Hello;
After power up or wifi reload, device connect to 2.4Ghz, but after 5Ghz up, the device have problem to connect...
/etc/config/wireless
config wifi-device 'radio0'
option type 'mac80211'
option path '1e140000.pcie/pci0000:00/0000:00:01.0/0000:02:00.0'
option cell_density '1'
option noscan '1'
option hwmode '11g'
option channel '1'
option htmode 'HT20'
option country 'BR'
option txpower '20'
config wifi-iface 'wifi_24_ghz'
option device 'radio0'
option network 'lan'
option mode 'ap'
option ssid 'Casa-2.4Ghz'
option encryption 'psk2+tkip+aes'
option key ''
option ieee80211r '1'
option mobility_domain 'abcd'
option ft_over_ds '1'
option ft_psk_generate_local '0'
option macaddr '00:00:00:24:05:01'
option pmk_r1_push '0'
list r0kh "00:00:00:24:05:01,000000240501,"
list r0kh "00:00:00:24:06:01,000000240601,"
list r1kh "00:00:00:24:05:01,00:00:00:24:05:01,"
list r1kh "00:00:00:24:06:01,00:00:00:24:06:01,"
option nasid "000000240501"
option r1_key_holder "000000240501"
option rsn_preauth '1'
option disabled 0
option disassoc_low_ack '0'
config wifi-iface 'wifi_24_iot'
option device 'radio0'
option network 'lan'
option mode 'ap'
option ssid 'Casa-IoT'
option encryption 'psk2+tkip+aes'
option key ''
option macaddr '00:00:00:24:05:02'
option ieee80211r '0'
option disassoc_low_ack '0'
config wifi-device 'radio1'
option type 'mac80211'
option channel '100'
option hwmode '11a'
option path '1e140000.pcie/pci0000:00/0000:00:01.0/0000:02:00.0+1'
option htmode 'HE80'
option cell_density '0'
option country 'BR'
option txpower '20'
config wifi-iface 'wifi_5_ghz'
option device 'radio1'
option network 'lan'
option mode 'ap'
option ssid 'Casa'
option encryption 'psk2+tkip+aes'
option key ''
option ieee80211r '1'
option mobility_domain 'abcd'
option ft_over_ds '1'
option ft_psk_generate_local '0'
option macaddr '00:00:00:50:05:01'
option pmk_r1_push '0'
list r0kh "00:00:00:50:05:01,000000500501,"
list r0kh "00:00:00:50:06:01,000000500601,"
list r1kh "00:00:00:50:05:01,00:00:00:50:05:01,"
list r1kh "00:00:00:50:06:01,00:00:00:50:06:01,"
option nasid "000000500501"
option r1_key_holder "000000500501"
option rsn_preauth '1'
option disassoc_low_ack '0'
kernel log
[ 0.000000] Linux version 5.4.143 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16279-5cc0535800)) #0 SMP Tue Aug 31 22:20:08 2021
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is TOTOLINK X5000R
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] Normal zone: 576 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65536 pages, LIFO batch:15
[ 0.000000] percpu: Embedded 14 pages/cpu s26768 r8192 d22384 u57344
[ 0.000000] pcpu-alloc: s26768 r8192 d22384 u57344 alloc=14*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Writing ErrCtl register=00012404
[ 0.000000] Readback ErrCtl register=00012404
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 250792K/262144K available (6087K kernel code, 204K rwdata, 748K rodata, 1268K init, 238K bss, 11352K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] random: get_random_bytes called from 0x806e3a3c with crng_init=0
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.000008] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[ 0.007815] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360)
[ 0.042012] pid_max: default: 32768 minimum: 301
[ 0.046785] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.054011] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.064470] rcu: Hierarchical SRCU implementation.
[ 0.069922] smp: Bringing up secondary CPUs ...
[ 0.076062] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.076072] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.076085] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.076186] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.102690] Synchronize counters for CPU 1: done.
[ 0.143715] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.143723] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.143731] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.143791] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.167449] Synchronize counters for CPU 2: done.
[ 0.198820] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.198828] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.198836] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.198898] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.225308] Synchronize counters for CPU 3: done.
