Request: OpenWrt on Tilgin 2381

Hi
I have a Tilgin 2831 (labeled "tilgin 2381_EU") on my spare router shelf. I'd really like to have OpenWrt on it, but the model is not in the supported devices list.
I was hoping that someone here could help out to somehow learn me the procedure of getting this done.
So far i've grabbed the following on the UART pins: (part1/2)

ROM VER: 1.0.0
CFG 06
NAND

ROM VER: 1.0.0
CFG 06
NAND

DDR autotuning Rev 1.0
DDR size from 0xa0000000 - 0xa3ffffff
DDR check ok... start booting...



Tilgin UBI HG228x/238x U-Boot 2010.06-LANTIQ-v-2.3.10 (Mar 09 2015 - 22:07:17) 02_07_00_42

CLOCK CPU 720M RAM 360M
16 Bit RAM
DRAM:  128 MiB
NAND:  NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Macronix NAND 128MiB 3,3V 8-bit)
128 MiB
Creating 1 MTD partitions on "nand0":
0x000000000000-0x000000080000 : "U-Boot"
Creating 1 MTD partitions on "nand0":
0x000000080000-0x000008000000 : "ubi"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: max. sequence number:       13131
UBI: attached mtd2 to ubi0
UBI: MTD device name:            "ubi"
UBI: MTD device size:            127 MiB
UBI: number of good PEBs:        1018
UBI: number of bad PEBs:         2
UBI: number of corrupted PEBs:   0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    256
UBI: number of internal volumes: 1
UBI: number of user volumes:     13
UBI: available PEBs:             689
UBI: total number of reserved PEBs: 329
UBI: number of PEBs reserved for bad PEB handling: 10
UBI: max/mean erase counter: 268/13
UBI: image sequence number:  1377090127
Volume Environment (ID 4) found at slot 4
Read 7936 bytes from volume 4 to 86c332a8(buf address)
In:    serial
Out:   serial
Err:   serial
Board reset caused by unknown (3c08a060).

Net:   internal phy using 25Mhz clock
Internal phy firmware version: 0x8434
PHY version 8435
ar10 Switch

Type "run flash_flash" to start the Linux kernel

Hit any key to stop autoboot:  0 

No private boot packet is detected
Volume kernel (ID 7) found at slot 7
Read 0 bytes from volume 7 to 80500000(buf address)
Read [1417059] bytes
## Booting kernel from Legacy Image at 80500000 ...
   Image Name:   MIPS Linux-2.6.32
   Created:      2016-12-01  21:23:11 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1416995 Bytes = 1.4 MiB
   Load Address: 80002000
   Entry Point:  80006150
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

Lantiq xDSL CPE GRX390
mips_hpt_frequency = 360000000, counter_resolution = 2
Linux version 2.6.32.42 (lajo@tilgin00144) (gcc version 4.3.3 (GCC) ) #1 Thu Dec 1 22:23:02 CET 2016
printk buffer from the previous boot:

-----------------------------------
 ä "9J
`àê@&H
"UPäTuYA È
-----------------------------------
phym = 08000000, mem = 07f00000, max_pfn = 00007f00
Reserving memory for CP1 @0xa7f00000, size 0x00100000
CPU revision is: 00019556 (MIPS 34Kc)
Determined physical RAM map:
AR10 mem final size = 3207168
AR10 mem final size = 5177344
AR10 mem final size = 107999232
User-defined physical RAM map:
 memory: 0030f000 @ 00000000 (usable)
 memory: 004f0000 @ 00410000 (usable)
 memory: 066ff000 @ 00a01000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00007100
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
    0: 0x00000000 -> 0x0000030f
    0: 0x00000410 -> 0x00000900
    0: 0x00000a01 -> 0x00007100
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 28188
Kernel command line: mtdparts=ifx_nand:0x80000@0x0(U-Boot),-@0x80000(ubi) ubi.mtd=ubi root=mtd:rootfs ip=192.168.1.1:192.168.1.3::::eth0:on console=ttyS0,115200 ethaddr=00:02:61:BA:50:80 ID_ProductID=HG2381 ID_MAC_0=00:02:61:BA:50:80 ID_MAC_1=00:02:61:BA:50:81 ID_MAC_2=00:02:61:BA:50:82 ID_MAC_3=00:02:61:BA:50:83 ID_MAC_4=00:02:61:BA:50:84 ID_MAC_5=00:02:61:BA:50:85 ID_MAC_6=00:02:61:BA:50:86 ID_MAC_7=00:02:61:BA:50:87 panic=1 UBOOT_VERSION="02_07_00_42" UBOOT_DATETIME="Mar 9 2015 - 22:07:37" RESET_CAUSE=unknown boot_cond=0 vpe1_load_addr=0x87f00000 vpe1_mem=1M wlanm=126 mem=0x40f000 mem=0x5f0000@0x410000 mem=0x67ff000@0xa01000
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=0005f4f0
Readback ErrCtl register=0005f4f0
Memory: 108696k/113656k available (3048k kernel code, 4784k reserved, 1119k data, 192k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:185
Lantiq ICU driver, version 3.0.1, (c) 2001-2013 Lantiq Deutschland GmbH
console [ttyS0] enabled
Calibrating delay loop... 478.41 BogoMIPS (lpj=2392064)
Security Framework initialized
Mount-cache hash table entries: 512
NET: Registered protocol family 16


  |      |
 ~|~~~ | | ,~~~~. | ,~~~~.
  |    | | |    | | |    |
  `~~` ' ' `~~~ ; ' '    '
            ~~~~
 Home gateway product HG2381


