08:41:09,"HP-Print-09-Officejet Pro 6830",, cnt: 2, max_cnt: 3
Fri May 29 15:11:50 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 87,88:90:8D:43:E9:A2,unknown,87,88:90:8D:43:E9:A0,unknown,85,88:90:8D:43:E9:A3,"MyWifiSSID",57,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",57,34:97:F6:08:FB:02,"5291",52,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",47,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",38,3A:22:E2:94:43:BD,"DIRECT-BD-HP OfficeJet Pro 8020",37,8C:FE:74:39:84:E8,"CableWiFi",32,34:64:A9:08:41:09,"HP-Print-09-Officejet Pro 6830",, cnt: 3, max_cnt: 3
Fri May 29 15:12:55 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: -, status: not connected, sta_iface: -, sta_radio: -, sta_essid: -, sta_bssid: -, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:12:55 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: initial, name: -, status: false, quality: 0, connection: -, wait: 1, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:12:55 2020 user.debug travelmate-1.2.2[440]: f_prep ::: config: cfg023579, mode: ap, network: lan, eap_rc: 0, radio: radio0, trm_radio: -, disabled:
Fri May 29 15:12:55 2020 user.debug travelmate-1.2.2[440]: f_prep ::: config: cfg033579, mode: sta, network: trm_wwan, eap_rc: 0, radio: radio0, trm_radio: -, disabled: 1
Fri May 29 15:12:55 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: -, status: running, sta_iface: -, sta_radio: -, sta_essid: -, sta_bssid: -, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:12:55 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: dev, name:  radio0, status: running, quality: 0, connection: -, wait: 1, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:12:55 2020 user.debug travelmate-1.2.2[440]: f_main ::: iwinfo: /usr/bin/iwinfo, dev_list:  radio0, sta_list:  cfg033579_radio0, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:12:57 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 87,88:90:8D:43:E9:A3,"MyWifiSSID",85,88:90:8D:43:E9:A2,unknown,85,88:90:8D:43:E9:A0,unknown,61,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",55,34:97:F6:08:FB:02,"5291",47,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",47,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",, cnt: 1, max_cnt: 3
Fri May 29 15:13:04 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 88,88:90:8D:43:E9:A2,unknown,88,88:90:8D:43:E9:A0,unknown,87,88:90:8D:43:E9:A3,"MyWifiSSID",60,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",58,34:97:F6:08:FB:02,"5291",48,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",45,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",, cnt: 2, max_cnt: 3
Fri May 29 15:13:10 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 88,88:90:8D:43:E9:A3,"MyWifiSSID",88,88:90:8D:43:E9:A2,unknown,85,88:90:8D:43:E9:A0,unknown,58,34:97:F6:08:FB:02,"5291",57,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",51,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",45,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",, cnt: 3, max_cnt: 3
Fri May 29 15:14:16 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: -, status: not connected, sta_iface: -, sta_radio: -, sta_essid: -, sta_bssid: -, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:14:16 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: initial, name: -, status: false, quality: 0, connection: -, wait: 1, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:14:16 2020 user.debug travelmate-1.2.2[440]: f_prep ::: config: cfg023579, mode: ap, network: lan, eap_rc: 0, radio: radio0, trm_radio: -, disabled:
Fri May 29 15:14:16 2020 user.debug travelmate-1.2.2[440]: f_prep ::: config: cfg033579, mode: sta, network: trm_wwan, eap_rc: 0, radio: radio0, trm_radio: -, disabled: 1
Fri May 29 15:14:16 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: -, status: running, sta_iface: -, sta_radio: -, sta_essid: -, sta_bssid: -, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:14:16 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: dev, name:  radio0, status: running, quality: 0, connection: -, wait: 1, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:14:16 2020 user.debug travelmate-1.2.2[440]: f_main ::: iwinfo: /usr/bin/iwinfo, dev_list:  radio0, sta_list:  cfg033579_radio0, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:14:18 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 88,88:90:8D:43:E9:A0,unknown,87,88:90:8D:43:E9:A3,"MyWifiSSID",85,88:90:8D:43:E9:A2,unknown,60,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",60,34:97:F6:08:FB:02,"5291",44,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",42,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",37,40:B0:34:D1:FC:D8,"DIRECT-D6-HP OfficeJet Pro 6960",, cnt: 1, max_cnt: 3
Fri May 29 15:14:24 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 90,88:90:8D:43:E9:A2,unknown,88,88:90:8D:43:E9:A0,unknown,84,88:90:8D:43:E9:A3,"MyWifiSSID",71,34:97:F6:08:FB:02,"5291",61,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",44,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",42,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",38,3A:22:E2:94:43:BD,"DIRECT-BD-HP OfficeJet Pro 8020",37,40:B0:34:D1:FC:D8,"DIRECT-D6-HP OfficeJet Pro 6960",, cnt: 2, max_cnt: 3
Fri May 29 15:14:31 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 88,88:90:8D:43:E9:A3,"MyWifiSSID",87,88:90:8D:43:E9:A0,unknown,85,88:90:8D:43:E9:A2,unknown,68,34:97:F6:08:FB:02,"5291",58,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",57,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",42,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",38,3A:22:E2:94:43:BD,"DIRECT-BD-HP OfficeJet Pro 8020",37,40:B0:34:D1:FC:D8,"DIRECT-D6-HP OfficeJet Pro 6960",, cnt: 3, max_cnt: 3
