Hello Everyone,
ZBT WE826 16m has inbuilt modem and a simcard slot.. I have built an image with modemmanager and luci-proto-modemmanager for the same but the modem does not get detected.. I tried using the mmcli command it shows nothing ... Please help
First confirm that you do have a modem card (as the base WE826 ships with an empty slot -- modem is sold separately) and what model it is. You'll need the kernel driver for the modem, which depends on what protocol type the modem uses. Most late model modems are either rndis or qmi.
rndis is very simple-- install kmod-usb-net-rndis and a new Ethernet like interface should be created. Attach it to the wan network.
qmi starts with kmod-usb-net-qmi-wwan but you should also install luci-proto-qmi to configure it.
1 Like
Depending upon the order, ZBT or one of their OEMs also ships the WE-826 incl. modem, which usually is region-specific, i.e. for USA or Europe. Quite often, it is a Quectel EC25, but sometimes also might be a SIMCOM, to save $5.
However, the Quectel EC25 definitely is the preferred modem, in case you do not need highest speed.
1 Like
mine is definitely with the modem as I did connect it to the internet with the sim card and AT commands with the default openwrt it came with which was LEDE so I built one myself with modemmanager etc and latest 19.07 but now it doesnot connect ... Its WE826 T2 ..
regarding the kernel driver for the modem could you tell me how do I know the type of modem.. This is the first time I am dealing with modem and openwrt so completely clueless here.
To be absolutely shure, just open the box. As you used it already, region matches, at least.
If you run dmesg after a reboot you should see some messages there indicating that the modem is ready for use. If you do not, then that means either your firmware is missing a required kernel module, or perhaps the modem is not powered on. Sometimes a modem is powered up via a GPIO pin, and you will have to toggle that GPIO. If it is a Quectel EC25 modem in NDIS mode, then you probably cannot use ModemManager to control the modem, you will need to use something like comgt, so try luci-proto-ncm.
The modem seems not initialised as I don't see such a message in the dmesg logs.. I am building another firmware with the AT commands lets see if I can get the modem detected with them.. Moreover the modem used is
Folksy 3RN13
Please share me information about it if you have any... regarding which kernel module would be required to get it detected automatically etc
Do you see a USB bus in the kernel logs? You may be missing USB, which would preclude anything attached to the USB bus from being detected. Try adding kmod-usb kmod-usb2 kmod-usb2-pci and kmod-usb3, then add kmod-usb-serial-qualcomm, as this looks like it has a Qualcomm chip based on what I found online.
How about you post your dmesg output after a full boot to Pastebin then link it here.
Start from posting the result of cat /sys/kernel/debug/usb/devices
That way we can probably make it properly detected by OpenWrt, however I read about 'No SIM' issue that has nothing to do with OpenWrt.
Getting a better modem should be the right choice.
My modem in a WG 3526 is also not detected, also with the above mentioned
kmod-usb-blablabla modules. Expect in the original chinese firmware (19.01.11),
but it never transferred any data thru 4/3/2G network. Weird!!
I think its some fault in the modem firmware as i tried a Asus 4G-AC68U which
uses, from my view, a good made firmware.
But it also not transferred any data. It seems this asian devices do
not work in specific regions.
I have got the chinese firmware which I extracted before I flashed the device with the latest openwrt.. I am thinking now of comparing the firmwares as with the chinese firmware I could make the modem work with the AT commands but there was some weird problem with dnsmasq and I was unable to install dnsmasq-full because it was running lede and the feeds links were all useless ones.. So I though of the upgrade... but anyways if anyone has any Idea please share.. Thanks 
Hello,
I am suffering the same issue with the Folksy modem.
Unfortunately I did not keep the original Firmware
Is there a way to get it ? I would like to work on finding the module on it
Thanks
You don't need original firmware to find the modem.
Thanks !
I did not get that far ... I did not insert the SIM as I believed that the card was not recognised
Here is the output of the cat /sys/kernel/debug/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 1, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 4.14
S: Manufacturer=Linux 4.14.167 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=101c0000.ehci
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256msT: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=05e3 ProdID=0608 Rev=85.36
S: Product=USB2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256msT: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bbb ProdID=0192 Rev= 2.32
S: Manufacturer=Alcatel
S: Product=MobileBroadBand
S: SerialNumber=0123456789ABCDEF
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=85(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 3 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=125usT: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 1
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0001 Rev= 4.14
S: Manufacturer=Linux 4.14.167 ohci_hcd
S: Product=Generic Platform OHCI controller
S: SerialNumber=101c1000.ohci
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
It seems to me that it is a "Alcatel Onetouch L850"
isn't it ?