Registered platform device tilgin-hg-ltq-nand:-1
Registered platform device tilgin-hg-ltq-gphy:-1
Registered platform device ar10-ssi0:-1
Registered platform device ar10-mdio:-1
Registered platform device danube-ledc-gpo:-1
Registered platform device on-off-sw-gpio:0
Registered platform device on-off-sw-gpio:2
Registered platform device on-off-sw-gpio:3
Registered platform device on-off-sw-gpio:4
Registered platform device leds-gpio:5
Registered platform device ar10-usif:-1
Registered platform device on-off-sw-gpio:1
Registered platform device cosic-catiq:-1
!!!!!!! WAVE400 system registeration on AHB 
MTLK_MEM_BAR0_START is 7e00000
MTLK_MEM_BAR0_END is 7efffff
MTLK_MEM_BAR1_START is 1a000000
MTLK_MEM_BAR1_END is 1a7fffff
MTLK_WIRELESS_IRQ_IN_INDEX is 18
Lantiq Danube/Twinpass/Vinax GPIO
danube-gpio danube-gpio.0: gpio_base=0
danube-gpio danube-gpio.1: gpio_base=16
danube-gpio danube-gpio.2: gpio_base=32
Lantiq Danube/Twinpass/Vinax LED controller GPO
danube-ledc-gpo danube-ledc-gpo: gpio_base=64
On/off switch class
GPIO-based on/off switch with auto-off
Registered on/off switch device: slic_reset
Registered on/off switch device: usb_power
Registered on/off switch device: pcie0_rst
Registered on/off switch device: pcie2_rst
Registered on/off switch device: cosic_reset
ifx_pcie_wait_phy_link_up port 0 timeout
ifx_pcie_wait_phy_link_up port 0 timeout
ifx_pcie_wait_phy_link_up port 0 timeout
ifx_pcie_wait_phy_link_up port 0 timeout
ifx_pcie_wait_phy_link_up port 0 timeout
pcie_rc_initialize port 0 link up failed!!!!!
on/off switch 'pcie1_rst' not found
Lantiq PCIe Root Complex driver, version 2.0.0, (c) 2001-2013 Lantiq Deutschland GmbH
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ifx_pcie_rc_class_early_fixup port 2: fixed pcie host bridge to pci-pci bridge
pci 0000:00:00.0: PME# supported from D0 D3hot
pci 0000:00:00.0: PME# disabled
pci 0000:01:00.0: PME# supported from D0 D1 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:00:00.0: PCI bridge, secondary bus 0000:01
pci 0000:00:00.0:   IO window: disabled
pci 0000:00:00.0:   MEM window: 0x1b000000-0x1b1fffff
pci 0000:00:00.0:   PREFETCH window: 0x1b200000-0x1b2fffff
NET: Registered protocol family 8
NET: Registered protocol family 20
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
gptu: totally 6 16-bit timers/counters
gptu: misc_register on minor 63
gptu: succeeded to request irq 118
gptu: succeeded to request irq 119
gptu: succeeded to request irq 120
gptu: succeeded to request irq 121
gptu: succeeded to request irq 122
gptu: succeeded to request irq 123
IFX DMA driver, version ifxmips_dma_core.c:v1.1.5 
,(c)2009 Infineon Technologies AG
Lantiq CGU driver, version 1.1.38, (c) 2001-2013 Lantiq Deutschland GmbH
vpe1_mem = 100000
Wired TLB entries for Linux read_c0_wired() = 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Squashfs 2.2-r2 (released 2005/09/08) (C) 2002-2005 Phillip Lougher
msgmni has been set to 212
alg: No test for stdrng (krng)
Infineon Technologies DEU driver version 2.0.0 
Lantiq Technologies DEU Driver version 2.0.0
alg: cipher: setkey failed on test 5 for ifxdeu-des: flags=100
alg: skcipher: setkey failed on test 5 for ifxdeu-ecb(des): flags=100
alg: cipher: setkey failed on test 1 for ifxdeu-des3_ede: flags=200000
IFX DEU DES initialized (multiblock).
Lantiq Technologies DEU Driver version 2.0.0
IFX DEU AES initialized (multiblock).
Infineon Technologies DEU driver version 2.0.0 
IFX DEU ARC4 initialized (multiblock).
Infineon Technologies DEU driver version 2.0.0 
IFX DEU SHA1 initialized.
Infineon Technologies DEU driver version 2.0.0 
IFX DEU MD5 initialized.
Infineon Technologies DEU driver version 2.0.0 
Key length exceeds maximum key length
alg: hash: setkey failed on test 5 for ifxdeu-sha1_hmac: ret=22
IFX DEU SHA1_HMAC initialized.
Infineon Technologies DEU driver version 2.0.0 
alg: hash: setkey failed on test 5 for ifxdeu-md5_hmac: ret=22
IFX DEU MD5_HMAC initialized.
DEU driver initialization complete!
io scheduler noop registered (default)
I/O Memory GPIO Emulation
ifx_pmu_init: Major 253
Lantiq PMU driver, version 1.2.6, (c) 2001-2013 Lantiq Deutschland GmbH
Lantiq GPIO driver, version 1.3.2, (c) 2001-2013 Lantiq Deutschland GmbH
Infineon Technologies RCU driver version 1.1.1 
tilgin-hg-ltq-gphy tilgin-hg-ltq-gphy: Lantiq GPHY kthread created
tilgin-hg-ltq-gphy tilgin-hg-ltq-gphy: gpio_base=96
Tilgin initialization is OK
ttyS0 at MMIO 0xbe100c00 (irq = 105) is a IFX_ASC
Lantiq ASC (UART) driver, version 1.0.14, (c) 2001-2013 Lantiq Deutschland GmbH
loop: module loaded
slram: not enough parameters.
Tilgin HG Lantiq NAND driver
ifx_nand_init
Probe for NAND flash...
Checking if ONFI complient
NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Macronix NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 44 at 0x000000580000
Bad eraseblock 1020 at 0x000007f80000
2 cmdlinepart partitions found on MTD device ifx_nand
Creating 2 MTD partitions on "ifx_nand":
0x000000000000-0x000000080000 : "U-Boot"
