KuWfi Tenbay WIFI-6 AX T-MB5EU-V01
edited
post boot logs too, stock and openwrt.
firmware is in snapshots
boot log with openwrt:
U-Boot SPL 2018.09-gd98fab1 (Nov 13 2020 - 20:31:23 +0800)
Trying to boot from NOR
U-Boot 2018.09-gd98fab1 (Nov 13 2020 - 20:31:23 +0800)
CPU: MediaTek MT7621AT ver 1, eco 3
Clocks: CPU: 880MHz, DDR: 1200MHz, Bus: 220MHz, XTAL: 40MHz
Model: MediaTek MT7621 reference board
DRAM: 256 MiB
Loading Environment from SPI Flash... SF: Detected H25Q128b with page size 256 Bytes, erase size 64 KiB, total 16 MiB
OK
In: uartlite0@1e000c00
Out: uartlite0@1e000c00
Err: uartlite0@1e000c00
Net:
Warning: eth@1e100000 (eth0) using random MAC address - da:6d:cc:f4:fb:3c
eth0: eth@1e100000
Hit any key to stop autoboot: 0
*** U-Boot Boot Menu ***
1. Startup system (Default)
2. Upgrade firmware
3. Upgrade bootloader
4. Upgrade bootloader (advanced mode)
5. Load image
0. U-Boot console
Press UP/DOWN to move, ENTER to select
## Loading kernel from FIT Image at bfc90000 ...
Using 'config@1' configuration
Trying 'kernel-1' kernel subimage
Description: MIPS OpenWrt Linux-5.4.124
Type: Kernel Image
Compression: lzma compressed
Data Start: 0xbfc900e4
Data Size: 2485874 Bytes = 2.4 MiB
Architecture: MIPS
OS: Linux
Load Address: 0x80001000
Entry Point: 0x80001000
Hash algo: crc32
Hash value: 236fa28e
Hash algo: sha1
Hash value: aa6764220a0b393168689d4660d4164b597ec68e
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at bfc90000 ...
Using 'config@1' configuration
Trying 'fdt-1' fdt subimage
Description: MIPS OpenWrt tenbay_wr1800k device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0xbfeef098
Data Size: 11097 Bytes = 10.8 KiB
Architecture: MIPS
Hash algo: crc32
Hash value: 7b69e110
Hash algo: sha1
Hash value: a43095aa1b1f2fcf97b264ad5ec0d1ec3b32f100
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0xbfeef098
Uncompressing Kernel Image ... OK
Loading Device Tree to 8fe97000, end 8fe9cb58 ... OK
[ 0.000000] Linux version 5.4.124 (user@debian) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16957-3d026d2425)) #0 SMP Tue Jun 15 10:48:20 2021
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Tenbay WR1800K
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem [mem 0x0000000010000000-0x000000008fe99fff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] node 0: [mem 0x000000008fe97000-0x000000008fe99fff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000008fe99fff]
[ 0.000000] percpu: Embedded 14 pages/cpu s26480 r8192 d22672 u57344
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64963
[ 0.000000] Kernel command line: console=ttyS0,115200
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Writing ErrCtl register=00001640
[ 0.000000] Readback ErrCtl register=00001640
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 231916K/262156K available (6025K kernel code, 204K rwdata, 1272K rodata, 1252K init, 230K bss, 30240K reserved, 0K cma-reserved, 12K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] random: get_random_bytes called from start_kernel+0x36c/0x584 with crng_init=0
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.000008] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[ 0.007806] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.073972] pid_max: default: 32768 minimum: 301
[ 0.078769] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.085969] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.096493] rcu: Hierarchical SRCU implementation.
[ 0.101829] smp: Bringing up secondary CPUs ...
[ 9.108352] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 9.108363] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 9.108376] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 9.108477] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.166614] Synchronize counters for CPU 1: done.
[ 8.508938] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 8.508946] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 8.508953] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 8.509013] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.257348] Synchronize counters for CPU 2: done.
