Connection returned : "Call failed"

[soonerdolfan]

I am brand new and understand little of this. I've been searching on here for a few hours and started getting more and more confused. I'm sure it's because I was reading posts with my keywords but not identical to my situation. It's very hard for me to ask for help but I am starting to get desperate. I will post as much information as I think you'll need and if someone can point me where to start reading I won't bother anyone.

Equipment:
WE826-T2 Used as the access point (I think it's called)
Powered by LuCI open wrt - 18.06 branch (git - 18.228.31946-f64b152) / GoldenOrb_2019-03-06

TP-Link Archer A7(US) (connected to the WE826-T2 in the Lan1 port) (to use as the wireless network)
4 TP-Link AC750 (for the wireless mesh inside the house) (connected to the Archer A-7)
TP-Link 5 port fast ethernet switch (connected to the Archer A7 lan port) (conneected to 3 PC's and a TV)
Provider
AT&T 4g LTE unlimited

I got the modem a couple months ago. It had a few instructions on a business card on how to set it up. I also got an email from another sight on how to set it up using the AT&T 4g lte unlimited iPad plan. I followed the instructions on the email and it worked. I was ecstatic,shocked and amazed. After having to deal with Hughesnet for the past 3 years I literally cried, but enough about that. As I went along I added and connected the equipment above with no issues, until yesterday. All the sudden we had no internet. I rebooted the modem (we826) about a hundred times it seems. Started researching and found out how to do a 30/30/30 reset and did it. I've disconnected everything and connected my PC to a single LAN1 port on the we826. After getting confused I decided to start at the beginning and read the setup guide. I changed the ip address to 192.168.2.1, cleared my cache on my browser but can't seem to get back into the LuCI gui. So now I sit here typing heartbroken and desperate. I will insert what I have below.