Fri May 29 15:15:37 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: -, status: not connected, sta_iface: -, sta_radio: -, sta_essid: -, sta_bssid: -, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:15:37 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: initial, name: -, status: false, quality: 0, connection: -, wait: 1, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:15:37 2020 user.debug travelmate-1.2.2[440]: f_prep ::: config: cfg023579, mode: ap, network: lan, eap_rc: 0, radio: radio0, trm_radio: -, disabled:
Fri May 29 15:15:37 2020 user.debug travelmate-1.2.2[440]: f_prep ::: config: cfg033579, mode: sta, network: trm_wwan, eap_rc: 0, radio: radio0, trm_radio: -, disabled: 1
Fri May 29 15:15:37 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: -, status: running, sta_iface: -, sta_radio: -, sta_essid: -, sta_bssid: -, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:15:37 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: dev, name:  radio0, status: running, quality: 0, connection: -, wait: 1, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:15:37 2020 user.debug travelmate-1.2.2[440]: f_main ::: iwinfo: /usr/bin/iwinfo, dev_list:  radio0, sta_list:  cfg033579_radio0, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:15:39 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 90,88:90:8D:43:E9:A3,"MyWifiSSID",88,88:90:8D:43:E9:A2,unknown,87,88:90:8D:43:E9:A0,unknown,67,34:97:F6:08:FB:02,"5291",61,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",57,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",, cnt: 1, max_cnt: 3
Fri May 29 15:15:45 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 87,88:90:8D:43:E9:A2,unknown,85,88:90:8D:43:E9:A3,"MyWifiSSID",85,88:90:8D:43:E9:A0,unknown,68,34:97:F6:08:FB:02,"5291",61,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",57,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",41,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",, cnt: 2, max_cnt: 3
Fri May 29 15:15:52 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 88,88:90:8D:43:E9:A0,unknown,85,88:90:8D:43:E9:A3,"MyWifiSSID",85,88:90:8D:43:E9:A2,unknown,64,34:97:F6:08:FB:02,"5291",62,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",52,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",42,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",, cnt: 3, max_cnt: 3
Fri May 29 15:16:57 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: -, status: not connected, sta_iface: -, sta_radio: -, sta_essid: -, sta_bssid: -, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:16:57 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: initial, name: -, status: false, quality: 0, connection: -, wait: 1, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:16:58 2020 user.debug travelmate-1.2.2[440]: f_prep ::: config: cfg023579, mode: ap, network: lan, eap_rc: 0, radio: radio0, trm_radio: -, disabled:
Fri May 29 15:16:58 2020 user.debug travelmate-1.2.2[440]: f_prep ::: config: cfg033579, mode: sta, network: trm_wwan, eap_rc: 0, radio: radio0, trm_radio: -, disabled: 1
Fri May 29 15:16:58 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: -, status: running, sta_iface: -, sta_radio: -, sta_essid: -, sta_bssid: -, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:16:58 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: dev, name:  radio0, status: running, quality: 0, connection: -, wait: 1, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:16:58 2020 user.debug travelmate-1.2.2[440]: f_main ::: iwinfo: /usr/bin/iwinfo, dev_list:  radio0, sta_list:  cfg033579_radio0, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:16:59 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 88,88:90:8D:43:E9:A2,unknown,87,88:90:8D:43:E9:A0,unknown,82,88:90:8D:43:E9:A3,"MyWifiSSID",68,34:97:F6:08:FB:02,"5291",61,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",55,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",42,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",, cnt: 1, max_cnt: 3
Fri May 29 15:17:06 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 90,88:90:8D:43:E9:A2,unknown,85,88:90:8D:43:E9:A3,"MyWifiSSID",85,88:90:8D:43:E9:A0,unknown,65,34:97:F6:08:FB:02,"5291",61,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",55,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",47,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",30,8C:FE:74:39:84:E8,"CableWiFi",, cnt: 2, max_cnt: 3
Fri May 29 15:17:13 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 88,88:90:8D:43:E9:A2,unknown,87,88:90:8D:43:E9:A0,unknown,85,88:90:8D:43:E9:A3,"MyWifiSSID",72,34:97:F6:08:FB:02,"5291",64,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",54,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",47,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",47,3A:22:E2:94:43:BD,"DIRECT-BD-HP OfficeJet Pro 8020",30,8C:FE:74:39:84:E8,"CableWiFi",, cnt: 3, max_cnt: 3
Fri May 29 15:18:18 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: -, status: not connected, sta_iface: -, sta_radio: -, sta_essid: -, sta_bssid: -, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:18:18 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: initial, name: -, status: false, quality: 0, connection: -, wait: 1, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:18:18 2020 user.debug travelmate-1.2.2[440]: f_prep ::: config: cfg023579, mode: ap, network: lan, eap_rc: 0, radio: radio0, trm_radio: -, disabled:
Fri May 29 15:18:18 2020 user.debug travelmate-1.2.2[440]: f_prep ::: config: cfg033579, mode: sta, network: trm_wwan, eap_rc: 0, radio: radio0, trm_radio: -, disabled: 1
Fri May 29 15:18:19 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: -, status: running, sta_iface: -, sta_radio: -, sta_essid: -, sta_bssid: -, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:18:19 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: dev, name:  radio0, status: running, quality: 0, connection: -, wait: 1, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:18:19 2020 user.debug travelmate-1.2.2[440]: f_main ::: iwinfo: /usr/bin/iwinfo, dev_list:  radio0, sta_list:  cfg033579_radio0, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:18:20 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 90,88:90:8D:43:E9:A0,unknown,87,88:90:8D:43:E9:A3,"MyWifiSSID",85,88:90:8D:43:E9:A2,unknown,70,34:97:F6:08:FB:02,"5291",62,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",, cnt: 1, max_cnt: 3