[ 8.598316] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 8.598324] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 8.598332] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 8.598395] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.342528] Synchronize counters for CPU 3: done.
[ 0.372387] smp: Brought up 1 node, 4 CPUs
[ 0.381410] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.391171] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.398246] pinctrl core: initialized pinctrl subsystem
[ 0.405002] NET: Registered protocol family 16
[ 0.437635] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[ 0.448934] clocksource: Switched to clocksource GIC
[ 0.455375] thermal_sys: Registered thermal governor 'step_wise'
[ 0.455870] NET: Registered protocol family 2
[ 0.466497] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.474261] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.482568] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.490159] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.497230] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.503673] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.510152] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.517290] NET: Registered protocol family 1
[ 0.521612] PCI: CLS 0 bytes, default 32
[ 0.758875] 4 CPUs re-calibrate udelay(lpj = 2924544)
[ 0.765573] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.774815] random: fast init done
[ 0.787422] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.793214] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.804735] bounce: pool size: 64 pages
[ 0.809873] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.815665] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.821519] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.827905] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 0.835645] printk: console [ttyS0] disabled
[ 0.839940] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 0.848930] printk: console [ttyS0] enabled
[ 0.848930] printk: console [ttyS0] enabled
[ 0.857163] printk: bootconsole [early0] disabled
[ 0.857163] printk: bootconsole [early0] disabled
[ 0.869517] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 0.875762] spi-nor spi0.0: bh25q128as (16384 Kbytes)
[ 0.880943] 5 fixed-partitions partitions found on MTD device spi0.0
[ 0.887263] Creating 5 MTD partitions on "spi0.0":
[ 0.892059] 0x000000000000-0x000000030000 : "u-boot"
[ 0.898215] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.904660] 0x000000040000-0x000000050000 : "product"
[ 0.910843] 0x000000050000-0x000000090000 : "factory"
[ 0.916973] 0x000000090000-0x000001000000 : "firmware"
[ 0.923443] 2 fit-fw partitions found on MTD device firmware
[ 0.929144] Creating 2 MTD partitions on "firmware":
[ 0.934105] 0x000000000000-0x000000270000 : "kernel"
[ 0.940357] 0x000000262138-0x000000f70000 : "rootfs"
[ 0.946615] mtd: device 6 (rootfs) set to be root filesystem
[ 0.952388] 1 squashfs-split partitions found on MTD device rootfs
[ 0.958547] 0x0000005f0000-0x000000f70000 : "rootfs_data"
[ 0.966400] libphy: Fixed MDIO Bus: probed
[ 1.009263] libphy: mdio: probed
[ 1.012678] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 1.021998] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[ 1.032545] mt7621-pci 1e140000.pcie: Parsing DT failed
[ 1.040374] NET: Registered protocol family 10
[ 1.046169] Segment Routing with IPv6
[ 1.050011] NET: Registered protocol family 17
[ 1.054713] 8021q: 802.1Q VLAN Support v1.8
[ 1.062524] gpio-487 (i2c-gpio): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 1.072037] gpio-488 (i2c-gpio): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[ 1.081824] i2c-gpio i2c-gpio: using lines 487 (SDA) and 488 (SCL)
[ 1.088137] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 1.106776] libphy: dsa slave smi: probed
[ 1.111296] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY]
[ 1.120940] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY]
[ 1.130636] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY]
[ 1.140409] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY]
[ 1.150162] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY]
[ 1.160006] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[ 1.171236] DSA: tree 0 setup
[ 1.174577] rt2880-pinmux pinctrl: pcie is already enabled
[ 1.180079] mt7621-pci 1e140000.pcie: Error applying setting, reverse things back
[ 1.187679] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[ 1.195263] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[ 1.302642] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[ 1.308203] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[ 1.413677] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 1.420626] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 1.425479] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 1.430355] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 1.439817] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 1.446160] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 1.453031] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.459899] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.465399] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 1.471429] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.477671] pci 0000:00:00.0: reg 0x14: [mem 0x60400000-0x6040ffff]
[ 1.483998] pci 0000:00:00.0: supports D1