0x000000080000-0x000008000000 : "ubi"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: max. sequence number:       13131
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "ubi"
UBI: MTD device size:            127 MiB
UBI: number of good PEBs:        1018
UBI: number of bad PEBs:         2
UBI: number of corrupted PEBs:   0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    256
UBI: number of internal volumes: 1
UBI: number of user volumes:     13
UBI: available PEBs:             689
UBI: total number of reserved PEBs: 329
UBI: number of PEBs reserved for bad PEB handling: 10
UBI: max/mean erase counter: 268/13
UBI: image sequence number:  1377090127
UBI: background thread "ubi_bgt0d" started, PID 242
Lantiq SSC driver, version 2.4.2, (c) 2001-2013 Lantiq Deutschland GmbH
Lantiq USIF-SPI driver, version 1.3.2, (c) 2001-2013 Lantiq Deutschland GmbH
PPP generic driver version 2.4.2
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
Lantiq PCIe EP  driver, version 1.0.1, (c) 2001-2013 Lantiq Deutschland GmbH
IFX SWITCH API, Version 1.2.6
SWAPI: Registered character device [switch_api] with major no [81]
Switch API: PCE MicroCode loaded !!
GPHY FW load for ARX300 !!
Lantiq GPHY #0 in GE mode
Lantiq GPHY #1 in GE mode
Lantiq GPHY #2 in GE mode
Lantiq GPHY #3 in GE mode
IFX GPHY driver version ifxmips_xrx_gphy: V1.1.1 - Firmware: GPHY0 GE 8435, GPHY1 GE 8435, GPHY2 GE 8435, GPHY3 GE 8435
res = 86d2e400
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
input: input-gpio-polled as /devices/platform/input-gpio-polled.0/input/input0
Lantiq Danube/Twinpass/Vinax Watchdog
danube-wdt danube-wdt: Starting Watchdog Timer
Start watchdog with maximum timeout 44 seconds
Registered led device: 1:green
Registered led device: 3:green
Registered led device: 3:red
Registered led device: 4:green
Registered led device: 4:red
Registered led device: 5:green
Registered led device: 5:red
Registered led device: 6:red
Registered led device: 6:green
Registered led device: 7:red
Registered led device: 7:green
Registered led device: 8:red
Registered led device: 8:green
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1701 buckets, 6804 max)
ctnetlink v0.93: registering with nfnetlink.
nf_ct_ipsec_ike: registering helper for pf: 2 port: 500
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
Bridge firewalling registered
Ebtables v2.0 registered
KOAM is loaded successfully.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
tilgin-hg-ltq-gphy tilgin-hg-ltq-gphy: switch port #1 PHY ID is 0x1
tilgin-hg-ltq-gphy tilgin-hg-ltq-gphy: switch port #2 PHY ID is 0x2
tilgin-hg-ltq-gphy tilgin-hg-ltq-gphy: switch port #3 PHY ID is 0x3
tilgin-hg-ltq-gphy tilgin-hg-ltq-gphy: switch port #4 PHY ID is 0x4
tilgin-hg-ltq-gphy tilgin-hg-ltq-gphy: switch port #5 PHY ID is 0x5
Firmware version for port 1 is 435 - may be it's timeto enable power saving?
Firmware version for port 2 is 435 - may be it's timeto enable power saving?
Firmware version for port 3 is 435 - may be it's timeto enable power saving?
Firmware version for port 4 is 435 - may be it's timeto enable power saving?
Firmware version for port 5 is 435 - may be it's timeto enable power saving?
Use /dev/mtdblock2 instead of mtd:rootfs
VFS: Mounted root (squashfs_old filesystem) readonly on device 31:2.
Freeing unused kernel memory: 192k freed
init started: BusyBox v1.21.1 (2016-12-01 22:27:29 CET)
starting pid 311, tty '': '/etc/init.d/rcS'
real	0m 0.02s
user	0m 0.00s
sys	0m 0.02s
crm-cleanup: running...
iptables v1.4.6: can't initialize iptables table `mangle': Table does not exist (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
iptables v1.4.6: can't initialize iptables table `mangle': Table does not exist (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
grep: /proc/597/cmdline: No such file or directory
grep: /proc/613/cmdline: No such file or directory
All modules unloaded
crm-cleanup: done
pmem-name2path: Failed to map MTD device 'Environment2'
pmem-read.squashfs: Restoring /var/log from Log (/dev/mtd/4)
mount: mounting /dev/mtdblock/4 on /tmp/pmem.Vp3p1I failed: Invalid argument
mount: mounting /dev/mtdblock/8 on /tmp/pmem.9WEFal failed: Invalid argument
cat: can't open '/tmp/pmem.9WEFal/VERSION': No such file or directory
pmem-read.squashfs: Failed to read Config-A version file
pmem-name2path: Failed to map MTD device 'Config-B'
pmem-read.squashfs: Restoring /var/etc from Config-A (/dev/mtd/8)
mount: mounting /dev/mtdblock/8 on /tmp/pmem.9WEFal failed: Invalid argument
pmem-read.squashfs: Restoring /tmp/pmem.uYBBhB from Config-C (/dev/mtd/3)
mount: mounting /dev/mtdblock/3 on /tmp/pmem.9WEFal failed: Invalid argument
pmem-name2path: Failed to map MTD device 'Environment2'
pmem-name2path: Failed to map MTD device 'rootfs-ram'
pmem-name2path: Failed to map MTD device 'appfs-ram'
pmem-read.squashfs: Restoring /var/miscA from Misc-A (/dev/mtd/14)
mount: mounting /dev/mtdblock/14 on /tmp/pmem.NG6QwY failed: Invalid argument
pmem-name2path: Failed to map MTD device 'Misc-B'
pmem-name2path: Failed to map MTD device 'Config-B'
Jan  1 00:00:16 C Dispatcher: Init module logger	OK

