dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.10.161 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 11.2.0 r20028-43d71ad93e) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Tue Jan 3 00:24:21 2023
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Phicomm K3
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Hit pending asynchronous external abort (FSR=0x00001c06) during first unmask, this is most likely caused by a firmware/bootloader bug.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] HighMem [mem 0x0000000008000000-0x000000009fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] node 0: [mem 0x0000000088000000-0x000000009fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000009fffffff]
[ 0.000000] On node 0 totalpages: 131072
[ 0.000000] Normal zone: 288 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] HighMem zone: 98304 pages, LIFO batch:31
[ 0.000000] percpu: Embedded 14 pages/cpu s27596 r8192 d21556 u57344
[ 0.000000] pcpu-alloc: s27596 r8192 d21556 u57344 alloc=14*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130784
[ 0.000000] Kernel command line:
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 509296K/524288K available (6212K kernel code, 570K rwdata, 816K rodata, 1024K init, 295K bss, 14992K reserved, 0K cma-reserved, 393216K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] L2C: DT/platform modifies aux control register: 0x0a130000 -> 0x3a530000
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 cache controller enabled, 16 ways, 256 kB
[ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x7e530001
[ 0.000010] sched_clock: 64 bits at 700MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.000024] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0xa17102bcf3, max_idle_ns: 440795224838 ns
[ 0.000043] Switching to timer-based delay loop, resolution 1ns
[ 0.000220] Calibrating delay loop (skipped), value calculated using timer frequency.. 1400.00 BogoMIPS (lpj=7000000)
[ 0.000231] pid_max: default: 32768 minimum: 301
[ 0.000315] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.000324] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.000867] CPU: Testing write buffer coherency: ok
[ 0.000901] CPU0: Spectre v2: using BPIALL workaround
[ 0.001111] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.001586] Setting up static identity map for 0x100000 - 0x10003c
[ 0.001702] rcu: Hierarchical SRCU implementation.
[ 0.001828] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.001981] smp: Bringing up secondary CPUs ...
[ 0.002579] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.002586] CPU1: Spectre v2: using BPIALL workaround
[ 0.002679] smp: Brought up 1 node, 2 CPUs
[ 0.002688] SMP: Total of 2 processors activated (2800.00 BogoMIPS).
[ 0.002693] CPU: WARNING: CPU(s) started in wrong/inconsistent modes (primary CPU mode 0x13)
[ 0.002697] CPU: This may indicate a broken bootloader or firmware.
[ 0.004436] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.004457] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.004577] pinctrl core: initialized pinctrl subsystem
[ 0.005246] NET: Registered protocol family 16
[ 0.005915] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.006634] thermal_sys: Registered thermal governor 'step_wise'
[ 0.026617] clocksource: Switched to clocksource arm_global_timer
[ 0.027440] NET: Registered protocol family 2
[ 0.027599] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.028340] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.028407] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.028424] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.028440] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.028559] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.028608] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.028875] NET: Registered protocol family 1
[ 0.028914] PCI: CLS 0 bytes, default 64
[ 0.030738] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.032766] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.032781] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.033429] bounce: pool size: 64 pages
[ 0.033494] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.034676] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.035639] printk: console [ttyS0] disabled
[ 0.035693] 18000300.serial: ttyS0 at MMIO 0x18000300 (irq = 26, base_baud = 7812500) is a 16550
[ 0.552953] printk: console [ttyS0] enabled
[ 0.557519] 18000400.serial: ttyS1 at MMIO 0x18000400 (irq = 26, base_baud = 7812500) is a 16550
[ 0.567530] bcm2835-rng 18004000.rng: hwrng registered