kernell Log

 0.000000] Linux version 4.14.63 (dairyman@Compaq-Pro-6300) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7258-5eb055306f)) #0 Thu Aug 16 07:51:15 2018
[    0.000000] Board has DDR2
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[    0.000000] MIPS: machine is ZBT-WE826 (16M)
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] On node 0 totalpages: 32768
[    0.000000] free_area_init_node: node 0, pgdat 8044aae0, node_mem_map 81000040
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] random: get_random_bytes called from start_kernel+0x8c/0x474 with crng_init=0
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=0006cfa1
[    0.000000] Readback ErrCtl register=0006cfa1
[    0.000000] Memory: 125016K/131072K available (3400K kernel code, 175K rwdata, 824K rodata, 200K init, 216K bss, 6056K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 256
[    0.000000] CPU Clock: 580MHz
[    0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[    0.000000] systick: enable autosleep mode
[    0.000000] systick: running - mult: 214748, shift: 32
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[    0.000013] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[    0.007589] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.073545] pid_max: default: 32768 minimum: 301
[    0.078261] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.084641] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.097444] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.106981] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.112969] pinctrl core: initialized pinctrl subsystem
[    0.118576] NET: Registered protocol family 16
[    0.606909] mt7620-pci 10140000.pcie: PCIE0 no card, disable it(RST&CLK)
[    0.613405] mt7620-pci: probe of 10140000.pcie failed with error -1
[    0.636110] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.641506] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.647921] rt2880_gpio 10000638.gpio: registering 16 gpios
[    0.653294] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[    0.659667] rt2880_gpio 10000688.gpio: registering 1 gpios
[    0.664957] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[    0.675431] clocksource: Switched to clocksource systick
[    0.681846] NET: Registered protocol family 2
[    0.686938] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.693665] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.699884] TCP: Hash tables configured (established 1024 bind 1024)
[    0.706162] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.711786] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.718188] NET: Registered protocol family 1
[    0.722380] PCI: CLS 0 bytes, default 32
[    0.724975] rt-timer 10000100.timer: maximum frequency is 1220Hz
[    0.731665] Crashlog allocated RAM at address 0x3f00000
[    0.738336] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.750271] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.755918] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.774710] io scheduler noop registered
[    0.778515] io scheduler deadline registered (default)
[    0.784411] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.791725] console [ttyS0] disabled
[    0.795177] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[    0.804849] console [ttyS0] enabled
[    0.811878] bootconsole [early0] disabled
[    0.820602] cacheinfo: Failed to find cpu0 device node
[    0.825888] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    0.836699] spi spi0.0: force spi mode3
[    0.850036] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    0.854890] 4 fixed-partitions partitions found on MTD device spi0.0
[    0.861392] Creating 4 MTD partitions on "spi0.0":
[    0.866296] 0x000000000000-0x000000030000 : "u-boot"
[    0.872282] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.878656] 0x000000040000-0x000000050000 : "factory"
[    0.884664] 0x000000050000-0x000001000000 : "firmware"
[    2.695412] random: fast init done
[    2.794483] 2 uimage-fw partitions found on MTD device firmware
[    2.800555] 0x000000050000-0x0000001b8e8c : "kernel"
[    2.806567] 0x0000001b8e8c-0x000001000000 : "rootfs"
[    2.812419] mtd: device 5 (rootfs) set to be root filesystem
[    2.819696] 1 squashfs-split partitions found on MTD device rootfs
[    2.826078] 0x0000007fc000-0x000001000000 : "rootfs_data"
[    2.833296] libphy: Fixed MDIO Bus: probed
[    2.842158] gsw: setting port4 to ephy mode
[    2.846512] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 3 link up (100Mbps/Full duplex)
[    2.856067] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[    2.862784] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[    2.871801] rt2880_wdt 10000120.watchdog: Initialized
[    2.878330] NET: Registered protocol family 10
[    2.886718] Segment Routing with IPv6
[    2.890585] NET: Registered protocol family 17
[    2.895165] 8021q: 802.1Q VLAN Support v1.8
[    2.917244] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    2.925589] Freeing unused kernel memory: 200K
[    2.930121] This architecture does not have kernel memory protection.
[    4.659696] init: Console is alive
[    4.663393] init: - watchdog -
[    8.771812] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    9.185817] usbcore: registered new interface driver usbfs
[    9.191564] usbcore: registered new interface driver hub
[    9.197137] usbcore: registered new device driver usb
[    9.208510] exFAT: Version 1.2.9
[    9.245637] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    9.261669] SCSI subsystem initialized
[    9.271083] ehci-platform: EHCI generic platform driver
[    9.286824] phy phy-usbphy.0: remote usb device wakeup disabled
[    9.292871] phy phy-usbphy.0: UTMI 16bit 30MHz
[    9.297440] ehci-platform 101c0000.ehci: EHCI Host Controller
[    9.303337] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[    9.311555] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[    9.327533] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[    9.334950] hub 1-0:1.0: USB hub found
[    9.339233] hub 1-0:1.0: 1 port detected
[    9.346931] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    9.355185] ohci-platform: OHCI generic platform driver
[    9.360891] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[    9.367896] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[    9.376062] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[    9.409593] hub 2-0:1.0: USB hub found
[    9.413878] hub 2-0:1.0: 1 port detected
[    9.421148] uhci_hcd: USB Universal Host Controller Interface driver
[    9.441319] MTK MSDC device init.
[    9.465710] mtk-sd: MediaTek MT6575 MSDC Driver
[    9.475855] usbcore: registered new interface driver usb-storage
[    9.485763] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    9.497489] init: - preinit -
[    9.620131] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    9.960318] hub 1-1:1.0: USB hub found
[    9.965610] hub 1-1:1.0: 4 ports detected
[   10.740104] usb 1-1.3: new full-speed USB device number 3 using ehci-platform
[   10.964373] usb 1-1.3: new high-speed USB device number 4 using ehci-platform
[   11.545392] random: procd: uninitialized urandom read (4 bytes read)
[   11.557825] 8021q: adding VLAN 0 to HW filter on device eth0
[   12.889232] mount_root: loading kmods from internal overlay
[   12.959278] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   12.968712] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   16.547181] jffs2: notice: (410) jffs2_build_xattr_subsystem: complete building xattr subsystem, 6 of xdatum (0 unchecked, 6 orphan) and 30 of xref (6 dead, 24 orphan) found.
[   16.564113] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   16.571485] block: unable to load configuration (fstab: Entry not found)
[   16.578496] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[   16.585121] block: unable to load configuration (fstab: Entry not found)
[   16.592108] block: attempting to load /etc/config/fstab
[   16.603366] block: unable to load configuration (fstab: Entry not found)
[   16.610393] block: no usable configuration
[   17.815652] jffs2: notice: (408) jffs2_build_xattr_subsystem: complete building xattr subsystem, 6 of xdatum (0 unchecked, 6 orphan) and 30 of xref (6 dead, 24 orphan) found.
[   19.570395] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   19.577748] block: unable to load configuration (fstab: Entry not found)
[   19.584677] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[   19.591468] block: unable to load configuration (fstab: Entry not found)
[   19.598471] block: attempting to load /etc/config/fstab
[   19.603930] block: unable to load configuration (fstab: Entry not found)
[   19.610895] block: no usable configuration
[   19.616782] mount_root: overlay filesystem has not been fully initialized yet
[   19.628979] mount_root: switching to jffs2 overlay
[   19.695392] overlayfs: upper fs does not support tmpfile.
[   19.710771] urandom-seed: Seed file not found (/etc/urandom.seed)
[   20.005439] procd: - early -
[   20.009334] procd: - watchdog -
[   20.714729] procd: - watchdog -
[   20.719395] procd: - ubus -
[   21.412039] random: ubusd: uninitialized urandom read (4 bytes read)
[   21.637586] random: ubusd: uninitialized urandom read (4 bytes read)
[   21.811984] random: ubusd: uninitialized urandom read (4 bytes read)
[   22.623371] random: ubusd: uninitialized urandom read (4 bytes read)
[   22.637986] random: ubusd: uninitialized urandom read (4 bytes read)
[   22.644541] random: ubusd: uninitialized urandom read (4 bytes read)
[   22.667297] procd: - init -
[   23.284369] kmodloader: loading kernel modules from /etc/modules.d/*
[   23.430600] tun: Universal TUN/TAP device driver, 1.6
[   23.459285] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   23.486369] Netfilter messages via NETLINK v0.30.
[   23.572624] ip_set: protocol 6
[   23.628975] u32 classifier
[   23.631749]     input device check on
[   23.635478]     Actions configured
[   23.642144] Mirror/redirect action on
[   23.659957] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   23.700608] fuse init (API version 7.26)
[   23.725682] usbcore: registered new interface driver cdc_wdm
[   23.746512] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[   23.754754] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[   23.785859] ip_tables: (C) 2000-2006 Netfilter Core Team
[   23.810650] ctnetlink v0.93: registering with nfnetlink.
[   23.986404] usbcore: registered new interface driver usblp
[   24.106937] usbcore: registered new interface driver usbserial
[   24.113091] usbcore: registered new interface driver usbserial_generic
[   24.119897] usbserial: USB Serial support registered for generic
[   24.171530] xt_time: kernel timezone is -0000
[   24.179325] usbcore: registered new interface driver cdc_ether
[   24.190379] usbcore: registered new interface driver cdc_ncm
[   24.349168] usbcore: registered new interface driver huawei_cdc_ncm
[   24.501418] PPP generic driver version 2.4.2
[   24.509206] NET: Registered protocol family 24
[   24.518703] qmi_wwan 1-1.3:1.4: cdc-wdm0: USB WDM device
[   24.526576] qmi_wwan 1-1.3:1.4 wwan0: register 'qmi_wwan' at usb-101c0000.ehci-1.3, WWAN/QMI device, ba:fc:9e:7d:c7:03
[   24.537867] usbcore: registered new interface driver qmi_wwan
[   24.560422] usbcore: registered new interface driver rndis_host
[   24.628909] usbcore: registered new interface driver sierra
[   24.634705] usbserial: USB Serial support registered for Sierra USB modem
[   24.651114] usbcore: registered new interface driver sierra_net
[   24.683374] usbcore: registered new interface driver cdc_mbim
[   24.696722] usbcore: registered new interface driver option
[   24.702636] usbserial: USB Serial support registered for GSM modem (1-port)
[   24.710472] option 1-1.3:1.0: GSM modem (1-port) converter detected
[   24.717172] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB0
[   24.724750] option 1-1.3:1.1: GSM modem (1-port) converter detected
[   24.731530] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB1
[   24.739099] option 1-1.3:1.2: GSM modem (1-port) converter detected
[   24.745804] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB2
[   24.753383] option 1-1.3:1.3: GSM modem (1-port) converter detected
[   24.760141] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB3
[   24.898861] usbcore: registered new interface driver qcserial
[   24.904888] usbserial: USB Serial support registered for Qualcomm USB modem
[   24.985258] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[   24.992715] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[   25.000640] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[   25.008386] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   25.050356] usbcore: registered new interface driver rt2800usb
[   25.057514] kmodloader: done loading kernel modules from /etc/modules.d/*
[   45.213603] 8021q: adding VLAN 0 to HW filter on device eth0
[   45.254666] br-lan: port 1(eth0.1) entered blocking state
[   45.260264] br-lan: port 1(eth0.1) entered disabled state
[   45.266159] device eth0.1 entered promiscuous mode
[   45.271238] device eth0 entered promiscuous mode
[   45.439813] br-lan: port 1(eth0.1) entered blocking state
[   45.445341] br-lan: port 1(eth0.1) entered forwarding state
[   45.451468] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   46.522677] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   57.740787] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   57.751725] br-lan: port 2(wlan0) entered blocking state
[   57.757162] br-lan: port 2(wlan0) entered disabled state
[   57.763044] device wlan0 entered promiscuous mode
[   57.768088] br-lan: port 2(wlan0) entered blocking state
[   57.773516] br-lan: port 2(wlan0) entered forwarding state
[   61.079428] ieee80211 phy0: rt2800_config_txpower_rt6352: Warning - ignoring EEPROM HT40 power delta: -2
[   62.004684] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   63.544958] br-lan: port 2(wlan0) entered disabled state
[   63.550561] br-lan: port 1(eth0.1) entered disabled state
[   63.688081] device eth0.1 left promiscuous mode
[   63.692908] br-lan: port 1(eth0.1) entered disabled state
[   63.741316] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[   64.099259] device wlan0 left promiscuous mode
[   64.103946] br-lan: port 2(wlan0) entered disabled state
[   64.801747] device eth0 left promiscuous mode
[   75.920575] 8021q: adding VLAN 0 to HW filter on device eth0
[   75.958568] br-lan: port 1(eth0.1) entered blocking state
[   75.964095] br-lan: port 1(eth0.1) entered disabled state
[   75.970056] device eth0.1 entered promiscuous mode
[   75.974952] device eth0 entered promiscuous mode
[   76.043109] br-lan: port 1(eth0.1) entered blocking state
[   76.048696] br-lan: port 1(eth0.1) entered forwarding state
[   76.054599] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   76.957637] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   81.163047] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   81.211445] br-lan: port 2(wlan0) entered blocking state
[   81.216883] br-lan: port 2(wlan0) entered disabled state
[   81.222781] device wlan0 entered promiscuous mode
[   84.667631] ieee80211 phy0: rt2800_config_txpower_rt6352: Warning - ignoring EEPROM HT40 power delta: -2
[   84.719040] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   84.725751] br-lan: port 2(wlan0) entered blocking state
[   84.731252] br-lan: port 2(wlan0) entered forwarding state
[   92.587308] random: crng init done
[   92.590801] random: 3 urandom warning(s) missed due to ratelimiting
[   96.521709] device wlan0 left promiscuous mode
[   96.526384] br-lan: port 2(wlan0) entered disabled state
[   97.034563] br-lan: port 1(eth0.1) entered disabled state
[   97.069953] device eth0.1 left promiscuous mode
[   97.074789] br-lan: port 1(eth0.1) entered disabled state
[   97.118392] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[   97.944988] device eth0 left promiscuous mode
[  107.749955] 8021q: adding VLAN 0 to HW filter on device eth0
[  107.783029] br-lan: port 1(eth0.1) entered blocking state
[  107.788627] br-lan: port 1(eth0.1) entered disabled state
[  107.794521] device eth0.1 entered promiscuous mode
[  107.799473] device eth0 entered promiscuous mode
[  107.869068] br-lan: port 1(eth0.1) entered blocking state
[  107.874594] br-lan: port 1(eth0.1) entered forwarding state
[  107.880558] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[  108.797430] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[  112.489390] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  112.530985] br-lan: port 2(wlan0) entered blocking state
[  112.536422] br-lan: port 2(wlan0) entered disabled state
[  112.542318] device wlan0 entered promiscuous mode
[  115.217298] ieee80211 phy0: rt2800_config_txpower_rt6352: Warning - ignoring EEPROM HT40 power delta: -2
[  115.263531] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  115.270304] br-lan: port 2(wlan0) entered blocking state
[  115.275731] br-lan: port 2(wlan0) entered forwarding state
[  583.668127] usb 1-1.3: USB disconnect, device number 4
[  583.673835] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[  583.682200] option 1-1.3:1.0: device disconnected
[  583.687544] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[  583.695924] option 1-1.3:1.1: device disconnected
[  583.701342] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[  583.709712] option 1-1.3:1.2: device disconnected
[  583.715056] option1 ttyUSB3: GSM modem (1-port) converter now disconnected from ttyUSB3
[  583.723506] option 1-1.3:1.3: device disconnected
[  583.728705] qmi_wwan 1-1.3:1.4 wwan0: unregister 'qmi_wwan' usb-101c0000.ehci-1.3, WWAN/QMI device
[  592.787071] usb 1-1.3: new high-speed USB device number 5 using ehci-platform
[  592.970813] option 1-1.3:1.0: GSM modem (1-port) converter detected
[  592.977628] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB0
[  592.985651] option 1-1.3:1.1: GSM modem (1-port) converter detected
[  592.992431] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB1
[  593.000520] option 1-1.3:1.2: GSM modem (1-port) converter detected
[  593.007382] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB2
[  593.015447] option 1-1.3:1.3: GSM modem (1-port) converter detected
[  593.022215] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB3
[  593.135555] qmi_wwan 1-1.3:1.4: cdc-wdm0: USB WDM device
[  593.150079] qmi_wwan 1-1.3:1.4 wwan0: register 'qmi_wwan' at usb-101c0000.ehci-1.3, WWAN/QMI device, ba:fc:9e:7d:c7:03
[  922.877621] usb 1-1.3: USB disconnect, device number 5
[  922.883321] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[  922.891711] option 1-1.3:1.0: device disconnected
[  922.897115] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[  922.905436] option 1-1.3:1.1: device disconnected
[  922.910839] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[  922.919221] option 1-1.3:1.2: device disconnected
[  922.924577] option1 ttyUSB3: GSM modem (1-port) converter now disconnected from ttyUSB3
[  922.933026] option 1-1.3:1.3: device disconnected
[  923.067832] qmi_wwan 1-1.3:1.4 wwan0: unregister 'qmi_wwan' usb-101c0000.ehci-1.3, WWAN/QMI device
[  931.709253] usb 1-1.3: new high-speed USB device number 6 using ehci-platform
[  931.772789] option 1-1.3:1.0: GSM modem (1-port) converter detected
[  931.779584] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB0
[  931.787683] option 1-1.3:1.1: GSM modem (1-port) converter detected
[  931.794506] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB1
[  931.802610] option 1-1.3:1.2: GSM modem (1-port) converter detected
[  931.809366] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB2
[  931.817384] option 1-1.3:1.3: GSM modem (1-port) converter detected
[  931.824155] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB3
[  931.899350] qmi_wwan 1-1.3:1.4: cdc-wdm0: USB WDM device
[  931.907237] qmi_wwan 1-1.3:1.4 wwan0: register 'qmi_wwan' at usb-101c0000.ehci-1.3, WWAN/QMI device, ba:fc:9e:7d:c7:03
[ 1531.770349] usb 1-1.3: USB disconnect, device number 6
[ 1531.776088] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 1531.784458] option 1-1.3:1.0: device disconnected
[ 1531.789805] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 1531.798199] option 1-1.3:1.1: device disconnected
[ 1531.803603] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 1531.811965] option 1-1.3:1.2: device disconnected
[ 1531.817329] option1 ttyUSB3: GSM modem (1-port) converter now disconnected from ttyUSB3
[ 1531.825764] option 1-1.3:1.3: device disconnected
[ 1531.830958] qmi_wwan 1-1.3:1.4 wwan0: unregister 'qmi_wwan' usb-101c0000.ehci-1.3, WWAN/QMI device
[ 1540.683384] usb 1-1.3: new high-speed USB device number 7 using ehci-platform
[ 1540.745808] option 1-1.3:1.0: GSM modem (1-port) converter detected
[ 1540.752604] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB0
[ 1540.760737] option 1-1.3:1.1: GSM modem (1-port) converter detected
[ 1540.767530] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB1
[ 1540.775628] option 1-1.3:1.2: GSM modem (1-port) converter detected
[ 1540.782390] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB2
[ 1540.790399] option 1-1.3:1.3: GSM modem (1-port) converter detected
[ 1540.797165] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB3
[ 1540.872356] qmi_wwan 1-1.3:1.4: cdc-wdm0: USB WDM device
[ 1540.880186] qmi_wwan 1-1.3:1.4 wwan0: register 'qmi_wwan' at usb-101c0000.ehci-1.3, WWAN/QMI device, ba:fc:9e:7d:c7:03

system log

Thu Aug 16 08:25:44 2018 user.notice QMI Connect: Starting network NIL
Thu Aug 16 08:25:44 2018 user.notice QMI Connect: Connection returned : "Call failed"
Thu Aug 16 08:25:44 2018 user.notice QMI Connect: status is "disconnected"
Thu Aug 16 08:25:44 2018 user.notice QMI Connect: GET-CURRENT-SETTINGS is "Out of call"
Thu Aug 16 08:25:54 2018 user.notice Create Connection: Retry Connection
Thu Aug 16 08:26:05 2018 user.notice Create Connection: Pincode in script
Thu Aug 16 08:26:05 2018 user.notice Create Connection: Attempting to Connect
Thu Aug 16 08:26:19 2018 user.notice QMI Connect: WDA-GET-DATA-FORMAT is "raw-ip"
Thu Aug 16 08:26:20 2018 user.notice QMI Connect: Waiting for network registration
Thu Aug 16 08:26:20 2018 user.notice QMI Connect: Starting network NIL
Thu Aug 16 08:26:20 2018 user.notice QMI Connect: Connection returned : "Call failed"
Thu Aug 16 08:26:20 2018 user.notice QMI Connect: status is "disconnected"
Thu Aug 16 08:26:20 2018 user.notice QMI Connect: GET-CURRENT-SETTINGS is "Out of call"
Thu Aug 16 08:26:30 2018 user.notice Create Connection: Retry Connection
Thu Aug 16 08:26:42 2018 user.notice Create Connection: Pincode in script
Thu Aug 16 08:26:42 2018 user.notice Create Connection: Attempting to Connect
Thu Aug 16 08:26:55 2018 user.notice QMI Connect: WDA-GET-DATA-FORMAT is "raw-ip"
Thu Aug 16 08:26:56 2018 user.notice QMI Connect: Waiting for network registration
Thu Aug 16 08:26:57 2018 user.notice QMI Connect: Starting network NIL
Thu Aug 16 08:26:57 2018 user.notice QMI Connect: Connection returned : "Call failed"
Thu Aug 16 08:26:57 2018 user.notice QMI Connect: status is "disconnected"
Thu Aug 16 08:26:57 2018 user.notice QMI Connect: GET-CURRENT-SETTINGS is "Out of call"

(there's more but it just seems to repeat)

I'm adding pics I took when I needed to remember something.
OK nvm apparently they are too big and I need to add them to a cloud device, I will try and figure that out on my phone and edit my post, I am currently using it hot spotted to my pc.