(Part2/2)

RootFS version ESx003-02_07_05_14


BusyBox v1.21.1 (2016-12-01 22:27:29 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.

Retrieved safe mode threat limit 5
# Trying to start watchdog with timeout 10 seconds
umount: can't umount /usr/share/webui: Invalid argument
IFXUSB: ifxusb_hcd: version 3.2 B140220-tilgin271015
IFXUSB:    OPTION: __IS_AR10__
IFXUSB:    OPTION: __UEIP__
IFXUSB:    OPTION: __PHY_LONG_PREEMP__
IFXUSB:    OPTION: __UNALIGNED_BUF_ADJ__
IFXUSB:    OPTION: __ENABLE_DUMP__
IFXUSB:    OPTION: __NEW_COC__
IFXUSB:    OPTION: __IS_HOST__
IFXUSB:            __IS_DUAL__
IFXUSB:            __DYN_SOF_INTR__
IFXUSB:            __UEIP__
IFXUSB:            __DO_OC_INT__
IFXUSB:            __INTRNAKRETRY__
IFXUSB:            __INTRINCRETRY__
IFXUSB: USB core #0 soft-reset
IFXUSB: USB core #0 soft-reset
ifxusb_hcd ifxusb_hcd: IFX USB Controller
ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
ifxusb_hcd ifxusb_hcd: irq 54, io mem 0xbe101000
IFXUSB: Init: Power Port (0)
on/off switch 'usb1_power' not found
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
IFXUSB: USB core #1 soft-reset
IFXUSB: USB core #1 soft-reset
ifxusb_hcd ifxusb_hcd: IFX USB Controller
ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 2
ifxusb_hcd ifxusb_hcd: irq 83, io mem 0xbe106000
IFXUSB: Init: Power Port (0)
on/off switch 'usb2_power' not found
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
cryptodev: module license 'BSD' taints kernel.
Disabling lock debugging due to kernel taint
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
usbcore: registered new interface driver usblp
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver rndis_host
usbcore: registered new interface driver cdc_ncm
[4294692186] mtlk0(mtlk_cdev_init:355): Max nodex set to 1048575
[4294693296] mtlk0(__mtlk_print_endianess:4915): The system is Big endian (0xbeadfeed, 0xedfeadbe)
[4294693296] mtlk<3>(_ahb_irq_get:429): Found device IRQ: 18
[4294693306] mtlk0(_mtlk_df_user_alloc_devname:8455): NDEV Name pattern: wlan%d
[4294693316] mtlk0(mtlk_core_pdb_fast_handles_open:44): Open Hot-path parameters
[4294693316] mtlk<4>(_mtlk_mmb_cleanup_reset_mac:3245): FW CPU reset is done
[MTLKD] BBCPU Reg: offs=0x01c0 (ba2f01c0) val=0xfff007e0 (offset_mb=126)
[MTLKD] Enabling interrupt (bf880208)
[MTLKD] Interrupt enabled
[MTLKD] ChipID: 0x07D0
[MTLKD] e-fuse: num 1, address 0xbf1073b0, word: 0x00000000, value: 0x000
[MTLKD] e-fuse: num 2, address 0xbf1073b4, word: 0x00000000, value: 0x000
[MTLKD] e-fuse: num 3, address 0xbf1073b8, word: 0x00000000, value: 0x000
[MTLKD] e-fuse: num 4, address 0xbf1073bc, word: 0x00000000, value: 0x000
[MTLKD] e-fuse: num 5, address 0xbf1073c0, word: 0x00000000, value: 0x000
[MTLKD] e-fuse: num 6, address 0xbf1073c4, word: 0x00000000, value: 0x000
mtlk mtlk.0: firmware: requesting cal_wlan0.bin
[4294693506] mtlk0(mtlk_mmb_drv_get_cpu_freq:604): FPI bus frequency: 360 MHz
mtlk mtlk.0: firmware: requesting ap_upper_ar10.bin
[4294693736] mtlk0(get_firmware_version:1161): CID-0000: ap_upper_ar10.bin: @@@ VERSION INFO @@@ version number: 3.4.2.40.05_NoPsTxCancel_2_r4540 MIPS:  Single CPU(TMC AGG AP) interface: PCI  phy type: real phy on Dec 31 2014 at 14:19:47@@@ END @@@

