travelmate does not seem to be working out about the same as just adding the network.
I'll describe what I've been doing and maybe you can tell me something is wrong.
- flash image onto sd card
- enable radio and restart the wifi
- connect through web interface
- go to wireless tab, scan, and connect to internet
- update opkg, install travelmate and luci-app-travelmate.
this is where I've tried a few different things, all having the same results
first I try to just use web interface to set it up, so I create the trm_wwan and then add the uplink
next I tried setting the pi back to just being an AP before setting up travelmate through the web interface.
Finally i tried just setting it up manually following instructions from the readme
Each time I would get similar logs. These are just from my last attempt with the manual configuration
dmesg
root@OpenWrt:~# cat dmesg.log
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.214 (buildbot@5b5c16a55686) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7989-82fbd85747) ) #0 Thu Feb 27 21:25:59 2020
[ 0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] OF: fdt:Machine model: Raspberry Pi Zero W Rev 1.1
[ 0.000000] cma: Reserved 16 MiB at 0x1ac00000
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] On node 0 totalpages: 114688
[ 0.000000] free_area_init_node: node 0, pgdat c0512000, node_mem_map dbc6a700
[ 0.000000] Normal zone: 896 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 114688 pages, LIFO batch:31
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 113792
[ 0.000000] Kernel command line: 8250.nr_uarts=1 bcm2708_fb.fbwidth=1824 bcm2708_fb.fbheight=984 bcm2708_fb.fbswap=1 smsc95xx.macaddr=B8:27:EB:B6:0C:BA vc_mem.mem_base=0x1ec00000 vc_mem.mem_size=0x20000000 dwc_otg.lpm_enable=0 console=ttyS0,115200 kgdboc=ttyS0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=squashfs,ext4 rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 432668K/458752K available (4000K kernel code, 153K rwdata, 716K rodata, 160K init, 353K bss, 9700K reserved, 16384K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xdc800000 - 0xff800000 ( 560 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdc000000 ( 448 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc03f0310 (4001 kB)
[ 0.000000] .init : 0xc04c4000 - 0xc04ec000 ( 160 kB)
[ 0.000000] .data : 0xc04ec000 - 0xc05127e0 ( 154 kB)
[ 0.000000] .bss : 0xc05127e0 - 0xc056ae70 ( 354 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000027] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns
[ 0.000076] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns
[ 0.000159] bcm2835: system timer (irq = 27)
[ 0.000640] Console: colour dummy device 80x30
[ 0.001380] console [tty1] enabled
[ 0.001443] Calibrating delay loop... 697.95 BogoMIPS (lpj=3489792)
[ 0.060312] pid_max: default: 32768 minimum: 301
[ 0.060497] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.060557] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.061365] CPU: Testing write buffer coherency: ok
[ 0.061785] Setting up static identity map for 0x8200 - 0x825c
[ 0.071149] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
[ 0.071640] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.071743] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.073945] pinctrl core: initialized pinctrl subsystem
[ 0.075526] NET: Registered protocol family 16
[ 0.077899] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 0.086867] cpuidle: using governor ladder
[ 0.086955] cpuidle: using governor menu
[ 0.087479] Serial: AMBA PL011 UART driver
[ 0.091949] bcm2835-mbox 2000b880.mailbox: mailbox enabled