[ 1.487989] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.494155] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 1.500190] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.506432] pci 0000:00:01.0: reg 0x14: [mem 0x60410000-0x6041ffff]
[ 1.512746] pci 0000:00:01.0: supports D1
[ 1.516738] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 1.524128] pci 0000:01:00.0: [14c3:7916] type 00 class 0x000280
[ 1.530208] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[ 1.537412] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
[ 1.544633] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
[ 1.551958] pci 0000:01:00.0: supports D1 D2
[ 1.556208] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.562844] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[ 1.578022] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.583259] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.589354] pci 0000:00:00.0: bridge window [mem 0x60000000-0x601fffff pref]
[ 1.596548] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.603380] pci 0000:02:00.0: [14c3:7915] type 00 class 0x000280
[ 1.609447] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[ 1.616652] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
[ 1.623872] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
[ 1.631198] pci 0000:02:00.0: supports D1 D2
[ 1.635448] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.642083] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[ 1.657268] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 1.662505] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 1.668575] pci 0000:00:01.0: bridge window [mem 0x60200000-0x603fffff pref]
[ 1.675785] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 1.682436] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 1.689040] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.695971] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 1.702572] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.709525] pci 0000:00:00.0: BAR 9: assigned [mem 0x60000000-0x601fffff pref]
[ 1.716715] pci 0000:00:01.0: BAR 9: assigned [mem 0x60200000-0x603fffff pref]
[ 1.723929] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff]
[ 1.730713] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff]
[ 1.737472] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff]
[ 1.744248] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff]
[ 1.751034] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit pref]
[ 1.758754] pci 0000:01:00.0: BAR 2: assigned [mem 0x60100000-0x60103fff 64bit pref]
[ 1.766493] pci 0000:01:00.0: BAR 4: assigned [mem 0x60104000-0x60104fff 64bit pref]
[ 1.774231] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.779193] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff]
[ 1.785954] pci 0000:00:00.0: bridge window [mem 0x60000000-0x601fffff pref]
[ 1.793171] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit pref]
[ 1.800913] pci 0000:02:00.0: BAR 2: assigned [mem 0x60300000-0x60303fff 64bit pref]
[ 1.808633] pci 0000:02:00.0: BAR 4: assigned [mem 0x60304000-0x60304fff 64bit pref]
[ 1.816368] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 1.821329] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff]
[ 1.828088] pci 0000:00:01.0: bridge window [mem 0x60200000-0x603fffff pref]
[ 1.835913] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off
[ 1.843286] hctosys: unable to open rtc device (rtc0)
[ 1.853574] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[ 1.864908] Freeing unused kernel memory: 1252K
[ 1.869501] This architecture does not have kernel memory protection.
[ 1.875911] Run /sbin/init as init process
[ 2.357738] init: Console is alive
[ 2.361458] init: - watchdog -
[ 3.136427] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.232690] usbcore: registered new interface driver usbfs
[ 3.238268] usbcore: registered new interface driver hub
[ 3.243721] usbcore: registered new device driver usb
[ 3.257944] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator
[ 3.266685] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
[ 3.275648] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 3.280984] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[ 3.299121] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010
[ 3.308293] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
[ 3.315288] hub 1-0:1.0: USB hub found
[ 3.319166] hub 1-0:1.0: 2 ports detected
[ 3.323757] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 3.329171] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[ 3.336634] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[ 3.343365] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.352410] hub 2-0:1.0: USB hub found
[ 3.356223] hub 2-0:1.0: 1 port detected
[ 3.365066] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.389287] init: - preinit -
[ 4.069516] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 4.077809] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 4.086300] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 4.199138] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.263237] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.301720] random: jshn: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 7.667838] jffs2: notice: (575) jffs2_build_xattr_subsystem: complete building xattr subsystem, 6 of xdatum (0 unchecked, 1 orphan) and 7 of xref (1 dead, 0 orphan) found.