Thank you to anyone who responds, Truly Thank You

[trendy]

The 30-30-30 is not necessary from what I can see in the device page.
Nor was it necessary to erase the whole device, rather than troubleshoot to find the problem, since it used to work fine.
Do you have a backup from when it was working properly?

[soonerdolfan]

No unfortunately I was dumb and did not do one, But I did back it up before the reset.

[trendy]

That will do, since the problem was not necessarily from your end.
Restore that and paste here in preformatted text (the </> button) the following:

uci export network; uci export dhcp; uci export firewall; \
head -n -0 /etc/firewall.user; \
iptables-save -c; ip6tables-save -c; \
ip -4 addr ; ip -4 ro ls tab all ; ip -4 ru; \
ip -6 addr ; ip -6 ro ls tab all ; ip -6 ru; \
ls -l  /etc/resolv.* /tmp/resolv.*; head -n -0 /etc/resolv.* /tmp/resolv.*

You can omit the ip6tables and ip -6 commands if you don't use IPv6.

[soonerdolfan]

@trendy

That will do, since the problem was not necessarily from your end.
Restore that and paste here in preformatted text (the </> button) the following:

Ok, it will take a bit I think. Still having problems getting into the gui. I think maybe because I'm hotspotted to my phone.

[trendy]

Take your time.

[soonerdolfan]

I’ve moved the hot spot to my iPad and I’m disabling the WiFi adapter and clearing my cache. I’m uploading the archive now. I think I learned something doing all that reading. Lol

[soonerdolfan]

while I'm finding what you wanted I realized I forgot to include the debug log. I do'nt know if you need it but here it is.

Tue Mar 17 07:47:43 2020 : /dev/ttyUSB2 AT+CPMS="SM"
+CPMS: 0,30,0,30,0,30
OK

Tue Mar 17 07:47:53 2020 : /dev/ttyUSB2 AT+COPS=0
OK

Tue Mar 17 07:47:54 2020 : /dev/ttyUSB2 AT+CGDCONT=?
+CGDCONT: (1-24,100-179),"IP",,,(0-2),(0-4),(0-1),(0-1)
+CGDCONT: (1-24,100-179),"PPP",,,(0-2),(0-4),(0-1),(0-1)
+CGDCONT: (1-24,100-179),"IPV6",,,(0-2),(0-4),(0-1),(0-1)
+CGDCONT: (1-24,100-179),"IPV4V6",,,(0-2),(0-4),(0-1),(0-1)
OK

Tue Mar 17 07:47:56 2020 : /dev/ttyUSB2 AT+CGDCONT?;+CFUN?
+CGDCONT: 1,"IPV4V6","broadband","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0
+CGDCONT: 2,"IPV4V6","ims","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0
+CGDCONT: 3,"IPV4V6","sos","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,1
+CFUN: 1
OK

Tue Mar 17 07:48:03 2020 : /dev/ttyUSB2 AT+CPMS="SM"
+CPMS: 0,30,0,30,0,30
OK

[soonerdolfan]

@trendy

uci export network; uci export dhcp; uci export firewall; \ head -n -0 /etc/firewall.user; \ iptables-save -c; ip6tables-save -c; \ ip -4 addr ; ip -4 ro ls tab all ; ip -4 ru; \ ip -6 addr ; ip -6 ro ls tab all ; ip -6 ru; \ ls -l /etc/resolv.* /tmp/resolv.; head -n -0 /etc/resolv. /tmp/resolv.*

I'm so sorry but where do I find these?

[trendy]

Connect with SSH first and paste the whole block there.
You can remove sensitive date, like username/passwords, cover mac addresses

[mk24]

I think that 'call failed' means that there is no signal received from the cell tower or that AT&T rejected your connection. The latter case could be because you're using an iPad plan in another device-- they can tell that.

Usual advice is to connect the modem to a laptop or desktop computer and make sure it can reach the Internet from there. Then examine the settings and logs of that computer to see which drivers are in use.

[soonerdolfan]

Preformatted textconfig interface 'loopback'
option ifname 'lo'
option proto 'static'
option ipaddr '127.0.0.1'
option netmask '255.0.0.0'

config globals 'globals'
option ula_prefix ''

config interface 'lan'
option type 'bridge'
option proto 'static'
option ipaddr '192.168.1.1'
option netmask '255.255.255.0'
option ip6assign '60'
option ifname 'eth0.1 tap0 tap-server'

config device 'lan_dev'
option name 'eth0.1'
option macaddr ''

config interface 'wan'
option ifname 'eth0.2'
option proto 'dhcp'
option metric '1'

config device 'wan_dev'
option name 'eth0.2'
option macaddr 'f8:5e:3c:04:06:ad'

config interface 'wan6'
option ifname 'eth0.2'
option proto 'dhcpv6'

config switch
option name 'switch0'
option reset '1'
option enable_vlan '1'

config switch_vlan
option device 'switch0'
option vlan '1'
option ports '0 1 2 3 6t'

config switch_vlan
option device 'switch0'
option vlan '2'
option ports '4 6t'

config interface 'VPN'
option proto 'none'
option ifname 'tun0'

config interface 'VPNS'
option proto 'none'
option ifname 'tun-server'

config interface 'TAP'
option proto 'none'
option ifname 'tap0'
option auto '1'

config interface 'TAPS'
option proto 'none'
option ifname 'tap-server'
option auto '1'

config interface 'Meekiemedia2'
option proto 'static'
option ipaddr '192.168.1.100'
option netmask '255.255.255.0'

config interface 'wwan'
option proto 'dhcp'
option metric '2'

config interface 'wan2'
option proto 'dhcp'
option metric '20'

config interface 'wan1'
option proto 'dhcp'
option ifname 'wwan0'
option _orig_bridge 'false'
option metric '10'

package dhcp

config dnsmasq
option domainneeded '1'
option boguspriv '1'
option filterwin2k '0'
option localise_queries '1'
option rebind_protection '0'
option rebind_localhost '1'
option local '/lan/'
option domain 'lan'
option expandhosts '1'
option nonegcache '0'
option authoritative '1'
option readethers '1'
option leasefile '/tmp/dhcp.leases'
option resolvfile '/tmp/resolv.conf.auto'
option nonwildcard '1'
option localservice '1'

config dhcp 'lan'
option interface 'lan'
option start '100'
option limit '150'
option leasetime '12h'
option dhcpv6 'server'
option ra 'server'

config dhcp 'wan'
option interface 'wan'
option ignore '1'

config odhcpd 'odhcpd'
option maindhcp '0'
option leasefile '/tmp/hosts/odhcpd'
option leasetrigger '/usr/sbin/odhcpd-update'
option loglevel '4'

config dhcp 'Meekiemedia2'
option interface 'Meekiemedia2'
option start '50'
option limit '200'
option leasetime '1h'

package firewall

config defaults
option syn_flood '1'
option input 'ACCEPT'
option output 'ACCEPT'
option forward 'REJECT'

config zone
option name 'lan'
list network 'lan'
option input 'ACCEPT'
option output 'ACCEPT'
option forward 'ACCEPT'

config zone
option name 'wan'
option input 'REJECT'
option output 'ACCEPT'
option forward 'REJECT'
option masq '1'
option mtu_fix '1'
option network 'wan wan6 wwan wan1 wan2'

config forwarding
option src 'lan'
option dest 'wan'

config rule
option name 'Allow-DHCP-Renew'
option src 'wan'
option proto 'udp'
option dest_port '68'
option target 'ACCEPT'
option family 'ipv4'

config rule
option name 'Allow-Ping'
option src 'wan'
option proto 'icmp'
option icmp_type 'echo-request'
option family 'ipv4'
option target 'ACCEPT'

config rule
option name 'Allow-IGMP'
option src 'wan'
option proto 'igmp'
option family 'ipv4'
option target 'ACCEPT'

config rule
option name 'Allow-DHCPv6'
option src 'wan'
option proto 'udp'
option src_ip 'fc00::/6'
option dest_ip 'fc00::/6'
option dest_port '546'
option family 'ipv6'
option target 'ACCEPT'

config rule
option name 'Allow-MLD'
option src 'wan'
option proto 'icmp'
option src_ip 'fe80::/10'
list icmp_type '130/0'
list icmp_type '131/0'
list icmp_type '132/0'
list icmp_type '143/0'
option family 'ipv6'
option target 'ACCEPT'

config rule
option name 'Allow-ICMPv6-Input'
option src 'wan'
option proto 'icmp'
list icmp_type 'echo-request'
list icmp_type 'echo-reply'
list icmp_type 'destination-unreachable'
list icmp_type 'packet-too-big'
list icmp_type 'time-exceeded'
list icmp_type 'bad-header'
list icmp_type 'unknown-header-type'
list icmp_type 'router-solicitation'
list icmp_type 'neighbour-solicitation'
list icmp_type 'router-advertisement'
list icmp_type 'neighbour-advertisement'
option limit '1000/sec'
option family 'ipv6'
option target 'ACCEPT'

config rule
option name 'Allow-ICMPv6-Forward'
option src 'wan'
option dest '*'
option proto 'icmp'
list icmp_type 'echo-request'
list icmp_type 'echo-reply'
list icmp_type 'destination-unreachable'
list icmp_type 'packet-too-big'
list icmp_type 'time-exceeded'
list icmp_type 'bad-header'
list icmp_type 'unknown-header-type'
option limit '1000/sec'
option family 'ipv6'
option target 'ACCEPT'

config rule
option name 'Allow-IPSec-ESP'
option src 'wan'
option dest 'lan'
option proto 'esp'
option target 'ACCEPT'

config rule
option name 'Allow-ISAKMP'
option src 'wan'
option dest 'lan'
option dest_port '500'
option proto 'udp'
option target 'ACCEPT'

config include
option path '/etc/firewall.user'

config zone 'vpnzone'
option name 'VPN'
option forward 'REJECT'
option output 'ACCEPT'
option network 'VPN'
option input 'REJECT'
option masq '1'
option mtu_fix '1'

config forwarding 'vpnforward'
option dest 'VPN'
option src 'lan'

config zone 'vpnzones'
option name 'VPNS'
option forward 'REJECT'
option output 'ACCEPT'
option network 'VPNS'
option input 'ACCEPT'
option masq '1'
option mtu_fix '1'

config forwarding 'vpnforwards'
option dest 'VPNS'
option src 'lan'

config zone 'Meekiemedia2_zone'
option name 'Meekiemedia2'
option network 'Meekiemedia2'
option input 'REJECT'
option forward 'REJECT'
option output 'ACCEPT'

config forwarding 'Meekiemedia2_forwarding'
option src 'Meekiemedia2'
option dest 'wan'

config rule 'Meekiemedia2_rule_dns'
option name 'Allow Meekiemedia2 DNS Queries'
option src 'Meekiemedia2'
option dest_port '53'
option proto 'tcpudp'
option target 'ACCEPT'

config rule 'Meekiemedia2_rule_dhcp'
option name 'Allow Meekiemedia2 DHCP request'
option src 'Meekiemedia2'
option src_port '68'
option dest_port '67'
option proto 'udp'
option target 'ACCEPT'

config zone '_zone'
option input 'REJECT'
option forward 'REJECT'
option output 'ACCEPT'

config forwarding '_forwarding'
option dest 'wan'

config rule '_rule_dns'
option name 'Allow DNS Queries'
option dest_port '53'
option proto 'tcpudp'
option target 'ACCEPT'

config rule '_rule_dhcp'
option name 'Allow DHCP request'
option src_port '68'
option dest_port '67'
option proto 'udp'
option target 'ACCEPT'

This file is interpreted as shell script.