Your modem is recognized and cdc_ether driver is bound to some interface. Just find the ethX interface name and configure it. See TP-Link Archer C7 v5 with TELSEC TS-1K6 USB 4G Modem
Thanks,
Indeed, I missed the relevant part on the output from "dmesg"
[ 21.028224] cdc_ether 1-1.3:1.2 eth1: register 'cdc_ether' at usb-101c0000.ehci-1.3, CDC Ethernet Device, 08:2e:5f:29:0e:69
[ 21.039982] usbcore: registered new interface drive[ 71.311531] cdc_ether 1-1.3:1.2 eth1: kevent 12 may have been dropped
[ 71.808994] cdc_ether 1-1.3:1.2 eth1: kevent 12 may have been dropped
[ 71.815680] cdc_ether 1-1.3:1.2 eth1: kevent 12 may have been dropped
[ 71.822273] cdc_ether 1-1.3:1.2 eth1: kevent 12 may have been dropped
[ 71.828879] cdc_ether 1-1.3:1.2 eth1: kevent 12 may have been dropped r cdc_ether
[ 21.072634] usbcore: registered new interface driver cdc_ncm
[ 21.144957] usbcore: registered new interface driver huawei_cdc_ncm
[ 21.314494] PPP generic driver version 2.4.2
[ 21.333097] NET: Registered protocol family 24
[ 21.351929] usbcore: registered new interface driver qmi_wwan
[ 21.370338] usbcore: registered new interface driver rndis_host
[ 21.431400] usbcore: registered new interface driver sierra
[ 21.437185] usbserial: USB Serial support registered for Sierra USB modem
[ 21.455442] usbcore: registered new interface driver sierra_net
[ 21.480952] usbcore: registered new interface driver cdc_mbim
[ 21.496146] usbcore: registered new interface driver option
[ 21.502054] usbserial: USB Serial support registered for GSM modem (1-port)
[ 21.539161] usbcore: registered new interface driver qcserial
[ 21.545126] usbserial: USB Serial support registered for Qualcomm USB modem
And later ...
[ 71.311531] cdc_ether 1-1.3:1.2 eth1: kevent 12 may have been dropped
[ 71.808994] cdc_ether 1-1.3:1.2 eth1: kevent 12 may have been dropped
[ 71.815680] cdc_ether 1-1.3:1.2 eth1: kevent 12 may have been dropped
[ 71.822273] cdc_ether 1-1.3:1.2 eth1: kevent 12 may have been dropped
[ 71.828879] cdc_ether 1-1.3:1.2 eth1: kevent 12 may have been dropped
the output of "ifconfig eth1" follows:
eth1 Link encap:Ethernet HWaddr 08:2E:5F:29:0E:69
inet addr:192.168.0.9 Bcast:192.168.3.255 Mask:255.255.252.0
inet6 addr: fe80::a2e:5fff:fe29:e69/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:197 errors:0 dropped:0 overruns:0 frame:0
TX packets:33 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:8636 (8.4 KiB) TX bytes:3445 (3.3 KiB)
I will check how to configure it.
I will come back with the result. Some others may benefit from my investigations
Thanks
Hi @AndrewZ the dmesg output doesnot have cdc_ether in mycase I am unable to detect the modem
0.000000] Linux version 4.14.195 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11208-ce6496d796)) #0 Sun Sep 6 16:19:39 2020
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is ZBT-WE826 (16M)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 8047e5d0, node_mem_map 81000040
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] random: get_random_bytes called from 0x80481740 with crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00002800
[ 0.000000] Readback ErrCtl register=00002800
[ 0.000000] Memory: 123780K/131072K available (3918K kernel code, 185K rwdata, 500K rodata, 1212K init, 215K bss, 7292K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000012] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.007608] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.073559] pid_max: default: 32768 minimum: 301
[ 0.078284] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.084669] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.097681] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.107229] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.113206] pinctrl core: initialized pinctrl subsystem
[ 0.119561] NET: Registered protocol family 16
[ 0.604319] mt7620-pci 10140000.pcie: PCIE0 no card, disable it(RST&CLK)
[ 0.610826] mt7620-pci: probe of 10140000.pcie failed with error -1
[ 0.634436] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.639833] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.646243] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.651615] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.657999] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.663291] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.674113] clocksource: Switched to clocksource systick
[ 0.680474] NET: Registered protocol family 2
[ 0.685667] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.692393] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.698623] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.704907] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.710535] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.716921] NET: Registered protocol family 1
[ 0.721111] PCI: CLS 0 bytes, default 32
[ 0.723846] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.730562] Crashlog allocated RAM at address 0x3f00000
[ 0.737371] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 0.749650] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.755304] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.775338] io scheduler noop registered
[ 0.779086] io scheduler deadline registered (default)
[ 0.785056] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.794019] console [ttyS0] disabled
[ 0.797538] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.807160] console [ttyS0] enabled
[ 0.814209] bootconsole [early0] disabled
[ 0.830199] spi spi0.0: force spi mode3
[ 0.843853] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.848768] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.855266] Creating 4 MTD partitions on "spi0.0":
[ 0.860167] 0x000000000000-0x000000030000 : "u-boot"
[ 0.866201] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.872476] 0x000000040000-0x000000050000 : "factory"
[ 0.878595] 0x000000050000-0x000001000000 : "firmware"
[ 0.887681] 2 uimage-fw partitions found on MTD device firmware
[ 0.893733] Creating 2 MTD partitions on "firmware":
[ 0.898875] 0x000000000000-0x00000017e418 : "kernel"
[ 0.904865] 0x00000017e418-0x000000fb0000 : "rootfs"
[ 0.910751] mtd: device 5 (rootfs) set to be root filesystem
[ 0.918158] 1 squashfs-split partitions found on MTD device rootfs
[ 0.924548] 0x0000003fd000-0x000000fb0000 : "rootfs_data"
[ 0.931792] libphy: Fixed MDIO Bus: probed
[ 0.944594] gsw: setting port4 to ephy mode
[ 0.948916] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 0 link up (100Mbps/Full duplex)
[ 0.958480] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 0.965265] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 0.974266] rt2880_wdt 10000120.watchdog: Initialized
[ 0.980800] NET: Registered protocol family 10
[ 0.989477] Segment Routing with IPv6
[ 0.993334] NET: Registered protocol family 17
[ 0.997997] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.011236] 8021q: 802.1Q VLAN Support v1.8
[ 1.033355] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 1.047364] Freeing unused kernel memory: 1212K
[ 1.051987] This architecture does not have kernel memory protection.
