Hi. I have been trying to install OpenWRT on a Qhora-322 router and was successful for the most part, but got into a weird state with opkg because I moved from the vendor FW to openwrt using a snapshot image. I was trying to explore how to fix this and got into a bad state where the router won't fully boot. It gets stuck at the following step:
/etc/preinit: line 18: uci: not found
I am at a loss of what could be the issue, I would appreciate some pointers. These are the boot logs. I am able to get into initramfs and also the failsafe mode. The guide I was following is this one
U-Boot 2019.10-10.3.4.0-11 (Jun 08 2022 - 17:52:37 +0800)
Model: QHora-322
SoC: cn9132-A1; AP807-B0; 3xCP115-A0
Clock: CPU 2200 [MHz]
DDR 1200 [MHz]
FABRIC 1200 [MHz]
MSS 200 [MHz]
LLC Enabled (Exclusive Mode)
DRAM: 4 GiB
Running in RAM - U-Boot at: 0x7fee9000
Env at: 0x7ff95cc8
Comphy chip #0:
Comphy-0: SATA1
Comphy-1: SGMII2 3.125 Gbps
Comphy-2: SFI0 10.3125 Gbps
Comphy-3: USB3_HOST1
Comphy-4: SGMII1 3.125 Gbps
Comphy-5: PEX2
UTMI PHY 0 initialized to USB Host1
Comphy chip #1:
Comphy-0: IGNORE
Comphy-1: SGMII2 3.125 Gbps
Comphy-2: SFI0 10.3125 Gbps
Comphy-3: IGNORE
Comphy-4: SGMII1 3.125 Gbps
Comphy-5: IGNORE
Comphy chip #2:
Comphy-0: IGNORE
Comphy-1: SGMII2 3.125 Gbps
Comphy-2: SFI0 10.3125 Gbps
Comphy-3: IGNORE
Comphy-4: SGMII1 3.125 Gbps
Comphy-5: IGNORE
PCIE-0: Link down
NAND: 0 MiB
MMC: sdhci@6e0000: 0
Loading Environment from SPI Flash...
Bus spi@700680 CS0 address is not set correct.
SF: Detected mx25l3205d with page size 256 Bytes, erase size 4 KiB, total 4 MiB
OK
RTC_RX8130: original reg[0x1d]:0x2c
RTC_RX8130: modified reg[0x1d]:0x2c
RTC_RX8130: original reg[0x1f]:0x10
RTC_RX8130: modified reg[0x1f]:0x10
Net: eth0: mvpp2-0 [PRIME], eth1: mvpp2-1, eth2: mvpp2-2, eth3: mvpp2-3, eth4: mvpp2-4, eth5: mvpp2-5, eth6: mvpp2-6, eth7: mvpp2-7, eth8: mvpp2-8
Auto-update from TFTP: Skip auto-update, env. variable 'updatefile' not found
Hit any key to stop autoboot: 0
12394504 bytes read in 767 ms (15.4 MiB/s)
47169 bytes read in 15 ms (3 MiB/s)
## Flattened Device Tree blob at 06000000
Booting using the fdt blob at 0x6000000
Using Device Tree in place at 0000000006000000, end 000000000600e840
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083]
[ 0.000000] Linux version 5.15.104 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 12.2.0 r22438-d98c4fb8bf) 12.2.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Mon Mar 27 18:07:54 2023
[ 0.000000] Machine model: iEi Puzzle-M902
[ 0.000000] earlycon: uart8250 at MMIO32 0x00000000f0512000 (options '')
[ 0.000000] printk: bootconsole [uart8250] enabled
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000000000-0x00000000ffffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal [mem 0x0000000100000000-0x000000013fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] node 0: [mem 0x0000000004000000-0x00000000041fffff]
[ 0.000000] node 0: [mem 0x0000000004200000-0x00000000bfffffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000013fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000013fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS resident on physical CPU 0x0
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] percpu: Embedded 16 pages/cpu s26264 r8192 d31080 u65536
[ 0.000000] Detected PIPT I-cache on CPU0
[ 0.000000] CPU features: detected: Spectre-v2
[ 0.000000] CPU features: detected: Spectre-v4
[ 0.000000] CPU features: detected: Spectre-BHB
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1032192
