I have compiled a custom image with luci and the patches for the chip. Use this if the snapshot doesn't work.
https://anonfiles.com/03c5Xbsbz6/openwrt_ramips_mt7621_totolink_x5000r_squashfs_sysupgrade_bin
sha256
709891c1edaacebd2c95ad1374533606821996d2c2746d0e3ae44b8449943a57 openwrt-ramips-mt7621-totolink_x5000r-squashfs-sysupgrade.bin
@d687r02j8g bro i have tried option 2 with the snapshot image. here is the output..
1
regValue=[0x0]
Port3 Link DOWN!
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
6: Load Flash code then burn to Flash via TFTP.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3
You choosed 2
0
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.1.1) ==:192.168.1.1
Input server IP (192.168.1.2) ==:192.168.1.2
Input Linux Kernel filename (openwrt-ramips-mt7621-totolink_x5000r-initramfs-kernel.bin) ==:openwrt-ramips-mt7621-totolink_x5000r-squashfs-sysupgrade.bin
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'openwrt-ramips-mt7621-totolink_x5000r-squashfs-sysupgrade.bin'.
TIMEOUT_COUNT=10,Load address: 0x88000000
Loading: checksum bad!!!
checksum bad!!!
checksum bad!!!
checksum bad!!!
checksum bad!!!
Got ARP REPLY, set server/gtwy eth addr (04:42:1a:99:5d:9b)
Got it
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
##########################################################
done
Bytes transferred = 6619725 (65024d hex)
LoadAddr=88000000 NetBootFileXferSize= 0065024d
upfile len = 0x65024d
orig web erase+write
Abort: image size larger than 2097152!
## Booting image at bfc50000 ...
Image Name: C8343R-9999
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 5763479 Bytes = 5.5 MB
Load Address: 80001000
Entry Point: 80001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 256
Starting kernel ...
[ 0.000000] Linux version 5.10.176 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r20134-5f15225c1e) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Thu Apr 27 20:28:15 2023
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is TOTOLINK X5000R
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] percpu: Embedded 15 pages/cpu s30480 r8192 d22768 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Writing ErrCtl register=00004004
[ 0.000000] Readback ErrCtl register=00004004
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 246356K/262144K available (7064K kernel code, 631K rwdata, 832K rodata, 4196K init, 243K bss, 15788K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000012] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.007941] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.017001] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.083162] pid_max: default: 32768 minimum: 301
[ 0.087923] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.095125] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.105752] rcu: Hierarchical SRCU implementation.
[ 0.110802] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.118915] smp: Bringing up secondary CPUs ...
[ 0.124203] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.124213] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.124225] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.124299] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.178699] Synchronize counters for CPU 1: done.
[ 0.211146] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.211156] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.211163] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.211210] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.270110] Synchronize counters for CPU 2: done.
[ 0.300718] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.300727] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.300735] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.300784] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.355298] Synchronize counters for CPU 3: done.