[ 0.657250] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
[ 0.663625] nand: Samsung NAND 128MiB 3,3V 8-bit
[ 0.668273] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.675875] iproc_nand 18028000.nand-controller: detected 128MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-4
[ 0.686806] Scanning device for bad blocks
[ 0.991291] Bad eraseblock 515 at 0x000004060000
[ 1.241883] random: crng init done
[ 1.291387] Bad eraseblock 1023 at 0x000007fe0000
[ 1.296384] 4 fixed-partitions partitions found on MTD device brcmnand.0
[ 1.303416] Creating 4 MTD partitions on "brcmnand.0":
[ 1.308607] 0x000000000000-0x000000080000 : "boot"
[ 1.313904] 0x000000080000-0x000000180000 : "nvram"
[ 1.319303] 0x000000180000-0x000000400000 : "phicomm"
[ 1.324842] 0x000000400000-0x000008000000 : "firmware"
[ 1.331405] 2 trx partitions found on MTD device firmware
[ 1.336860] Creating 2 MTD partitions on "firmware":
[ 1.341844] 0x00000000001c-0x000000400000 : "linux"
[ 1.346748] mtd: partition "linux" doesn't start on an erase/write block boundary -- force read-only
[ 1.356436] 0x000000400000-0x000007c00000 : "ubi"
[ 1.363413] bcm_iproc 18029200.spi: using bspi-mspi mode
[ 1.370726] iproc-mdio 18003000.mdio: Broadcom iProc MDIO bus registered
[ 1.378916] b53-srab-switch 18007000.ethernet-switch: found switch: BCM53012, rev 0
[ 1.386794] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded
[ 1.392869] bcma-host-soc 18000000.axi: bus0: Found chip with id 53030, rev 0x00 and package 0x00
[ 1.401877] bcma-host-soc 18000000.axi: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2A, class 0x0)
[ 1.412476] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22
[ 1.412486] bcma-host-soc 18000000.axi: bus0: Core 1 found: Chipcommon B (manuf 0x4BF, id 0x50B, rev 0x05, class 0x0)
[ 1.423217] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22
[ 1.423224] bcma-host-soc 18000000.axi: bus0: Core 2 found: DMA (manuf 0x4BF, id 0x502, rev 0x04, class 0x0)
[ 1.433205] bcma-host-soc 18000000.axi: bus0: Core 3 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x07, class 0x0)
[ 1.443610] bcma-host-soc 18000000.axi: bus0: Core 4 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x07, class 0x0)
[ 1.454018] bcma-host-soc 18000000.axi: bus0: Core 5 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x07, class 0x0)
[ 1.464427] bcma-host-soc 18000000.axi: bus0: Core 6 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x07, class 0x0)
[ 1.474785] bcma-host-soc 18000000.axi: bus0: Core 7 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x07, class 0x0)
[ 1.485320] bcma-host-soc 18000000.axi: bus0: Core 8 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x07, class 0x0)
[ 1.495861] bcma-host-soc 18000000.axi: bus0: Core 9 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x07, class 0x0)
[ 1.506413] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22
[ 1.506421] bcma-host-soc 18000000.axi: bus0: Core 10 found: ARM Cortex A9 core (ihost) (manuf 0x4BF, id 0x510, rev 0x07, class 0x0)
[ 1.518445] bcma-host-soc 18000000.axi: bus0: Core 11 found: USB 2.0 (manuf 0x4BF, id 0x504, rev 0x07, class 0x0)
[ 1.528837] bcma-host-soc 18000000.axi: bus0: Core 12 found: USB 3.0 (manuf 0x4BF, id 0x505, rev 0x07, class 0x0)
[ 1.539226] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22
[ 1.539233] bcma-host-soc 18000000.axi: bus0: Core 13 found: SDIO3 (manuf 0x4BF, id 0x503, rev 0x01, class 0x0)
[ 1.549436] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22
[ 1.549443] bcma-host-soc 18000000.axi: bus0: Core 14 found: I2S (manuf 0x4BF, id 0x834, rev 0x03, class 0x0)
[ 1.559468] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22
[ 1.559475] bcma-host-soc 18000000.axi: bus0: Core 15 found: ARM Cortex A9 JTAG (manuf 0x4BF, id 0x506, rev 0x01, class 0x0)
[ 1.570822] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22
[ 1.570829] bcma-host-soc 18000000.axi: bus0: Core 16 found: Denali DDR2/DDR3 memory controller (manuf 0x4BF, id 0x507, rev 0x01, class 0x0)
[ 1.583557] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22
[ 1.583564] bcma-host-soc 18000000.axi: bus0: Core 17 found: ROM (manuf 0x4BF, id 0x508, rev 0x08, class 0x0)
[ 1.593619] bcma-host-soc 18000000.axi: bus0: Core 18 found: NAND flash controller (manuf 0x4BF, id 0x509, rev 0x01, class 0x0)
[ 1.605219] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22
[ 1.605226] bcma-host-soc 18000000.axi: bus0: Core 19 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0)
[ 1.616668] bcma-host-soc 18000000.axi: bus0: Flash type not supported
[ 1.659855] bcma-host-soc 18000000.axi: bus0: Using SPROM revision 8 provided by platform.