[4294693816] mtlk<4>(_mtlk_mmb_send_hw_dep_cfg:2443): AFE value: 0x23056012
[4294693846] mtlk0(mtlk_eeprom_check_ee_data:1353): Options mask is 0x00
[4294693846] mtlk0(load_default_hw_table:2119): HW configuration is 2X2
[4294694046] mtlk0(_mtlk_core_mbss_add_vap:7757): CID-0000: Got PRM_ID_VAP_ADD
[4294694056] mtlk0(_mtlk_df_user_alloc_devname:8455): NDEV Name pattern: wlan0.0
[4294694066] mtlk0(mtlk_core_pdb_fast_handles_open:44): Open Hot-path parameters
[4294694086] mtlk0(_mtlk_core_mbss_add_vap:7775): CID-0000: VAP#1 added
[4294694126] mtlk0(_mtlk_core_mbss_add_vap:7757): CID-0000: Got PRM_ID_VAP_ADD
[4294694126] mtlk0(_mtlk_df_user_alloc_devname:8455): NDEV Name pattern: wlan0.1
[4294694136] mtlk0(mtlk_core_pdb_fast_handles_open:44): Open Hot-path parameters
[4294694176] mtlk0(_mtlk_core_mbss_add_vap:7775): CID-0000: VAP#2 added
[4294694226] mtlk0(_mtlk_core_mbss_add_vap:7757): CID-0000: Got PRM_ID_VAP_ADD
[4294694226] mtlk0(_mtlk_df_user_alloc_devname:8455): NDEV Name pattern: wlan0.2
[4294694236] mtlk0(mtlk_core_pdb_fast_handles_open:44): Open Hot-path parameters
[4294694286] mtlk0(_mtlk_core_mbss_add_vap:7775): CID-0000: VAP#3 added
Loading D5 (MII0/1) driver ...... 
CHIPID: 1, chipid address: 0xbf107344
Succeeded!
PPE datapath driver info:
  Version ID: 128.3.3.1.2.14.1
  Family    : AR10
  DR Type   : Normal Data Path | Indirect-Fast Path
  Interface : MII0 | MII1
  Mode      : Routing
  Release   : 2.14.1
PPE firmware info:
  Version ID: 10.5.2.14.3
  Family    : GRX390
  FW Package: D5
  Release   : 2.14.3
PPE firmware feature:
  Packet Acceleration             Support
  IPv4                            Support
  IPv6                            Support
  6RD                             Support
  DS-Lite                         Support
PPA API --- init successfully
ifx_ppa_init - init succeeded
ifx_ppa_init - init succeeded
IFXOS, Version 1.5.16 (c) Copyright 2009, Lantiq Deutschland GmbH
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_pci: 10.2.85 (Atheros/multi-bss)
ath_pci_probe
PCI device id is 003c :003c
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
ath_pci 0000:01:00.0: ath DEBUG: sc=0x855d7200

 ol_ath_pci_configure : num_desired MSI set to 0

 Using PCI Legacy Interrupt
__ol_ath_attach: ath_attach TODO
__ol_ath_attach: dev name wifi0
ol_ath_attach() BMI inited.
ol_ath_attach() BMI Get Target Info.
ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016c
NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0
ol_ath_attach() configure Target .
Reading Flash for Calibraton data from 0x5000 and partition name is caldata
TILGIN ol_transfer_bin_file OS_NAND_FLASH_READ at 20480 (2116) OK
qc98xx_verify_checksum: flash checksum passed: 0xe0f3
ol_transfer_bin_file 1804: Download Flash data len 2116
ol_transfer_bin_file 1748: Download Firmware data len 218164
ol_ath_attach() Download FW. 
ol_ath_attach() HT Create .
ol_ath_attach() HIF Claim.
ol_ath_attach() BMI Done. 
ol_ath_attach() WMI attached. wmi_handle 85750000 
+HWT
CE_recv_buf_enqueue 625 Populate last entry 512 for CE 5
CE_recv_buf_enqueue 634 CE 5 wi 511 dest_ptr 0x46d8840 nbytes 0 recv_ctxt 0x846d68c0
-HWT
HTC Service:0x0300 ep:1 TX flow control disabled
CE_pkt_dl_len_set CE 4 Pkt download length 64
HTC Service:0x0100 ep:2 TX flow control disabled
wmi_service_ready_event_rx:  WMI UNIFIED SERVICE READY event 
num_rf_chain : 00000003
ht_cap_info: : 0000085b
vht_cap_info : 338001b2
vht_supp_mcs : 0000ffea
LARGE_AP enabled. num_peers 144, num_vdevs 16, num_tids 256
idx 0 req 1  num_units 0 num_unit_info 2 unit size 408 actual units 145 
chunk 0 len 59160 requested ,ptr  0x56e0000 
FIRMWARE:P 145 V 16 T 443
 