[ 0.385165] smp: Brought up 1 node, 4 CPUs
[ 0.393130] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.402953] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.409968] pinctrl core: initialized pinctrl subsystem
[ 0.417612] NET: Registered protocol family 16
[ 0.423300] thermal_sys: Registered thermal governor 'step_wise'
[ 0.424043] cpuidle: using governor teo
[ 0.473220] clocksource: Switched to clocksource GIC
[ 0.479889] NET: Registered protocol family 2
[ 0.484707] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.493113] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.501527] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.509179] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.516263] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.522692] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.529172] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.536387] NET: Registered protocol family 1
[ 0.540682] PCI: CLS 0 bytes, default 32
[ 4.216441] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 4.226917] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 4.232663] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 4.243327] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 4.252412] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 4.258321] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 4.264182] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 4.270601] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 4.281218] printk: console [ttyS0] disabled
[ 4.285545] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 4.294535] printk: console [ttyS0] enabled
[ 4.294535] printk: console [ttyS0] enabled
[ 4.302771] printk: bootconsole [early0] disabled
[ 4.302771] printk: bootconsole [early0] disabled
[ 4.315455] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 4.322089] spi-nor spi0.0: unrecognized JEDEC id bytes: 5e 40 18 5e 40 18
[ 4.329010] spi-nor: probe of spi0.0 failed with error -2
[ 4.374975] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 4.383687] mtk_soc_eth 1e100000.ethernet: generated random MAC address 8a:e4:2c:55:1d:f8
[ 4.392622] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[ 4.401917] i2c /dev entries driver
[ 4.407604] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 4.414352] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 4.423146] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000
[ 4.431332] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 4.439601] mt7621-pci 1e140000.pcie: Parsing DT failed
[ 4.446793] NET: Registered protocol family 10
[ 4.453041] Segment Routing with IPv6
[ 4.456850] NET: Registered protocol family 17
[ 4.461359] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 4.474610] 8021q: 802.1Q VLAN Support v1.8
[ 4.482123] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 4.565901] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=26)
[ 4.578287] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=27)
[ 4.590507] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=28)
[ 4.602721] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=29)
[ 4.615018] mt7530 mdio-bus:1f wan (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7530 PHY] (irq=30)
[ 4.627495] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[ 4.637906] DSA: tree 0 setup
[ 4.641177] rt2880-pinmux pinctrl: pcie is already enabled
[ 4.646757] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 4.653463] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 4.662237] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000
[ 4.670412] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 4.678667] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[ 4.686401] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[ 4.694052] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22
[ 4.801441] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[ 4.807031] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[ 4.912731] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 4.919683] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 4.924556] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 4.929417] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 4.938864] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 4.945227] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 4.952076] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 4.958936] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 4.964425] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff])
[ 4.974622] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 4.980620] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 4.986878] pci 0000:00:00.0: reg 0x14: initial BAR value 0x00000000 invalid
[ 4.993927] pci 0000:00:00.0: reg 0x14: [mem size 0x00010000]
[ 4.999716] pci 0000:00:00.0: supports D1
[ 5.003722] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 5.009982] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 5.016043] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 5.022289] pci 0000:00:01.0: reg 0x14: initial BAR value 0x00000000 invalid
[ 5.029320] pci 0000:00:01.0: reg 0x14: [mem size 0x00010000]
[ 5.035115] pci 0000:00:01.0: supports D1
[ 5.039106] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 5.046211] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 5.054229] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 5.062449] pci 0000:01:00.0: [14c3:7916] type 00 class 0x000280
[ 5.068502] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[ 5.075544] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000 64bit pref]
[ 5.082230] pci 0000:01:00.0: reg 0x18: initial BAR value 0x00000000 invalid
[ 5.089261] pci 0000:01:00.0: reg 0x18: [mem size 0x00004000 64bit pref]
[ 5.095968] pci 0000:01:00.0: reg 0x20: initial BAR value 0x00000000 invalid
[ 5.102987] pci 0000:01:00.0: reg 0x20: [mem size 0x00001000 64bit pref]
[ 5.109793] pci 0000:01:00.0: supports D1 D2
[ 5.114068] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 5.120696] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 5.136717] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 5.141938] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 5.148028] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 5.154802] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff pref]
[ 5.161998] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 5.168850] pci 0000:02:00.0: [14c3:7915] type 00 class 0x000280
