X5000R: 2.4Ghz problem after 5Ghz Up

Hello;
After power up or wifi reload, device connect to 2.4Ghz, but after 5Ghz up, the device have problem to connect...

/etc/config/wireless

config wifi-device 'radio0'
        option type 'mac80211'
        option path '1e140000.pcie/pci0000:00/0000:00:01.0/0000:02:00.0'
        option cell_density '1'
        option noscan '1'
        option hwmode '11g'
        option channel '1'
        option htmode 'HT20'
        option country 'BR'
        option txpower '20'

config wifi-iface 'wifi_24_ghz'
        option device 'radio0'
        option network 'lan'
        option mode 'ap'
        option ssid 'Casa-2.4Ghz'
        option encryption 'psk2+tkip+aes'
        option key ''
        option ieee80211r '1'
        option mobility_domain 'abcd'
        option ft_over_ds '1'
        option ft_psk_generate_local '0'
        option macaddr '00:00:00:24:05:01'
        option pmk_r1_push '0'
        list r0kh "00:00:00:24:05:01,000000240501,"
        list r0kh "00:00:00:24:06:01,000000240601,"
        list r1kh "00:00:00:24:05:01,00:00:00:24:05:01,"
        list r1kh "00:00:00:24:06:01,00:00:00:24:06:01,"
        option nasid "000000240501"
        option r1_key_holder "000000240501"
        option rsn_preauth '1'
        option disabled 0
        option disassoc_low_ack '0'

config wifi-iface 'wifi_24_iot'
        option device 'radio0'
        option network 'lan'
        option mode 'ap'
        option ssid 'Casa-IoT'
        option encryption 'psk2+tkip+aes'
        option key ''
        option macaddr '00:00:00:24:05:02'
        option ieee80211r '0'
        option disassoc_low_ack '0'

config wifi-device 'radio1'
        option type 'mac80211'
        option channel '100'
        option hwmode '11a'
        option path '1e140000.pcie/pci0000:00/0000:00:01.0/0000:02:00.0+1'
        option htmode 'HE80'
        option cell_density '0'
        option country 'BR'
        option txpower '20'

config wifi-iface 'wifi_5_ghz'
        option device 'radio1'
        option network 'lan'
        option mode 'ap'
        option ssid 'Casa'
        option encryption 'psk2+tkip+aes'
        option key ''
        option ieee80211r '1'
        option mobility_domain 'abcd'
        option ft_over_ds '1'
        option ft_psk_generate_local '0'
        option macaddr '00:00:00:50:05:01'
        option pmk_r1_push '0'
        list r0kh "00:00:00:50:05:01,000000500501,"
        list r0kh "00:00:00:50:06:01,000000500601,"
        list r1kh "00:00:00:50:05:01,00:00:00:50:05:01,"
        list r1kh "00:00:00:50:06:01,00:00:00:50:06:01,"
        option nasid "000000500501"
        option r1_key_holder "000000500501"
        option rsn_preauth '1'
        option disassoc_low_ack '0'
kernel log