[ 0.255189] smp: Brought up 1 node, 4 CPUs
[ 0.263478] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.273171] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.280184] pinctrl core: initialized pinctrl subsystem
[ 0.287104] NET: Registered protocol family 16
[ 0.299008] FPU Affinity set after 4688 emulations
[ 0.315425] random: fast init done
[ 0.315940] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[ 0.330104] clocksource: Switched to clocksource GIC
[ 0.336780] thermal_sys: Registered thermal governor 'step_wise'
[ 0.337264] NET: Registered protocol family 2
[ 0.347692] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.355798] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.364122] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.371721] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.378811] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.385233] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.391715] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.398903] NET: Registered protocol family 1
[ 0.403246] PCI: CLS 0 bytes, default 32
[ 0.498068] 4 CPUs re-calibrate udelay(lpj = 1163264)
[ 0.504673] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.523567] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.529356] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.540869] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.550183] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.556062] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.561888] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.568148] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.577663] printk: console [ttyS0] disabled
[ 0.581951] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 0.590939] printk: console [ttyS0] enabled
[ 0.599193] printk: bootconsole [early0] disabled
[ 0.611631] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 0.617969] spi-nor spi0.0: en25qh128 (16384 Kbytes)
[ 0.623034] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.629369] Creating 4 MTD partitions on "spi0.0":
[ 0.634163] 0x000000000000-0x000000030000 : "u-boot"
[ 0.640572] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.647233] 0x000000040000-0x000000050000 : "factory"
[ 0.653726] 0x000000050000-0x000001000000 : "firmware"
[ 0.660293] 2 uimage-fw partitions found on MTD device firmware
[ 0.666224] Creating 2 MTD partitions on "firmware":
[ 0.671188] 0x000000000000-0x0000002447e1 : "kernel"
[ 0.677568] 0x0000002447e1-0x000000fb0000 : "rootfs"
[ 0.683818] mtd: device 5 (rootfs) set to be root filesystem
[ 0.689582] 1 squashfs-split partitions found on MTD device rootfs
[ 0.695782] 0x0000005b0000-0x000000fb0000 : "rootfs_data"
[ 0.703748] libphy: Fixed MDIO Bus: probed
[ 0.732512] libphy: mdio: probed
[ 0.735954] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 0.745589] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[ 0.756011] mt7621-pci 1e140000.pcie: Parsing DT failed
[ 0.764174] NET: Registered protocol family 10
[ 0.770034] Segment Routing with IPv6
[ 0.773863] NET: Registered protocol family 17
[ 0.778418] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 0.791602] 8021q: 802.1Q VLAN Support v1.8
[ 0.797715] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 0.814169] libphy: dsa slave smi: probed
[ 0.818604] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY]
[ 0.828272] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY]
[ 0.837979] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY]
[ 0.847671] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY]
[ 0.857490] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY]
[ 0.867202] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[ 0.878424] DSA: tree 0 setup
[ 0.881730] rt2880-pinmux pinctrl: pcie is already enabled
[ 0.887369] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[ 0.894959] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[ 1.002085] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[ 1.007663] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[ 1.112872] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 1.119824] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 1.124692] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 1.129567] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 1.139023] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 1.145382] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 1.152246] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.159110] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.164626] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 1.170656] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.176913] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.183240] pci 0000:00:00.0: supports D1
[ 1.187254] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.193385] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 1.199419] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.205678] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.211998] pci 0000:00:01.0: supports D1
[ 1.216004] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 1.223099] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.231100] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.239329] pci 0000:01:00.0: [14c3:7916] type 00 class 0x000280
[ 1.245393] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[ 1.252619] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
[ 1.259848] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
[ 1.267177] pci 0000:01:00.0: supports D1 D2
[ 1.271442] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.278094] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[ 1.293186] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.298421] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.304502] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.311279] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref]
[ 1.318500] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.325314] pci 0000:02:00.0: [14c3:7915] type 00 class 0x000280
[ 1.331378] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[ 1.338603] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
[ 1.345823] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
[ 1.353151] pci 0000:02:00.0: supports D1 D2
[ 1.357416] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.364053] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[ 1.379190] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 1.384419] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 1.390505] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.397278] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff pref]
[ 1.404491] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 1.411145] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 1.417744] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.424695] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 1.431297] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.438249] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.445025] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref]
[ 1.452244] pci 0000:00:01.0: BAR 8: assigned [mem 0x60300000-0x603fffff]
[ 1.459023] pci 0000:00:01.0: BAR 9: assigned [mem 0x60400000-0x605fffff pref]
[ 1.466235] pci 0000:00:00.0: BAR 1: assigned [mem 0x60600000-0x6060ffff]
[ 1.473014] pci 0000:00:01.0: BAR 1: assigned [mem 0x60610000-0x6061ffff]
[ 1.479796] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff]
[ 1.486575] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff]
[ 1.493359] pci 0000:01:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref]
[ 1.501102] pci 0000:01:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref]
[ 1.508843] pci 0000:01:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref]
[ 1.516585] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.521544] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff]
[ 1.528322] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.535099] pci 0000:00:00.0: bridge window [mem 0x60100000-0x602fffff pref]
[ 1.542317] pci 0000:02:00.0: BAR 0: assigned [mem 0x60400000-0x604fffff 64bit pref]
[ 1.550074] pci 0000:02:00.0: BAR 2: assigned [mem 0x60500000-0x60503fff 64bit pref]
[ 1.557812] pci 0000:02:00.0: BAR 4: assigned [mem 0x60504000-0x60504fff 64bit pref]
[ 1.565549] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 1.570511] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff]
[ 1.577284] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff]
[ 1.584065] pci 0000:00:01.0: bridge window [mem 0x60400000-0x605fffff pref]
[ 1.592067] hctosys: unable to open rtc device (rtc0)
[ 1.602365] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 1.613726] Freeing unused kernel memory: 1268K
[ 1.618283] This architecture does not have kernel memory protection.
