@frollic @d687r02j8g bro,If I have done any mistake please forgive me and correct me. i tried and got this...
1
regValue=[0x0]
Port3 Link DOWN!
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
6: Load Flash code then burn to Flash via TFTP.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3
You choosed 2
0
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.1.1) ==:192.168.1.1
Input server IP (192.168.1.2) ==:192.168.1.2
Input Linux Kernel filename () ==:TOTOLINK_C8343R-1C_X5000R_IP04433_MT7621A_SPI_16M256M_V9.1.0u.6118_B20201102_ALL.web
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'TOTOLINK_C8343R-1C_X5000R_IP04433_MT7621A_SPI_16M256M_V9.1.0u.6118_B20201102_ALL.web'.
TIMEOUT_COUNT=10,Load address: 0x88000000
Loading: checksum bad!!!
checksum bad!!!
checksum bad!!!
checksum bad!!!
checksum bad!!!
checksum bad!!!
checksum bad!!!
Got ARP REPLY, set server/gtwy eth addr (04:42:1a:99:5d:9b)
Got it
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
####################
done
Bytes transferred = 9086104 (8aa498 hex)
LoadAddr=88000000 NetBootFileXferSize= 008aa498
upfile len = 0x8aa498
custom img - type 2
userdatabin erase+write
raspi_erase: offs:f00000 len:10000
.
orig web erase+write
Abort: image size larger than 2097152!
## Booting image at bfc50000 ...
Image Name: C8343R-9999
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 5763479 Bytes = 5.5 MB
Load Address: 80001000
Entry Point: 80001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 256
Starting kernel ...
[ 0.000000] Linux version 5.10.176 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r20134-5f15225c1e) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Thu Apr 27 20:28:15 2023
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is TOTOLINK X5000R
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] percpu: Embedded 15 pages/cpu s30480 r8192 d22768 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Writing ErrCtl register=00004014
[ 0.000000] Readback ErrCtl register=00004014
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 246356K/262144K available (7064K kernel code, 631K rwdata, 832K rodata, 4196K init, 243K bss, 15788K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000012] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.007941] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.017000] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.083161] pid_max: default: 32768 minimum: 301
[ 0.087922] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.095125] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.105749] rcu: Hierarchical SRCU implementation.
[ 0.110798] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.118911] smp: Bringing up secondary CPUs ...
[ 0.124198] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.124209] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.124220] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.124295] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.178697] Synchronize counters for CPU 1: done.
[ 0.211144] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.211153] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.211161] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.211207] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.270109] Synchronize counters for CPU 2: done.
[ 0.300716] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.300725] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.300733] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.300781] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.355296] Synchronize counters for CPU 3: done.
[ 0.385162] smp: Brought up 1 node, 4 CPUs
[ 0.393127] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.402949] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.409964] pinctrl core: initialized pinctrl subsystem
[ 0.417588] NET: Registered protocol family 16
[ 0.423190] thermal_sys: Registered thermal governor 'step_wise'
[ 0.424525] cpuidle: using governor teo
[ 0.473158] clocksource: Switched to clocksource GIC
[ 0.479882] NET: Registered protocol family 2
[ 0.484722] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.493400] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.501708] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.509375] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.516461] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.522894] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.529372] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.536608] NET: Registered protocol family 1
[ 0.540909] PCI: CLS 0 bytes, default 32
[ 4.216508] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 4.226993] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 4.232739] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 4.243418] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 4.252608] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 4.258540] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 4.264484] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 4.270947] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 4.281464] printk: console [ttyS0] disabled
[ 4.285792] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 4.294795] printk: console [ttyS0] enabled
[ 4.294795] printk: console [ttyS0] enabled
[ 4.303034] printk: bootconsole [early0] disabled
[ 4.303034] printk: bootconsole [early0] disabled
[ 4.315754] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 4.322375] spi-nor spi0.0: unrecognized JEDEC id bytes: 5e 40 18 5e 40 18