[ 1.660131] bgmac_bcma bcma0:3: Found PHY addr: 30 (NOREGS)
[ 1.665737] bgmac_bcma bcma0:3: Support for Roboswitch not implemented
[ 1.673183] b53-srab-switch b53-srab-switch: invalid resource
[ 1.679014] b53-srab-switch: probe of b53-srab-switch failed with error -22
[ 1.686712] bgmac_bcma bcma0:4: Found PHY addr: 0
[ 1.691441] bgmac_bcma bcma0:4: Support for Roboswitch not implemented
[ 1.698004] bgmac_bcma bcma0:4: Invalid MAC addr: 00:00:00:00:00:00
[ 1.704297] bgmac_bcma bcma0:4: Using random MAC: ee:f9:7c:52:b2:60
[ 1.711985] bgmac_bcma bcma0:5: Found PHY addr: 0
[ 1.716761] bgmac_bcma bcma0:5: Support for Roboswitch not implemented
[ 1.723314] bgmac_bcma bcma0:5: Invalid MAC addr: 00:00:00:00:00:00
[ 1.729620] bgmac_bcma bcma0:5: Using random MAC: ce:0c:13:93:68:9d
[ 1.737379] bgmac_bcma bcma0:6: Unsupported core_unit 3
[ 1.742692] bgmac_bcma: probe of bcma0:6 failed with error -524
[ 1.748797] pcie_iproc_bcma bcma0:7: host bridge /axi@18000000/pcie@12000 ranges:
[ 1.756318] pcie_iproc_bcma bcma0:7: No bus range found for /axi@18000000/pcie@12000, using [bus 00-ff]
[ 1.765934] OF: /axi@18000000/pcie@12000: Missing device_type
[ 1.771709] pcie_iproc_bcma bcma0:7: non-prefetchable memory resource required
[ 1.896518] pcie_iproc_bcma bcma0:7: link: UP
[ 1.900988] pcie_iproc_bcma bcma0:7: PCI host bridge to bus 0000:00
[ 1.907298] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.912798] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fffffff]
[ 1.919724] pci 0000:00:00.0: [14e4:d612] type 01 class 0x060400
[ 1.925751] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x4 may corrupt adjacent RW1C bits
[ 1.935476] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
[ 1.942235] PCI: bus0: Fast back to back transfers disabled
[ 1.947844] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.955988] pci 0000:01:00.0: [14e4:4365] type 00 class 0x028000
[ 1.962037] pci_bus 0000:01: 2-byte config write to 0000:01:00.0 offset 0x4 may corrupt adjacent RW1C bits
[ 1.971742] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit]
[ 1.978562] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x007fffff 64bit]
[ 1.985369] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x000fffff 64bit pref]
[ 1.992694] pci 0000:01:00.0: supports D1 D2
[ 1.997572] PCI: bus1: Fast back to back transfers disabled
[ 2.003168] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 2.009831] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x08bfffff]
[ 2.016652] pci 0000:00:00.0: BAR 9: assigned [mem 0x08c00000-0x08cfffff 64bit pref]
[ 2.024420] pci 0000:01:00.0: BAR 2: assigned [mem 0x08000000-0x087fffff 64bit]
[ 2.031765] pci 0000:01:00.0: BAR 4: assigned [mem 0x08c00000-0x08cfffff 64bit pref]
[ 2.039541] pci 0000:01:00.0: BAR 0: assigned [mem 0x08800000-0x08807fff 64bit]
[ 2.046877] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.051852] pci 0000:00:00.0: bridge window [mem 0x08000000-0x08bfffff]
[ 2.058664] pci 0000:00:00.0: bridge window [mem 0x08c00000-0x08cfffff 64bit pref]
[ 2.066648] pcie_iproc_bcma bcma0:8: host bridge /axi@18000000/pcie@13000 ranges:
[ 2.074168] pcie_iproc_bcma bcma0:8: No bus range found for /axi@18000000/pcie@13000, using [bus 00-ff]
[ 2.083791] pcie_iproc_bcma bcma0:8: non-prefetchable memory resource required