[ 1.624706] Run /sbin/init as init process
[ 1.630036] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off
[ 2.071007] init: Console is alive
[ 2.074663] init: - watchdog -
[ 2.676218] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.765321] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 2.774431] init: - preinit -
[ 3.439991] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 3.448323] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 3.456810] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 3.582277] random: jshn: uninitialized urandom read (4 bytes read)
[ 3.646655] random: jshn: uninitialized urandom read (4 bytes read)
[ 3.685307] random: jshn: uninitialized urandom read (4 bytes read)
[ 3.904237] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 3.911270] 8021q: adding VLAN 0 to HW filter on device lan1
[ 6.982596] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 6.990121] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready
[ 8.136039] jffs2: notice: (586) jffs2_build_xattr_subsystem: complete building xattr subsystem, 37 of xdatum (34 unchecked, 3 orphan) and 74 of xref (15 dead, 0 orphan) found.
[ 8.154009] mount_root: switching to jffs2 overlay
[ 8.164720] overlayfs: upper fs does not support tmpfile.
[ 8.176265] urandom-seed: Seeding with /etc/urandom.seed
[ 8.263690] mt7530 mdio-bus:1f lan1: Link is Down
[ 8.283170] procd: - early -
[ 8.286210] procd: - watchdog -
[ 8.874222] procd: - watchdog -
[ 8.878493] procd: - ubus -
[ 8.979018] procd: - init -
[ 9.629817] kmodloader: loading kernel modules from /etc/modules.d/*
[ 9.648017] Loading modules backported from Linux version v5.10.42-0-g65859eca4dff
[ 9.655635] Backport generated by backports.git v5.10.42-1-0-gbee5c545
[ 9.678996] xt_time: kernel timezone is -0000
[ 9.728482] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=23
[ 9.733924] pci 0000:00:00.0: enabling device (0004 -> 0007)
[ 9.739591] mt7915e_hif 0000:01:00.0: enabling device (0000 -> 0002)
[ 9.746524] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=24
[ 9.751967] pci 0000:00:01.0: enabling device (0004 -> 0007)
[ 9.757635] mt7915e 0000:02:00.0: enabling device (0000 -> 0002)
[ 9.765746] urngd: v1.0.2 started.
[ 9.889669] mt7915e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20201105222230a
[ 9.889669]
[ 9.902589] random: crng init done
[ 9.905996] random: 7 urandom warning(s) missed due to ratelimiting
[ 10.219596] mt7915e 0000:02:00.0: WM Firmware Version: ____000000, Build Time: 20201105222304
[ 10.257197] mt7915e 0000:02:00.0: WA Firmware Version: DEV_000000, Build Time: 20201105222323
[ 10.399363] PPP generic driver version 2.4.2
[ 10.405046] NET: Registered protocol family 24
[ 10.420795] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 15.533549] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 15.550511] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 15.558733] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 15.562018] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 15.574618] 8021q: adding VLAN 0 to HW filter on device lan1
[ 15.583496] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 15.590918] br-lan: port 1(lan1) entered blocking state
[ 15.596302] br-lan: port 1(lan1) entered disabled state
[ 15.602643] device lan1 entered promiscuous mode
[ 15.607327] device eth0 entered promiscuous mode
[ 15.646232] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 15.653954] 8021q: adding VLAN 0 to HW filter on device lan2
[ 15.669720] br-lan: port 2(lan2) entered blocking state
[ 15.675003] br-lan: port 2(lan2) entered disabled state
[ 15.681757] device lan2 entered promiscuous mode
[ 15.707826] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 15.716718] 8021q: adding VLAN 0 to HW filter on device lan3
[ 15.728056] br-lan: port 3(lan3) entered blocking state
[ 15.733346] br-lan: port 3(lan3) entered disabled state
[ 15.747518] device lan3 entered promiscuous mode
[ 15.767848] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode
[ 15.775240] 8021q: adding VLAN 0 to HW filter on device lan4
[ 15.785024] br-lan: port 4(lan4) entered blocking state
[ 15.790412] br-lan: port 4(lan4) entered disabled state
[ 15.798344] device lan4 entered promiscuous mode
[ 15.816186] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode
[ 15.824686] 8021q: adding VLAN 0 to HW filter on device wan
[ 15.833928] br-lan: port 5(wan) entered blocking state
[ 15.839212] br-lan: port 5(wan) entered disabled state
[ 15.846945] device wan entered promiscuous mode
[ 18.630983] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 18.638614] br-lan: port 1(lan1) entered blocking state
[ 18.643967] br-lan: port 1(lan1) entered forwarding state
[ 18.654830] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 18.934149] mt7530 mdio-bus:1f wan: Link is Up - 1Gbps/Full - flow control rx/tx
[ 19.019681] br-lan: port 5(wan) entered blocking state
[ 19.024934] br-lan: port 5(wan) entered forwarding state
[ 19.041252] br-lan: port 6(wlan1) entered blocking state
[ 19.046662] br-lan: port 6(wlan1) entered disabled state
[ 19.053201] device wlan1 entered promiscuous mode
[ 19.058562] br-lan: port 6(wlan1) entered blocking state
[ 19.063975] br-lan: port 6(wlan1) entered forwarding state
[ 19.309172] br-lan: port 7(wlan0) entered blocking state
[ 19.314579] br-lan: port 7(wlan0) entered disabled state
[ 19.320669] device wlan0 entered promiscuous mode
[ 19.325955] br-lan: port 7(wlan0) entered blocking state
[ 19.331385] br-lan: port 7(wlan0) entered forwarding state
[ 19.654574] br-lan: port 6(wlan1) entered disabled state
[ 19.661840] br-lan: port 7(wlan0) entered disabled state
[ 20.068317] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 20.075162] br-lan: port 7(wlan0) entered blocking state
[ 20.080607] br-lan: port 7(wlan0) entered forwarding state
[ 20.114009] br-lan: port 8(wlan0-1) entered blocking state
[ 20.119731] br-lan: port 8(wlan0-1) entered disabled state
[ 20.126015] device wlan0-1 entered promiscuous mode
[ 20.134743] br-lan: port 8(wlan0-1) entered blocking state
[ 20.140306] br-lan: port 8(wlan0-1) entered forwarding state
[ 20.679769] br-lan: port 8(wlan0-1) entered disabled state
[ 20.754358] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[ 20.761549] br-lan: port 8(wlan0-1) entered blocking state
[ 20.767173] br-lan: port 8(wlan0-1) entered forwarding state
[ 81.867486] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 81.874265] br-lan: port 6(wlan1) entered blocking state
[ 81.879593] br-lan: port 6(wlan1) entered forwarding state
[ 241.945051] Rekeying PTK for STA 4e:e6:b2:71:bb:e0 but driver can't safely do that.
[ 345.980754] Rekeying PTK for STA 4e:e6:b2:71:bb:e0 but driver can't safely do that.
[ 360.145988] device wlan1 left promiscuous mode
[ 360.158331] br-lan: port 6(wlan1) entered disabled state
[ 360.321066] br-lan: port 8(wlan0-1) entered disabled state
[ 360.327913] device wlan0-1 left promiscuous mode
[ 360.332627] br-lan: port 8(wlan0-1) entered disabled state
[ 360.566137] device wlan0 left promiscuous mode
[ 360.570899] br-lan: port 7(wlan0) entered disabled state
[ 361.374073] br-lan: port 6(wlan1) entered blocking state
[ 361.379434] br-lan: port 6(wlan1) entered disabled state
[ 361.385590] device wlan1 entered promiscuous mode
[ 361.390879] br-lan: port 6(wlan1) entered blocking state
[ 361.396370] br-lan: port 6(wlan1) entered forwarding state
[ 361.775954] br-lan: port 7(wlan0) entered blocking state
[ 361.781343] br-lan: port 7(wlan0) entered disabled state
[ 361.787406] device wlan0 entered promiscuous mode
[ 361.792589] br-lan: port 7(wlan0) entered blocking state
[ 361.798009] br-lan: port 7(wlan0) entered forwarding state
[ 362.276963] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 362.291308] br-lan: port 8(wlan0-1) entered blocking state
[ 362.297036] br-lan: port 8(wlan0-1) entered disabled state
[ 362.303259] device wlan0-1 entered promiscuous mode
[ 362.309710] br-lan: port 8(wlan0-1) entered blocking state
[ 362.315336] br-lan: port 8(wlan0-1) entered forwarding state
[ 362.322957] br-lan: port 6(wlan1) entered disabled state
[ 362.329886] br-lan: port 8(wlan0-1) entered disabled state
[ 362.815010] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[ 362.821996] br-lan: port 8(wlan0-1) entered blocking state
[ 362.827527] br-lan: port 8(wlan0-1) entered forwarding state
[ 423.472528] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 423.479233] br-lan: port 6(wlan1) entered blocking state
[ 423.484592] br-lan: port 6(wlan1) entered forwarding state
Part of syslog