Fri May 29 15:18:27 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 90,88:90:8D:43:E9:A3,"MyWifiSSID",85,88:90:8D:43:E9:A0,unknown,84,88:90:8D:43:E9:A2,unknown,62,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",60,34:97:F6:08:FB:02,"5291",52,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",45,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",, cnt: 2, max_cnt: 3
Fri May 29 15:18:34 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 88,88:90:8D:43:E9:A2,unknown,87,88:90:8D:43:E9:A3,"MyWifiSSID",87,88:90:8D:43:E9:A0,unknown,64,34:97:F6:08:FB:02,"5291",60,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",52,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",45,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",44,3A:22:E2:94:43:BD,"DIRECT-BD-HP OfficeJet Pro 8020",, cnt: 3, max_cnt: 3
Fri May 29 15:19:39 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: -, status: not connected, sta_iface: -, sta_radio: -, sta_essid: -, sta_bssid: -, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:19:39 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: initial, name: -, status: false, quality: 0, connection: -, wait: 1, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:19:39 2020 user.debug travelmate-1.2.2[440]: f_prep ::: config: cfg023579, mode: ap, network: lan, eap_rc: 0, radio: radio0, trm_radio: -, disabled:
Fri May 29 15:19:39 2020 user.debug travelmate-1.2.2[440]: f_prep ::: config: cfg033579, mode: sta, network: trm_wwan, eap_rc: 0, radio: radio0, trm_radio: -, disabled: 1
Fri May 29 15:19:39 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: -, status: running, sta_iface: -, sta_radio: -, sta_essid: -, sta_bssid: -, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:19:39 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: dev, name:  radio0, status: running, quality: 0, connection: -, wait: 1, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:19:39 2020 user.debug travelmate-1.2.2[440]: f_main ::: iwinfo: /usr/bin/iwinfo, dev_list:  radio0, sta_list:  cfg033579_radio0, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:19:41 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 90,88:90:8D:43:E9:A2,unknown,88,88:90:8D:43:E9:A3,"MyWifiSSID",87,88:90:8D:43:E9:A0,unknown,68,34:97:F6:08:FB:02,"5291",62,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",48,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",, cnt: 1, max_cnt: 3
Fri May 29 15:19:48 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 88,88:90:8D:43:E9:A3,"MyWifiSSID",88,88:90:8D:43:E9:A0,unknown,87,88:90:8D:43:E9:A2,unknown,71,34:97:F6:08:FB:02,"5291",62,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",48,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",, cnt: 2, max_cnt: 3
Fri May 29 15:19:55 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 87,88:90:8D:43:E9:A3,"MyWifiSSID",87,88:90:8D:43:E9:A2,unknown,87,88:90:8D:43:E9:A0,unknown,74,34:97:F6:08:FB:02,"5291",61,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",54,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",41,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",, cnt: 3, max_cnt: 3
Fri May 29 15:21:00 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: -, status: not connected, sta_iface: -, sta_radio: -, sta_essid: -, sta_bssid: -, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:21:00 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: initial, name: -, status: false, quality: 0, connection: -, wait: 1, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:21:00 2020 user.debug travelmate-1.2.2[440]: f_prep ::: config: cfg023579, mode: ap, network: lan, eap_rc: 0, radio: radio0, trm_radio: -, disabled:
Fri May 29 15:21:00 2020 user.debug travelmate-1.2.2[440]: f_prep ::: config: cfg033579, mode: sta, network: trm_wwan, eap_rc: 0, radio: radio0, trm_radio: -, disabled: 1
Fri May 29 15:21:00 2020 user.debug travelmate-1.2.2[440]: f_jsnup::: config: -, status: running, sta_iface: -, sta_radio: -, sta_essid: -, sta_bssid: -, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:21:00 2020 user.debug travelmate-1.2.2[440]: f_check::: mode: dev, name:  radio0, status: running, quality: 0, connection: -, wait: 1, max_wait: 30, min_quality: 35, captive: 1
Fri May 29 15:21:00 2020 user.debug travelmate-1.2.2[440]: f_main ::: iwinfo: /usr/bin/iwinfo, dev_list:  radio0, sta_list:  cfg033579_radio0, faulty_list:  radio0/MyWifiSSID/88:90:8D:43:E9:A3
Fri May 29 15:21:02 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 87,88:90:8D:43:E9:A3,"MyWifiSSID",87,88:90:8D:43:E9:A2,unknown,85,88:90:8D:43:E9:A0,unknown,68,34:97:F6:08:FB:02,"5291",61,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",52,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",42,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",, cnt: 1, max_cnt: 3
Fri May 29 15:21:09 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 88,88:90:8D:43:E9:A3,"MyWifiSSID",87,88:90:8D:43:E9:A2,unknown,85,88:90:8D:43:E9:A0,unknown,65,34:97:F6:08:FB:02,"5291",60,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",50,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",44,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",, cnt: 2, max_cnt: 3
Fri May 29 15:21:16 2020 user.debug travelmate-1.2.2[440]: f_main ::: dev: radio0, scan_list: 85,88:90:8D:43:E9:A3,"MyWifiSSID",85,88:90:8D:43:E9:A2,unknown,85,88:90:8D:43:E9:A0,unknown,62,34:97:F6:08:FB:02,"5291",58,D6:6A:6A:8E:1E:8C,"DIRECT-8c-HP M227f LaserJet",50,9E:93:4E:3A:35:4C,"DIRECT-BEPhaser 3260",42,7C:DB:98:0E:4A:79,"MySpectrumWiFi7b-2G",, cnt: 3, max_cnt: 3