FIRMWARE:_wlan_rtt_enable 
wmi_ready_event_rx:  WMI UNIFIED READY event 
ol_ath_connect_htc() WMI is ready
ol_ath_set_host_app_area TODO
target uses HTT version 2.1; host uses 2.1
ol_ath_attach() connect HTC. 
ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
Add VHT80 channel: 5210
Add VHT80 channel: 5290
Add VHT80 channel: 5530
Add VHT80 channel: 5610
Add VHT80 channel: 5690
Add VHT80 channel: 5775
Skipping VHT80 channel 5825
ol_ath_phyerr_attach: called
OL Resmgr Init-ed
ol_if_dfs_setup: called 
ol_if_dfs_attach: called; ptr=84701974, radar_info=855cdc08
ol_ath_rtt_meas_report_attach: called
ol_ath_attach() UMAC attach . 
ol_if_dfs_configure: called
ol_if_dfs_configure: FCC domain
ol_if_dfs_disable: called
ol_ath_attach: Calling ol_if_dfs_configure
__ol_ath_attach: init tx/rx TODO
__ol_ath_attach: hard_header_len reservation 58
Initializing Pktlogs for 11ac
ath_ioctl: SIOC80211IFCREATE CALLED
wmi_unified_vdev_create_send: ID = 0 VAP Addr = 00:02:61:ba:50:85:
Getting Nss: 3
ieee80211_dfs_override_cac_timeout: CAC timeout is now overridden (2)
watchdog: disabled
Trying to start watchdog with timeout 10 seconds
ifx_ppa_init - init succeeded
[4294707376] mtlk0(_mtlk_df_user_ppa_register:616): PPA device function is registered (id=3)
device eth0 entered promiscuous mode
device wlan0 entered promiscuous mode
isCountryCodeValid: EEPROM regdomain 0x0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
Add VHT80 channel: 5210
Add VHT80 channel: 5290
Add VHT80 channel: 5530
Add VHT80 channel: 5610
Skipping VHT80 channel 5660
Skipping VHT80 channel 5680
Skipping VHT80 channel 5700
OL vap_stop +
wmi_unified_vdev_stop_send 
OL vap_stop -
STOPPED EVENT for vap 0 
OL vap_stop +
wmi_unified_vdev_stop_send 
OL vap_stop -
STOPPED EVENT for vap 0 
Too long sleep: 5 vs 2
ath_ioctl: SIOC80211IFCREATE CALLED
wmi_unified_vdev_create_send: ID = 0 VAP Addr = 00:02:61:ba:50:85:
Mem: 47220K used, 61844K free, 0K shrd, 5656K buff, 19784K cached
CPU:  45% usr  54% sys   0% nic   0% idle   0% io   0% irq   0% sirq
Load average: 1.52 0.35 0.11 5/51 2086
  PID  PPID USER     STAT   VSZ %VSZ %CPU COMMAND
  684   531 root     R    12416  11%  36% crm -t -f /var/log/crm.log
 2072  2071 root     R <   1856   2%   9% top -b -n 1
 1803   684 root     S     8032   7%   0% drvhlpr -p /tmp/drvhlpr0.conf -e 2
 2032   684 root     S <   3600   3%   0% watchdog --crm-timeout 180 --wdt-timeout 10
 1391  1386 root     S     1864   2%   0% {crm-hotplug} /bin/sh /usr/bin/crm-hotplug usb
 1436  1431 root     S     1864   2%   0% {crm-hotplug} /bin/sh /usr/bin/crm-hotplug usb
 1286   684 root     S     1860   2%   0% /bin/sh --login
    1    OL vap_stop +
 wmi_unified_vdev_stop_send 
OL vap_stop -
STOPPED EVENT for vap 0 
0 root     S     1856   2%   0% init
  531     1 root     S     1856   2%   0% {crm-keeper} /bin/sh /usr/bin/crm-keeper
 1226     OL vap_stop +
wmi_unified_vdev_stop_send 
OL vap_stop -
STOPPED EVENT for vap 0 
1 root     S     1856   2%   0% syslogd -O /var/log/crm.log -s 200
 1386     6 root     S     1856   2%   0% {crm-hotplug} /bin/sh /usr/bin/crm-hotplug usb
 2071  2032 root     S <   1856   2%   0% /bin/sh -c top -b -n 1
 1431     6 root     S     1856   2%   0% {crm-hotplug} /bin/sh /usr/bin/crm-hotplug usb
 2081     6 root     S     1856   2%   0% {crm-hotplug} /bin/sh /usr/bin/crm-hotplug net
 1224     1 root     S     1848   2%   0% klogd
 1404  1391 root     S     1552   1%   0% caction -u hotplug.usb /usb/host/updPPA REG DONE, if_id=4, dev_if_index = 12, os_unit=0 
ate_led
 1449  1436 root     S     1552   1%   0% caction -u hotplug.usb /usb/host/update_led
 1437  1431 root     S     1548   1%   0% clog -l ERROR
 1392  1386 root     S     1548   1%   0% clog -l ERROR
 2042   684 nobody   S     1444   1%   0% dnsmasq -i * -a 0.0.0.0 --keep-in-foreground -u nobody --cache=2048 -H /etc/dnrd/master --stop-dns-rebind --rebind-localhost-ok --conf-file=/tmp/dnsmasq.1_domains.conf --bind-loopback
 2086  2081 root     R        8   0%   0% [which]
  217     2 root     SW       0   0%   0% [mtdblockd]
    5     2 root     SW       0   0%   0% [events/0]
 1device wlan2 entered promiscuous mode
790     2 root     DW       0   0%   0% [mtlk]
    6     2 root     SW       0   0%   0% [khelper]
  242     2 root     SW       0   0%   0% [ubi_bgt0d]
  118     2 root     SW       0   0%   0% [kblockd/0]
  157     2 root     SW       0   0%   0% [aio/0]
  158     2 root     SW       0   0%   0% [crypto/0]
  156     2 root     SW       0   0%   0% [kswapd0]
 1425     2 root     SW       0   0%   0% [ifxhcd_workqueu]
  165     2 root     SW       0   0%   0% [crypto]
  166     2 root     SW       0   0%   0% [crypto_ret]
 1385     2 root     SW       0   0%   0% [ifxhcd_killurbd]
  116     2 root     SW       0   0%   0% [bdi-default]
 1285     2 root     SW       0   0%   0% [ipolldevd]
  127     2 root     SW       0   0%   0% [khubd]
  114     2 root     SW       0   0%   0% [sync_supers]
 1812     2 root     DW       0   0%   0% [mtlk]
 1823     2 root     DW       0   0%   0% [mtlk]
 1834     2 root     RW       0   0%   0% [mtlk]
 1384     2 root     SW       0   0%   0% [ifxhcd_workqueu]
    3     2 root     SW       0   0%   0% [ksoftirqd/0]
    4     2 root     SW       0   0%   0% [watchdog/0]
 1430     2 root     SW       0   0%   0% [ifxhcd_killurbd]
    2     0 root     SW       0   0%   0% [kthreadd]
    9     2 root     SW       0   0%   0% [async/mgr]

Configuration fil ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 
OL vap_stop +
wmi_unified_vdev_stop_send 
OL vap_stop -
STOPPED EVENT for vap 0 
e: /tmp/hostapd-wlan2.conf
 DEVICE IS DOWN ifname=wlan2
 DEVICE IS DOWN ifname=wlan2
Using interface wlan2 with hwaddr 00:02:61:ba:50:85 and ssid "Tilgin-ZgAzu9nyYsAF_5GHz"
 
