Your more than welcome, here is the firewall zone that covers my VPN interfaces. I forgot that I renamed them but should work the same regardless.
In the VPN Policy based routing instructions it does imply that you should have a separate zone for each VPN interface but I have had this setup like this for a while now with no issues.
Is there a place where I can download previous firmware releases?
Bottom of the home page
I have been visiting this page for a few years now. How did I not notice this link? 
Thank you
New update for Marvell router wrt1900acs v2 !
Firmware version: 2.0.3.201002
Release date: May 1, 2020
I'm with a WRT3200ACM, and the 04/26 build makes the wifi unusable: some phantom thing clogs up the traffic. If I connect to the router through it's LAN ports the speedtest is fine. I removed all wifi clients (quite a few). Everything was off and the wifi showed 60-100 Mbit traffic (Graphs -> Wireless -> ...). Does anyone experience the same? The router's CPU utilization didn't go over 3-5% though. I cannot understand this. I'll try to revert back to the earlier firmware.
Do you have a link?
Being a little more specific: by 04/26 build I meant r13059. Now I reverted back to r12833, and the wifi speed is usable, but something is not quite right: it's still heavily bogged down. I stopped now smbd (this is a pure wifi router, no shares) and also ddns (also don't use it). I also discovered that adblock was errorring, and I force reinstalled it, that wiped the config file and now it's OK. Now a little more detail about this "bog down situation".
tcpdump -i wlan0 -l -U -s0 -n -q -c 500 or tcpdump -i wlan1 -l -U -s0 -n -q -c 500 should have filled the dump file in a blink of an eye if there's 25Mbps traffic. However, the dump lasted several seconds, and it showed completely boring stuff, nothing what I expected that 1.5K packets hauled around. So I'm absolutely dumbfounded. WTF is going on?Real-time graphs:
Statistic graphs:
Other:
Once more: that massive 25Mbps traffic is in one hand phantom (because even tcpdump couldn't catch anything and CPU is not bogged) but on the other hand real because the speedtest really measures that 50-60Mbps lost bandwidth (if I maybe sum the wlan0 5G and the wlan1 2.4G phantom traffic it comes out to about 50 Mbps) if I compare it to the LAN connection.
Do you know how bad this change is for us with Armada 385? What use cases are relevant? That OpenWRT Dev said in his answer it makes no performance loss, but I doubt that. I mean it just uses half of the CPUs registers now, no? For the FPU unit at least, not sure how important that is I am not a CPU expert. But it sounds significant. What about something like OpenVPN bandwidth?
What kind of CLIENT do you have?
As reported 4 days ago, I have experienced the same! My Wifi was unstable and the network speed slow. Reverted to the previous build. Also using a WRT3200ACM.
Interesting, much like the WRT3200ACM a few months ago, it seems Linksys is updating these routers for the first time in over 2 years.
So, really enjoying the DNSCryprt-proxyV2 operation these days, with some exceptions.
Due to the randomization of resolver servers, and the fact that international servers can be used, we are encountering random security alerts from various providers : "suspicious login from (not USA) detected, was this you?".. or random rejections from various content or streaming sites due to region restrictions. "access to context X (USA) is not allowed from (random country)."
Anyone else seeing this? Maybe I need to specify only a set of USA based servers to avoid this? Probably solves the content issue, but not the "suspicious login" if a server outside of my regional area is chosen.
I'm having the same issue at times. Are you running Firefox by any chance. They just started to roll out a version of DNS Cryprt in Firefox 76.0 using Cloudflare. It can be turned off in Firefox preferences, network settings, bottom of the page. Seems like this started when Firefox was updated to 76.0.
Thing is will they update the WRT32X v1 or the WRT32XB. As you have pointed out the WRT3200ACM and now the WRT1900ACS v2 has got updates, so hopefully the WRT32X will.
Hi Gremlin,
So i have tried what youve said, but not sure of the ifdev config you mentioned in the earlier post. Here is how my client file looks like.
dev ovpnc1
dev-type tun
ns-cert-type server
setenv opt tls-version-min 1.0 or-highest
reneg-sec 604800
sndbuf 0
rcvbuf 0
At he moment only one vpn is working, however I have managed to add ovpnc1 to an instance but it doesnt seem to be receiving any packets
I also get this in policybasedrouting
wan/pppoe-wan/125.235.249.188 ✓
LinodeVPN/opvnc0/172.27.232.29
aws/ovpnc1/0.0.0.0