jaylthegreat · May 29, 2020, 4:31pm

here is the iw list output.

root@OpenWrt:~# iw list
Wiphy phy0
        max # scan SSIDs: 10
        max scan IEs length: 2048 bytes
        max # sched scan SSIDs: 16
        max # match sets: 16
        max # scan plans: 1
        max scan plan interval: 508
        max scan plan iterations: 0
        Retry short limit: 7
        Retry long limit: 4
        Coverage class: 0 (up to 0m)
        Device supports T-DLS.
        Available Antennas: TX 0 RX 0
        Supported interface modes:
                 * IBSS
                 * managed
                 * AP
                 * P2P-client
                 * P2P-GO
                 * P2P-device
        Band 1:
                Capabilities: 0x1020
                        HT20
                        Static SM Power Save
                        RX HT20 SGI
                        No RX STBC
                        Max AMSDU length: 3839 bytes
                        DSSS/CCK HT40
                Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
                Minimum RX AMPDU time spacing: 16 usec (0x07)
                HT TX/RX MCS rate indexes supported: 0-7
                Frequencies:
                        * 2412 MHz [1] (20.0 dBm)
                        * 2417 MHz [2] (20.0 dBm)
                        * 2422 MHz [3] (20.0 dBm)
                        * 2427 MHz [4] (20.0 dBm)
                        * 2432 MHz [5] (20.0 dBm)
                        * 2437 MHz [6] (20.0 dBm)
                        * 2442 MHz [7] (20.0 dBm)
                        * 2447 MHz [8] (20.0 dBm)
                        * 2452 MHz [9] (20.0 dBm)
                        * 2457 MHz [10] (20.0 dBm)
                        * 2462 MHz [11] (20.0 dBm)
                        * 2467 MHz [12] (disabled)
                        * 2472 MHz [13] (disabled)
                        * 2484 MHz [14] (disabled)
        valid interface combinations:
                 * #{ managed } <= 1, #{ P2P-device } <= 1, #{ P2P-client, P2P-GO } <= 1,
                   total <= 3, #channels <= 2
                 * #{ managed } <= 1, #{ AP } <= 1, #{ P2P-client } <= 1, #{ P2P-device } <= 1,
                   total <= 4, #channels <= 1