Put your custom iptables rules here, they will

be executed with each firewall (re-)start.

Internal uci firewall chains are flushed and recreated on reload, so

put custom rules into the root chains e.g. INPUT or FORWARD or into the

special user chains, e.g. input_wan_rule or postrouting_lan_rule.

Generated by iptables-save v1.6.2 on Tue Mar 17 08:31:35 2020

*nat
:PREROUTING ACCEPT [16301:1340222]
:INPUT ACCEPT [14233:985059]
:OUTPUT ACCEPT [854:52591]
:POSTROUTING ACCEPT [854:52591]
:postrouting_Meekiemedia2_rule - [0:0]
:postrouting_VPNS_rule - [0:0]
:postrouting_VPN_rule - [0:0]
:postrouting_lan_rule - [0:0]
:postrouting_rule - [0:0]
:postrouting_wan_rule - [0:0]
:prerouting_Meekiemedia2_rule - [0:0]
:prerouting_VPNS_rule - [0:0]
:prerouting_VPN_rule - [0:0]
:prerouting_lan_rule - [0:0]
:prerouting_rule - [0:0]
:prerouting_wan_rule - [0:0]
:zone_Meekiemedia2_postrouting - [0:0]
:zone_Meekiemedia2_prerouting - [0:0]
:zone_VPNS_postrouting - [0:0]
:zone_VPNS_prerouting - [0:0]
:zone_VPN_postrouting - [0:0]
:zone_VPN_prerouting - [0:0]
:zone_lan_postrouting - [0:0]
:zone_lan_prerouting - [0:0]
:zone_wan_postrouting - [0:0]
:zone_wan_prerouting - [0:0]
[16301:1340222] -A PREROUTING -m comment --comment "!fw3: Custom prerouting rule chain" -j prerouting_rule
[16301:1340222] -A PREROUTING -i br-lan -m comment --comment "!fw3" -j zone_lan_prerouting
[0:0] -A PREROUTING -i eth0.2 -m comment --comment "!fw3" -j zone_wan_prerouting
[0:0] -A PREROUTING -i tun0 -m comment --comment "!fw3" -j zone_VPN_prerouting
[0:0] -A PREROUTING -i tun-server -m comment --comment "!fw3" -j zone_VPNS_prerouting
[0:0] -A PREROUTING -i wlan0-2 -m comment --comment "!fw3" -j zone_Meekiemedia2_prerouting
[854:52591] -A POSTROUTING -m comment --comment "!fw3: Custom postrouting rule chain" -j postrouting_rule
[32:5452] -A POSTROUTING -o br-lan -m comment --comment "!fw3" -j zone_lan_postrouting
[0:0] -A POSTROUTING -o eth0.2 -m comment --comment "!fw3" -j zone_wan_postrouting
[0:0] -A POSTROUTING -o tun0 -m comment --comment "!fw3" -j zone_VPN_postrouting
[0:0] -A POSTROUTING -o tun-server -m comment --comment "!fw3" -j zone_VPNS_postrouting
[0:0] -A POSTROUTING -o wlan0-2 -m comment --comment "!fw3" -j zone_Meekiemedia2_postrouting
[0:0] -A zone_Meekiemedia2_postrouting -m comment --comment "!fw3: Custom Meekiemedia2 postrouting rule chain" -j postrouting_Meekiemedia2_rule
[0:0] -A zone_Meekiemedia2_prerouting -m comment --comment "!fw3: Custom Meekiemedia2 prerouting rule chain" -j prerouting_Meekiemedia2_rule
[0:0] -A zone_VPNS_postrouting -m comment --comment "!fw3: Custom VPNS postrouting rule chain" -j postrouting_VPNS_rule
[0:0] -A zone_VPNS_postrouting -m comment --comment "!fw3" -j MASQUERADE
[0:0] -A zone_VPNS_prerouting -m comment --comment "!fw3: Custom VPNS prerouting rule chain" -j prerouting_VPNS_rule
[0:0] -A zone_VPN_postrouting -m comment --comment "!fw3: Custom VPN postrouting rule chain" -j postrouting_VPN_rule
[0:0] -A zone_VPN_postrouting -m comment --comment "!fw3" -j MASQUERADE
[0:0] -A zone_VPN_prerouting -m comment --comment "!fw3: Custom VPN prerouting rule chain" -j prerouting_VPN_rule
[32:5452] -A zone_lan_postrouting -m comment --comment "!fw3: Custom lan postrouting rule chain" -j postrouting_lan_rule
[16301:1340222] -A zone_lan_prerouting -m comment --comment "!fw3: Custom lan prerouting rule chain" -j prerouting_lan_rule
[0:0] -A zone_wan_postrouting -m comment --comment "!fw3: Custom wan postrouting rule chain" -j postrouting_wan_rule
[0:0] -A zone_wan_postrouting -m comment --comment "!fw3" -j MASQUERADE
[0:0] -A zone_wan_prerouting -m comment --comment "!fw3: Custom wan prerouting rule chain" -j prerouting_wan_rule
COMMIT

Completed on Tue Mar 17 08:31:35 2020

Generated by iptables-save v1.6.2 on Tue Mar 17 08:31:35 2020

*mangle
:PREROUTING ACCEPT [31873:2478986]
:INPUT ACCEPT [29805:2123823]
:FORWARD ACCEPT [0:0]
:OUTPUT ACCEPT [29297:4223079]
:POSTROUTING ACCEPT [29368:4232043]
[0:0] -A FORWARD -o eth0.2 -p tcp -m tcp --tcp-flags SYN,RST SYN -m comment --comment "!fw3: Zone wan MTU fixing" -j TCPMSS --clamp-mss-to-pmtu
[0:0] -A FORWARD -o tun0 -p tcp -m tcp --tcp-flags SYN,RST SYN -m comment --comment "!fw3: Zone VPN MTU fixing" -j TCPMSS --clamp-mss-to-pmtu
[0:0] -A FORWARD -o tun-server -p tcp -m tcp --tcp-flags SYN,RST SYN -m comment --comment "!fw3: Zone VPNS MTU fixing" -j TCPMSS --clamp-mss-to-pmtu
COMMIT