 DES SSID SET=Tilgin-ZgAzu9nyYsAF_5GHz 
WPS: ConvOL vap_stop +
wmi_unified_vdev_stop_send 
OL vap_stop -
STOPPED EVENT for vap 0 
erting push_button to virtual_push_button for WPS 2.0 compliance
FWLOG: [44300] WAL_DBGID_SECURITY_ENCR_EN (  )
FWLOG: [44300] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )
OL vap_start +
OL vap_start -
ol_vdev_start_resp_ev
ol_ath_vap_join: join operation is only for STA/IBSS mode
ol_ath_wmm_update:
Notification to UMAC VAP layer
FWLOG: [44440] WHAL_ERROR_RESET_CHANNF1 (  )
Tunnel link is UP
wmi_unified_vdev_stop_send 
STOPPED EVENT for vap 0 
OL vap_start +
OL vap_start -
ol_vdev_start_resp_ev
ol_ath_vap_join: join operation is only for STA/IBSS mode
Notification to UMAC VAP layer
wmi_unified_vdev_stop_send 
STOPPED EVENT for vap 0 
FWLOG: [46128] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )
OL vap_stop +
wmi_unified_vdev_stop_send 
OL vap_stop -
STOPPED EVENT for vap 0 
Configuration file: /tmp/hostapd-wlan2.conf
OL vap_start +
OL vap_start -
ol_vdev_start_resp_ev
ol_ath_vap_join: join operation is only for STA/IBSS mode
ol_ath_wmm_update:
Notification to UMAC VAP layer
 ieee80211_ioctl_siwmode: imr.ifm_active=643, new mode=3, valid=1 
wmi_unified_vdev_stop_send 
STOPPED EVENT for vap 0 
 DEVICE IS DOWN ifname=wlan2
 DEVICE IS DOWN ifname=wlan2
Using interface wlan2 with hwaddr 00:02:61:ba:50:85 and ssid "Tilgin-ZgAzu9nyYsAF_5GHz"
CRM state '/voip/call/table' flags=0 saving...
CRM state '/voip/call/table' flags=0 saving... done. Status=EOK Count=0
CRM state '/' flags=0 saving...
WPS: Converting push_button to virtual_push_button for WPS 2.0 compliance
OL vap_stop +
wmi_unified_vdev_stop_send 
OL vap_stop -
STOPPED EVENT for vap 0 
OL vap_start +
OL vap_start -
ol_vdev_start_resp_ev
ol_ath_vap_join: join operation is only for STA/IBSS mode
ol_ath_wmm_update:
Notification to UMAC VAP layer
CRM state '/' flags=0 saving... done. Status=EOK Count=1185
find: /sys/class/scsi_disk/*/uevent: No such file or directory
FWLOG: [47481] WAL_DBGID_SECURITY_ENCR_EN (  )
FWLOG: [47481] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )
find: /sys/class/tty/tty????/uevent: No such file or directory
find: /sys/class/tty/wwan?/uevent: No such file or directory
find: /sys/class/usb/lp*/device/uevent: No such file or directory
1970-01-01 00:00:51: (/space/sources/02_07/factory/src/vood/ng/02_07/lighttpd/src/log.c.164) server started 
wmi_unified_vdev_stop_send 
STOPPED EVENT for vap 0 
OL vap_stop +
wmi_unified_vdev_stop_send 
OL vap_stop -
STOPPED EVENT for vap 0 
Tx power value is greater than supported max tx power 63, Limiting to default Max
Getting VHT MCS MAP set: 0
Configuration file: /tmp/hostapd-wlan0.conf
Using interface wlan0 with hwaddr 00:02:61:ba:50:82 and ssid "Tilgin-ZgAzu9nyYsAF"
udhcpd (v1.21.1) started
WPS: Converting push_button to virtual_push_button fo[4294721036] mtlk0(_mtlk_core_mbss_is_rescan_exempted:2758): Re-Scan cannot be exempted (20/40 is active)
[4294721046] mtlk0(mtlk_mbss_init:3439): CID-0000: _mtlk_core_mbss_check_activation_params returned successfully
[4294721056] mtlk0(_mtlk_mbss_preactivate:2917): CID-0000: Pre-activation configured parameters:
[4294721066] mtlk0(mtlk_core_configuration_dump:4938): CID-0000: Country             : SE
[4294721076] mtlk0(mtlk_core_configuration_dump:4939): CID-0000: Domain              : 48
[4294721086] mtlk0(mtlk_core_configuration_dump:4940): CID-0000: Network mode        : 802.11bgn
[4294721086] mtlk0(mtlk_core_configuration_dump:4941): CID-0000: Band                : 2.4
[4294721096] mtlk0(mtlk_core_configuration_dump:4942): CID-0000: Prog Model Spectrum : 40 MHz
[4294721106] mtlk0(mtlk_core_configuration_dump:4943): CID-0000: Selected Spectrum   : 40 MHz
[4294721116] mtlk0(mtlk_core_configuration_dump:4944): CID-0000: User Sel. Spectrum  : 40 MHz
[4294721126] mtlk0(mtlk_core_configuration_dump:4945): CID-0000: Bonding             : lower
[4294721126] mtlk0(mtlk_core_configuration_dump:4946): CID-0000: HT mode             : enabled
[4294721136] mtlk0(mtlk_core_configuration_dump:4948): CID-0000: SM enabled          : enabled
[4294721146] mtlk0(mtlk_aocs_set_config_frequency_band:3162): Overriding AOCS type for 2.4 GHz (NONE)
[4294721156] mtlk0(_mtlk_mbss_preactivate:2932): CID-0000: Start AOCS
[4294721166] mtlk0(_mtlk_mbss_preactivate:2945): CID-0000: ap_scan_band_cfg = 1
[4294721166] mtlk0(_mtlk_core_perform_initial_scan:2701): CID-0000: Scan started 40MHz
[4294721176] mtlk0(do_scan:596): Starting normal scan...
mtlk mtlk.0: firmware: requesting ProgModel_BG_CB_ar10.bin
r WPS 2.0 compliance
mtlk mtlk.0: firmware: requesting ProgModel_BG_CB_40_RevI_ar10.bin
[4294721666] mtlk0(prepare_progmodel_string:2061): CID-0000: ProgModel: ProgModel_BG_CB_40_RevI_ar10.bin version 2025