[ 2.206514] pcie_iproc_bcma bcma0:8: link: UP
[ 2.210982] pcie_iproc_bcma bcma0:8: PCI host bridge to bus 0001:00
[ 2.217298] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 2.222799] pci_bus 0001:00: root bus resource [mem 0x20000000-0x27ffffff]
[ 2.229726] pci 0001:00:00.0: [14e4:d612] type 01 class 0x060400
[ 2.235752] pci_bus 0001:00: 2-byte config write to 0001:00:00.0 offset 0x4 may corrupt adjacent RW1C bits
[ 2.245479] pci 0001:00:00.0: PME# supported from D0 D3hot D3cold
[ 2.252212] PCI: bus0: Fast back to back transfers disabled
[ 2.257821] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 2.265962] pci 0001:01:00.0: [14e4:4365] type 00 class 0x028000
[ 2.272011] pci_bus 0001:01: 2-byte config write to 0001:01:00.0 offset 0x4 may corrupt adjacent RW1C bits
[ 2.281714] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit]
[ 2.288536] pci 0001:01:00.0: reg 0x18: [mem 0x00000000-0x007fffff 64bit]
[ 2.295344] pci 0001:01:00.0: reg 0x20: [mem 0x00000000-0x000fffff 64bit pref]
[ 2.302669] pci 0001:01:00.0: supports D1 D2
[ 2.307561] PCI: bus1: Fast back to back transfers disabled
[ 2.313153] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01
[ 2.319817] pci 0001:00:00.0: BAR 8: assigned [mem 0x20000000-0x20bfffff]
[ 2.326636] pci 0001:00:00.0: BAR 9: assigned [mem 0x20c00000-0x20cfffff 64bit pref]
[ 2.334395] pci 0001:01:00.0: BAR 2: assigned [mem 0x20000000-0x207fffff 64bit]
[ 2.341739] pci 0001:01:00.0: BAR 4: assigned [mem 0x20c00000-0x20cfffff 64bit pref]
[ 2.349517] pci 0001:01:00.0: BAR 0: assigned [mem 0x20800000-0x20807fff 64bit]
[ 2.356853] pci 0001:00:00.0: PCI bridge to [bus 01]
[ 2.361828] pci 0001:00:00.0: bridge window [mem 0x20000000-0x20bfffff]
[ 2.368640] pci 0001:00:00.0: bridge window [mem 0x20c00000-0x20cfffff 64bit pref]
[ 2.376611] pcie_iproc_bcma bcma0:9: host bridge /axi@18000000/pcie@14000 ranges:
[ 2.384127] pcie_iproc_bcma bcma0:9: No bus range found for /axi@18000000/pcie@14000, using [bus 00-ff]
[ 2.393750] pcie_iproc_bcma bcma0:9: non-prefetchable memory resource required
[ 2.516514] pcie_iproc_bcma bcma0:9: PHY or data link is INACTIVE!
[ 2.522712] pcie_iproc_bcma bcma0:9: no PCIe EP device detected
[ 2.529454] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
[ 2.538528] bcma-host-soc 18000000.axi: bus0: Bus registered
[ 2.545048] NET: Registered protocol family 10
[ 2.550481] Segment Routing with IPv6
[ 2.554201] NET: Registered protocol family 17
[ 2.558744] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.571917] 8021q: 802.1Q VLAN Support v1.8
[ 2.576136] Registering SWP/SWPB emulation handler
[ 2.583643] b53-srab-switch 18007000.ethernet-switch: found switch: BCM53012, rev 0
[ 2.709500] b53-srab-switch 18007000.ethernet-switch lan1 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY] (irq=POLL)
[ 2.721961] b53-srab-switch 18007000.ethernet-switch lan2 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY] (irq=POLL)
[ 2.734367] b53-srab-switch 18007000.ethernet-switch lan3 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY] (irq=POLL)
[ 2.746805] b53-srab-switch 18007000.ethernet-switch wan (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY] (irq=POLL)
[ 2.758573] b53-srab-switch 18007000.ethernet-switch: Using legacy PHYLIB callbacks. Please migrate to PHYLINK!