[ 5.174905] pci 0000:02:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[ 5.181930] pci 0000:02:00.0: reg 0x10: [mem size 0x00100000 64bit pref]
[ 5.188628] pci 0000:02:00.0: reg 0x18: initial BAR value 0x00000000 invalid
[ 5.195659] pci 0000:02:00.0: reg 0x18: [mem size 0x00004000 64bit pref]
[ 5.202344] pci 0000:02:00.0: reg 0x20: initial BAR value 0x00000000 invalid
[ 5.209374] pci 0000:02:00.0: reg 0x20: [mem size 0x00001000 64bit pref]
[ 5.216178] pci 0000:02:00.0: supports D1 D2
[ 5.220430] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 5.227069] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 5.243316] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 5.248540] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 5.254624] pci 0000:00:01.0: bridge window [mem 0x60000000-0x600fffff]
[ 5.261384] pci 0000:00:01.0: bridge window [mem 0x60000000-0x600fffff pref]
[ 5.268591] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 5.275240] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 5.281825] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 5.288780] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 5.295386] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 5.302322] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 5.309098] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref]
[ 5.316305] pci 0000:00:01.0: BAR 8: assigned [mem 0x60300000-0x603fffff]
[ 5.323064] pci 0000:00:01.0: BAR 9: assigned [mem 0x60400000-0x605fffff pref]
[ 5.330271] pci 0000:00:00.0: BAR 1: assigned [mem 0x60600000-0x6060ffff]
[ 5.337050] pci 0000:00:01.0: BAR 1: assigned [mem 0x60610000-0x6061ffff]
[ 5.343829] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff]
[ 5.350588] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff]
[ 5.357387] pci 0000:01:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref]
[ 5.365128] pci 0000:01:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref]
[ 5.372850] pci 0000:01:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref]
[ 5.380585] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 5.385544] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff]
[ 5.392304] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 5.399077] pci 0000:00:00.0: bridge window [mem 0x60100000-0x602fffff pref]
[ 5.406296] pci 0000:02:00.0: BAR 0: assigned [mem 0x60400000-0x604fffff 64bit pref]
[ 5.414041] pci 0000:02:00.0: BAR 2: assigned [mem 0x60500000-0x60503fff 64bit pref]
[ 5.421763] pci 0000:02:00.0: BAR 4: assigned [mem 0x60504000-0x60504fff 64bit pref]
[ 5.429497] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 5.434457] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff]
[ 5.441215] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff]
[ 5.447987] pci 0000:00:01.0: bridge window [mem 0x60400000-0x605fffff pref]
[ 5.472095] Freeing unused kernel memory: 4196K
[ 5.476711] This architecture does not have kernel memory protection.
[ 5.483170] Run /init as init process
[ 5.487198] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 5.940871] init: Console is alive
[ 5.944679] init: - watchdog -
[ 5.958859] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.972677] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.983645] init: - preinit -
[ 6.181346] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.260250] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.300334] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.551855] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 6.560288] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 6.563791] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 6.575686] 8021q: adding VLAN 0 to HW filter on device lan1
[ 6.583985] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 9.719087] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 9.726642] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready
[ 10.730962] mt7530 mdio-bus:1f lan1: Link is Down
[ 10.745737] procd: - early -
[ 10.748849] procd: - watchdog -
[ 11.303455] procd: - watchdog -
[ 11.307611] procd: - ubus -
[ 11.317817] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.363972] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.370791] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.380604] procd: - init -
Please press Enter to activate this console.
[ 11.734554] kmodloader: loading kernel modules from /etc/modules.d/*
[ 11.795122] PPP generic driver version 2.4.2
[ 11.800949] NET: Registered protocol family 24
[ 11.812638] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 11.965073] urngd: v1.0.2 started.
[ 12.138445] random: crng init done
[ 12.141845] random: 30 urandom warning(s) missed due to ratelimiting
[ 23.830501] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 23.852392] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 23.860668] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 23.866519] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 23.876380] 8021q: adding VLAN 0 to HW filter on device lan1
[ 23.885024] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 23.892258] br-lan: port 1(lan1) entered blocking state
[ 23.897639] br-lan: port 1(lan1) entered disabled state
[ 23.904893] device lan1 entered promiscuous mode
[ 23.909551] device eth0 entered promiscuous mode
[ 23.950567] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 23.957845] 8021q: adding VLAN 0 to HW filter on device lan2
[ 23.967032] br-lan: port 2(lan2) entered blocking state
[ 23.972321] br-lan: port 2(lan2) entered disabled state
[ 23.979200] device lan2 entered promiscuous mode
[ 23.998003] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 24.005385] 8021q: adding VLAN 0 to HW filter on device lan3
[ 24.015592] br-lan: port 3(lan3) entered blocking state
[ 24.020883] br-lan: port 3(lan3) entered disabled state
[ 24.027920] device lan3 entered promiscuous mode
[ 24.045690] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode
[ 24.052898] 8021q: adding VLAN 0 to HW filter on device lan4
[ 24.062233] br-lan: port 4(lan4) entered blocking state
[ 24.067964] br-lan: port 4(lan4) entered disabled state
[ 24.075046] device lan4 entered promiscuous mode
[ 24.104249] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode
[ 24.111444] 8021q: adding VLAN 0 to HW filter on device wan
[ 26.833969] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 26.841497] br-lan: port 1(lan1) entered blocking state
[ 26.846740] br-lan: port 1(lan1) entered forwarding state
[ 26.853229] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
with option 2 ?
