Hi xal3xhx,
I also have a router RG-EW3200GX PRO and follow the link: https://openwrt.org/toh/hwdata/ruijie/ruijie_rg-ew3200gx_pro to flash openwrt firmware to this router.
The flashing process is completed, but it cannot boot up. The boot log like as:
UNIVPLL_CON0 = 0xFE000000!!!
mt_pll_init: Set pll frequency for 25M crystal
RAM_CONSOLE preloader last status: 0x0 0x0 0x0 0x0 0x0 0x0
[PMIC_WRAP]wrap_init pass,the return value=0.
[pmic_init] Preloader Start..................
[pmic_init] MT6380 CHIP Code, reg_val = 0, 1:E2 0:E3
[pmic_init] Done...................
Chip part number:7622B
MT7622 Version: 1.2.8, (iPA)
SSC OFF
mt_pll_post_init: mt_get_cpu_freq = 1350000Khz
mt_pll_post_init: mt_get_mem_freq = 1600000Khz
mt_pll_post_init: mt_get_bus_freq = 279980Khz
[PLFM] Init I2C: OK(0)
[BLDR] Build Time: 20210415-111027
==== Dump RGU Reg ========
RGU MODE: 14
RGU LENGTH: FFE0
RGU STA: 40000000
RGU INTERVAL: FFF
RGU SWSYSRST: 8000
==== Dump RGU Reg End ====
RGU: g_rgu_satus:2
mtk_wdt_mode_config mode value=10, tmp:22000010
PL RGU RST: ??
SW reset with bypass power key flag
Find bypass powerkey flag
WDT NONRST=0x20000000
WDT IRQ_EN=0x340003
RGU mtk_wdt_init:MTK_WDT_DEBUG_CTL(590200F3)
[EMI] MDL number = 2
[EMI] DRAMC calibration start
[EMI] DRAMC calibration end
[EMI]rank size auto detect
[EMI]start_addr[0x40000000]=0x12345678, test_addr[0x48000000]= 0xEDCBA987
[EMI]start_addr[0x40000000]=0xEDCBA987, test_addr[0x50000000]= 0xEDCBA987
[EMI]rank0 size: 0x10000000
[MEM] complex R/W mem test pass
RAM_CONSOLE wdt status (0x2)=0x2
Flash Index: 0, MenuID: 0x20, DevID1: 0x40, DevID2: 0x18
Read flash id fail, apply shadow flash parameters.
Roger debug: size=1000000, flash_num=1
Flash #0: write protect disable successfully!
Flash #0: write protect enable successfully
size = 1000000, exit 4 byte mode
[PLFM] Init Boot Device: OK(0)
[PART] blksz: 1B
[PART] [0x0000000000000000-0x000000000001FFFF] "PRELOADER" (131072 blocks)
[PART] [0x0000000000020000-0x000000000002FFFF] "tee1" (65536 blocks)
[PART] [0x0000000000030000-0x000000000006FFFF] "lk" (262144 blocks)
Device APC domain init setup:
Domain Setup (0x0)
Domain Setup (0x0)
Device APC domain after setup:
Domain Setup (0x0)
Domain Setup (0x0)
read len: 8192
[do_read_image_blks] This is a FIT image,img_size = 0x1e9994
[do_read_image_blks] img_blks = 0x1e9994
[do_read_image_blks] img_align_size = 0x1e9994
read len: 2005396
bootm flag=0, states=70f
## Loading kernel from FIT Image at 4007ff28 ...
Bad FIT kernel image format!
ERROR: can't get kernel image!
Can you give me some advice on this error?
Thank you,