[    0.000000] Linux version 5.4.143 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16279-5cc0535800)) #0 SMP Tue Aug 31 22:20:08 2021
[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[    0.000000] MIPS: machine is TOTOLINK X5000R
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] VPE topology {2,2} total 4
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] On node 0 totalpages: 65536
[    0.000000]   Normal zone: 576 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 65536 pages, LIFO batch:15
[    0.000000] percpu: Embedded 14 pages/cpu s26768 r8192 d22384 u57344
[    0.000000] pcpu-alloc: s26768 r8192 d22384 u57344 alloc=14*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 64960
[    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Writing ErrCtl register=00012404
[    0.000000] Readback ErrCtl register=00012404
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 250792K/262144K available (6087K kernel code, 204K rwdata, 748K rodata, 1268K init, 238K bss, 11352K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] NR_IRQS: 256
[    0.000000] random: get_random_bytes called from 0x806e3a3c with crng_init=0
[    0.000000] CPU Clock: 880MHz
[    0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[    0.000008] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[    0.007815] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360)
[    0.042012] pid_max: default: 32768 minimum: 301
[    0.046785] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.054011] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.064470] rcu: Hierarchical SRCU implementation.
[    0.069922] smp: Bringing up secondary CPUs ...
[    0.076062] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.076072] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.076085] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.076186] CPU1 revision is: 0001992f (MIPS 1004Kc)
[    0.102690] Synchronize counters for CPU 1: done.
[    0.143715] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.143723] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.143731] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.143791] CPU2 revision is: 0001992f (MIPS 1004Kc)
[    0.167449] Synchronize counters for CPU 2: done.
[    0.198820] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.198828] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.198836] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.198898] CPU3 revision is: 0001992f (MIPS 1004Kc)
[    0.225308] Synchronize counters for CPU 3: done.
[    0.255189] smp: Brought up 1 node, 4 CPUs
[    0.263478] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.273171] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[    0.280184] pinctrl core: initialized pinctrl subsystem
[    0.287104] NET: Registered protocol family 16
[    0.299008] FPU Affinity set after 4688 emulations
[    0.315425] random: fast init done
[    0.315940] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[    0.330104] clocksource: Switched to clocksource GIC
[    0.336780] thermal_sys: Registered thermal governor 'step_wise'
[    0.337264] NET: Registered protocol family 2
[    0.347692] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.355798] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.364122] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.371721] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.378811] TCP: Hash tables configured (established 2048 bind 2048)
[    0.385233] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.391715] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.398903] NET: Registered protocol family 1
[    0.403246] PCI: CLS 0 bytes, default 32
[    0.498068] 4 CPUs re-calibrate udelay(lpj = 1163264)
[    0.504673] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[    0.523567] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.529356] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.540869] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.550183] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.556062] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.561888] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.568148] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.577663] printk: console [ttyS0] disabled
[    0.581951] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[    0.590939] printk: console [ttyS0] enabled
[    0.599193] printk: bootconsole [early0] disabled
[    0.611631] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[    0.617969] spi-nor spi0.0: en25qh128 (16384 Kbytes)
[    0.623034] 4 fixed-partitions partitions found on MTD device spi0.0
[    0.629369] Creating 4 MTD partitions on "spi0.0":
[    0.634163] 0x000000000000-0x000000030000 : "u-boot"
[    0.640572] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.647233] 0x000000040000-0x000000050000 : "factory"
[    0.653726] 0x000000050000-0x000001000000 : "firmware"
[    0.660293] 2 uimage-fw partitions found on MTD device firmware
[    0.666224] Creating 2 MTD partitions on "firmware":
[    0.671188] 0x000000000000-0x0000002447e1 : "kernel"
[    0.677568] 0x0000002447e1-0x000000fb0000 : "rootfs"
[    0.683818] mtd: device 5 (rootfs) set to be root filesystem
[    0.689582] 1 squashfs-split partitions found on MTD device rootfs
[    0.695782] 0x0000005b0000-0x000000fb0000 : "rootfs_data"