@d687r02j8g @frollic bro, You two are doing so much for me. I am very grateful to both of you even if the problem is never solved. 
Doesn't work with snapshot either.
Try the image I uploaded with option 2. If this doesn't work then need to wait until the issue get resolved
Unless someone else has any ideas?
Did you flash this yet?
Maybe. I'm not sure though.
It isn't much work to get the chip you have working judging from the patch that was submitted. Just need a developer to look at it. Try the image I made first.
Let me share my experience on how I successfully flashing Openwrt firmware to my Totolink X5000R wireless router.
Firstly, you ought to make sure your router install with X5000R AX1800 WiFi 6 Giga wireless V9.1.0u.6118_B20201102 stock firmware. Others won’t allowed me to install any Openwrt onto it.
The rest is easy, download and install the Openwrt firmware via stock firmware GUI. There all it is.
@d687r02j8g bro, I am not at home today. So I can't check. When I return home I will check and let you know the output.
@Ethereal Bro , I can't go back to stock firmware either. I'm stuck at "system running in (initramfs)recovery mode." 
Assuming @Ethereal have an X5000R up and running with OpenWRT, he should be able to dump the required partition(s) from his device to file(s), so you can write them to your router from the initramfs.
The issue with op is that his router has a new flash chip that isn't supported by openwrt yet. So even with a flash dump, his device prolly won't work with openwrt. Hopefully the patched image should work for op.
It's midnight here, I'm willing to lend a hand if I could.
Since I am new to Openwrt, may I ask how to "dump the required partition(s) from his device to file(s)"?
Are you referring to partition of rootfs and rootfs_data?
How sensitive it is if I share this information with others?
Please enlighten me. At least, an attempt to revive the op's router.
If you are flashing to my compiled image, you need to flash it using totolink's built in firmware updater. Using initramfs version of the OpenWRT to flash would not stick.
Here is a screenshot of my current router running 22.03.5 with my compiled image.
I can reflash again to make sure it works. I'll keep you updated.
Edit: I had 22.03.3 working with my fork and I just upgraded to my own compiled images after every major release. I will test the 22.03.5 image flash from totolink stock image in the next 24 hours.
Please flash my compiled https://github.com/ThranduilII/openwrt/files/11399622/Openwrt-22.03.5-X5000R-Zbit-support.zip through totolink's image upgrade web interface.
This should be the firmware version: OpenWrt 22.03.5 r20134-5f15225c1e / LuCI openwrt-22.03 branch git-23.093.57104-ce20b4a
I will be compiling 22.03.3 and 22.03.4 images in case 22.03.5 isn't working for everyone.
@wopo bro, I followed your instructions exactly and flashed it using the sysupgrade.bin image downloaded from the link you provided.Unfortunately I still see "System running in recovery (initramfs) mode". I have attached a picture. What the storage is showing here doesn't look normal to me. Please check if it is ok.Thanks for your guidance. Awaiting further instructions.
Since you got serial, attach the output from it with every flash attempt.
@frollic bro, here is the output which I got by following the instructions of @wopo bro...
Request for: /
Request for: /style.css
Request for: /favicon.ico
## Error: file not found!
Data will be downloaded at 0x88000000 in RAM
Upgrade type: firmware
Upload file size: 7865406 bytes
Loading: #######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
#######################################
########################
HTTP upload is done! Upgrading...
****************************
* FIRMWARE UPGRADING *
* DO NOT POWER OFF DEVICE! *
****************************
upfile len = 0x78043e
regulation: http recover system need erase nvram config sector!
raspi_erase: offs:30000 len:10000
.
orig web erase+write
Abort: image size larger than 2097152!