Completed on Tue Mar 17 08:31:35 2020

Generated by iptables-save v1.6.2 on Tue Mar 17 08:31:35 2020

*filter
:INPUT ACCEPT [0:0]
:FORWARD DROP [0:0]
:OUTPUT ACCEPT [0:0]
:RRDIPT - [0:0]
:forwarding_Meekiemedia2_rule - [0:0]
:forwarding_VPNS_rule - [0:0]
:forwarding_VPN_rule - [0:0]
:forwarding_lan_rule - [0:0]
:forwarding_rule - [0:0]
:forwarding_wan_rule - [0:0]
:input_Meekiemedia2_rule - [0:0]
:input_VPNS_rule - [0:0]
:input_VPN_rule - [0:0]
:input_lan_rule - [0:0]
:input_rule - [0:0]
:input_wan_rule - [0:0]
:output_Meekiemedia2_rule - [0:0]
:output_VPNS_rule - [0:0]
:output_VPN_rule - [0:0]
:output_lan_rule - [0:0]
:output_rule - [0:0]
:output_wan_rule - [0:0]
:reject - [0:0]
:syn_flood - [0:0]
:zone_Meekiemedia2_dest_ACCEPT - [0:0]
:zone_Meekiemedia2_dest_REJECT - [0:0]
:zone_Meekiemedia2_forward - [0:0]
:zone_Meekiemedia2_input - [0:0]
:zone_Meekiemedia2_output - [0:0]
:zone_Meekiemedia2_src_REJECT - [0:0]
:zone_VPNS_dest_ACCEPT - [0:0]
:zone_VPNS_dest_REJECT - [0:0]
:zone_VPNS_forward - [0:0]
:zone_VPNS_input - [0:0]
:zone_VPNS_output - [0:0]
:zone_VPNS_src_ACCEPT - [0:0]
:zone_VPN_dest_ACCEPT - [0:0]
:zone_VPN_dest_REJECT - [0:0]
:zone_VPN_forward - [0:0]
:zone_VPN_input - [0:0]
:zone_VPN_output - [0:0]
:zone_VPN_src_REJECT - [0:0]
:zone_lan_dest_ACCEPT - [0:0]
:zone_lan_forward - [0:0]
:zone_lan_input - [0:0]
:zone_lan_output - [0:0]
:zone_lan_src_ACCEPT - [0:0]
:zone_wan_dest_ACCEPT - [0:0]
:zone_wan_dest_REJECT - [0:0]
:zone_wan_forward - [0:0]
:zone_wan_input - [0:0]
:zone_wan_output - [0:0]
:zone_wan_src_REJECT - [0:0]
[4105:283632] -A INPUT -i lo -m comment --comment "!fw3" -j ACCEPT
[25702:1840271] -A INPUT -m comment --comment "!fw3: Custom input rule chain" -j input_rule
[11169:782360] -A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -m comment --comment "!fw3" -j ACCEPT
[57:2964] -A INPUT -p tcp -m tcp --tcp-flags FIN,SYN,RST,ACK SYN -m comment --comment "!fw3" -j syn_flood
[14533:1057911] -A INPUT -i br-lan -m comment --comment "!fw3" -j zone_lan_input
[0:0] -A INPUT -i eth0.2 -m comment --comment "!fw3" -j zone_wan_input
[0:0] -A INPUT -i tun0 -m comment --comment "!fw3" -j zone_VPN_input
[0:0] -A INPUT -i tun-server -m comment --comment "!fw3" -j zone_VPNS_input
[0:0] -A INPUT -i wlan0-2 -m comment --comment "!fw3" -j zone_Meekiemedia2_input
[0:0] -A FORWARD -j RRDIPT
[0:0] -A FORWARD -m comment --comment "!fw3: Custom forwarding rule chain" -j forwarding_rule
[0:0] -A FORWARD -m conntrack --ctstate RELATED,ESTABLISHED -m comment --comment "!fw3" -j ACCEPT
[0:0] -A FORWARD -m comment --comment "!fw3: Zone * to wan forwarding policy" -j zone_wan_dest_ACCEPT
[0:0] -A FORWARD -i br-lan -m comment --comment "!fw3" -j zone_lan_forward
[0:0] -A FORWARD -i eth0.2 -m comment --comment "!fw3" -j zone_wan_forward
[0:0] -A FORWARD -i tun0 -m comment --comment "!fw3" -j zone_VPN_forward
[0:0] -A FORWARD -i tun-server -m comment --comment "!fw3" -j zone_VPNS_forward
[0:0] -A FORWARD -i wlan0-2 -m comment --comment "!fw3" -j zone_Meekiemedia2_forward
[0:0] -A FORWARD -m comment --comment "!fw3" -j reject
[4105:283632] -A OUTPUT -o lo -m comment --comment "!fw3" -j ACCEPT
[25196:3940551] -A OUTPUT -m comment --comment "!fw3: Custom output rule chain" -j output_rule
[25118:3930708] -A OUTPUT -m conntrack --ctstate RELATED,ESTABLISHED -m comment --comment "!fw3" -j ACCEPT
[0:0] -A OUTPUT -p tcp -m tcp --dport 53 -m comment --comment "!fw3: Allow DNS Queries" -j ACCEPT
[0:0] -A OUTPUT -p udp -m udp --dport 53 -m comment --comment "!fw3: Allow DNS Queries" -j ACCEPT
[0:0] -A OUTPUT -p udp -m udp --sport 68 --dport 67 -m comment --comment "!fw3: Allow DHCP request" -j ACCEPT
[78:9843] -A OUTPUT -o br-lan -m comment --comment "!fw3" -j zone_lan_output
[0:0] -A OUTPUT -o eth0.2 -m comment --comment "!fw3" -j zone_wan_output
[0:0] -A OUTPUT -o tun0 -m comment --comment "!fw3" -j zone_VPN_output
[0:0] -A OUTPUT -o tun-server -m comment --comment "!fw3" -j zone_VPNS_output
[0:0] -A OUTPUT -o wlan0-2 -m comment --comment "!fw3" -j zone_Meekiemedia2_output
[0:0] -A RRDIPT -s 192.168.1.208/32 -j RETURN
[0:0] -A RRDIPT -d 192.168.1.208/32 -j RETURN
[0:0] -A RRDIPT -s 192.168.1.182/32 -j RETURN
[0:0] -A RRDIPT -d 192.168.1.182/32 -j RETURN
[0:0] -A RRDIPT -s 192.168.1.179/32 -j RETURN
[0:0] -A RRDIPT -d 192.168.1.179/32 -j RETURN
[0:0] -A reject -p tcp -m comment --comment "!fw3" -j REJECT --reject-with tcp-reset
[0:0] -A reject -m comment --comment "!fw3" -j REJECT --reject-with icmp-port-unreachable
[57:2964] -A syn_flood -p tcp -m tcp --tcp-flags FIN,SYN,RST,ACK SYN -m limit --limit 25/sec --limit-burst 50 -m comment --comment "!fw3" -j RETURN
[0:0] -A syn_flood -m comment --comment "!fw3" -j DROP
[0:0] -A zone_Meekiemedia2_dest_ACCEPT -o wlan0-2 -m comment --comment "!fw3" -j ACCEPT
[0:0] -A zone_Meekiemedia2_dest_REJECT -o wlan0-2 -m comment --comment "!fw3" -j reject
[0:0] -A zone_Meekiemedia2_forward -m comment --comment "!fw3: Custom Meekiemedia2 forwarding rule chain" -j forwarding_Meekiemedia2_rule
[0:0] -A zone_Meekiemedia2_forward -m comment --comment "!fw3: Zone Meekiemedia2 to wan forwarding policy" -j zone_wan_dest_ACCEPT
[0:0] -A zone_Meekiemedia2_forward -m conntrack --ctstate DNAT -m comment --comment "!fw3: Accept port forwards" -j ACCEPT
[0:0] -A zone_Meekiemedia2_forward -m comment --comment "!fw3" -j zone_Meekiemedia2_dest_REJECT
[0:0] -A zone_Meekiemedia2_input -m comment --comment "!fw3: Custom Meekiemedia2 input rule chain" -j input_Meekiemedia2_rule
[0:0] -A zone_Meekiemedia2_input -p tcp -m tcp --dport 53 -m comment --comment "!fw3: Allow Meekiemedia2 DNS Queries" -j ACCEPT
[0:0] -A zone_Meekiemedia2_input -p udp -m udp --dport 53 -m comment --comment "!fw3: Allow Meekiemedia2 DNS Queries" -j ACCEPT
[0:0] -A zone_Meekiemedia2_input -p udp -m udp --sport 68 --dport 67 -m comment --comment "!fw3: Allow Meekiemedia2 DHCP request" -j ACCEPT
[0:0] -A zone_Meekiemedia2_input -m conntrack --ctstate DNAT -m comment --comment "!fw3: Accept port redirections" -j ACCEPT
[0:0] -A zone_Meekiemedia2_input -m comment --comment "!fw3" -j zone_Meekiemedia2_src_REJECT
[0:0] -A zone_Meekiemedia2_output -m comment --comment "!fw3: Custom Meekiemedia2 output rule chain" -j output_Meekiemedia2_rule
[0:0] -A zone_Meekiemedia2_output -m comment --comment "!fw3" -j zone_Meekiemedia2_dest_ACCEPT
[0:0] -A zone_Meekiemedia2_src_REJECT -i wlan0-2 -m comment --comment "!fw3" -j reject
[0:0] -A zone_VPNS_dest_ACCEPT -o tun-server -m conntrack --ctstate INVALID -m comment --comment "!fw3: Prevent NAT leakage" -j DROP
[0:0] -A zone_VPNS_dest_ACCEPT -o tun-server -m comment --comment "!fw3" -j ACCEPT
[0:0] -A zone_VPNS_dest_REJECT -o tun-server -m comment --comment "!fw3" -j reject
[0:0] -A zone_VPNS_forward -m comment --comment "!fw3: Custom VPNS forwarding rule chain" -j forwarding_VPNS_rule
[0:0] -A zone_VPNS_forward -m conntrack --ctstate DNAT -m comment --comment "!fw3: Accept port forwards" -j ACCEPT
[0:0] -A zone_VPNS_forward -m comment --comment "!fw3" -j zone_VPNS_dest_REJECT
[0:0] -A zone_VPNS_input -m comment --comment "!fw3: Custom VPNS input rule chain" -j input_VPNS_rule
[0:0] -A zone_VPNS_input -m conntrack --ctstate DNAT -m comment --comment "!fw3: Accept port redirections" -j ACCEPT
[0:0] -A zone_VPNS_input -m comment --comment "!fw3" -j zone_VPNS_src_ACCEPT
[0:0] -A zone_VPNS_output -m comment --comment "!fw3: Custom VPNS output rule chain" -j output_VPNS_rule
[0:0] -A zone_VPNS_output -m comment --comment "!fw3" -j zone_VPNS_dest_ACCEPT
[0:0] -A zone_VPNS_src_ACCEPT -i tun-server -m conntrack --ctstate NEW,UNTRACKED -m comment --comment "!fw3" -j ACCEPT
[0:0] -A zone_VPN_dest_ACCEPT -o tun0 -m conntrack --ctstate INVALID -m comment --comment "!fw3: Prevent NAT leakage" -j DROP
[0:0] -A zone_VPN_dest_ACCEPT -o tun0 -m comment --comment "!fw3" -j ACCEPT
[0:0] -A zone_VPN_dest_REJECT -o tun0 -m comment --comment "!fw3" -j reject
[0:0] -A zone_VPN_forward -m comment --comment "!fw3: Custom VPN forwarding rule chain" -j forwarding_VPN_rule
[0:0] -A zone_VPN_forward -m conntrack --ctstate DNAT -m comment --comment "!fw3: Accept port forwards" -j ACCEPT
[0:0] -A zone_VPN_forward -m comment --comment "!fw3" -j zone_VPN_dest_REJECT
[0:0] -A zone_VPN_input -m comment --comment "!fw3: Custom VPN input rule chain" -j input_VPN_rule
[0:0] -A zone_VPN_input -m conntrack --ctstate DNAT -m comment --comment "!fw3: Accept port redirections" -j ACCEPT
[0:0] -A zone_VPN_input -m comment --comment "!fw3" -j zone_VPN_src_REJECT
[0:0] -A zone_VPN_output -m comment --comment "!fw3: Custom VPN output rule chain" -j output_VPN_rule
[0:0] -A zone_VPN_output -m comment --comment "!fw3" -j zone_VPN_dest_ACCEPT
[0:0] -A zone_VPN_src_REJECT -i tun0 -m comment --comment "!fw3" -j reject
[78:9843] -A zone_lan_dest_ACCEPT -o br-lan -m comment --comment "!fw3" -j ACCEPT
[0:0] -A zone_lan_forward -m comment --comment "!fw3: Custom lan forwarding rule chain" -j forwarding_lan_rule
[0:0] -A zone_lan_forward -m comment --comment "!fw3: Zone lan to wan forwarding policy" -j zone_wan_dest_ACCEPT
[0:0] -A zone_lan_forward -m comment --comment "!fw3: Zone lan to VPN forwarding policy" -j zone_VPN_dest_ACCEPT
[0:0] -A zone_lan_forward -m comment --comment "!fw3: Zone lan to VPNS forwarding policy" -j zone_VPNS_dest_ACCEPT
[0:0] -A zone_lan_forward -m conntrack --ctstate DNAT -m comment --comment "!fw3: Accept port forwards" -j ACCEPT
[0:0] -A zone_lan_forward -m comment --comment "!fw3" -j zone_lan_dest_ACCEPT
[14533:1057911] -A zone_lan_input -m comment --comment "!fw3: Custom lan input rule chain" -j input_lan_rule
[0:0] -A zone_lan_input -m conntrack --ctstate DNAT -m comment --comment "!fw3: Accept port redirections" -j ACCEPT
[14533:1057911] -A zone_lan_input -m comment --comment "!fw3" -j zone_lan_src_ACCEPT
[78:9843] -A zone_lan_output -m comment --comment "!fw3: Custom lan output rule chain" -j output_lan_rule
[78:9843] -A zone_lan_output -m comment --comment "!fw3" -j zone_lan_dest_ACCEPT
[14529:1057751] -A zone_lan_src_ACCEPT -i br-lan -m conntrack --ctstate NEW,UNTRACKED -m comment --comment "!fw3" -j ACCEPT
[0:0] -A zone_wan_dest_ACCEPT -o eth0.2 -m conntrack --ctstate INVALID -m comment --comment "!fw3: Prevent NAT leakage" -j DROP
[0:0] -A zone_wan_dest_ACCEPT -o eth0.2 -m comment --comment "!fw3" -j ACCEPT
[0:0] -A zone_wan_dest_REJECT -o eth0.2 -m comment --comment "!fw3" -j reject
[0:0] -A zone_wan_forward -m comment --comment "!fw3: Custom wan forwarding rule chain" -j forwarding_wan_rule
[0:0] -A zone_wan_forward -p esp -m comment --comment "!fw3: Allow-IPSec-ESP" -j zone_lan_dest_ACCEPT
[0:0] -A zone_wan_forward -p udp -m udp --dport 500 -m comment --comment "!fw3: Allow-ISAKMP" -j zone_lan_dest_ACCEPT
[0:0] -A zone_wan_forward -m conntrack --ctstate DNAT -m comment --comment "!fw3: Accept port forwards" -j ACCEPT
[0:0] -A zone_wan_forward -m comment --comment "!fw3" -j zone_wan_dest_REJECT
[0:0] -A zone_wan_input -m comment --comment "!fw3: Custom wan input rule chain" -j input_wan_rule
[0:0] -A zone_wan_input -p udp -m udp --dport 68 -m comment --comment "!fw3: Allow-DHCP-Renew" -j ACCEPT
[0:0] -A zone_wan_input -p icmp -m icmp --icmp-type 8 -m comment --comment "!fw3: Allow-Ping" -j ACCEPT
[0:0] -A zone_wan_input -p igmp -m comment --comment "!fw3: Allow-IGMP" -j ACCEPT
[0:0] -A zone_wan_input -m conntrack --ctstate DNAT -m comment --comment "!fw3: Accept port redirections" -j ACCEPT
[0:0] -A zone_wan_input -m comment --comment "!fw3" -j zone_wan_src_REJECT
[0:0] -A zone_wan_output -m comment --comment "!fw3: Custom wan output rule chain" -j output_wan_rule
[0:0] -A zone_wan_output -m comment --comment "!fw3" -j zone_wan_dest_ACCEPT
[0:0] -A zone_wan_src_REJECT -i eth0.2 -m comment --comment "!fw3" -j reject
COMMIT