trendy · May 29, 2020, 7:48pm

You can have only one station and one access point on the same channel.
So instead of configuring the trm_wwan , you can continue the configuration using the existing connection from step 4.

jaylthegreat · May 29, 2020, 8:37pm

Sorry if i misunderstand, but this is what i tried.

set it up as a wifi client as in step 4. (this replaces the default network that I was connected to) and installed the travelmate stuff

then when configuring travelmate i told it to use wwan instead of trm_wwan. After starting travelmate, the pi was still connected to internet, which is good.

However, now I must add the access point. I did this by modifying /etc/config/wireless.

Again I ran into the problem of wlan0 and/or wlan0-1 cycling through blocking, forwarding, and disabled states

markbirss · May 29, 2020, 9:48pm

Here is a tutorial for Rasbian Stretch

It seems like Openwrt not allow simulations ap and sta ?

Other approaches that i tried is allowing bluetooth clients to to get internet via Raspberry Pi connected wifi, but i needed to statically set a internet dns on my Android phone, also performance was not great

Other options adding another Wifi dongle or using the OTG usb port

jaylthegreat · May 29, 2020, 11:32pm

Yeah, I've managed to get it working with raspbian buster lite as well, but my conundrum is that I want the nice web interface since this will be used by people who are not necessarily tech savvy.

Sadly dongle is not an option. I was planning on using the micro usb for an ethernet connection; however, that seems to also have issues with versions past 17, as is described in this post

still, thank you for your response

markbirss · May 30, 2020, 11:42am

are you saying you cant get Ethernet Gadget working at all ?

trendy · May 30, 2020, 1:14pm

Alright. First thing I would do is to upgrade to the latest 19.07.3, since travelmate is tested by developer with 19.07 and snapshots, and install travelmate immediately, then configure it with as much default configuration as possible.
Other than that you can post here the runtime info /etc/init.d/travelmate status , enable debug and check logs logread -e "travelmate"

markbirss · May 30, 2020, 3:02pm

Im runing Snapshot and using OTG USB Ethernet Gadget mode

root@OpenWrt:~#  /etc/init.d/travelmate status
::: travelmate runtime information
  + travelmate_status  : connected (net ok/100)
  + travelmate_version : 1.5.4
  + station_id         : radio0/TP-LINK_7F83DE/-
  + station_interface  : trm_wwan lan
  + faulty_stations    : 
  + wpa_capabilities   : -/-/-
  + last_rundate       : 2020.05.30-17:00:07
  + system             : Raspberry Pi Zero W Rev 1.1, OpenWrt SNAPSHOT r13373-e8fbb98c6d

trendy · May 30, 2020, 3:39pm

Is the lan correct here?

markbirss · May 30, 2020, 4:06pm

that is what it reports ?

br-lan    Link encap:Ethernet  HWaddr 3E:82:09:68:C1:A1  
          inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::3c82:9ff:fe68:c1a1/64 Scope:Link
          inet6 addr: fd80:899e:51ca::1/60 Scope:Global
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:2245543 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3224420 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:839984379 (801.0 MiB)  TX bytes:4248224386 (3.9 GiB)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:1950 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1950 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:278250 (271.7 KiB)  TX bytes:278250 (271.7 KiB)

usb0      Link encap:Ethernet  HWaddr 3E:82:09:68:C1:A1  
          inet addr:10.1.1.1  Bcast:10.1.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:2245668 errors:0 dropped:123 overruns:0 frame:0
          TX packets:3227400 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:840169287 (801.2 MiB)  TX bytes:4248352526 (3.9 GiB)

wlan0     Link encap:Ethernet  HWaddr B8:27:EB:D0:65:41  
          inet addr:172.16.0.125  Bcast:172.16.0.255  Mask:255.255.255.0
          inet6 addr: fe80::ba27:ebff:fed0:6541/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:2873117 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1390358 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:4158280495 (3.8 GiB)  TX bytes:134509345 (128.2 MiB)

trendy · May 30, 2020, 4:41pm

I don't think lan interface is in station mode. Anyway, let's not hijack this thread.