[ 2.768967] DSA: tree 0 setup
[ 2.772641] UBI: auto-attach mtd5
[ 2.775976] ubi0: attaching mtd5
[ 3.393602] ubi0: scanning is finished
[ 3.405927] ubi0: attached mtd5 (name "ubi", size 120 MiB)
[ 3.411475] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.418379] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.425176] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.432155] ubi0: good PEBs: 958, bad PEBs: 2, corrupted PEBs: 0
[ 3.438177] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 3.445414] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1672705461
[ 3.454578] ubi0: available PEBs: 0, total reserved PEBs: 958, PEBs reserved for bad PEB handling: 18
[ 3.463871] ubi0: background thread "ubi_bgt0d" started, PID 456
[ 3.470726] block ubiblock0_0: created from ubi0:0(rootfs)
[ 3.476246] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 3.486739] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 3.494669] Freeing unused kernel memory: 1024K
[ 3.536626] Run /sbin/init as init process
[ 3.540729] with arguments:
[ 3.540731] /sbin/init
[ 3.540733] with environment:
[ 3.540736] HOME=/
[ 3.540738] TERM=linux
[ 3.738217] init: Console is alive
[ 3.741818] init: - watchdog -
[ 4.022259] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.086697] usbcore: registered new interface driver usbfs
[ 4.092285] usbcore: registered new interface driver hub
[ 4.097695] usbcore: registered new device driver usb
[ 4.105413] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.112750] ehci-fsl: Freescale EHCI Host controller driver
[ 4.119212] ehci-platform: EHCI generic platform driver
[ 4.126986] ehci-platform 18021000.usb: EHCI Host Controller
[ 4.129435] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.132697] ehci-platform 18021000.usb: new USB bus registered, assigned bus number 1
[ 4.140014] ohci-platform: OHCI generic platform driver
[ 4.147003] ehci-platform 18021000.usb: irq 45, io mem 0x18021000
[ 4.152329] ohci-platform 18022000.usb: Generic Platform OHCI controller
[ 4.165036] ohci-platform 18022000.usb: new USB bus registered, assigned bus number 2
[ 4.173030] ohci-platform 18022000.usb: irq 45, io mem 0x18022000
[ 4.186621] ehci-platform 18021000.usb: USB 2.0 started, EHCI 1.00
[ 4.193286] hub 1-0:1.0: USB hub found
[ 4.197133] hub 1-0:1.0: 2 ports detected
[ 4.251063] hub 2-0:1.0: USB hub found
[ 4.254874] hub 2-0:1.0: 2 ports detected
[ 4.285885] xhci-hcd 18023000.usb: xHCI Host Controller
[ 4.291179] xhci-hcd 18023000.usb: new USB bus registered, assigned bus number 3
[ 4.298816] xhci-hcd 18023000.usb: hcc params 0x02501164 hci version 0x100 quirks 0x0000200000010010
[ 4.308030] xhci-hcd 18023000.usb: irq 46, io mem 0x18023000
[ 4.315134] hub 3-0:1.0: USB hub found
[ 4.318971] hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 4.326267] xhci-hcd 18023000.usb: xHCI Host Controller
[ 4.331553] xhci-hcd 18023000.usb: new USB bus registered, assigned bus number 4
[ 4.339004] xhci-hcd 18023000.usb: Host supports USB 3.0 SuperSpeed
[ 4.346588] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.355104] hub 4-0:1.0: USB hub found
[ 4.358937] hub 4-0:1.0: 1 port detected
[ 4.364816] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.374424] init: - preinit -
[ 5.285713] b53-srab-switch 18007000.ethernet-switch lan1: configuring for phy/gmii link mode
[ 5.294371] bgmac_bcma bcma0:3 eth0: Link is Up - 1Gbps/Full - flow control off
[ 5.301883] 8021q: adding VLAN 0 to HW filter on device lan1
[ 5.366605] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 9.541532] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 9.547396] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 615
[ 9.603928] UBIFS (ubi0:1): recovery needed
[ 9.729769] UBIFS (ubi0:1): recovery completed
[ 9.734295] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 9.742151] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 9.752094] UBIFS (ubi0:1): FS size: 113008640 bytes (107 MiB, 890 LEBs), journal size 5713920 bytes (5 MiB, 45 LEBs)
[ 9.762731] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[ 9.769362] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 29D57AB9-245C-400C-93B4-6387A5AC29C3, small LPT model
[ 9.783482] mount_root: switching to ubifs overlay
[ 9.797072] urandom-seed: Seeding with /etc/urandom.seed
[ 9.970105] procd: - early -
[ 9.973107] procd: - watchdog -
[ 10.511423] procd: - watchdog -
[ 10.515970] procd: - ubus -
[ 10.574211] procd: - init -
[ 11.015480] urngd: v1.0.2 started.