[ 4.329301] spi-nor: probe of spi0.0 failed with error -2
[ 4.375065] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 4.383763] mtk_soc_eth 1e100000.ethernet: generated random MAC address ca:7a:9a:31:94:74
[ 4.392777] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[ 4.401971] i2c /dev entries driver
[ 4.408016] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 4.414759] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 4.423558] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000
[ 4.431710] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 4.439968] mt7621-pci 1e140000.pcie: Parsing DT failed
[ 4.447613] NET: Registered protocol family 10
[ 4.453896] Segment Routing with IPv6
[ 4.457654] NET: Registered protocol family 17
[ 4.462151] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 4.475442] 8021q: 802.1Q VLAN Support v1.8
[ 4.482990] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 4.566154] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=26)
[ 4.578404] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=27)
[ 4.590660] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=28)
[ 4.602881] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=29)
[ 4.615156] mt7530 mdio-bus:1f wan (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7530 PHY] (irq=30)
[ 4.627584] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[ 4.637997] DSA: tree 0 setup
[ 4.641258] rt2880-pinmux pinctrl: pcie is already enabled
[ 4.646828] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 4.653535] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 4.662311] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000
[ 4.670478] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 4.678744] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[ 4.686480] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[ 4.694097] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22
[ 4.801480] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[ 4.807069] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[ 4.912761] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 4.919712] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 4.924590] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 4.929451] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 4.938887] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 4.945251] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 4.952102] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 4.958965] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 4.964447] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff])
[ 4.974655] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 4.980654] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 4.986921] pci 0000:00:00.0: reg 0x14: initial BAR value 0x00000000 invalid
[ 4.993955] pci 0000:00:00.0: reg 0x14: [mem size 0x00010000]
[ 4.999744] pci 0000:00:00.0: supports D1
[ 5.003751] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 5.010004] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 5.016052] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 5.022296] pci 0000:00:01.0: reg 0x14: initial BAR value 0x00000000 invalid
[ 5.029328] pci 0000:00:01.0: reg 0x14: [mem size 0x00010000]
[ 5.035128] pci 0000:00:01.0: supports D1
[ 5.039122] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 5.046249] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 5.054264] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 5.062470] pci 0000:01:00.0: [14c3:7916] type 00 class 0x000280
[ 5.068516] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[ 5.075560] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000 64bit pref]
[ 5.082245] pci 0000:01:00.0: reg 0x18: initial BAR value 0x00000000 invalid
[ 5.089277] pci 0000:01:00.0: reg 0x18: [mem size 0x00004000 64bit pref]
[ 5.095987] pci 0000:01:00.0: reg 0x20: initial BAR value 0x00000000 invalid
[ 5.103006] pci 0000:01:00.0: reg 0x20: [mem size 0x00001000 64bit pref]
[ 5.109819] pci 0000:01:00.0: supports D1 D2
[ 5.114088] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 5.120716] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 5.136716] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 5.141938] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 5.148028] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 5.154806] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff pref]
[ 5.162003] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 5.168884] pci 0000:02:00.0: [14c3:7915] type 00 class 0x000280
[ 5.174943] pci 0000:02:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[ 5.181970] pci 0000:02:00.0: reg 0x10: [mem size 0x00100000 64bit pref]
[ 5.188670] pci 0000:02:00.0: reg 0x18: initial BAR value 0x00000000 invalid
[ 5.195704] pci 0000:02:00.0: reg 0x18: [mem size 0x00004000 64bit pref]
[ 5.202390] pci 0000:02:00.0: reg 0x20: initial BAR value 0x00000000 invalid
[ 5.209422] pci 0000:02:00.0: reg 0x20: [mem size 0x00001000 64bit pref]
[ 5.216231] pci 0000:02:00.0: supports D1 D2
[ 5.220483] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 5.227133] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 5.243368] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 5.248593] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 5.254677] pci 0000:00:01.0: bridge window [mem 0x60000000-0x600fffff]
[ 5.261436] pci 0000:00:01.0: bridge window [mem 0x60000000-0x600fffff pref]