HTTP ugrade is done! Rebooting...
===================================================================
MT7621 stage1 code 10:33:55 (ASIC)
CPU=500000000 HZ BUS=166666666 HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x11100000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-1200Mhz ===
PLL3 FB_DL: 0xa, 1/0 = 673/351 29000000
PLL4 FB_DL: 0xf, 1/0 = 618/406 3D000000
PLL2 FB_DL: 0x10, 1/0 = 534/490 41000000
do DDR setting..[01F40000]
Apply DDR3 Setting...(use customer AC)
0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120
--------------------------------------------------------------------------------
0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000E:| 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1
000F:| 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0
0010:| 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0
0011:| 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
rank 0 coarse = 16
rank 0 fine = 40
B:| 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0
opt_dle value:11
DRAMC_R0DELDLY[018]=00002120
==================================================================
RX DQS perbit delay software calibration
==================================================================
1.0-15 bit dq delay value
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 10 9 10 11 9 9 10 8 8 9
10 | 10 11 9 11 9 11
--------------------------------------
==================================================================
2.dqs window
x=pass dqs delay value (min~max)center
y=0-7bit DQ of every group
input delay:DQS0 =32 DQS1 = 33
==================================================================
bit DQS0 bit DQS1
0 (1~60)30 8 (1~62)31
1 (1~62)31 9 (2~61)31
2 (1~60)30 10 (2~64)33
3 (1~62)31 11 (1~60)30
4 (1~61)31 12 (1~61)31
5 (1~62)31 13 (0~60)30
6 (1~60)30 14 (1~63)32
7 (1~63)32 15 (1~62)31
==================================================================
3.dq delay value last
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 12 10 12 12 10 10 12 8 10 11
10 | 10 14 11 14 10 13
==================================================================
==================================================================
TX perbyte calibration
==================================================================
DQS loop = 15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1
dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2
DQ loop=15, cmp_err_1 = ffff0080
dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=1
DQ loop=14, cmp_err_1 = ffff0080
DQ loop=13, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=13, finish count=2
byte:0, (DQS,DQ)=(9,8)
byte:1, (DQS,DQ)=(8,8)
20,data:89
[EMI] DRAMC calibration passed
===================================================================
MT7621 stage1 code done
CPU=500000000 HZ BUS=166666666 HZ
===================================================================
U-Boot 1.1.3 (Jun 29 2020 - 14:15:59)
Board: Ralink APSoC DRAM: 256 MB
mtk gpio init : BTN_RST pin 4.
Config XHCI 40M PLL
******************************
Software System Reset Occurred
******************************
flash manufacture id: 5e, device id 40 18
Warning: un-recognized chip ID, please update bootloader!
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 5.0.3.0-256
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: SPI Flash
Date:Jun 29 2020 Time:14:15:59
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size = 256 Mbytes
#Reset_MT7530
#Turn on MT7530 LED
set LAN/WAN LLLLW
Press press RST button for more than 2 seconds to run web failsafe mode
RST button is pressed for: 0 second(s)
Catution: RST button wasn't pressed or not long enough!
Continuing normal boot...
Waitting for network init complete : 1
regValue=[0x0]
Port3 Link DOWN!
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
6: Load Flash code then burn to Flash via TFTP.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3 0
3: System Boot system code via Flash.
## Booting image at bfc50000 ...
Image Name: C8343R-9999
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 5763479 Bytes = 5.5 MB
Load Address: 80001000
Entry Point: 80001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 256
Starting kernel ...
[ 0.000000] Linux version 5.10.176 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r20134-5f15225c1e) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Thu Apr 27 20:28:15 2023
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is TOTOLINK X5000R
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] percpu: Embedded 15 pages/cpu s30480 r8192 d22768 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Writing ErrCtl register=00004000
[ 0.000000] Readback ErrCtl register=00004000
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 246356K/262144K available (7064K kernel code, 631K rwdata, 832K rodata, 4196K init, 243K bss, 15788K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000012] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.007942] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.017006] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)