Completed on Tue Mar 17 08:31:35 2020

Generated by ip6tables-save v1.6.2 on Tue Mar 17 08:31:35 2020

*mangle
:PREROUTING ACCEPT [41394:4026141]
:INPUT ACCEPT [40537:3804825]
:FORWARD ACCEPT [0:0]
:OUTPUT ACCEPT [39497:3708220]
:POSTROUTING ACCEPT [39497:3708220]
[0:0] -A FORWARD -o eth0.2 -p tcp -m tcp --tcp-flags SYN,RST SYN -m comment --comment "!fw3: Zone wan MTU fixing" -j TCPMSS --clamp-mss-to-pmtu
[0:0] -A FORWARD -o tun0 -p tcp -m tcp --tcp-flags SYN,RST SYN -m comment --comment "!fw3: Zone VPN MTU fixing" -j TCPMSS --clamp-mss-to-pmtu
[0:0] -A FORWARD -o tun-server -p tcp -m tcp --tcp-flags SYN,RST SYN -m comment --comment "!fw3: Zone VPNS MTU fixing" -j TCPMSS --clamp-mss-to-pmtu
COMMIT

Completed on Tue Mar 17 08:31:35 2020

Generated by ip6tables-save v1.6.2 on Tue Mar 17 08:31:35 2020

*filter
:INPUT ACCEPT [0:0]
:FORWARD DROP [0:0]
:OUTPUT ACCEPT [8:648]
:forwarding_Meekiemedia2_rule - [0:0]
:forwarding_VPNS_rule - [0:0]
:forwarding_VPN_rule - [0:0]
:forwarding_lan_rule - [0:0]
:forwarding_rule - [0:0]
:forwarding_wan_rule - [0:0]
:input_Meekiemedia2_rule - [0:0]
:input_VPNS_rule - [0:0]
:input_VPN_rule - [0:0]
:input_lan_rule - [0:0]
:input_rule - [0:0]
:input_wan_rule - [0:0]
:output_Meekiemedia2_rule - [0:0]
:output_VPNS_rule - [0:0]
:output_VPN_rule - [0:0]
:output_lan_rule - [0:0]
:output_rule - [0:0]
:output_wan_rule - [0:0]
:reject - [0:0]
:syn_flood - [0:0]
:zone_Meekiemedia2_dest_ACCEPT - [0:0]
:zone_Meekiemedia2_dest_REJECT - [0:0]
:zone_Meekiemedia2_forward - [0:0]
:zone_Meekiemedia2_input - [0:0]
:zone_Meekiemedia2_output - [0:0]
:zone_Meekiemedia2_src_REJECT - [0:0]
:zone_VPNS_dest_ACCEPT - [0:0]
:zone_VPNS_dest_REJECT - [0:0]
:zone_VPNS_forward - [0:0]
:zone_VPNS_input - [0:0]
:zone_VPNS_output - [0:0]
:zone_VPNS_src_ACCEPT - [0:0]
:zone_VPN_dest_ACCEPT - [0:0]
:zone_VPN_dest_REJECT - [0:0]
:zone_VPN_forward - [0:0]
:zone_VPN_input - [0:0]
:zone_VPN_output - [0:0]
:zone_VPN_src_REJECT - [0:0]
:zone_lan_dest_ACCEPT - [0:0]
:zone_lan_forward - [0:0]
:zone_lan_input - [0:0]
:zone_lan_output - [0:0]
:zone_lan_src_ACCEPT - [0:0]
:zone_wan_dest_ACCEPT - [0:0]
:zone_wan_dest_REJECT - [0:0]
:zone_wan_forward - [0:0]
:zone_wan_input - [0:0]
:zone_wan_output - [0:0]
:zone_wan_src_REJECT - [0:0]Preformatted text

[soonerdolfan]