[ 0.092672] uart-pl011 20201000.serial: could not find pctldev for node /soc/gpio@7e200000/uart0_pins, deferring probe
[ 0.134534] bcm2835-dma 20007000.dma: DMA legacy API manager at dc811000, dmachans=0x1
[ 0.137701] SCSI subsystem initialized
[ 0.138013] usbcore: registered new interface driver usbfs
[ 0.138167] usbcore: registered new interface driver hub
[ 0.138312] usbcore: registered new device driver usb
[ 0.140676] raspberrypi-firmware soc:firmware: Attached to firmware from 2018-11-23 19:36
[ 0.142291] clocksource: Switched to clocksource timer
[ 0.153498] NET: Registered protocol family 2
[ 0.154593] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.154734] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.154845] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.154967] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.155034] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.155315] NET: Registered protocol family 1
[ 0.156826] Crashlog allocated RAM at address 0x3f00000
[ 0.157290] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 0.167673] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.169865] io scheduler noop registered
[ 0.169941] io scheduler deadline registered
[ 0.170276] io scheduler cfq registered (default)
[ 0.176271] BCM2708FB: allocated DMA memory 5ad00000
[ 0.176378] BCM2708FB: allocated DMA channel 0 @ dc811000
[ 0.223953] Console: switching to colour frame buffer device 228x61
[ 0.261311] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled
[ 0.263002] console [ttyS0] disabled
[ 0.263255] 20215040.serial: ttyS0 at MMIO 0x0 (irq = 53, base_baud = 31250000) is a 16550
[ 0.736121] console [ttyS0] enabled
[ 0.741003] vc-cma: Videocore CMA driver
[ 0.745247] vc-cma: vc_cma_base = 0x00000000
[ 0.750216] vc-cma: vc_cma_size = 0x00000000 (0 MiB)
[ 0.755941] vc-cma: vc_cma_initial = 0x00000000 (0 MiB)
[ 0.761910] vc-mem: phys_addr:0x00000000 mem_base=0x1ec00000 mem_size:0x20000000(512 MiB)
[ 0.790215] brd: module loaded
[ 0.803635] loop: module loaded
[ 0.807314] usbcore: registered new interface driver smsc95xx
[ 0.813487] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 1.047668] Core Release: 2.80a
[ 1.051023] Setting default values for core params
[ 1.056180] Finished setting default values for core params
[ 1.262353] Using Buffer DMA mode
[ 1.265884] Periodic Transfer Interrupt Enhancement - disabled
[ 1.272024] Multiprocessor Interrupt Enhancement - disabled
[ 1.277940] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 1.282581] Dedicated Tx FIFOs mode
[ 1.286886] WARN::dwc_otg_hcd_init:1053: FIQ DMA bounce buffers: virt = 0xdad14000 dma = 0x5ad14000 len=9024
[ 1.297291] FIQ FSM acceleration enabled for :
[ 1.297291] Non-periodic Split Transactions
[ 1.297291] Periodic Split Transactions
[ 1.297291] High-Speed Isochronous Endpoints
[ 1.297291] Interrupt/Control Split Transaction hack enabled
[ 1.339321] dwc_otg: Microframe scheduler enabled
[ 1.339495] WARN::hcd_init_fiq:459: FIQ on core 0 at 0xc02a4d44
[ 1.355213] WARN::hcd_init_fiq:460: FIQ ASM at 0xc02a4fc4 length 36
[ 1.371131] WARN::hcd_init_fiq:486: MPHI regs_base at 0xdc8c1000
[ 1.386829] dwc_otg 20980000.usb: DWC OTG Controller
[ 1.401270] dwc_otg 20980000.usb: new USB bus registered, assigned bus number 1
[ 1.417905] dwc_otg 20980000.usb: irq 56, io mem 0x00000000
[ 1.432714] Init: Port Power? op_state=1
[ 1.445744] Init: Power Port (0)
[ 1.458437] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.475010] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.491914] usb usb1: Product: DWC OTG Controller
[ 1.506132] usb usb1: Manufacturer: Linux 4.9.214 dwc_otg_hcd
[ 1.521418] usb usb1: SerialNumber: 20980000.usb
[ 1.536421] hub 1-0:1.0: USB hub found