[ 2.664058] random: fast init done
[ 2.857543] init: Console is alive
[ 2.861285] init: - watchdog -
[ 4.996885] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.102511] usbcore: registered new interface driver usbfs
[ 5.108282] usbcore: registered new interface driver hub
[ 5.113819] usbcore: registered new device driver usb
[ 5.124904] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.133263] ehci-platform: EHCI generic platform driver
[ 5.149042] phy phy-usbphy.0: remote usb device wakeup disabled
[ 5.155105] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 5.159657] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 5.165573] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 5.173765] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 5.188475] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 5.195889] hub 1-0:1.0: USB hub found
[ 5.200183] hub 1-0:1.0: 1 port detected
[ 5.207480] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.215412] ohci-platform: OHCI generic platform driver
[ 5.221110] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 5.228068] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 5.236311] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 5.270197] hub 2-0:1.0: USB hub found
[ 5.274428] hub 2-0:1.0: 1 port detected
[ 5.314685] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.326252] init: - preinit -
[ 6.284713] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 6.635370] hub 1-1:1.0: USB hub found
[ 6.640833] random: procd: uninitialized urandom read (4 bytes read)
[ 6.647659] hub 1-1:1.0: 4 ports detected
[ 7.197025] 8021q: adding VLAN 0 to HW filter on device eth0
[ 7.254493] usb 1-1.3: new high-speed USB device number 3 using ehci-platform
[ 8.448525] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 8.487324] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 8.742526] procd: - early -
[ 8.745597] procd: - watchdog -
[ 9.224839] procd: - watchdog -
[ 9.228413] procd: - ubus -
[ 9.551924] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.648488] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.655622] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.663177] procd: - init -
[ 10.501305] kmodloader: loading kernel modules from /etc/modules.d/*
[ 10.700822] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.730928] Loading modules backported from Linux version v4.19.137-0-gc076c79e03c6
[ 10.738823] Backport generated by backports.git v4.19.137-1-0-g60c3a249
[ 10.766810] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.793881] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 10.929338] xt_time: kernel timezone is -0000
[ 10.996588] urngd: jent-rng init failed, err: 2
[ 11.047863] PPP generic driver version 2.4.2
[ 11.055294] NET: Registered protocol family 24
[ 11.090317] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[ 11.097776] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[ 11.105710] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 11.113456] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 11.124491] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 34.173928] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 34.181846] jffs2_build_filesystem(): unlocking the mtd device...
[ 34.202586] done.
[ 34.210868] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 34.776515] 8021q: adding VLAN 0 to HW filter on device eth0
[ 34.825820] br-lan: port 1(eth0.1) entered blocking state
[ 34.831348] br-lan: port 1(eth0.1) entered disabled state
[ 34.837319] device eth0.1 entered promiscuous mode
[ 34.842214] device eth0 entered promiscuous mode
[ 34.904287] br-lan: port 1(eth0.1) entered blocking state
[ 34.909813] br-lan: port 1(eth0.1) entered forwarding state
[ 34.915805] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 35.856533] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 105.752588] random: crng init done
[ 105.756081] random: 6 urandom warning(s) missed due to ratelimiting
[ 149.198045] done.
[ 149.200064] jffs2: notice: (1245) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 149.460950] overlayfs: upper fs does not support tmpfile.
I don't see a cdc_ether ..
usb 1-1.3: new high-speed USB device number 3 using ehci-platform
Here a device (your modem?) is detected and registered on the USB bus, but no driver claims it.
That looks like the first boot of a new install, did you install the cdc driver yet?
Start from posting the result of cat /sys/kernel/debug/usb/devices