[ 11.088243] kmodloader: loading kernel modules from /etc/modules.d/*
[ 11.150023] Loading modules backported from Linux version v5.15.81-0-ge4a7232c917c
[ 11.157639] Backport generated by backports.git v5.15.81-1-0-ge1867d55
[ 11.204259] PPP generic driver version 2.4.2
[ 11.210494] NET: Registered protocol family 24
[ 11.219298] usbcore: registered new interface driver brcmfmac
[ 11.225228] pci 0000:00:00.0: enabling device (0140 -> 0142)
[ 11.230948] brcmfmac 0000:01:00.0: enabling device (0140 -> 0142)
[ 11.356813] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4366c-pcie for chip BCM4366/4
[ 11.365585] brcmfmac 0000:01:00.0: Direct firmware load for brcm/brcmfmac4366c-pcie.phicomm,k3.bin failed with error -2
[ 11.587846] brcmfmac 0000:01:00.0: Direct firmware load for brcm/brcmfmac4366c-pcie.phicomm,k3.txt failed with error -2
[ 11.598738] brcmfmac 0000:01:00.0: Direct firmware load for brcm/brcmfmac4366c-pcie.txt failed with error -2
[ 11.959235] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4366c-pcie for chip BCM4366/4
[ 11.967978] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available
[ 11.979236] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4366/4 wl0: Nov 5 2018 03:19:56 version 10.28.2 (r769115) FWID 01-d2cbb8fd
[ 11.999388] pci 0001:00:00.0: enabling device (0140 -> 0142)
[ 12.005089] brcmfmac 0001:01:00.0: enabling device (0140 -> 0142)
[ 12.126911] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4366c-pcie for chip BCM4366/4
[ 12.135621] brcmfmac 0001:01:00.0: Direct firmware load for brcm/brcmfmac4366c-pcie.phicomm,k3.bin failed with error -2
[ 12.149824] brcmfmac 0001:01:00.0: Direct firmware load for brcm/brcmfmac4366c-pcie.phicomm,k3.txt failed with error -2
[ 12.160731] brcmfmac 0001:01:00.0: Direct firmware load for brcm/brcmfmac4366c-pcie.txt failed with error -2
[ 12.501677] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4366c-pcie for chip BCM4366/4
[ 12.510431] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available
[ 12.521761] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4366/4 wl0: Nov 5 2018 03:19:56 version 10.28.2 (r769115) FWID 01-d2cbb8fd
[ 12.552010] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 16.266315] bgmac_bcma bcma0:3 eth0: Link is Up - 1Gbps/Full - flow control off
[ 16.275290] b53-srab-switch 18007000.ethernet-switch lan1: configuring for phy/gmii link mode
[ 16.287495] 8021q: adding VLAN 0 to HW filter on device lan1
[ 16.346945] br-lan: port 1(lan1) entered blocking state
[ 16.352246] br-lan: port 1(lan1) entered disabled state
[ 16.357892] device lan1 entered promiscuous mode
[ 16.362547] device eth0 entered promiscuous mode
[ 16.458209] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 16.494317] b53-srab-switch 18007000.ethernet-switch lan2: configuring for phy/gmii link mode
[ 16.509821] 8021q: adding VLAN 0 to HW filter on device lan2
[ 16.575784] br-lan: port 2(lan2) entered blocking state
[ 16.581102] br-lan: port 2(lan2) entered disabled state
[ 16.586757] device lan2 entered promiscuous mode
[ 16.680269] b53-srab-switch 18007000.ethernet-switch lan3: configuring for phy/gmii link mode
[ 16.692261] 8021q: adding VLAN 0 to HW filter on device lan3
[ 16.786710] br-lan: port 3(lan3) entered blocking state
[ 16.792001] br-lan: port 3(lan3) entered disabled state
[ 16.797636] device lan3 entered promiscuous mode
[ 16.920108] b53-srab-switch 18007000.ethernet-switch wan: configuring for phy/gmii link mode
[ 16.930555] 8021q: adding VLAN 0 to HW filter on device wan
[ 19.523827] br-lan: port 4(wlan1) entered blocking state
[ 19.529209] br-lan: port 4(wlan1) entered disabled state
[ 19.534729] device wlan1 entered promiscuous mode
[ 31.904730] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 31.911253] br-lan: port 4(wlan1) entered blocking state
[ 31.916622] br-lan: port 4(wlan1) entered forwarding state
[ 31.923351] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready