Running the commands I had in first post to boot into the stock firmware outputs this, and then the subsequent reboot:
▒
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00158
S - IMAGE_VARIANT_STRING=HAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e1
B - 201 - PBL, Start
B - 2735 - bootable_media_detect_entry, Start
B - 2881 - bootable_media_detect_success, Start
B - 2885 - elf_loader_entry, Start
B - 11374 - auth_hash_seg_entry, Start
B - 11616 - auth_hash_seg_exit, Start
B - 250653 - elf_segs_hash_verify_entry, Start
B - 311323 - PBL, End
B - 320707 - SBL1, Start
B - 372252 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B - 378627 - pm_device_init, Start
B - 498949 - PM_SET_VAL:Skip
D - 119773 - pm_device_init, Delta
B - 501359 - pm_driver_init, Start
D - 5337 - pm_driver_init, Delta
B - 507672 - clock_init, Start
D - 2104 - clock_init, Delta
B - 511668 - boot_flash_init, Start
D - 15738 - boot_flash_init, Delta
B - 531188 - boot_config_data_table_init, Start
D - 1006 - boot_config_data_table_init, Delta - (575 Bytes)
B - 538843 - Boot Setting : 0x00000618
B - 542595 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:0
B - 549518 - sbl1_ddr_set_params, Start
B - 553331 - CPR configuration: 0x30c
B - 556777 - cpr_init, Start
B - 559553 - Rail:0 Mode: 5 Voltage: 800000
B - 564768 - CL CPR settled at 752000mV
B - 567605 - Rail:1 Mode: 5 Voltage: 880000
B - 571783 - Rail:1 Mode: 7 Voltage: 888000
D - 16531 - cpr_init, Delta
B - 578676 - Pre_DDR_clock_init, Start
B - 582672 - Pre_DDR_clock_init, End
B - 585966 - DDR Type : PCDDR3
B - 591669 - do ddr sanity test, Start
D - 1067 - do ddr sanity test, Delta
B - 596519 - DDR: Start of HAL DDR Boot Training
B - 601155 - DDR: End of HAL DDR Boot Training
B - 606950 - DDR: Checksum to be stored on flash is 410324843
B - 617167 - Image Load, Start
D - 335958 - QSEE Image Loaded, Delta - (1376448 Bytes)
B - 953216 - Image Load, Start
D - 61 - SEC Image Loaded, Delta - (0 Bytes)
B - 960872 - Image Load, Start
D - 9760 - DEVCFG Image Loaded, Delta - (26008 Bytes)
B - 970723 - Image Load, Start
D - 25956 - RPM Image Loaded, Delta - (86584 Bytes)
B - 996770 - Image Load, Start
D - 136579 - APPSBL Image Loaded, Delta - (556008 Bytes)
B - 1133471 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 1139266 - USB D+ check, Start
D - 0 - USB D+ check, Delta
B - 1145671 - SBL1, End
D - 827282 - SBL1, Delta
S - Flash Throughput, 4429 KB/s (2045623 Bytes, 461824 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 1651 MHz
U-Boot 2016.01 (Aug 18 2020 - 16:35:27 +0800)
DRAM: smem ram ptable found: ver: 1 len: 4
1 GiB
NAND: Could not find nand_gpio in dts, no defaults defined
Nand Flash error. Status = 80
Reset cmd status failed
SPI_ADDR_LEN=3
SF: Detected W25Q64DW with page size 256 Bytes, erase size 4 KiB, total 8 MiB
ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x800000
8 MiB
MMC: <NULL>: 0
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010000
Hit any key to stop autoboot: 0
Net: MAC0 addr:24:5e:be:53:3:93
PHY ID1: 0x0
PHY ID2: 0x0
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
eth0
IPQ807x#
IPQ807x#
IPQ807x#
IPQ807x#
IPQ807x# bootipq
MMC read: dev # 0, block # 32802, count 32768 ... 32768 blocks read: OK
## Loading kernel from FIT Image at 44000000 ...
Using 'config@hk01' configuration
Trying 'kernel@1' kernel subimage
Description: ARM64 OpenWrt Linux-4.4.60
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x440000e8
Data Size: 5085725 Bytes = 4.9 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x41080000
Entry Point: 0x41080000
Hash algo: crc32
Hash value: 5b7da156
Hash algo: sha1
Hash value: 5fe8caf0a9bd7d57f41f57b93ab53e1d412a9358
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
Using 'config@hk01' configuration
Trying 'fdt@hk01' fdt subimage
Description: ARM64 OpenWrt qcom-ipq807x-hk01 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x444d9c50
Data Size: 91766 Bytes = 89.6 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: 78edc81e
Hash algo: sha1
Hash value: fd8922842b5489fbfeaace1b659cca242cefe40d
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x444d9c50
Uncompressing Kernel Image ... OK
Loading Device Tree to 4a3e6000, end 4a3ff675 ... OK
Using machid 0x8010000 from environment
Starting kernel ...
Jumping to AARCH64 kernel via monitor
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.60 (root@qnap-build-machine) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 0784228+r49254) ) #6 SMP PREEMPT Mon May 9 15:13:51 CST 2022
[ 0.000000] Boot CPU: AArch64 Processor [410fd034]
[ 0.000000] Ignoring memory range 0x40000000 - 0x41000000
[ 0.000000] Machine: Qualcomm Technologies, Inc. IPQ807x/AP-HK01-C1
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: UEFI not found.
[ 0.000000] Reserved memory: OVERLAP DETECTED!
[ 0.000000] wifi_dump@51100000 (0x0000000051100000--0x0000000051700000) overlaps with wigig_dump@51300000 (0x0000000051300000--0x0000000051700000)
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] PERCPU: Embedded 15 pages/cpu @ffffffc03ef3f000 s21248 r8192 d32000 u61440
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 225036
[ 0.000000] Kernel command line: cpuidle.off=1 root=PARTUUID=2a213133-47f8-80a1-5d66-1d565a2ec756 rootwait swiotlb=1 coherent_pool=2M
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] software IO TLB [mem 0x7fd3a000-0x7fd7a000] (0MB) mapped at [ffffffc03ed3a000-ffffffc03ed79fff]
[ 0.000000] Memory: 882908K/914432K available (5704K kernel code, 646K rwdata, 2400K rodata, 2044K init, 489K bss, 31524K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000 ( 246 GB)
[ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum)
[ 0.000000] 0xffffffbdc0040000 - 0xffffffbdc1000000 ( 15 MB actual)
[ 0.000000] fixed : 0xffffffbffa7fd000 - 0xffffffbffac00000 ( 4108 KB)
[ 0.000000] PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000 ( 16 MB)
[ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc03f000000 ( 1008 MB)
[ 0.000000] .init : 0xffffffc00086c000 - 0xffffffc000a6b000 ( 2044 KB)
[ 0.000000] .text : 0xffffffc000080000 - 0xffffffc00086c000 ( 8112 KB)
[ 0.000000] .data : 0xffffffc000a7b000 - 0xffffffc000b1ca00 ( 647 KB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] Architected cp15 timer(s) running at 19.20MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000488] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.000500] pid_max: default: 32768 minimum: 301
[ 0.000600] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.000610] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.001167] Initializing cgroup subsys io
[ 0.001184] Initializing cgroup subsys memory
[ 0.001211] Initializing cgroup subsys devices
[ 0.001222] Initializing cgroup subsys freezer
[ 0.001232] Initializing cgroup subsys net_cls
[ 0.001242] Initializing cgroup subsys pids
[ 0.001484] EFI services will not be available.
[ 0.001508] ASID allocator initialised with 65536 entries
[ 0.052123] MSM Memory Dump base table set up
[ 0.052146] MSM Memory Dump apps data table set up
[ 0.090051] Detected VIPT I-cache on CPU1
[ 0.090097] CPU1: Booted secondary processor [410fd034]
[ 0.120038] Detected VIPT I-cache on CPU2
[ 0.120067] CPU2: Booted secondary processor [410fd034]
[ 0.150067] Detected VIPT I-cache on CPU3
[ 0.150095] CPU3: Booted secondary processor [410fd034]
[ 0.150148] Brought up 4 CPUs
[ 0.150175] SMP: Total of 4 processors activated.
[ 0.150186] CPU: All CPU(s) started at EL1
[ 0.150209] alternatives: patching kernel code
[ 0.150706] devtmpfs: initialized
[ 0.171307] DMI not present or invalid.
[ 0.171557] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.171578] futex hash table entries: 1024 (order: 5, 131072 bytes)
[ 0.171929] pinctrl core: initialized pinctrl subsystem
[ 0.172862] NET: Registered protocol family 16
[ 0.173638] NET: Registered protocol family 42
[ 0.173725] vdso: 2 pages (1 code @ ffffffc000a81000, 1 data @ ffffffc000a80000)
[ 0.173753] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.174397] DMA: preallocated 2048 KiB pool for atomic allocations
[ 0.174527] CPU: IPQ8072A, SoC Version: 2.0
[ 0.174964] IPC logging disabled
[ 0.174970] IPC logging disabled
[ 0.174975] IPC logging disabled
[ 0.174979] IPC logging disabled
[ 0.174984] IPC logging disabled
[ 0.177182] Soc version is not 1, changing clock offsets
[ 0.188798] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel !
[ 0.191638] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel !
[ 0.195103] sps:sps is ready.
[ 0.202017] spmi spmi-0: PMIC Arb Version-2 (0x20010000)
[ 0.208716] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 0.209013] qcom,cpr3-npu-regulator a4000.npu-cpr: NPU CPR valid fuse count: 2
[ 0.241906] pps_core: LinuxPPS API ver. 1 registered
[ 0.241914] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.241939] PTP clock support registered
[ 0.242096] dmi: Firmware registration failed.
[ 0.243547] Advanced Linux Sound Architecture Driver Initialized.
[ 0.244216] clocksource: Switched to clocksource arch_sys_counter
[ 0.247833] NET: Registered protocol family 2
[ 0.248576] default registered
[ 0.248584] default registered
[ 0.248590] MPTCP: Stable release v0.92.2
[ 0.248631] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.248738] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[ 0.248927] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.248983] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.249019] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.249210] NET: Registered protocol family 1
[ 0.259757] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[ 0.270810] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.270830] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.274659] Key type asymmetric registered
[ 0.274674] Asymmetric key parser 'x509' registered
[ 0.274702] io scheduler noop registered
[ 0.274713] io scheduler deadline registered (default)
[ 0.276372] hora_gpio: Register a char device 246:0
[ 0.277710] 20000000.pci supply vdda not found, using dummy regulator
[ 0.277756] 20000000.pci supply vdda_phy not found, using dummy regulator
[ 0.277814] 20000000.pci supply vdda_refclk not found, using dummy regulator
[ 0.278501] PCI host bridge /soc/pci@20000000 ranges:
[ 0.278527] IO 0x20200000..0x2020ffff -> 0x20200000
[ 0.278545] MEM 0x20220000..0x2fffffff -> 0x20220000
[ 1.425882] qcom-pcie 20000000.pci: phy link never came up
[ 1.427441] qcom-pcie 20000000.pci: hostinit failed
[ 1.427451] qcom-pcie 20000000.pci: cannot initialize host
[ 1.427596] qcom-pcie: probe of 20000000.pci failed with error -110
[ 1.427785] 10000000.pci supply vdda not found, using dummy regulator
[ 1.427825] 10000000.pci supply vdda_phy not found, using dummy regulator
[ 1.427860] 10000000.pci supply vdda_refclk not found, using dummy regulator
[ 1.428445] PCI host bridge /soc/pci@10000000 ranges:
[ 1.428467] IO 0x10200000..0x1020ffff -> 0x10200000
[ 1.428482] MEM 0x10220000..0x1fffffff -> 0x10220000
[ 2.574268] qcom-pcie 10000000.pci: phy link never came up
[ 2.575826] qcom-pcie 10000000.pci: hostinit failed
[ 2.575835] qcom-pcie 10000000.pci: cannot initialize host
[ 2.575945] qcom-pcie: probe of 10000000.pci failed with error -110
[ 2.576332] MDSS QPIC HW Base phy_Address=0x7980000 virt=ffffff80005c0000
[ 2.576712] mdss_qpic_panel_probe: Panel Name = qpic lcd panel
[ 2.578025] mdss_fb_register: FrameBuffer[0] 800x480 registered successfully!
[ 2.581934] msm_rpm_log_probe: OK
[ 2.582272] msm-dcc b3000.dcc: DCC XPU is not specified
[ 2.582606] msm-dcc b3000.dcc: jiffies_64: 0xffff8bd1, cntvct_64: 0xf5afc36
[ 2.582618] msm-dcc b3000.dcc: gcnt_hi: 0x00000000(0xffffff80005bc004)
[ 2.582629] msm-dcc b3000.dcc: gcnt_lo: 0x0f5afe0f(0xffffff80005bc000)
[ 2.583206] TZ SMMU State: SMMU Stage2 Enabled
[ 2.583262] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set
[ 2.584942] msm_serial 78b3000.serial: msm_serial: detected port #0
[ 2.584987] msm_serial 78b3000.serial: uartclk = 3686400
[ 2.585025] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 77, base_baud = 230400) is a MSM
[ 2.585043] msm_serial: console setup on port #0
[ 3.445627] console [ttyMSM0] enabled
[ 3.450666] msm_serial: driver initialized
[ 3.454150] msm_serial_hsl_init: driver initialized
[ 3.467625] brd: module loaded
[ 3.472353] loop: module loaded
[ 3.472986] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[ 3.475869] m25p80 spi32766.0: found w25q64dw, expected n25q128a11
[ 3.481593] m25p80 spi32766.0: w25q64dw (8192 Kbytes)
[ 3.487654] 12 ofpart partitions found on MTD device spi32766.0
[ 3.492699] Creating 12 MTD partitions on "spi32766.0":
[ 3.498448] 0x000000000000-0x000000050000 : "0:SBL1"
[ 3.504443] 0x000000050000-0x000000060000 : "0:MIBIB"
[ 3.509568] 0x000000060000-0x0000001e0000 : "0:QSEE"
[ 3.514506] 0x0000001e0000-0x0000001f0000 : "0:DEVCFG"
[ 3.519554] 0x0000001f0000-0x000000200000 : "0:APDP"
[ 3.524491] 0x000000200000-0x000000240000 : "0:RPM"
[ 3.529615] 0x000000240000-0x000000250000 : "0:CDT"
[ 3.534235] 0x000000250000-0x000000270000 : "0:APPSBLENV"
[ 3.539098] 0x000000270000-0x000000370000 : "0:APPSBL"
[ 3.544651] 0x000000370000-0x0000003b0000 : "0:ART"
[ 3.549702] 0x0000003b0000-0x000000430000 : "0:ETHPHYFW"
[ 3.554444] 0x000000430000-0x000000800000 : "reserved"
[ 3.561046] libphy: Fixed MDIO Bus: probed
[ 4.225047] libphy: qca_mdio: probed
[ 4.233166] qca-mdio 90000.mdio: qca-mdio driver was registered
[ 4.233485] Unable to create IPC log context!