[ 1.549555] hub 1-0:1.0: 1 port detected
[ 1.563386] dwc_otg: FIQ enabled
[ 1.563394] dwc_otg: NAK holdoff enabled
[ 1.563401] dwc_otg: FIQ split-transaction FSM enabled
[ 1.563422] Module dwc_common_port init
[ 1.563808] usbcore: registered new interface driver uas
[ 1.578519] usbcore: registered new interface driver usb-storage
[ 1.593797] mousedev: PS/2 mouse device common for all mice
[ 1.609896] bcm2835-wdt 20100000.watchdog: Broadcom BCM2835 watchdog timer
[ 1.626741] bcm2835-cpufreq: min=700000 max=1000000
[ 1.641659] sdhci: Secure Digital Host Controller Interface driver
[ 1.657245] sdhci: Copyright(c) Pierre Ossman
[ 1.671731] sdhost: log_buf @ dad13000 (5ad13000)
[ 1.762357] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[ 1.777142] mmc-bcm2835 20300000.mmc: mmc_debug:0 mmc_debug2:0
[ 1.789788] mmc-bcm2835 20300000.mmc: DMA channel allocated
[ 1.823234] Indeed it is in host mode hprt0 = 00041901
[ 1.901069] random: fast init done
[ 1.922478] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.937749] vchiq: vchiq_init_state: slot_zero = 0xdad80000, is_master = 0
[ 1.960966] NET: Registered protocol family 10
[ 1.975947] NET: Registered protocol family 17
[ 1.987182] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.007143] 8021q: 802.1Q VLAN Support v1.8
[ 2.021976] vc-sm: Videocore shared memory driver
[ 2.033867] [vc_sm_connected_init]: start
[ 2.044755] usb 1-1: new low-speed USB device number 2 using dwc_otg
[ 2.059532] Indeed it is in host mode hprt0 = 00041901
[ 2.132506] [vc_sm_connected_init]: end - returning 0
[ 2.147695] 20201000.serial: ttyAMA0 at MMIO 0x20201000 (irq = 81, base_baud = 0) is a PL011 rev2
[ 2.164389] of_cfs_init
[ 2.173823] of_cfs_init: OK
[ 2.184525] mmc0: host does not support reading read-only switch, assuming write-enable
[ 2.200228] Waiting for root device /dev/mmcblk0p2...
[ 2.213366] mmc0: new high speed SDHC card at address 0001
[ 2.226959] mmcblk0: mmc0:0001 00000 29.1 GiB
[ 2.240858] mmcblk0: p1 p2
[ 2.254101] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[ 2.268489] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 2.282443] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 2.297499] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[ 2.328966] usb 1-1: New USB device found, idVendor=413c, idProduct=2003
[ 2.342606] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.356635] usb 1-1: Product: Dell USB Keyboard
[ 2.367976] usb 1-1: Manufacturer: Dell
[ 2.453491] mmc1: new high speed SDIO card at address 0001
[ 2.503602] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null)
[ 2.518226] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 2.532331] Freeing unused kernel memory: 160K
[ 2.543444] This architecture does not have kernel memory protection.
[ 2.626487] init: Console is alive
[ 2.637381] init: - watchdog -
[ 2.805884] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.828494] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 2.856227] init: - preinit -
[ 3.160886] random: jshn: uninitialized urandom read (4 bytes read)
[ 3.218303] random: jshn: uninitialized urandom read (4 bytes read)
[ 3.263681] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.493831] mount_root: mounting /dev/root
[ 6.510234] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 6.614224] urandom-seed: Seeding with /etc/urandom.seed
[ 6.676747] procd: - early -
[ 6.689823] procd: - watchdog -
[ 7.353549] procd: - watchdog -
[ 7.364300] procd: - ubus -
[ 7.392633] urandom_read: 1 callbacks suppressed
[ 7.392645] random: ubusd: uninitialized urandom read (4 bytes read)
[ 7.429995] random: ubusd: uninitialized urandom read (4 bytes read)
[ 7.446591] random: ubusd: uninitialized urandom read (4 bytes read)
[ 7.464230] procd: - init -
[ 7.756455] kmodloader: loading kernel modules from /etc/modules.d/*
[ 7.805984] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.834045] hidraw: raw HID events driver (C) Jiri Kosina
[ 7.877909] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[ 7.893098] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 7.910883] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.931328] nf_conntrack version 0.5.0 (7168 buckets, 28672 max)
[ 7.988136] input: Dell Dell USB Keyboard as /devices/platform/soc/20980000.usb/usb1/1-1/1-1:1.0/0003:413C:2003.0001/input/input0
[ 8.072895] hid-generic 0003:413C:2003.0001: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-20980000.usb-1/input0
[ 8.092860] usbcore: registered new interface driver usbhid
[ 8.105633] usbhid: USB HID core driver
[ 8.133362] xt_time: kernel timezone is -0000
[ 8.169338] PPP generic driver version 2.4.2
[ 8.182979] NET: Registered protocol family 24
[ 8.210547] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430-sdio for chip BCM43430/1
[ 8.246561] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43430-sdio.raspberrypi,model-zero-w.txt failed with error -2
[ 8.265825] brcmfmac mmc1:0001:1: Falling back to user helper
[ 8.296806] firmware brcm!brcmfmac43430-sdio.raspberrypi,model-zero-w.txt: firmware_loading_store: map pages failed
[ 8.404911] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430-sdio for chip BCM43430/1
[ 8.421484] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43430-sdio.clm_blob failed with error -2
[ 8.439429] brcmfmac mmc1:0001:1: Falling back to user helper
[ 8.469603] firmware brcm!brcmfmac43430-sdio.clm_blob: firmware_loading_store: map pages failed
[ 8.486567] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-11), device may have limited channels available
[ 8.511427] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43430/1 wl0: Aug 29 2016 20:48:16 version 7.45.41.26 (r640327) FWID 01-4527cfab
[ 8.569828] usbcore: registered new interface driver brcmfmac
[ 8.600724] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 15.974789] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 18.532284] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 18.595965] br-lan: port 1(wlan0) entered blocking state
[ 18.609456] br-lan: port 1(wlan0) entered disabled state
[ 18.623420] device wlan0 entered promiscuous mode
[ 18.863440] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 18.878121] br-lan: port 1(wlan0) entered blocking state
[ 18.891527] br-lan: port 1(wlan0) entered forwarding state
[ 19.081215] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 20.135415] random: crng init done
[ 20.146584] random: 3 urandom warning(s) missed due to ratelimiting
[ 22.322601] device wlan0 left promiscuous mode
[ 22.335468] br-lan: port 1(wlan0) entered disabled state
[ 23.455020] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 24.923390] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
[ 24.966059] br-lan: port 1(wlan0-1) entered blocking state
[ 24.977819] br-lan: port 1(wlan0-1) entered disabled state
[ 24.990176] device wlan0-1 entered promiscuous mode
[ 25.001595] br-lan: port 1(wlan0-1) entered blocking state
[ 25.013113] br-lan: port 1(wlan0-1) entered forwarding state
[ 25.028133] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 25.242075] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 25.412414] br-lan: port 1(wlan0-1) entered disabled state
[ 26.214035] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 26.380389] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[ 26.396001] br-lan: port 1(wlan0-1) entered blocking state
[ 26.409999] br-lan: port 1(wlan0-1) entered forwarding state
[ 26.910691] br-lan: port 1(wlan0-1) entered disabled state
[ 27.668365] br-lan: port 1(wlan0-1) entered blocking state
[ 27.679784] br-lan: port 1(wlan0-1) entered forwarding state
[ 28.171804] br-lan: port 1(wlan0-1) entered disabled state
[ 28.890917] br-lan: port 1(wlan0-1) entered blocking state
[ 28.902645] br-lan: port 1(wlan0-1) entered forwarding state
[ 29.382431] br-lan: port 1(wlan0-1) entered disabled state
[ 30.121544] br-lan: port 1(wlan0-1) entered blocking state
[ 30.133241] br-lan: port 1(wlan0-1) entered forwarding state
[ 30.615616] br-lan: port 1(wlan0-1) entered disabled state
[ 31.222928] br-lan: port 1(wlan0-1) entered blocking state
[ 31.234493] br-lan: port 1(wlan0-1) entered forwarding state
[ 41.575762] br-lan: port 1(wlan0-1) entered disabled state
[ 43.340166] br-lan: port 1(wlan0-1) entered blocking state
[ 43.353790] br-lan: port 1(wlan0-1) entered forwarding state
[ 54.048000] br-lan: port 1(wlan0-1) entered disabled state
[ 54.298297] br-lan: port 1(wlan0-1) entered blocking state
[ 54.311535] br-lan: port 1(wlan0-1) entered forwarding state
[ 55.123449] br-lan: port 1(wlan0-1) entered disabled state
[ 55.457975] br-lan: port 1(wlan0-1) entered blocking state
[ 55.471562] br-lan: port 1(wlan0-1) entered forwarding state
[ 56.164535] br-lan: port 1(wlan0-1) entered disabled state
[ 56.681564] ieee80211 phy0: brcmf_cfg80211_start_ap: SET SSID error (-512)
[ 56.694377] ieee80211 phy0: brcmf_set_mpc: fail to set mpc
[ 56.744668] device wlan0-1 left promiscuous mode
[ 56.755505] br-lan: port 1(wlan0-1) entered disabled state
[ 67.346580] ieee80211 phy0: brcmf_cfg80211_get_channel: chanspec failed (-52)
[ 67.424240] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 68.482556] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 68.527161] br-lan: port 1(wlan0) entered blocking state
[ 68.539101] br-lan: port 1(wlan0) entered disabled state
[ 68.551455] device wlan0 entered promiscuous mode
[ 68.666187] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 68.679150] br-lan: port 1(wlan0) entered blocking state
[ 68.690897] br-lan: port 1(wlan0) entered forwarding state
[ 68.794735] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 73.276306] device wlan0 left promiscuous mode
[ 73.287408] br-lan: port 1(wlan0) entered disabled state
[ 75.170620] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
[ 75.230606] br-lan: port 1(wlan0-1) entered blocking state
[ 75.242715] br-lan: port 1(wlan0-1) entered disabled state
[ 75.255474] device wlan0-1 entered promiscuous mode
[ 75.267271] br-lan: port 1(wlan0-1) entered blocking state
[ 75.279162] br-lan: port 1(wlan0-1) entered forwarding state
[ 75.313089] br-lan: port 1(wlan0-1) entered disabled state
[ 75.502882] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 77.125319] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 77.291083] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[ 77.304557] br-lan: port 1(wlan0-1) entered blocking state
[ 77.316642] br-lan: port 1(wlan0-1) entered forwarding state
[ 77.805325] br-lan: port 1(wlan0-1) entered disabled state
[ 78.567598] br-lan: port 1(wlan0-1) entered blocking state
[ 78.581849] br-lan: port 1(wlan0-1) entered forwarding state
[ 79.077400] br-lan: port 1(wlan0-1) entered disabled state
[ 79.787971] br-lan: port 1(wlan0-1) entered blocking state
[ 79.799867] br-lan: port 1(wlan0-1) entered forwarding state
[ 80.286374] br-lan: port 1(wlan0-1) entered disabled state
[ 81.013168] br-lan: port 1(wlan0-1) entered blocking state
[ 81.026797] br-lan: port 1(wlan0-1) entered forwarding state
[ 82.840366] br-lan: port 1(wlan0-1) entered disabled state
[ 83.061246] br-lan: port 1(wlan0-1) entered blocking state
[ 83.074891] br-lan: port 1(wlan0-1) entered forwarding state
[ 83.843394] br-lan: port 1(wlan0-1) entered disabled state
[ 84.293652] br-lan: port 1(wlan0-1) entered blocking state
[ 84.304984] br-lan: port 1(wlan0-1) entered forwarding state
[ 84.861148] br-lan: port 1(wlan0-1) entered disabled state
[ 85.518111] br-lan: port 1(wlan0-1) entered blocking state
[ 85.528922] br-lan: port 1(wlan0-1) entered forwarding state
[ 86.015549] br-lan: port 1(wlan0-1) entered disabled state
[ 86.747525] br-lan: port 1(wlan0-1) entered blocking state
[ 86.760152] br-lan: port 1(wlan0-1) entered forwarding state
[ 87.244860] br-lan: port 1(wlan0-1) entered disabled state
[ 87.723679] br-lan: port 1(wlan0-1) entered blocking state
[ 87.734543] br-lan: port 1(wlan0-1) entered forwarding state
[ 97.762338] ieee80211 phy0: brcmf_escan_timeout: timer expired
[ 98.239574] br-lan: port 1(wlan0-1) entered disabled state
[ 98.527925] br-lan: port 1(wlan0-1) entered blocking state
[ 98.540735] br-lan: port 1(wlan0-1) entered forwarding state
[ 99.283413] br-lan: port 1(wlan0-1) entered disabled state
[ 99.757218] br-lan: port 1(wlan0-1) entered blocking state
[ 99.769847] br-lan: port 1(wlan0-1) entered forwarding state
[ 100.293349] br-lan: port 1(wlan0-1) entered disabled state
[ 100.993662] br-lan: port 1(wlan0-1) entered blocking state
[ 101.004262] br-lan: port 1(wlan0-1) entered forwarding state
[ 101.481951] br-lan: port 1(wlan0-1) entered disabled state
[ 105.972377] br-lan: port 1(wlan0-1) entered blocking state
[ 105.984714] br-lan: port 1(wlan0-1) entered forwarding state
[ 109.052709] br-lan: port 1(wlan0-1) entered disabled state
[ 109.068537] device wlan0-1 left promiscuous mode
[ 109.077912] br-lan: port 1(wlan0-1) entered disabled state
[ 110.215900] ieee80211 phy0: brcmf_cfg80211_get_channel: chanspec failed (-52)
[ 110.304137] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 111.510936] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 111.545995] br-lan: port 1(wlan0) entered blocking state
[ 111.556411] br-lan: port 1(wlan0) entered disabled state
[ 111.567135] device wlan0 entered promiscuous mode
[ 111.846828] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 111.858542] br-lan: port 1(wlan0) entered blocking state
[ 111.868875] br-lan: port 1(wlan0) entered forwarding state
[ 111.988648] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 125.449821] device wlan0 left promiscuous mode
[ 125.459268] br-lan: port 1(wlan0) entered disabled state
[ 127.315727] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
[ 127.366242] br-lan: port 1(wlan0-1) entered blocking state
[ 127.376560] br-lan: port 1(wlan0-1) entered disabled state
[ 127.387359] device wlan0-1 entered promiscuous mode
[ 127.397398] br-lan: port 1(wlan0-1) entered blocking state
[ 127.407937] br-lan: port 1(wlan0-1) entered forwarding state
[ 127.482447] br-lan: port 1(wlan0-1) entered disabled state
[ 127.649890] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 128.635417] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 128.794295] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[ 128.806428] br-lan: port 1(wlan0-1) entered blocking state
[ 128.817193] br-lan: port 1(wlan0-1) entered forwarding state
[ 129.573257] br-lan: port 1(wlan0-1) entered disabled state
[ 130.069966] br-lan: port 1(wlan0-1) entered blocking state
[ 130.082595] br-lan: port 1(wlan0-1) entered forwarding state
[ 130.583479] br-lan: port 1(wlan0-1) entered disabled state
[ 131.304679] br-lan: port 1(wlan0-1) entered blocking state
[ 131.315530] br-lan: port 1(wlan0-1) entered forwarding state
[ 131.795692] br-lan: port 1(wlan0-1) entered disabled state
[ 132.524105] br-lan: port 1(wlan0-1) entered blocking state
[ 132.536933] br-lan: port 1(wlan0-1) entered forwarding state
[ 133.024201] br-lan: port 1(wlan0-1) entered disabled state
[ 133.626952] br-lan: port 1(wlan0-1) entered blocking state
[ 133.637790] br-lan: port 1(wlan0-1) entered forwarding state
[ 134.123620] br-lan: port 1(wlan0-1) entered disabled state
[ 134.402217] br-lan: port 1(wlan0-1) entered blocking state
[ 134.414720] br-lan: port 1(wlan0-1) entered forwarding state
[ 135.203280] br-lan: port 1(wlan0-1) entered disabled state
[ 135.591184] br-lan: port 1(wlan0-1) entered blocking state
[ 135.603794] br-lan: port 1(wlan0-1) entered forwarding state
[ 136.228463] br-lan: port 1(wlan0-1) entered disabled state
[ 136.840020] br-lan: port 1(wlan0-1) entered blocking state
[ 136.850723] br-lan: port 1(wlan0-1) entered forwarding state
[ 137.333622] br-lan: port 1(wlan0-1) entered disabled state
[ 138.057298] br-lan: port 1(wlan0-1) entered blocking state
[ 138.069931] br-lan: port 1(wlan0-1) entered forwarding state
[ 138.553481] br-lan: port 1(wlan0-1) entered disabled state
[ 139.283311] br-lan: port 1(wlan0-1) entered blocking state
[ 139.293668] br-lan: port 1(wlan0-1) entered forwarding state
[ 141.067572] br-lan: port 1(wlan0-1) entered disabled state
[ 141.379381] br-lan: port 1(wlan0-1) entered blocking state
[ 141.390053] br-lan: port 1(wlan0-1) entered forwarding state
[ 142.083480] br-lan: port 1(wlan0-1) entered disabled state
[ 142.580017] br-lan: port 1(wlan0-1) entered blocking state
[ 142.592186] br-lan: port 1(wlan0-1) entered forwarding state
[ 143.093438] br-lan: port 1(wlan0-1) entered disabled state
[ 143.788911] br-lan: port 1(wlan0-1) entered blocking state
[ 143.799222] br-lan: port 1(wlan0-1) entered forwarding state
[ 144.286209] br-lan: port 1(wlan0-1) entered disabled state
[ 145.018064] br-lan: port 1(wlan0-1) entered blocking state
[ 145.029655] br-lan: port 1(wlan0-1) entered forwarding state
[ 145.519849] br-lan: port 1(wlan0-1) entered disabled state
[ 145.988105] br-lan: port 1(wlan0-1) entered blocking state
[ 145.998096] br-lan: port 1(wlan0-1) entered forwarding state
[ 156.002333] ieee80211 phy0: brcmf_escan_timeout: timer expired
[ 156.480784] br-lan: port 1(wlan0-1) entered disabled state
[ 157.687076] br-lan: port 1(wlan0-1) entered blocking state
[ 157.698380] br-lan: port 1(wlan0-1) entered forwarding state
[ 159.545115] br-lan: port 1(wlan0-1) entered disabled state
[ 162.323816] br-lan: port 1(wlan0-1) entered blocking state
[ 162.335088] br-lan: port 1(wlan0-1) entered forwarding state
[ 163.193245] br-lan: port 1(wlan0-1) entered disabled state
[ 163.312279] device wlan0-1 left promiscuous mode
[ 163.321282] br-lan: port 1(wlan0-1) entered disabled state
[ 164.484260] ieee80211 phy0: brcmf_cfg80211_get_channel: chanspec failed (-52)
[ 164.549856] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 165.813214] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 165.855748] br-lan: port 1(wlan0) entered blocking state
[ 165.865564] br-lan: port 1(wlan0) entered disabled state
[ 165.875688] device wlan0 entered promiscuous mode
[ 166.128989] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 166.140347] br-lan: port 1(wlan0) entered blocking state
[ 166.150245] br-lan: port 1(wlan0) entered forwarding state
[ 166.278468] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
I notice that it eventually puts my router on the faulty list. I know that i used the right password and everything.
if more details are needed. please let me know