Preformatted text[0:0] -A INPUT -i lo -m comment --comment "!fw3" -j ACCEPT
[40537:3804825] -A INPUT -m comment --comment "!fw3: Custom input rule chain" -j input_rule
[31622:2992572] -A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -m comment --comment "!fw3" -j ACCEPT
[0:0] -A INPUT -p tcp -m tcp --tcp-flags FIN,SYN,RST,ACK SYN -m comment --comment "!fw3" -j syn_flood
[8915:812253] -A INPUT -i br-lan -m comment --comment "!fw3" -j zone_lan_input
[0:0] -A INPUT -i eth0.2 -m comment --comment "!fw3" -j zone_wan_input
[0:0] -A INPUT -i tun0 -m comment --comment "!fw3" -j zone_VPN_input
[0:0] -A INPUT -i tun-server -m comment --comment "!fw3" -j zone_VPNS_input
[0:0] -A INPUT -i wlan0-2 -m comment --comment "!fw3" -j zone_Meekiemedia2_input
[0:0] -A FORWARD -m comment --comment "!fw3: Custom forwarding rule chain" -j forwarding_rule
[0:0] -A FORWARD -m conntrack --ctstate RELATED,ESTABLISHED -m comment --comment "!fw3" -j ACCEPT
[0:0] -A FORWARD -m comment --comment "!fw3: Zone * to wan forwarding policy" -j zone_wan_dest_ACCEPT
[0:0] -A FORWARD -i br-lan -m comment --comment "!fw3" -j zone_lan_forward
[0:0] -A FORWARD -i eth0.2 -m comment --comment "!fw3" -j zone_wan_forward
[0:0] -A FORWARD -i tun0 -m comment --comment "!fw3" -j zone_VPN_forward
[0:0] -A FORWARD -i tun-server -m comment --comment "!fw3" -j zone_VPNS_forward
[0:0] -A FORWARD -i wlan0-2 -m comment --comment "!fw3" -j zone_Meekiemedia2_forward
[0:0] -A FORWARD -m comment --comment "!fw3" -j reject
[0:0] -A OUTPUT -o lo -m comment --comment "!fw3" -j ACCEPT
[39497:3708220] -A OUTPUT -m comment --comment "!fw3: Custom output rule chain" -j output_rule
[39143:3680224] -A OUTPUT -m conntrack --ctstate RELATED,ESTABLISHED -m comment --comment "!fw3" -j ACCEPT
[0:0] -A OUTPUT -p tcp -m tcp --dport 53 -m comment --comment "!fw3: Allow DNS Queries" -j ACCEPT
[0:0] -A OUTPUT -p udp -m udp --dport 53 -m comment --comment "!fw3: Allow DNS Queries" -j ACCEPT
[0:0] -A OUTPUT -p udp -m udp --sport 68 --dport 67 -m comment --comment "!fw3: Allow DHCP request" -j ACCEPT
[314:22516] -A OUTPUT -o br-lan -m comment --comment "!fw3" -j zone_lan_output
[32:4832] -A OUTPUT -o eth0.2 -m comment --comment "!fw3" -j zone_wan_output
[0:0] -A OUTPUT -o tun0 -m comment --comment "!fw3" -j zone_VPN_output
[0:0] -A OUTPUT -o tun-server -m comment --comment "!fw3" -j zone_VPNS_output
[0:0] -A OUTPUT -o wlan0-2 -m comment --comment "!fw3" -j zone_Meekiemedia2_output
[0:0] -A reject -p tcp -m comment --comment "!fw3" -j REJECT --reject-with tcp-reset
[0:0] -A reject -m comment --comment "!fw3" -j REJECT --reject-with icmp6-port-unreachable
[0:0] -A syn_flood -p tcp -m tcp --tcp-flags FIN,SYN,RST,ACK SYN -m limit --limit 25/sec --limit-burst 50 -m comment --comment "!fw3" -j RETURN
[0:0] -A syn_flood -m comment --comment "!fw3" -j DROP
[0:0] -A zone_Meekiemedia2_dest_ACCEPT -o wlan0-2 -m comment --comment "!fw3" -j ACCEPT
[0:0] -A zone_Meekiemedia2_dest_REJECT -o wlan0-2 -m comment --comment "!fw3" -j reject
[0:0] -A zone_Meekiemedia2_forward -m comment --comment "!fw3: Custom Meekiemedia2 forwarding rule chain" -j forwarding_Meekiemedia2_rule
[0:0] -A zone_Meekiemedia2_forward -m comment --comment "!fw3: Zone Meekiemedia2 to wan forwarding policy" -j zone_wan_dest_ACCEPT
[0:0] -A zone_Meekiemedia2_forward -m comment --comment "!fw3" -j zone_Meekiemedia2_dest_REJECT
[0:0] -A zone_Meekiemedia2_input -m comment --comment "!fw3: Custom Meekiemedia2 input rule chain" -j input_Meekiemedia2_rule
[0:0] -A zone_Meekiemedia2_input -p tcp -m tcp --dport 53 -m comment --comment "!fw3: Allow Meekiemedia2 DNS Queries" -j ACCEPT
[0:0] -A zone_Meekiemedia2_input -p udp -m udp --dport 53 -m comment --comment "!fw3: Allow Meekiemedia2 DNS Queries" -j ACCEPT
[0:0] -A zone_Meekiemedia2_input -p udp -m udp --sport 68 --dport 67 -m comment --comment "!fw3: Allow Meekiemedia2 DHCP request" -j ACCEPT
[0:0] -A zone_Meekiemedia2_input -m comment --comment "!fw3" -j zone_Meekiemedia2_src_REJECT
[0:0] -A zone_Meekiemedia2_output -m comment --comment "!fw3: Custom Meekiemedia2 output rule chain" -j output_Meekiemedia2_rule
[0:0] -A zone_Meekiemedia2_output -m comment --comment "!fw3" -j zone_Meekiemedia2_dest_ACCEPT
[0:0] -A zone_Meekiemedia2_src_REJECT -i wlan0-2 -m comment --comment "!fw3" -j reject
[0:0] -A zone_VPNS_dest_ACCEPT -o tun-server -m conntrack --ctstate INVALID -m comment --comment "!fw3: Prevent NAT leakage" -j DROP
[0:0] -A zone_VPNS_dest_ACCEPT -o tun-server -m comment --comment "!fw3" -j ACCEPT
[0:0] -A zone_VPNS_dest_REJECT -o tun-server -m comment --comment "!fw3" -j reject
[0:0] -A zone_VPNS_forward -m comment --comment "!fw3: Custom VPNS forwarding rule chain" -j forwarding_VPNS_rule
[0:0] -A zone_VPNS_forward -m comment --comment "!fw3" -j zone_VPNS_dest_REJECT
[0:0] -A zone_VPNS_input -m comment --comment "!fw3: Custom VPNS input rule chain" -j input_VPNS_rule
[0:0] -A zone_VPNS_input -m comment --comment "!fw3" -j zone_VPNS_src_ACCEPT
[0:0] -A zone_VPNS_output -m comment --comment "!fw3: Custom VPNS output rule chain" -j output_VPNS_rule
[0:0] -A zone_VPNS_output -m comment --comment "!fw3" -j zone_VPNS_dest_ACCEPT
[0:0] -A zone_VPNS_src_ACCEPT -i tun-server -m conntrack --ctstate NEW,UNTRACKED -m comment --comment "!fw3" -j ACCEPT
[0:0] -A zone_VPN_dest_ACCEPT -o tun0 -m conntrack --ctstate INVALID -m comment --comment "!fw3: Prevent NAT leakage" -j DROP
[0:0] -A zone_VPN_dest_ACCEPT -o tun0 -m comment --comment "!fw3" -j ACCEPT
[0:0] -A zone_VPN_dest_REJECT -o tun0 -m comment --comment "!fw3" -j reject
[0:0] -A zone_VPN_forward -m comment --comment "!fw3: Custom VPN forwarding rule chain" -j forwarding_VPN_rule
[0:0] -A zone_VPN_forward -m comment --comment "!fw3" -j zone_VPN_dest_REJECT
[0:0] -A zone_VPN_input -m comment --comment "!fw3: Custom VPN input rule chain" -j input_VPN_rule
[0:0] -A zone_VPN_input -m comment --comment "!fw3" -j zone_VPN_src_REJECT
[0:0] -A zone_VPN_output -m comment --comment "!fw3: Custom VPN output rule chain" -j output_VPN_rule
[0:0] -A zone_VPN_output -m comment --comment "!fw3" -j zone_VPN_dest_ACCEPT
[0:0] -A zone_VPN_src_REJECT -i tun0 -m comment --comment "!fw3" -j reject
[314:22516] -A zone_lan_dest_ACCEPT -o br-lan -m comment --comment "!fw3" -j ACCEPT
[0:0] -A zone_lan_forward -m comment --comment "!fw3: Custom lan forwarding rule chain" -j forwarding_lan_rule
[0:0] -A zone_lan_forward -m comment --comment "!fw3: Zone lan to wan forwarding policy" -j zone_wan_dest_ACCEPT
[0:0] -A zone_lan_forward -m comment --comment "!fw3: Zone lan to VPN forwarding policy" -j zone_VPN_dest_ACCEPT
[0:0] -A zone_lan_forward -m comment --comment "!fw3: Zone lan to VPNS forwarding policy" -j zone_VPNS_dest_ACCEPT
[0:0] -A zone_lan_forward -m comment --comment "!fw3" -j zone_lan_dest_ACCEPT
[8915:812253] -A zone_lan_input -m comment --comment "!fw3: Custom lan input rule chain" -j input_lan_rule
[8915:812253] -A zone_lan_input -m comment --comment "!fw3" -j zone_lan_src_ACCEPT
[314:22516] -A zone_lan_output -m comment --comment "!fw3: Custom lan output rule chain" -j output_lan_rule
[314:22516] -A zone_lan_output -m comment --comment "!fw3" -j zone_lan_dest_ACCEPT
[8915:812253] -A zone_lan_src_ACCEPT -i br-lan -m conntrack --ctstate NEW,UNTRACKED -m comment --comment "!fw3" -j ACCEPT
[0:0] -A zone_wan_dest_ACCEPT -o eth0.2 -m conntrack --ctstate INVALID -m comment --comment "!fw3: Prevent NAT leakage" -j DROP
[32:4832] -A zone_wan_dest_ACCEPT -o eth0.2 -m comment --comment "!fw3" -j ACCEPT
[0:0] -A zone_wan_dest_REJECT -o eth0.2 -m comment --comment "!fw3" -j reject
[0:0] -A zone_wan_forward -m comment --comment "!fw3: Custom wan forwarding rule chain" -j forwarding_wan_rule
[0:0] -A zone_wan_forward -p ipv6-icmp -m icmp6 --icmpv6-type 128 -m limit --limit 1000/sec -m comment --comment "!fw3: Allow-ICMPv6-Forward" -j ACCEPT
[0:0] -A zone_wan_forward -p ipv6-icmp -m icmp6 --icmpv6-type 129 -m limit --limit 1000/sec -m comment --comment "!fw3: Allow-ICMPv6-Forward" -j ACCEPT
[0:0] -A zone_wan_forward -p ipv6-icmp -m icmp6 --icmpv6-type 1 -m limit --limit 1000/sec -m comment --comment "!fw3: Allow-ICMPv6-Forward" -j ACCEPT
[0:0] -A zone_wan_forward -p ipv6-icmp -m icmp6 --icmpv6-type 2 -m limit --limit 1000/sec -m comment --comment "!fw3: Allow-ICMPv6-Forward" -j ACCEPT
[0:0] -A zone_wan_forward -p ipv6-icmp -m icmp6 --icmpv6-type 3 -m limit --limit 1000/sec -m comment --comment "!fw3: Allow-ICMPv6-Forward" -j ACCEPT
[0:0] -A zone_wan_forward -p ipv6-icmp -m icmp6 --icmpv6-type 4/0 -m limit --limit 1000/sec -m comment --comment "!fw3: Allow-ICMPv6-Forward" -j ACCEPT
[0:0] -A zone_wan_forward -p ipv6-icmp -m icmp6 --icmpv6-type 4/1 -m limit --limit 1000/sec -m comment --comment "!fw3: Allow-ICMPv6-Forward" -j ACCEPT
[0:0] -A zone_wan_forward -p esp -m comment --comment "!fw3: Allow-IPSec-ESP" -j zone_lan_dest_ACCEPT
[0:0] -A zone_wan_forward -p udp -m udp --dport 500 -m comment --comment "!fw3: Allow-ISAKMP" -j zone_lan_dest_ACCEPT
[0:0] -A zone_wan_forward -m comment --comment "!fw3" -j zone_wan_dest_REJECT
[0:0] -A zone_wan_input -m comment --comment "!fw3: Custom wan input rule chain" -j input_wan_rule
[0:0] -A zone_wan_input -s fc00::/6 -d fc00::/6 -p udp -m udp --dport 546 -m comment --comment "!fw3: Allow-DHCPv6" -j ACCEPT
[0:0] -A zone_wan_input -s fe80::/10 -p ipv6-icmp -m icmp6 --icmpv6-type 130/0 -m comment --comment "!fw3: Allow-MLD" -j ACCEPT
[0:0] -A zone_wan_input -s fe80::/10 -p ipv6-icmp -m icmp6 --icmpv6-type 131/0 -m comment --comment "!fw3: Allow-MLD" -j ACCEPT
[0:0] -A zone_wan_input -s fe80::/10 -p ipv6-icmp -m icmp6 --icmpv6-type 132/0 -m comment --comment "!fw3: Allow-MLD" -j ACCEPT
[0:0] -A zone_wan_input -s fe80::/10 -p ipv6-icmp -m icmp6 --icmpv6-type 143/0 -m comment --comment "!fw3: Allow-MLD" -j ACCEPT
[0:0] -A zone_wan_input -p ipv6-icmp -m icmp6 --icmpv6-type 128 -m limit --limit 1000/sec -m comment --comment "!fw3: Allow-ICMPv6-Input" -j ACCEPT
[0:0] -A zone_wan_input -p ipv6-icmp -m icmp6 --icmpv6-type 129 -m limit --limit 1000/sec -m comment --comment "!fw3: Allow-ICMPv6-Input" -j ACCEPT
[0:0] -A zone_wan_input -p ipv6-icmp -m icmp6 --icmpv6-type 1 -m limit --limit 1000/sec -m comment --comment "!fw3: Allow-ICMPv6-Input" -j ACCEPT
[0:0] -A zone_wan_input -p ipv6-icmp -m icmp6 --icmpv6-type 2 -m limit --limit 1000/sec -m comment --comment "!fw3: Allow-ICMPv6-Input" -j ACCEPT
[0:0] -A zone_wan_input -p ipv6-icmp -m icmp6 --icmpv6-type 3 -m limit --limit 1000/sec -m comment --comment "!fw3: Allow-ICMPv6-Input" -j ACCEPT
[0:0] -A zone_wan_input -p ipv6-icmp -m icmp6 --icmpv6-type 4/0 -m limit --limit 1000/sec -m comment --comment "!fw3: Allow-ICMPv6-Input" -j ACCEPT
[0:0] -A zone_wan_input -p ipv6-icmp -m icmp6 --icmpv6-type 4/1 -m limit --limit 1000/sec -m comment --comment "!fw3: Allow-ICMPv6-Input" -j ACCEPT
[0:0] -A zone_wan_input -p ipv6-icmp -m icmp6 --icmpv6-type 133 -m limit --limit 1000/sec -m comment --comment "!fw3: Allow-ICMPv6-Input" -j ACCEPT
[0:0] -A zone_wan_input -p ipv6-icmp -m icmp6 --icmpv6-type 135 -m limit --limit 1000/sec -m comment --comment "!fw3: Allow-ICMPv6-Input" -j ACCEPT
[0:0] -A zone_wan_input -p ipv6-icmp -m icmp6 --icmpv6-type 134 -m limit --limit 1000/sec -m comment --comment "!fw3: Allow-ICMPv6-Input" -j ACCEPT
[0:0] -A zone_wan_input -p ipv6-icmp -m icmp6 --icmpv6-type 136 -m limit --limit 1000/sec -m comment --comment "!fw3: Allow-ICMPv6-Input" -j ACCEPT
[0:0] -A zone_wan_input -m comment --comment "!fw3" -j zone_wan_src_REJECT
[32:4832] -A zone_wan_output -m comment --comment "!fw3: Custom wan output rule chain" -j output_wan_rule
[32:4832] -A zone_wan_output -m comment --comment "!fw3" -j zone_wan_dest_ACCEPT
[0:0] -A zone_wan_src_REJECT -i eth0.2 -m comment --comment "!fw3" -j reject
COMMIT