[ 0.000000] Kernel command line: console=ttyS0,115200 earlycon=uart8250,mmio32,0xf0512000 cpuidle.off=1 root=/dev/mmcblk0p3
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: mapped [mem 0x00000000bc000000-0x00000000c0000000] (64MB)
[ 0.000000] Memory: 4041256K/4194304K available (8448K kernel code, 904K rwdata, 2208K rodata, 448K init, 292K bss, 153048K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GIC: Adjusting CPU interface base to 0x00000000f022f000
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv2m: DT overriding V2M MSI_TYPER (base:160, num:32)
[ 0.000000] GICv2m: range[mem 0xf0280000-0xf0280fff], SPI[160:191]
[ 0.000000] GICv2m: DT overriding V2M MSI_TYPER (base:192, num:32)
[ 0.000000] GICv2m: range[mem 0xf0290000-0xf0290fff], SPI[192:223]
[ 0.000000] GICv2m: DT overriding V2M MSI_TYPER (base:224, num:32)
[ 0.000000] GICv2m: range[mem 0xf02a0000-0xf02a0fff], SPI[224:255]
[ 0.000000] GICv2m: DT overriding V2M MSI_TYPER (base:256, num:32)
[ 0.000000] GICv2m: range[mem 0xf02b0000-0xf02b0fff], SPI[256:287]
[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
[ 0.008188] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[ 0.018695] pid_max: default: 32768 minimum: 301
[ 0.023402] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.030894] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.039322] rcu: Hierarchical SRCU implementation.
[ 0.044238] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.052186] smp: Bringing up secondary CPUs ...
[ 0.057137] Detected PIPT I-cache on CPU1
[ 0.057164] CPU1: Booted secondary processor 0x0000000001 [0x410fd083]
[ 0.057558] Detected PIPT I-cache on CPU2
[ 0.057580] CPU2: Booted secondary processor 0x0000000100 [0x410fd083]
[ 0.057964] Detected PIPT I-cache on CPU3
[ 0.057978] CPU3: Booted secondary processor 0x0000000101 [0x410fd083]
[ 0.058006] smp: Brought up 1 node, 4 CPUs
[ 0.094222] SMP: Total of 4 processors activated.
[ 0.099003] CPU features: detected: 32-bit EL0 Support
[ 0.104213] CPU features: detected: CRC32 instructions
[ 0.109438] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.117930] CPU: All CPU(s) started at EL2
[ 0.122118] alternatives: patching kernel code
[ 0.129058] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.139017] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.146053] pinctrl core: initialized pinctrl subsystem
[ 0.151696] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.157909] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
[ 0.165132] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.173033] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.181168] thermal_sys: Registered thermal governor 'step_wise'
[ 0.181469] ASID allocator initialised with 65536 entries
[ 0.200083] cryptd: max_cpu_qlen set to 1000
[ 0.205218] SCSI subsystem initialized
[ 0.209081] usbcore: registered new interface driver usbfs
[ 0.214673] usbcore: registered new interface driver hub
[ 0.220039] usbcore: registered new device driver usb
[ 0.225534] clocksource: Switched to clocksource arch_sys_counter
[ 0.231845] NET: Registered PF_INET protocol family
[ 0.236930] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.245244] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[ 0.253944] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.261792] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.269885] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear)