[ 5.268646] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 5.275297] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 5.281882] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 5.288841] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 5.295442] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 5.302378] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 5.309156] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref]
[ 5.316367] pci 0000:00:01.0: BAR 8: assigned [mem 0x60300000-0x603fffff]
[ 5.323148] pci 0000:00:01.0: BAR 9: assigned [mem 0x60400000-0x605fffff pref]
[ 5.330340] pci 0000:00:00.0: BAR 1: assigned [mem 0x60600000-0x6060ffff]
[ 5.337123] pci 0000:00:01.0: BAR 1: assigned [mem 0x60610000-0x6061ffff]
[ 5.343910] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff]
[ 5.350671] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff]
[ 5.357457] pci 0000:01:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref]
[ 5.365198] pci 0000:01:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref]
[ 5.372920] pci 0000:01:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref]
[ 5.380655] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 5.385618] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff]
[ 5.392377] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 5.399151] pci 0000:00:00.0: bridge window [mem 0x60100000-0x602fffff pref]
[ 5.406377] pci 0000:02:00.0: BAR 0: assigned [mem 0x60400000-0x604fffff 64bit pref]
[ 5.414119] pci 0000:02:00.0: BAR 2: assigned [mem 0x60500000-0x60503fff 64bit pref]
[ 5.421840] pci 0000:02:00.0: BAR 4: assigned [mem 0x60504000-0x60504fff 64bit pref]
[ 5.429575] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 5.434535] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff]
[ 5.441295] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff]
[ 5.448068] pci 0000:00:01.0: bridge window [mem 0x60400000-0x605fffff pref]
[ 5.472068] Freeing unused kernel memory: 4196K
[ 5.476660] This architecture does not have kernel memory protection.
[ 5.483116] Run /init as init process
[ 5.487153] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 5.941325] init: Console is alive
[ 5.945155] init: - watchdog -
[ 5.959366] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.973318] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.983576] init: - preinit -
[ 6.180747] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.259326] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.299298] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.550735] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 6.559570] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 6.563406] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 6.574991] 8021q: adding VLAN 0 to HW filter on device lan1
[ 6.583314] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 9.677953] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 9.685510] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready
[ 10.730444] mt7530 mdio-bus:1f lan1: Link is Down
[ 10.744766] procd: - early -
[ 10.747879] procd: - watchdog -
[ 11.303404] procd: - watchdog -
[ 11.307558] procd: - ubus -
[ 11.317786] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.363933] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.370757] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.380570] procd: - init -
Please press Enter to activate this console.
[ 11.735102] kmodloader: loading kernel modules from /etc/modules.d/*
[ 11.796595] PPP generic driver version 2.4.2
[ 11.802461] NET: Registered protocol family 24
[ 11.814468] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 11.954147] urngd: v1.0.2 started.
[ 12.128710] random: crng init done
[ 12.132105] random: 30 urandom warning(s) missed due to ratelimiting
[ 30.817354] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 30.833932] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 30.843600] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 30.846182] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 30.859343] 8021q: adding VLAN 0 to HW filter on device lan1
[ 30.868196] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 30.875752] br-lan: port 1(lan1) entered blocking state
[ 30.881047] br-lan: port 1(lan1) entered disabled state
[ 30.888612] device lan1 entered promiscuous mode
[ 30.893380] device eth0 entered promiscuous mode
[ 30.929862] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 30.937208] 8021q: adding VLAN 0 to HW filter on device lan2
[ 30.946783] br-lan: port 2(lan2) entered blocking state
[ 30.952093] br-lan: port 2(lan2) entered disabled state
[ 30.959385] device lan2 entered promiscuous mode
[ 30.980602] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 30.988070] 8021q: adding VLAN 0 to HW filter on device lan3
[ 30.998326] br-lan: port 3(lan3) entered blocking state
[ 31.003672] br-lan: port 3(lan3) entered disabled state
[ 31.011753] device lan3 entered promiscuous mode
[ 31.030660] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode
[ 31.038029] 8021q: adding VLAN 0 to HW filter on device lan4
[ 31.048523] br-lan: port 4(lan4) entered blocking state
[ 31.054075] br-lan: port 4(lan4) entered disabled state
[ 31.060926] device lan4 entered promiscuous mode
[ 31.087701] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode
[ 31.094918] 8021q: adding VLAN 0 to HW filter on device wan
[ 33.820643] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 33.828215] br-lan: port 1(lan1) entered blocking state
[ 33.833469] br-lan: port 1(lan1) entered forwarding state
[ 33.840084] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
What to do now bro?