Completed on Tue Mar 17 08:31:35 2020

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
11: br-lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
inet 192.168.1.1/24 brd 192.168.1.255 scope global br-lan
valid_lft forever preferred_lft forever
17: wlan0-2: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000
inet 192.168.1.100/24 brd 192.168.1.255 scope global wlan0-2
valid_lft forever preferred_lft forever
192.168.1.0/24 dev br-lan proto kernel scope link src 192.168.1.1
192.168.1.0/24 dev wlan0-2 proto kernel scope link src 192.168.1.100 linkdown
broadcast 127.0.0.0 dev lo table local proto kernel scope link src 127.0.0.1
local 127.0.0.0/8 dev lo table local proto kernel scope host src 127.0.0.1
local 127.0.0.1 dev lo table local proto kernel scope host src 127.0.0.1
broadcast 127.255.255.255 dev lo table local proto kernel scope link src 127.0.0.1
broadcast 192.168.1.0 dev br-lan table local proto kernel scope link src 192.168.1.1
broadcast 192.168.1.0 dev wlan0-2 table local proto kernel scope link src 192.168.1.100 linkdown
local 192.168.1.1 dev br-lan table local proto kernel scope host src 192.168.1.1
local 192.168.1.100 dev wlan0-2 table local proto kernel scope host src 192.168.1.100
broadcast 192.168.1.255 dev br-lan table local proto kernel scope link src 192.168.1.1
broadcast 192.168.1.255 dev wlan0-2 table local proto kernel scope link src 192.168.1.100 linkdown
0: from all lookup local
32766: from all lookup main
32767: from all lookup default
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 state UNKNOWN qlen 1000
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 state UNKNOWN qlen 1000
inet6 fe80::fa5e:3cff:fe04:6ac/64 scope link
valid_lft forever preferred_lft forever
11: br-lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 state UP qlen 1000
inet6 fd7d:3567:b927::1/60 scope global noprefixroute
valid_lft forever preferred_lft forever
inet6 fe80::fa5e:3cff:fe04:6ac/64 scope link
valid_lft forever preferred_lft forever
13: eth0.2@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 state UP qlen 1000
inet6 fe80::fa5e:3cff:fe04:6ad/64 scope link
valid_lft forever preferred_lft forever
fd7d:3567:b927::/64 dev br-lan proto static metric 1024 pref medium
unreachable fd7d:3567:b927::/48 dev lo proto static metric 2147483647 error -148 pref medium
fe80::/64 dev eth0 proto kernel metric 256 pref medium
fe80::/64 dev eth0.2 proto kernel metric 256 pref medium
fe80::/64 dev br-lan proto kernel metric 256 pref medium
local ::1 dev lo table local proto kernel metric 0 pref medium
anycast fd7d:3567:b927:: dev br-lan table local proto kernel metric 0 pref medium
local fd7d:3567:b927::1 dev br-lan table local proto kernel metric 0 pref medium
anycast fe80:: dev eth0.2 table local proto kernel metric 0 pref medium
anycast fe80:: dev eth0 table local proto kernel metric 0 pref medium
anycast fe80:: dev br-lan table local proto kernel metric 0 pref medium
local fe80::fa5e:3cff:fe04:6ac dev eth0 table local proto kernel metric 0 pref medium
local fe80::fa5e:3cff:fe04:6ac dev br-lan table local proto kernel metric 0 pref medium
local fe80::fa5e:3cff:fe04:6ad dev eth0.2 table local proto kernel metric 0 pref medium
ff00::/8 dev eth0 table local metric 256 pref medium
ff00::/8 dev br-lan table local metric 256 pref medium
ff00::/8 dev eth0.2 table local metric 256 pref medium
0: from all lookup local
32766: from all lookup main
4200000001: from all iif lo failed_policy
4200000011: from all iif br-lan failed_policy
4200000017: from all iif wlan0-2 failed_policy
lrwxrwxrwx 1 root root 16 Aug 16 2018 /etc/resolv.conf -> /tmp/resolv.conf
-rw-r--r-- 1 root root 32 Mar 17 07:29 /tmp/resolv.conf
-rw-r--r-- 1 root root 0 Mar 17 07:29 /tmp/resolv.conf.auto
==> /etc/resolv.conf <==
search lan
nameserver 127.0.0.1

==> /tmp/resolv.conf <==
search lan
nameserver 127.0.0.1

==> /tmp/resolv.conf.auto <==
root@mifi:~#Preformatted text

[mk24]

Please, code tags.

It appears you're running a third-party build from 2018.

[soonerdolfan]

My phone uses the same tower for the 4g lte. so the tower is sending atleast. The instructions I followed for the modem got me an "iemi" for an ipad to use with the modem.
I wasn't sure what I was looking at in all that and it took me a bit to realize you meant to use a command line. I spent the summer trying to setup and learn a linux system and failed miserably.

I hope I got out all you said. Wasn't sure what I was looking at.

[soonerdolfan]

Sure, it will be a sec. I got to look up how to do that.

[soonerdolfan]

config interface 'loopback'
        option ifname 'lo'
        option proto 'static'
        option ipaddr '127.0.0.1'
        option netmask '255.0.0.0'

config globals 'globals'
        option ula_prefix 'fd/48'

config interface 'lan'
        option type 'bridge'
        option proto 'static'
        option ipaddr '192.168.1.1'
        option netmask '255.255.255.0'
        option ip6assign '60'
        option ifname 'eth0.1 tap0 tap-server'

config device 'lan_dev'
        option name 'eth0.1'
        option macaddr 'f8:ac'

config interface 'wan'
        option ifname 'eth0.2'
        option proto 'dhcp'
        option metric '1'

config device 'wan_dev'
        option name 'eth0.2'
        option macaddr 'f8:ad'

config interface 'wan6'
        option ifname 'eth0.2'
        option proto 'dhcpv6'

config switch
        option name 'switch0'
        option reset '1'
        option enable_vlan '1'

config switch_vlan
        option device 'switch0'
        option vlan '1'
        option ports '0 1 2 3 6t'

config switch_vlan
        option device 'switch0'
        option vlan '2'
        option ports '4 6t'

config interface 'VPN'
        option proto 'none'
        option ifname 'tun0'

config interface 'VPNS'
        option proto 'none'
        option ifname 'tun-server'

config interface 'TAP'
        option proto 'none'
        option ifname 'tap0'
        option auto '1'

config interface 'TAPS'
        option proto 'none'
        option ifname 'tap-server'
        option auto '1'

config interface 'Meekiemedia2'
        option proto 'static'
        option ipaddr '192.168.1.100'
        option netmask '255.255.255.0'

config interface 'wwan'
        option proto 'dhcp'
        option metric '2'

config interface 'wan2'
        option proto 'dhcp'
        option metric '20'

config interface 'wan1'
        option proto 'dhcp'
        option ifname 'wwan0'
        option _orig_bridge 'false'
        option metric '10'

package dhcp

config dnsmasq
        option domainneeded '1'
        option boguspriv '1'
        option filterwin2k '0'
        option localise_queries '1'
        option rebind_protection '0'
        option rebind_localhost '1'
        option local '/lan/'
        option domain 'lan'
        option expandhosts '1'
        option nonegcache '0'
        option authoritative '1'
        option readethers '1'
        option leasefile '/tmp/dhcp.leases'
        option resolvfile '/tmp/resolv.conf.auto'
        option nonwildcard '1'
        option localservice '1'

config dhcp 'lan'
        option interface 'lan'
        option start '100'
        option limit '150'
        option leasetime '12h'
        option dhcpv6 'server'
        option ra 'server'

config dhcp 'wan'
        option interface 'wan'
        option ignore '1'

config odhcpd 'odhcpd'
        option maindhcp '0'
        option leasefile '/tmp/hosts/odhcpd'
        option leasetrigger '/usr/sbin/odhcpd-update'
        option loglevel '4'

config dhcp 'Meekiemedia2'
        option interface 'Meekiemedia2'
        option start '50'
        option limit '200'
        option leasetime '1h'

package firewall

config defaults
        option syn_flood '1'
        option input 'ACCEPT'
        option output 'ACCEPT'
        option forward 'REJECT'

config zone
        option name 'lan'
        list network 'lan'
        option input 'ACCEPT'
        option output 'ACCEPT'
        option forward 'ACCEPT'

config zone
        option name 'wan'
        option input 'REJECT'
        option output 'ACCEPT'
        option forward 'REJECT'
        option masq '1'
        option mtu_fix '1'
        option network 'wan wan6 wwan wan1 wan2'

config forwarding
        option src 'lan'
        option dest 'wan'

config rule
        option name 'Allow-DHCP-Renew'
        option src 'wan'
        option proto 'udp'
        option dest_port '68'
        option target 'ACCEPT'
        option family 'ipv4'

config rule
        option name 'Allow-Ping'
        option src 'wan'
        option proto 'icmp'
        option icmp_type 'echo-request'
        option family 'ipv4'
        option target 'ACCEPT'

config rule
        option name 'Allow-IGMP'
        option src 'wan'
        option proto 'igmp'
        option family 'ipv4'
        option target 'ACCEPT'

config rule
        option name 'Allow-DHCPv6'
        option src 'wan'
        option proto 'udp'
        option src_ip 'fc00::/6'
        option dest_ip 'fc00::/6'
        option dest_port '546'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-MLD'
        option src 'wan'
        option proto 'icmp'
        option src_ip 'fe80::/10'
        list icmp_type '130/0'
        list icmp_type '131/0'
        list icmp_type '132/0'
        list icmp_type '143/0'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-ICMPv6-Input'
        option src 'wan'
        option proto 'icmp'
        list icmp_type 'echo-request'
        list icmp_type 'echo-reply'
        list icmp_type 'destination-unreachable'
        list icmp_type 'packet-too-big'
        list icmp_type 'time-exceeded'
        list icmp_type 'bad-header'
        list icmp_type 'unknown-header-type'
        list icmp_type 'router-solicitation'
        list icmp_type 'neighbour-solicitation'
        list icmp_type 'router-advertisement'
        list icmp_type 'neighbour-advertisement'
        option limit '1000/sec'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-ICMPv6-Forward'
        option src 'wan'
        option dest '*'
        option proto 'icmp'
        list icmp_type 'echo-request'
        list icmp_type 'echo-reply'
        list icmp_type 'destination-unreachable'
        list icmp_type 'packet-too-big'
        list icmp_type 'time-exceeded'
        list icmp_type 'bad-header'
        list icmp_type 'unknown-header-type'
        option limit '1000/sec'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-IPSec-ESP'
        option src 'wan'
        option dest 'lan'
        option proto 'esp'
        option target 'ACCEPT'

config rule
        option name 'Allow-ISAKMP'
        option src 'wan'
        option dest 'lan'
        option dest_port '500'
        option proto 'udp'
        option target 'ACCEPT'

config include
        option path '/etc/firewall.user'

config zone 'vpnzone'
        option name 'VPN'
        option forward 'REJECT'
        option output 'ACCEPT'
        option network 'VPN'
        option input 'REJECT'
        option masq '1'
        option mtu_fix '1'

config forwarding 'vpnforward'
        option dest 'VPN'
        option src 'lan'

config zone 'vpnzones'
        option name 'VPNS'
        option forward 'REJECT'
        option output 'ACCEPT'
        option network 'VPNS'
        option input 'ACCEPT'
        option masq '1'
        option mtu_fix '1'

config forwarding 'vpnforwards'
        option dest 'VPNS'
        option src 'lan'

config zone 'Meekiemedia2_zone'
        option name 'Meekiemedia2'
        option network 'Meekiemedia2'
        option input 'REJECT'
        option forward 'REJECT'
        option output 'ACCEPT'

config forwarding 'Meekiemedia2_forwarding'
        option src 'Meekiemedia2'
        option dest 'wan'

config rule 'Meekiemedia2_rule_dns'
        option name 'Allow Meekiemedia2 DNS Queries'
        option src 'Meekiemedia2'
        option dest_port '53'
        option proto 'tcpudp'
        option target 'ACCEPT'

config rule 'Meekiemedia2_rule_dhcp'
        option name 'Allow Meekiemedia2 DHCP request'
        option src 'Meekiemedia2'
        option src_port '68'
        option dest_port '67'
        option proto 'udp'
        option target 'ACCEPT'

config zone '_zone'
        option input 'REJECT'
        option forward 'REJECT'
        option output 'ACCEPT'

config forwarding '_forwarding'
        option dest 'wan'

config rule '_rule_dns'
        option name 'Allow  DNS Queries'
        option dest_port '53'
        option proto 'tcpudp'
        option target 'ACCEPT'

config rule '_rule_dhcp'
        option name 'Allow  DHCP request'
        option src_port '68'
        option dest_port '67'
        option proto 'udp'
        option target 'ACCEPT'

[trendy]

Edit the previous posts and add the preformatted text tags.

3 times ` before the first line and 3 times ` after the last line

They are very hard to read and indentation is void.

[zwei123]

i wrote with him on freenode irc.
The problem is not the router.
AT&T are rejecting the connection.
Test the sim card and APN in the phone => no connection
Thank you all for your help

[trendy]

If the problem is solved, feel free to mark the topic accordingly .