[ 4.238218] Skip QCA8074V1 in V2 platform
[ 4.242640] cnss: Platform driver probed successfully. plat ffffffc03cd7e018 tgt 0xfffe
[ 4.246667] i2c /dev entries driver
[ 4.261768] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[ 4.262282] sdhci: Secure Digital Host Controller Interface driver
[ 4.269292] sdhci: Copyright(c) Pierre Ossman
[ 4.275275] sdhci-pltfm: SDHCI platform and OF driver helper
[ 4.280254] qcom_ice_get_pdevice: invalid device list
[ 4.285432] sdhci_msm 7824900.sdhci: sdhci_msm_ice_get_dev: ICE device not probed yet
[ 4.290366] sdhci_msm 7824900.sdhci: sdhci_msm_probe: required ICE device not probed yet err = -517
[ 4.301065] qcom_ice_get_device_tree_data: No vdd-hba-supply regulator, assuming not needed
[ 4.307115] ICE IRQ = 80
[ 4.315973]
[ 4.315973] Version Rollback Feature Disabled
[ 4.318650] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000008b04000
[ 4.323786] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000008b04000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000008b04000
[ 4.341070] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000008b04000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000008b04000
[ 4.356954] sps:BAM 0x0000000008b04000 is registered.[ 4.366874] remoteproc remoteproc0: releasing cd00000.qcom_q6v5_wcss
[ 4.370169] SPMI VADC - Min ch: 0 Max ch: 15
[ 4.377531] of_graph_get_next_endpoint(): no port node found in /soc/csr@6001000
[ 4.379949] coresight-csr 6001000.csr: CSR initialized
[ 4.387414] of_graph_get_next_endpoint(): no port node found in /soc/cti@6010000
[ 4.392360] of_graph_get_next_endpoint(): no port node found in /soc/cti@6011000
[ 4.399903] of_graph_get_next_endpoint(): no port node found in /soc/cti@6012000
[ 4.407284] of_graph_get_next_endpoint(): no port node found in /soc/cti@6013000
[ 4.414660] of_graph_get_next_endpoint(): no port node found in /soc/cti@6014000
[ 4.422021] of_graph_get_next_endpoint(): no port node found in /soc/cti@6015000
[ 4.429413] of_graph_get_next_endpoint(): no port node found in /soc/cti@6016000
[ 4.436791] of_graph_get_next_endpoint(): no port node found in /soc/cti@6017000
[ 4.444155] of_graph_get_next_endpoint(): no port node found in /soc/cti@6018000
[ 4.451556] of_graph_get_next_endpoint(): no port node found in /soc/cti@6019000
[ 4.458928] of_graph_get_next_endpoint(): no port node found in /soc/cti@601a000
[ 4.466307] of_graph_get_next_endpoint(): no port node found in /soc/cti@601b000
[ 4.473675] of_graph_get_next_endpoint(): no port node found in /soc/cti@601c000
[ 4.481066] of_graph_get_next_endpoint(): no port node found in /soc/cti@601d000
[ 4.488448] of_graph_get_next_endpoint(): no port node found in /soc/cti@601e000
[ 4.495828] of_graph_get_next_endpoint(): no port node found in /soc/cti@601f000
[ 4.503186] of_graph_get_next_endpoint(): no port node found in /soc/cti@6198000
[ 4.510780] of_graph_get_next_endpoint(): no port node found in /soc/cti@6199000
[ 4.518107] of_graph_get_next_endpoint(): no port node found in /soc/cti@619a000
[ 4.525532] of_graph_get_next_endpoint(): no port node found in /soc/cti@619b000
[ 4.532938] of_graph_get_next_endpoint(): no port node found in /soc/cti@610c000
[ 4.540309] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000006044000
[ 4.547326] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000006044000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000006044000
[ 4.564419] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000006044000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000006044000
[ 4.580305] sps:BAM 0x0000000006044000 is registered.[ 4.588069] coresight-tmc 6028000.tmc: TMC initialized
[ 4.592801] coresight-tmc 6027000.tmc: TMC initialized
[ 4.597915] coresight-funnel 6021000.funnel: FUNNEL initialized
[ 4.602919] coresight-funnel 6100000.funnel: FUNNEL initialized
[ 4.608757] coresight-funnel 6120000.funnel: FUNNEL initialized
[ 4.614658] coresight-funnel 6130000.funnel: FUNNEL initialized
[ 4.620553] coresight-funnel 61a1000.funnel: FUNNEL initialized
[ 4.627085] coresight-etm4x 619c000.etm: ETM 4.0 initialized
[ 4.632706] coresight-etm4x 619d000.etm: ETM 4.0 initialized
[ 4.638674] coresight-etm4x 619e000.etm: ETM 4.0 initialized
[ 4.644358] coresight-etm4x 619f000.etm: ETM 4.0 initialized
[ 4.649570] coresight-replicator-qcom 6026000.replicator: REPLICATOR 1.0 initialized
[ 4.655373] coresight-stm 6002000.stm: STM initialized
[ 4.663913] of_graph_get_next_endpoint(): no port node found in /soc/hwevent@6101000
[ 4.667747] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized
[ 4.678430] Netfilter messages via NETLINK v0.30.
[ 4.682959] nf_conntrack version 0.5.0 (6897 buckets, 27588 max)
[ 4.688156] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 4.694419] NET: Registered protocol family 10
[ 4.699686] fullmesh registered
[ 4.703118] NET: Registered protocol family 17
[ 4.706217] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 4.710717] Bridge firewalling registered
[ 4.723451] 8021q: 802.1Q VLAN Support v1.8
[ 4.728977] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 4.731483] pmd9655_s3: supplied by e-smps1-reg
[ 4.738803] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
[ 4.743139] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1
[ 4.749768] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[ 4.757425] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[ 4.764928] cpr3_mem_acc_init: apc: not using memory accelerator regulator
[ 4.774045] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 704000 uV
[ 4.781007] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 808000 uV
[ 4.790987] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 864000 uV
[ 4.800794] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop= 952000 uV
[ 4.810661] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 744, quot_offset[ 7]= 0
[ 4.820417] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 950, quot_offset[ 7]= 205
[ 4.831266] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]=1049, quot_offset[ 7]= 95
[ 4.842205] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]=1216, quot_offset[ 7]= 165
[ 4.853269] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
[ 4.864644] qcom,cpr3-npu-regulator a4000.npu-cpr: NPU CPR valid fuse count: 2
[ 4.870936] pmd9655_s4: supplied by e-smps1-reg
[ 4.878091] cpr3_mem_acc_init: npu: not using memory accelerator regulator
[ 4.882376] npu_corner: fused NOM: open-loop= 784000 uV
[ 4.889330] npu_corner: fused TURBO: open-loop= 848000 uV
[ 4.895186] npu_corner: fused NOM: open-loop= 784000 uV
[ 4.900775] npu_corner: fused TURBO: open-loop= 848000 uV
[ 4.906453] npu_corner: Normal and Cold condition init done. Default to normal.
[ 4.913253] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 800000 KHz
[ 4.919365] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1017600 KHz
[ 4.927002] qcom_ice_get_pdevice: found ice device ffffffc03c4b4400
[ 4.935097] qcom_ice_get_pdevice: matching platform device ffffffc03d6b4400
[ 4.941168] sdhci_msm 7824900.sdhci: No vreg data found for vdd
[ 4.948094] sdhci_msm 7824900.sdhci: No vreg data found for vdd-io
[ 4.954168] qcom_ice 7803000.sdcc1ice: QC ICE 2.1.44 device found @0xffffff8000f6c000
[ 4.961306] sdhci_msm 7824900.sdhci: No vmmc regulator found
[ 4.968139] sdhci_msm 7824900.sdhci: No vqmmc regulator found
[ 5.014216] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit
[ 5.019773] qcom-q6v5-wcss-pil cd00000.qcom_q6v5_wcss: ssr registeration success qcom_q6v5_wcss
[ 5.021053] remoteproc remoteproc0: cd00000.qcom_q6v5_wcss is available
[ 5.031795] hctosys: unable to open rtc device (rtc0)
[ 5.041285] pmd9655_ldo11: disabling
[ 5.041747] ALSA device list:
[ 5.045037] No soundcards found.
[ 5.047926] Warning: unable to open an initial console.
[ 5.051779] Freeing unused kernel memory: 2044K (ffffffc00086c000 - ffffffc000a6b000)
[ 5.056315] Freeing alternatives memory: 44K (ffffffc000a6b000 - ffffffc000a76000)
+ exec
+ mkdir -p /sys /proc
+ echo_dbg Making /sys...
+ echo -e \033[01;32mMaking /sys...\033[00m
Making /sys...
+ mount -t sysfs -o nodev,noexec,nosuid none /sys
+ echo_dbg Making /proc...
+ echo -e \033[01;32mMaking /proc...\033[00m
Making /proc...
+ mount -t proc -o nodev,noexec,n[ 5.097839] mmc0: MAN_BKOPS_EN bit is not set
osuid none /proc
+ wait_detect_emmc
+ local devname=/dev/mmcbl[ 5.108098] mmc0: new HS200 MMC card at address 0001
[ 5.109584] mmcblk0: mmc0:0001 Q2J54A 3.64 GiB
[ 5.114590] mmcblk0rpmb: mmc0:0001 Q2J54A partition 3 512 KiB
[ 5.120138] GPT: device [179:4] (rootfs) set to be root filesystem
[ 5.124669] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9
k0p
+ local emmc_all_partition_exist=1
+ seq 6
+ emmc_all_partition_exist=1
+ [ ! -e /dev/mmcblk0p1 ]
+ emmc_all_partition_exist=0
+ break
+ [ 0 -eq 0 ]
+ sleep 1
+ echo_dbg sleep 1 wait for emmc device /dev/mmcblk0p1
+ echo -e \033[01;32msleep 1 wait for emmc device /dev/mmcblk0p1\033[00m
sleep 1 wait for emmc device /dev/mmcblk0p1
+ seq 6
+ emmc_all_partition_exist=1
+ [ ! -e /dev/mmcblk0p1 ]
+ emmc_all_partition_exist=1
+ [ ! -e /dev/mmcblk0p2 ]
+ emmc_all_partition_exist=1
+ [ ! -e /dev/mmcblk0p3 ]
+ emmc_all_partition_exist=1
+ [ ! -e /dev/mmcblk0p4 ]
+ emmc_all_partition_exist=1
+ [ ! -e /dev/mmcblk0p5 ]
+ emmc_all_partition_exist=1
+ [ ! -e /dev/mmcblk0p6 ]
+ [ 1 -eq 0 ]
+ break
+ [ 1 -eq 0 ]
+ mount_rootfs
+ get_current_fw_entry
+ fw_printenv
+ grep current_entry
+ awk -F= {print $2}
+ local current_entry=1
+ [ x1 = x ]
+ echo 1
+ local current_entry=1
+ local dev_rootfs=
+ [ 1 = 0 ]
+ [ 1 = 1 ]
+ findfs PARTLABEL=rootfs_1
+ dev_rootfs=/dev/mmcblk0p5
+ echo_dbg rootfs boot from rootfs_1
+ echo -e \033[01;32mroo[ 6.448707] EXT4-fs (mmcblk0p5): couldn't mount as ext3 due to feature incompatibilities
[ 6.455143] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null)
tfs boot from rootfs_1\033[00m
rootfs boot from rootfs_1
+ mkdir -p /mnt/rootfs
+ mount -o ro /dev/mmcblk0p5 /mnt/rootfs
+ mount_rootfs_data
+ findfs PARTLABEL=rootfs_data
+ local dev_rootfs_data=/dev/mmcblk0p9
+ echo_dbg rootfs data: /dev/mmcblk0p9
+ echo -e \033[01;32mrootfs data: /dev/mmcblk0p9\033[00m
rootfs data: /dev/mm[ 6.809638] EXT4-fs (mmcblk0p9): couldn't mount as ext3 due to feature incompatibilities
cblk0p9
+ [ x/dev/mmcblk0p9 != x ]
+ [ -e /dev/mmcblk0p9 ]
+ blkid /dev/mmcblk0p9
+ grep -q ext4
+ echo_dbg Mount rootfs data to /mnt/rootfs_data
+ echo -e \033[01;32mMount rootfs data to /mnt/rootfs_data\033[00m
Mount rootfs data to /mnt/rootfs_data
+ mkdir -p /mnt/rootfs_data
+ mount /dev/mmcblk0p9 /mnt/rootfs_data