[ 0.277416] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.284080] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.290859] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.298130] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.303882] PCI: CLS 0 bytes, default 64
[ 0.308303] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[ 0.316113] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.322021] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.332208] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.341999] armada-ap806-pinctrl f06f4000.system-controller:pinctrl: registered pinctrl driver
[ 0.351042] armada-cp110-pinctrl f2440000.system-controller:pinctrl: registered pinctrl driver
[ 0.359976] armada-cp110-pinctrl f4440000.system-controller:pinctrl: registered pinctrl driver
[ 0.368964] armada-cp110-pinctrl f6440000.system-controller:pinctrl: registered pinctrl driver
[ 0.380411] mv_xor_v2 f0400000.xor: Marvell Version 2 XOR driver
[ 0.386759] mv_xor_v2 f0420000.xor: Marvell Version 2 XOR driver
[ 0.393093] mv_xor_v2 f0440000.xor: Marvell Version 2 XOR driver
[ 0.399435] mv_xor_v2 f0460000.xor: Marvell Version 2 XOR driver
[ 0.405804] mv_xor_v2 f26a0000.xor: Marvell Version 2 XOR driver
[ 0.412113] mv_xor_v2 f26c0000.xor: Marvell Version 2 XOR driver
[ 0.418507] mv_xor_v2 f46a0000.xor: Marvell Version 2 XOR driver
[ 0.424841] mv_xor_v2 f46c0000.xor: Marvell Version 2 XOR driver
[ 0.431260] mv_xor_v2 f66a0000.xor: Marvell Version 2 XOR driver
[ 0.437622] mv_xor_v2 f66c0000.xor: Marvell Version 2 XOR driver
[ 0.443778] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.450900] printk: console [ttyS0] disabled
[ 0.475334] f0512000.serial: ttyS0 at MMIO 0xf0512000 (irq = 16, base_baud = 12500000) is a 16550A
[ 0.484469] printk: console [ttyS0] enabled
[ 0.484469] printk: console [ttyS0] enabled
[ 0.492891] printk: bootconsole [uart8250] disabled
[ 0.492891] printk: bootconsole [uart8250] disabled
[ 0.523124] f2702000.serial: ttyS1 at MMIO 0xf2702000 (irq = 53, base_baud = 15625000) is a 16550A
[ 0.532155] serial serial0: tty port ttyS1 registered
[ 0.537503] omap_rng f2760000.trng: Random Number Generator ver. 203b34c
[ 0.537824] random: crng init done
[ 0.544336] omap_rng f4760000.trng: Random Number Generator ver. 203b34c
[ 0.554505] omap_rng f6760000.trng: Random Number Generator ver. 203b34c
[ 0.562512] loop: module loaded
[ 0.565699] Loading iSCSI transport class v2.0-870.
[ 0.571053] ahci f2540000.sata: supply ahci not found, using dummy regulator
[ 0.578200] ahci f2540000.sata: supply phy not found, using dummy regulator
[ 0.585301] platform f2540000.sata:sata-port@0: supply target not found, using dummy regulator
[ 0.594075] platform f2540000.sata:sata-port@1: supply target not found, using dummy regulator
[ 0.603566] spi-nor spi2.0: mx25l3205d (4096 Kbytes)
[ 0.608629] 4 fixed-partitions partitions found on MTD device spi2.0
[ 0.615010] Creating 4 MTD partitions on "spi2.0":
[ 0.619825] 0x000000000000-0x0000001f0000 : "U-Boot"
[ 0.624942] 0x0000001f0000-0x000000200000 : "U-Boot ENV Factory"
[ 0.631083] 0x000000200000-0x0000003f0000 : "Reserved"
[ 0.636350] 0x0000003f0000-0x000000400000 : "U-Boot ENV"
[ 0.650226] hwmon hwmon0: temp1_input not attached to any thermal zone
[ 0.660830] hwmon hwmon1: temp1_input not attached to any thermal zone
[ 0.675636] hwmon hwmon2: temp1_input not attached to any thermal zone
[ 0.686267] hwmon hwmon3: temp1_input not attached to any thermal zone
[ 0.701033] hwmon hwmon4: temp1_input not attached to any thermal zone
[ 0.711624] hwmon hwmon5: temp1_input not attached to any thermal zone
[ 0.719184] mvpp2 f2000000.ethernet: using 8 per-cpu buffers
[ 0.730342] mvpp2 f4000000.ethernet: using 8 per-cpu buffers
[ 0.742449] mvpp2 f6000000.ethernet: using 8 per-cpu buffers
[ 0.754464] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.761026] ehci-pci: EHCI PCI platform driver
[ 0.765506] ehci-platform: EHCI generic platform driver
[ 0.770854] ehci-orion: EHCI orion driver
[ 0.775170] usbcore: registered new interface driver usb-storage
[ 0.781363] armada38x-rtc f2284000.rtc: registered as rtc0
[ 0.786890] armada38x-rtc f2284000.rtc: setting system clock to 2091-02-26T21:17:23 UTC (3823363043)
[ 0.796202] armada38x-rtc f4284000.rtc: registered as rtc1
[ 0.801822] armada38x-rtc f6284000.rtc: registered as rtc2
[ 0.807385] i2c_dev: i2c /dev entries driver
[ 0.866127] sdhci: Secure Digital Host Controller Interface driver
[ 0.872337] sdhci: Copyright(c) Pierre Ossman
[ 0.876777] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.905540] mmc0: SDHCI controller on f06e0000.sdhci [f06e0000.sdhci] using ADMA 64-bit
[ 0.915950] NET: Registered PF_INET6 protocol family
[ 0.921209] Segment Routing with IPv6
[ 0.924895] In-situ OAM (IOAM) with IPv6
[ 0.928859] NET: Registered PF_PACKET protocol family
[ 0.933945] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 0.947004] 8021q: 802.1Q VLAN Support v1.8
[ 0.955876] armada8k-pcie f2640000.pcie: host bridge /cp0/pcie@f2640000 ranges:
[ 0.963231] armada8k-pcie f2640000.pcie: MEM 0x00e1000000..0x00e1efffff -> 0x00e1000000
[ 0.971751] armada8k-pcie f2640000.pcie: iATU unroll: disabled
[ 0.977609] armada8k-pcie f2640000.pcie: Detected iATU regions: 8 outbound, 8 inbound
[ 1.040523] mmc0: new HS400 MMC card at address 0001
[ 1.045813] mmcblk0: mmc0:0001 004GA0 3.69 GiB
[ 1.051992] GPT:Primary header thinks Alt. header is not at the end of the disk.
[ 1.059424] GPT:7372866 != 7733247
[ 1.062839] GPT:Alternate GPT header not at the end of the disk.
[ 1.068873] GPT:7372866 != 7733247
[ 1.072287] GPT: Use GNU Parted to correct GPT errors.
[ 1.077455] mmcblk0: p1 p2 p3 p4 p5 p6 p7
[ 1.081969] mmcblk0boot0: mmc0:0001 004GA0 2.00 MiB
[ 1.087192] mmcblk0boot1: mmc0:0001 004GA0 2.00 MiB
[ 1.092270] mmcblk0rpmb: mmc0:0001 004GA0 512 KiB, chardev (247:0)
[ 1.975533] armada8k-pcie f2640000.pcie: Phy link never came up
[ 1.981523] armada8k-pcie f2640000.pcie: PCI host bridge to bus 0000:00
[ 1.988168] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.993676] pci_bus 0000:00: root bus resource [mem 0xe1000000-0xe1efffff]
[ 2.000596] pci 0000:00:00.0: [11ab:0110] type 01 class 0x060400
[ 2.006635] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[ 2.012959] pci 0000:00:00.0: supports D1 D2
[ 2.017248] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 2.024662] pci 0000:00:00.0: BAR 0: assigned [mem 0xe1000000-0xe10fffff]
[ 2.031488] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 2.651386] pcieport 0000:00:00.0: AER: enabled with IRQ 64
[ 2.657181] ahci f2540000.sata: supply ahci not found, using dummy regulator
[ 2.664301] ahci f2540000.sata: supply phy not found, using dummy regulator
[ 2.671347] platform f2540000.sata:sata-port@0: supply target not found, using dummy regulator
[ 2.680041] platform f2540000.sata:sata-port@1: supply target not found, using dummy regulator
[ 2.689811] ahci f2540000.sata: masking port_map 0x3 -> 0x3
[ 2.695434] ahci f2540000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 2.704001] ahci f2540000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 2.712467] scsi host0: ahci
[ 2.715495] scsi host1: ahci
[ 2.718436] ata1: SATA max UDMA/133 mmio [mem 0xf2540000-0xf256ffff] port 0x100 irq 65
[ 2.726390] ata2: SATA max UDMA/133 mmio [mem 0xf2540000-0xf256ffff] port 0x180 irq 65
[ 2.734592] mvpp2 f2000000.ethernet: using 8 per-cpu buffers
[ 2.958535] mvpp2 f2000000.ethernet eth0: Using firmware node mac address 24:5e:be:7f:96:79
[ 2.969663] mvpp2 f2000000.ethernet eth1: Using firmware node mac address 24:5e:be:7f:96:74
[ 2.980780] mvpp2 f2000000.ethernet eth2: Using firmware node mac address 24:5e:be:7f:96:73
[ 3.009147] mvpp2 f4000000.ethernet: using 8 per-cpu buffers
[ 3.235977] mvpp2 f4000000.ethernet eth3: Using firmware node mac address 24:5e:be:7f:96:7a
[ 3.238428] ata1: SATA link down (SStatus 0 SControl 300)
[ 3.247116] mvpp2 f4000000.ethernet eth4: Using firmware node mac address 24:5e:be:7f:96:76
[ 3.249899] ata2: SATA link down (SStatus 0 SControl 300)
[ 3.260922] mvpp2 f4000000.ethernet eth5: Using firmware node mac address 24:5e:be:7f:96:75
[ 3.295061] mvpp2 f6000000.ethernet: using 8 per-cpu buffers
[ 3.522217] mvpp2 f6000000.ethernet eth6: Using firmware node mac address 24:5e:be:7f:96:7b
[ 3.533389] mvpp2 f6000000.ethernet eth7: Using firmware node mac address 24:5e:be:7f:96:78
[ 3.544537] mvpp2 f6000000.ethernet eth8: Using firmware node mac address 24:5e:be:7f:96:77
[ 3.591083] xhci-hcd f2510000.usb: xHCI Host Controller
[ 3.596343] xhci-hcd f2510000.usb: new USB bus registered, assigned bus number 1
[ 3.603813] xhci-hcd f2510000.usb: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
[ 3.613007] xhci-hcd f2510000.usb: irq 57, io mem 0xf2510000
[ 3.618740] xhci-hcd f2510000.usb: xHCI Host Controller
[ 3.623987] xhci-hcd f2510000.usb: new USB bus registered, assigned bus number 2
[ 3.631419] xhci-hcd f2510000.usb: Host supports USB 3.0 SuperSpeed
[ 3.637882] hub 1-0:1.0: USB hub found
[ 3.641654] hub 1-0:1.0: 1 port detected
[ 3.645675] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.653894] hub 2-0:1.0: USB hub found
[ 3.657671] hub 2-0:1.0: 1 port detected
[ 3.662544] usb_phy_generic cp2_usb3_phy0: dummy supplies not allowed for exclusive requests
[ 3.671112] usb_phy_generic cp2_usb3_phy1: dummy supplies not allowed for exclusive requests
[ 3.681963] VFS: Mounted root (squashfs filesystem) readonly on device 179:3.
[ 3.689234] Freeing unused kernel memory: 448K
[ 3.795584] Run /sbin/init as init process
[ 3.861682] init: Console is alive
[ 3.904458] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.917830] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.925613] init: - preinit -
[ 4.085197] mvpp2 f2000000.ethernet eth0: PHY [f212a600.mdio-mii:02] driver [Aquantia AQR113] (irq=POLL)
[ 4.303812] mvpp2 f2000000.ethernet eth0: configuring for phy/10gbase-r link mode
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.400505] EXT4-fs (mmcblk0p7): warning: maximal mount count reached, running e2fsck is recommended
[ 6.410381] EXT4-fs (mmcblk0p7): recovery complete
[ 6.415594] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: (null). Quota mode: disabled.
[ 6.425745] ext4 filesystem being mounted at /tmp/overlay supports timestamps until 2038 (0x7fffffff)
[ 6.436583] mount_root: switching to ext4 overlay
[ 6.445378] overlayfs: upper fs needs to support d_type.
[ 6.450827] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[ 6.475575] EXT4-fs (mmcblk0p1): mounted filesystem without journal. Opts: (null). Quota mode: disabled.
[ 6.488169] urandom-seed: Seeding with /etc/urandom.seed
/etc/preinit: line 18: uci: not found