[ 7.685073] mount_root: switching to jffs2 overlay
[ 7.695826] overlayfs: upper fs does not support tmpfile.
[ 7.705952] urandom-seed: Seeding with /etc/urandom.seed
[ 7.775663] procd: - early -
[ 7.778641] procd: - watchdog -
[ 8.369116] procd: - watchdog -
[ 8.372899] procd: - ubus -
[ 8.469538] urandom_read: 6 callbacks suppressed
[ 8.469550] random: ubusd: uninitialized urandom read (4 bytes read)
[ 8.536747] procd: - init -
Please press Enter to activate this console.
[ 9.156374] kmodloader: loading kernel modules from /etc/modules.d/*
[ 9.175647] Loading modules backported from Linux version v5.10.42-0-g65859eca4dff
[ 9.183230] Backport generated by backports.git v5.10.42-1-0-gbee5c545
[ 9.208273] xt_time: kernel timezone is -0000
[ 9.295859] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=23
[ 9.301324] pci 0000:00:00.0: enabling device (0006 -> 0007)
[ 9.304023] urngd: v1.0.2 started.
[ 9.306971] mt7915e_hif 0000:01:00.0: enabling device (0000 -> 0002)
[ 9.317163] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=24
[ 9.322613] pci 0000:00:01.0: enabling device (0006 -> 0007)
[ 9.328263] mt7915e 0000:02:00.0: enabling device (0000 -> 0002)
[ 9.442250] random: crng init done
[ 9.459315] mt7915e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20201105222230a
[ 9.459315]
[ 9.777202] mt7915e 0000:02:00.0: WM Firmware Version: ____000000, Build Time: 20201105222304
[ 9.810736] mt7915e 0000:02:00.0: WA Firmware Version: DEV_000000, Build Time: 20201105222323
[ 9.956325] PPP generic driver version 2.4.2
[ 9.962282] NET: Registered protocol family 24
[ 9.978523] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 15.914344] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 15.932190] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 15.940808] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 15.947667] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 15.956548] 8021q: adding VLAN 0 to HW filter on device lan1
[ 15.966481] br-lan: port 1(lan1) entered blocking state
[ 15.971855] br-lan: port 1(lan1) entered disabled state
[ 15.978866] device lan1 entered promiscuous mode
[ 15.983899] device eth0 entered promiscuous mode
[ 15.992970] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 16.020153] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 16.027361] 8021q: adding VLAN 0 to HW filter on device lan2
[ 16.036928] br-lan: port 2(lan2) entered blocking state
[ 16.042256] br-lan: port 2(lan2) entered disabled state
[ 16.049144] device lan2 entered promiscuous mode
[ 16.066059] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 16.073382] 8021q: adding VLAN 0 to HW filter on device lan3
[ 16.082536] br-lan: port 3(lan3) entered blocking state
[ 16.087810] br-lan: port 3(lan3) entered disabled state
[ 16.095094] device lan3 entered promiscuous mode
[ 16.111863] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode
[ 16.119215] 8021q: adding VLAN 0 to HW filter on device lan4
[ 16.128853] br-lan: port 4(lan4) entered blocking state
[ 16.134197] br-lan: port 4(lan4) entered disabled state
[ 16.141458] device lan4 entered promiscuous mode
[ 16.167808] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode
[ 16.174980] 8021q: adding VLAN 0 to HW filter on device wan
[ 20.119427] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 20.126944] br-lan: port 1(lan1) entered blocking state
[ 20.132209] br-lan: port 1(lan1) entered forwarding state
[ 20.138545] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 20.200342] mt7530 mdio-bus:1f lan2: Link is Up - 1Gbps/Full - flow control rx/tx
[ 20.207858] br-lan: port 2(lan2) entered blocking state
[ 20.213125] br-lan: port 2(lan2) entered forwarding state
[ 21.239280] mt7530 mdio-bus:1f lan2: Link is Down
[ 21.244207] br-lan: port 2(lan2) entered disabled state
[ 24.359333] mt7530 mdio-bus:1f lan2: Link is Up - 1Gbps/Full - flow control rx/tx
[ 24.366849] br-lan: port 2(lan2) entered blocking state
[ 24.372099] br-lan: port 2(lan2) entered forwarding state
BusyBox v1.33.1 (2021-06-15 10:48:20 UTC) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r16957-3d026d2425
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/#
next project:
replace stupid 16M memory flash with 32 or 64 M ( not much memory with samba4 )
yeah, samba4 is a space hog, you could try cifs instead 
I totally agree with @frollic.