[    0.703748] libphy: Fixed MDIO Bus: probed
[    0.732512] libphy: mdio: probed
[    0.735954] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[    0.745589] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[    0.756011] mt7621-pci 1e140000.pcie: Parsing DT failed
[    0.764174] NET: Registered protocol family 10
[    0.770034] Segment Routing with IPv6
[    0.773863] NET: Registered protocol family 17
[    0.778418] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    0.791602] 8021q: 802.1Q VLAN Support v1.8
[    0.797715] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[    0.814169] libphy: dsa slave smi: probed
[    0.818604] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY]
[    0.828272] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY]
[    0.837979] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY]
[    0.847671] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY]
[    0.857490] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY]
[    0.867202] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[    0.878424] DSA: tree 0 setup
[    0.881730] rt2880-pinmux pinctrl: pcie is already enabled
[    0.887369] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[    0.894959] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[    1.002085] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[    1.007663] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[    1.112872] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[    1.119824] mt7621-pci 1e140000.pcie: PCIE0 enabled
[    1.124692] mt7621-pci 1e140000.pcie: PCIE1 enabled
[    1.129567] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[    1.139023] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[    1.145382] pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
[    1.152246] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[    1.159110] pci_bus 0000:00: root bus resource [bus 00-ff]
[    1.164626] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[    1.170656] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    1.176913] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[    1.183240] pci 0000:00:00.0: supports D1
[    1.187254] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    1.193385] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[    1.199419] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    1.205678] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[    1.211998] pci 0000:00:01.0: supports D1
[    1.216004] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[    1.223099] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.231100] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.239329] pci 0000:01:00.0: [14c3:7916] type 00 class 0x000280
[    1.245393] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[    1.252619] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
[    1.259848] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
[    1.267177] pci 0000:01:00.0: supports D1 D2
[    1.271442] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    1.278094] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[    1.293186] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    1.298421] pci 0000:00:00.0:   bridge window [io  0x0000-0x0fff]
[    1.304502] pci 0000:00:00.0:   bridge window [mem 0x00000000-0x000fffff]
[    1.311279] pci 0000:00:00.0:   bridge window [mem 0x00000000-0x000fffff pref]
[    1.318500] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    1.325314] pci 0000:02:00.0: [14c3:7915] type 00 class 0x000280
[    1.331378] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[    1.338603] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
[    1.345823] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
[    1.353151] pci 0000:02:00.0: supports D1 D2
[    1.357416] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    1.364053] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[    1.379190] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[    1.384419] pci 0000:00:01.0:   bridge window [io  0x0000-0x0fff]
[    1.390505] pci 0000:00:01.0:   bridge window [mem 0x00000000-0x000fffff]
[    1.397278] pci 0000:00:01.0:   bridge window [mem 0x00000000-0x000fffff pref]
[    1.404491] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[    1.411145] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    1.417744] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    1.424695] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[    1.431297] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[    1.438249] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[    1.445025] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref]
[    1.452244] pci 0000:00:01.0: BAR 8: assigned [mem 0x60300000-0x603fffff]
[    1.459023] pci 0000:00:01.0: BAR 9: assigned [mem 0x60400000-0x605fffff pref]
[    1.466235] pci 0000:00:00.0: BAR 1: assigned [mem 0x60600000-0x6060ffff]
[    1.473014] pci 0000:00:01.0: BAR 1: assigned [mem 0x60610000-0x6061ffff]
[    1.479796] pci 0000:00:00.0: BAR 7: assigned [io  0x1e160000-0x1e160fff]
[    1.486575] pci 0000:00:01.0: BAR 7: assigned [io  0x1e161000-0x1e161fff]
[    1.493359] pci 0000:01:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref]
[    1.501102] pci 0000:01:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref]