[ 7.170895] EXT4-fs (mmcblk0p9): recovery complete
[ 7.172219] EXT4-fs (mmcblk0p9): mounted filesystem with ordered data mode. Opts: (null)
+ [ ! -d /mnt/rootfs_data/etc ]
+ [ -e /mnt/rootfs_data/etc/reset_to_default ]
+ mount_usr_squahsfs
+ echo_dbg Mount usr.squahsfs to /mnt/rootfs_data/usr
+ echo -e \033[01;32mMount usr.squahsfs to /mnt/rootfs_data/usr\033[00m
Mount usr.squahsfs to /mnt/rootfs_data/usr
+ [ ! -d /mnt/rootfs_data/usr ]
+ mount -t squashfs -o ro,loop /mnt/rootfs/usr.squashfs /mnt/rootfs_data/usr
+ check_and_restore_ubootenv
+ mount_reserved
+ findfs PARTLABEL=reserved
[ 7.413960] random: nonblocking pool is initialized
+ dev_reserved=/dev/mmcblk0p8
+ echo_dbg reserved partition from reserved
+ echo -e \033[01[ 7.546085] EXT4-fs (mmcblk0p8): couldn't mount as ext3 due to feature incompatibilities
[ 7.552194] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: (null)
;32mreserved partition from reserved\033[00m
reserved partition from reserved
+ mkdir -p /mnt/reserved
+ mount -o ro /dev/mmcblk0p8 /mnt/reserved
+ [ -e /mnt/reserved/uboot-env.bin ]
+ fw_printenv
+ grep BMAC
+ awk -F= {print $2}
+ local BMAC=245EBE530393
+ fw_printenv
+ grep MN
+ awk -F= {print $2}
+ local MN=A03
+ grep QSN
+ fw_printenv
+ awk -F= {print $2}
+ local QSN=Q20BQ01767
+ fw_printenv
+ grep FWMode
+ awk -F= {print $2}
+ local FWMode=Normal
+ [ x245EBE530393 == x ]
+ [ xA03 == x ]
+ [ xQ20BQ01767 == x ]
+ [ xNormal == x ]
+ umount /mnt/reserved
+ get_fw_mode
+ fw_printenv
+ grep FWMode
+ awk -F= {print $2}
+ local FWMode=Normal
+ [ xNormal = x ]
+ echo Normal
+ fw_mode=Normal
+ [ Normal == Normal ]
+ fw_printenv
+ grep ipaddr
+ ipaddr_found=
+ [ x != x ]
+ fw_printenv
+ grep serverip
+ serverip_found=
+ [ x != x ]
+ fw_printenv
+ grep tftptimeoutcountmax
+ tftptimeoutcountmax_found=
+ [ x != x ]
+ echo watchdog close null
+ echo exit 0
+ mount --move /sys /mnt/rootfs_data/sys
+ mount --move /proc /mnt/rootfs_data/proc
+ mount --move /dev /mnt/rootfs_data/dev
+ add_necessary_rootfs
+ [ ! -d /mnt/rootfs_data/run ]
+ mount -t tmpfs tmpfs /mnt/rootfs_data/run
+ [ ! -L /mnt/rootfs_data/var/run ]
+ mkdir -p /mnt/rootfs_data/run/lock
+ [ ! -L /mnt/rootfs_data/var/lock ]
+ [ ! -L /mnt/rootfs_data/etc/rc.common ]
+ [ ! -L /mnt/rootfs_data/etc/preinit ]
+ [ ! -L /mnt/rootfs_data/etc/hotplug-preinit.json ]
+ [ ! -L /mnt/rootfs_data/etc/hotplug.json ]
+ [ false = true ]
+ echo_dbg Switch to real root file system
+ echo -e \033[01;32mSwitch to real root file system\033[00m
Switch to real root file system
+ exec switch_root /mnt/rootfs_data /sbin/init
Part 1