I don't know if you really want to change the flash memory as you will lose upstream support and have to patch the image yourself.
CIFS is indeed a good choice on those tiny devices.
Flash memory 16M is almost unknown : BoHong bh25q128as ..
to replace the memory it is extremely easy because there is no component nearby.
yes it will be necessary to see with the source code ...
at the moment I am looking for 128M memories to replace on all my boxes !!!
Flash memory 16M is almost unknown : BoHong bh25q128as replaced by a Macronix 32MB
no problem with flash boot ( tftp -> console 2 ... ) for flash old 16M content
build new firmware for 32M flash memory
for read old content : CH341 -> NeoProgrammer_2.1.0.19
after write content in as MX25L25635E or WINBOND 256MB
startup -> tftp key 2 .... OpenWrt firmware
firstboot -> reboot -f
Variant for 32M version
modify in mt7621.mk
IMAGE_SIZE := 32448k
modify in mt7621_tenbay_t-mb5eu-32M.dts
reg = <0x90000 0x1F70000>
build
flash new firmware with tftp
if you have a USB NTFS problem:with ntfs-3g
solved with ln -s /usr/bin/ntfs-3g /sbin/mount.ntfs
reboot
If you have a problem for AP <-> Client solved with last fix
3 Likes
If your problem is solved, please consider marking this topic as [Solved]. See How to mark a topic as [Solved] for a short how-to.
New for snapshots & bad MAC Address
Does 5GHz work properly for you?
It's so bad on all my T-MB5EU-V01s (Mar 9 snapshot) that clients won't even try connect when they're straight next to them, despite setting it to max transmission power (which at 22dB/158mW is poor, my country allows 27/500 on most and even 30/1000 on some 5GHz channels).
I have to force it by disabling 2.4GHz (which works fine).
Also, running 5GHz in N/AC mode makes clients not even find the SSID anymore.
Today's snapshot breaks wifi entirely, probably due to the changes to openwrt's mt76 repo over the past two days.
Still, could you please answer if 5GHz (AC/AX, 80/160MHz) did work for you?
Late answer to myself: Days after I wrote that question, there were fixes to the mt76 driver that now allow the wifi (vanilla settings) to run smoothly on both bands.
I'm still using ptpt52's branch as it contains a couple of useful commits, such as disabling 160MHz for 5GHz – the router's MT7915 DBDC doesn't support it, it's offered in error.
This is an interesting router, one which supports both WiFi6 and USB3. Could you please post some performance benchmarks? E.g. a few of those:
- WAN <-> wired LAN routing performance using iperf3, with flow offloading disabled / software / hardware)
- WLAN <-> LAN throughput as a pure AP
- CIFS serving of a large file from a USB3 drive via LAN (read-only)
- CIFS serving of a large file from a USB3 drive via WLAN (read-only)
- Wireguard, IKEv2, or OpenVPN throughput
openssl speed
I am interested too
does anybody know how to recover this device, nothing on the web about that.
this is a zero info device.
device is in bootloop cannot stop from serial, tftp not working.
bricco1981
Did you receive my messages with the original firmware & some info ?
....
Could you send me the same info please?
Tried upgrading from a Dec22 build to today's. Now it's bricked, constant red LED after 3s. Reset button and long-pressing power has no effect.
Any hint how to recover is appreciated.
Also, if somebody is able to run a recent build without issue, please tell.