[    1.508843] pci 0000:01:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref]
[    1.516585] pci 0000:00:00.0: PCI bridge to [bus 01]
[    1.521544] pci 0000:00:00.0:   bridge window [io  0x1e160000-0x1e160fff]
[    1.528322] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    1.535099] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x602fffff pref]
[    1.542317] pci 0000:02:00.0: BAR 0: assigned [mem 0x60400000-0x604fffff 64bit pref]
[    1.550074] pci 0000:02:00.0: BAR 2: assigned [mem 0x60500000-0x60503fff 64bit pref]
[    1.557812] pci 0000:02:00.0: BAR 4: assigned [mem 0x60504000-0x60504fff 64bit pref]
[    1.565549] pci 0000:00:01.0: PCI bridge to [bus 02]
[    1.570511] pci 0000:00:01.0:   bridge window [io  0x1e161000-0x1e161fff]
[    1.577284] pci 0000:00:01.0:   bridge window [mem 0x60300000-0x603fffff]
[    1.584065] pci 0000:00:01.0:   bridge window [mem 0x60400000-0x605fffff pref]
[    1.592067] hctosys: unable to open rtc device (rtc0)
[    1.602365] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    1.613726] Freeing unused kernel memory: 1268K
[    1.618283] This architecture does not have kernel memory protection.
[    1.624706] Run /sbin/init as init process
[    1.630036] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off
[    2.071007] init: Console is alive
[    2.074663] init: - watchdog -
[    2.676218] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    2.765321] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    2.774431] init: - preinit -
[    3.439991] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[    3.448323] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[    3.456810] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    3.582277] random: jshn: uninitialized urandom read (4 bytes read)
[    3.646655] random: jshn: uninitialized urandom read (4 bytes read)
[    3.685307] random: jshn: uninitialized urandom read (4 bytes read)
[    3.904237] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[    3.911270] 8021q: adding VLAN 0 to HW filter on device lan1
[    6.982596] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[    6.990121] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready
[    8.136039] jffs2: notice: (586) jffs2_build_xattr_subsystem: complete building xattr subsystem, 37 of xdatum (34 unchecked, 3 orphan) and 74 of xref (15 dead, 0 orphan) found.
[    8.154009] mount_root: switching to jffs2 overlay
[    8.164720] overlayfs: upper fs does not support tmpfile.
[    8.176265] urandom-seed: Seeding with /etc/urandom.seed
[    8.263690] mt7530 mdio-bus:1f lan1: Link is Down
[    8.283170] procd: - early -
[    8.286210] procd: - watchdog -
[    8.874222] procd: - watchdog -
[    8.878493] procd: - ubus -
[    8.979018] procd: - init -
[    9.629817] kmodloader: loading kernel modules from /etc/modules.d/*
[    9.648017] Loading modules backported from Linux version v5.10.42-0-g65859eca4dff
[    9.655635] Backport generated by backports.git v5.10.42-1-0-gbee5c545
[    9.678996] xt_time: kernel timezone is -0000
[    9.728482] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=23
[    9.733924] pci 0000:00:00.0: enabling device (0004 -> 0007)
[    9.739591] mt7915e_hif 0000:01:00.0: enabling device (0000 -> 0002)
[    9.746524] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=24
[    9.751967] pci 0000:00:01.0: enabling device (0004 -> 0007)
[    9.757635] mt7915e 0000:02:00.0: enabling device (0000 -> 0002)
[    9.765746] urngd: v1.0.2 started.
[    9.889669] mt7915e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20201105222230a
[    9.889669] 
[    9.902589] random: crng init done
[    9.905996] random: 7 urandom warning(s) missed due to ratelimiting
[   10.219596] mt7915e 0000:02:00.0: WM Firmware Version: ____000000, Build Time: 20201105222304
[   10.257197] mt7915e 0000:02:00.0: WA Firmware Version: DEV_000000, Build Time: 20201105222323
[   10.399363] PPP generic driver version 2.4.2
[   10.405046] NET: Registered protocol family 24
[   10.420795] kmodloader: done loading kernel modules from /etc/modules.d/*
[   15.533549] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[   15.550511] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[   15.558733] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   15.562018] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[   15.574618] 8021q: adding VLAN 0 to HW filter on device lan1
[   15.583496] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   15.590918] br-lan: port 1(lan1) entered blocking state
[   15.596302] br-lan: port 1(lan1) entered disabled state
[   15.602643] device lan1 entered promiscuous mode
[   15.607327] device eth0 entered promiscuous mode
[   15.646232] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
[   15.653954] 8021q: adding VLAN 0 to HW filter on device lan2
[   15.669720] br-lan: port 2(lan2) entered blocking state
[   15.675003] br-lan: port 2(lan2) entered disabled state
[   15.681757] device lan2 entered promiscuous mode
[   15.707826] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode
[   15.716718] 8021q: adding VLAN 0 to HW filter on device lan3
[   15.728056] br-lan: port 3(lan3) entered blocking state
[   15.733346] br-lan: port 3(lan3) entered disabled state
[   15.747518] device lan3 entered promiscuous mode
[   15.767848] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode
[   15.775240] 8021q: adding VLAN 0 to HW filter on device lan4
[   15.785024] br-lan: port 4(lan4) entered blocking state
[   15.790412] br-lan: port 4(lan4) entered disabled state
[   15.798344] device lan4 entered promiscuous mode
[   15.816186] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode
[   15.824686] 8021q: adding VLAN 0 to HW filter on device wan
[   15.833928] br-lan: port 5(wan) entered blocking state
[   15.839212] br-lan: port 5(wan) entered disabled state
[   15.846945] device wan entered promiscuous mode
[   18.630983] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[   18.638614] br-lan: port 1(lan1) entered blocking state
[   18.643967] br-lan: port 1(lan1) entered forwarding state
[   18.654830] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   18.934149] mt7530 mdio-bus:1f wan: Link is Up - 1Gbps/Full - flow control rx/tx
[   19.019681] br-lan: port 5(wan) entered blocking state
[   19.024934] br-lan: port 5(wan) entered forwarding state
[   19.041252] br-lan: port 6(wlan1) entered blocking state
[   19.046662] br-lan: port 6(wlan1) entered disabled state
[   19.053201] device wlan1 entered promiscuous mode
[   19.058562] br-lan: port 6(wlan1) entered blocking state
[   19.063975] br-lan: port 6(wlan1) entered forwarding state
[   19.309172] br-lan: port 7(wlan0) entered blocking state
[   19.314579] br-lan: port 7(wlan0) entered disabled state
[   19.320669] device wlan0 entered promiscuous mode
[   19.325955] br-lan: port 7(wlan0) entered blocking state
[   19.331385] br-lan: port 7(wlan0) entered forwarding state
[   19.654574] br-lan: port 6(wlan1) entered disabled state
[   19.661840] br-lan: port 7(wlan0) entered disabled state
[   20.068317] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   20.075162] br-lan: port 7(wlan0) entered blocking state
[   20.080607] br-lan: port 7(wlan0) entered forwarding state
[   20.114009] br-lan: port 8(wlan0-1) entered blocking state
[   20.119731] br-lan: port 8(wlan0-1) entered disabled state
[   20.126015] device wlan0-1 entered promiscuous mode
[   20.134743] br-lan: port 8(wlan0-1) entered blocking state
[   20.140306] br-lan: port 8(wlan0-1) entered forwarding state
[   20.679769] br-lan: port 8(wlan0-1) entered disabled state
[   20.754358] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[   20.761549] br-lan: port 8(wlan0-1) entered blocking state
[   20.767173] br-lan: port 8(wlan0-1) entered forwarding state
[   81.867486] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   81.874265] br-lan: port 6(wlan1) entered blocking state
[   81.879593] br-lan: port 6(wlan1) entered forwarding state
[  241.945051] Rekeying PTK for STA 4e:e6:b2:71:bb:e0 but driver can't safely do that.
[  345.980754] Rekeying PTK for STA 4e:e6:b2:71:bb:e0 but driver can't safely do that.
[  360.145988] device wlan1 left promiscuous mode
[  360.158331] br-lan: port 6(wlan1) entered disabled state
[  360.321066] br-lan: port 8(wlan0-1) entered disabled state
[  360.327913] device wlan0-1 left promiscuous mode
[  360.332627] br-lan: port 8(wlan0-1) entered disabled state
[  360.566137] device wlan0 left promiscuous mode
[  360.570899] br-lan: port 7(wlan0) entered disabled state
[  361.374073] br-lan: port 6(wlan1) entered blocking state
[  361.379434] br-lan: port 6(wlan1) entered disabled state
[  361.385590] device wlan1 entered promiscuous mode
[  361.390879] br-lan: port 6(wlan1) entered blocking state
[  361.396370] br-lan: port 6(wlan1) entered forwarding state
[  361.775954] br-lan: port 7(wlan0) entered blocking state
[  361.781343] br-lan: port 7(wlan0) entered disabled state
[  361.787406] device wlan0 entered promiscuous mode
[  361.792589] br-lan: port 7(wlan0) entered blocking state
[  361.798009] br-lan: port 7(wlan0) entered forwarding state
[  362.276963] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  362.291308] br-lan: port 8(wlan0-1) entered blocking state
[  362.297036] br-lan: port 8(wlan0-1) entered disabled state
[  362.303259] device wlan0-1 entered promiscuous mode
[  362.309710] br-lan: port 8(wlan0-1) entered blocking state
[  362.315336] br-lan: port 8(wlan0-1) entered forwarding state
[  362.322957] br-lan: port 6(wlan1) entered disabled state
[  362.329886] br-lan: port 8(wlan0-1) entered disabled state
[  362.815010] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[  362.821996] br-lan: port 8(wlan0-1) entered blocking state
[  362.827527] br-lan: port 8(wlan0-1) entered forwarding state
[  423.472528] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[  423.479233] br-lan: port 6(wlan1) entered blocking state
[  423.484592] br-lan: port 6(wlan1) entered forwarding state

Part of syslog

Hello, I am also having certain problems with the WiFi on this device. I set up WPA3 and AX thanks to this thread I created.

My problem is the opposite. The 2.4GHz radio works fine, but the 5GHz is emitting, but no device can connect to it after password exchange.
Steps tried:

  • Downgraded to WPA2 and no security.
  • Downgraded to 'VHT40'.
  • After each modification, applied configuration and rebooted device.

EDIT: I propose backing up your /etc/conf/wireless somewhere and check if both frequencies work with the basic configuration in the linked thread. If the basic configuration works, its something with your configuration. If not, its a problem with the builds for this device.

1 Like