[4294723606] mtlk0(_mtlk_core_perform_initial_scan:2701): CID-0000: Scan started 20MHz
[4294723606] mtlk0(do_scan:596): Starting normal scan...
mtlk mtlk.0: firmware: requesting ProgModel_BG_nCB_ar10.bin
mtlk mtlk.0: firmware: requesting ProgModel_BG_nCB_40_RevI_ar10.bin
[4294723816] mtlk0(prepare_progmodel_string:2061): CID-0000: ProgModel: ProgModel_BG_nCB_40_RevI_ar10.bin version 2025

OL vap_start +
OL vap_start -
ol_vdev_start_resp_ev
ol_ath_vap_join: join operation is only for STA/IBSS mode
ol_ath_wmm_update:
ol_if_dfs_configure: called
ol_if_dfs_configure: ETSI domain
ol_if_dfs_disable: called
ol_if_dfs_enable: called
cac_start chan 5500 timeout 2 sec, curr time: 4294726 sec
Notification to UMAC VAP layer
[4294726736] mtlk<3>(_aocs_is_non_wifi_noise:3612): Force to 20 MHz mode due to interferer detection: RSSI:-43 thrsh:-60
[4294726736] mtlk<4>(aocs_detect_non_wifi_noise:3638): Coexistance switching to 20MHz Mode
[4294726746] mtlk0(_mtlk_core_aocs_on_spectrum_change:2879): CID-0000: Spectrum changed to 20MHz
[4294726756] mtlk0(_mtlk_mbss_preactivate:3040): CID-0000: Pre-activation selected parameters:
[4294726766] mtlk0(mtlk_core_configuration_dump:4938): CID-0000: Country             : SE
[4294726776] mtlk0(mtlk_core_configuration_dump:4939): CID-0000: Domain              : 48
[4294726786] mtlk0(mtlk_core_configuration_dump:4940): CID-0000: Network mode        : 802.11bgn
[4294726786] mtlk0(mtlk_core_configuration_dump:4941): CID-0000: Band                : 2.4
[4294726796] mtlk0(mtlk_core_configuration_dump:4942): CID-0000: Prog Model Spectrum : 20 MHz
[4294726806] mtlk0(mtlk_core_configuration_dump:4943): CID-0000: Selected Spectrum   : 20 MHz
[4294726816] mtlk0(mtlk_core_configuration_dump:4944): CID-0000: User Sel. Spectrum  : 40 MHz
[4294726826] mtlk0(mtlk_core_configuration_dump:4945): CID-0000: Bonding             : lower
[4294726826] mtlk0(mtlk_core_configuration_dump:4946): CID-0000: HT mode             : enabled
[4294726836] mtlk0(mtlk_core_configuration_dump:4948): CID-0000: SM enabled          : enabled
[4294726846] mtlk0(_mtlk_channels_frequency_element_dump:3086): CID-0000: Channel        : 1
[4294726856] mtlk0(_mtlk_channels_frequency_element_dump:3087): CID-0000: ChannelACT     : 0
[4294726866] mtlk0(_mtlk_channels_frequency_element_dump:3088): CID-0000: ScanType       : 0
[4294726876] mtlk0(_mtlk_channels_frequency_element_dump:3089): CID-0000: ChannelSwCnt   : 0
[4294726886] mtlk0(_mtlk_channels_frequency_element_dump:3090): CID-0000: SwitchMode     : 0
[4294726886] mtlk0(_mtlk_channels_frequency_element_dump:3091): CID-0000: SmRequired     : 0
[4294726896] mtlk0(_mtlk_channels_frequency_element_dump:3092): CID-0000: CbTxPowerLim   : 116
[4294726906] mtlk0(_mtlk_channels_frequency_element_dump:3093): CID-0000: nCbTxPowerLim  : 116
[4294726916] mtlk0(_mtlk_channels_frequency_element_dump:3094): CID-0000: AntennaGain    : 0
[4294726926] mtlk0(_mtlk_channels_frequency_element_dump:3095): CID-0000: ChannelLoad    : 0
[4294726936] mtlk0(_mtlk_channels_frequency_element_dump:3097): CID-0000: MaxTxPwr[0]    : 0
[4294726936] mtlk0(_mtlk_channels_frequency_element_dump:3098): CID-0000: MaxTxPwrIdx[0] : 0
[4294726946] mtlk0(_mtlk_channels_frequency_element_dump:3097): CID-0000: MaxTxPwr[1]    : 0
[4294726956] mtlk0(_mtlk_channels_frequency_element_dump:3098): CID-0000: MaxTxPwrIdx[1] : 0
[4294726966] mtlk0(_mtlk_channels_frequency_element_dump:3097): CID-0000: MaxTxPwr[2]    : 0
[4294726976] mtlk0(_mtlk_channels_frequency_element_dump:3098): CID-0000: MaxTxPwrIdx[2] : 0
[4294726976] mtlk0(_mtlk_channels_frequency_element_dump:3100): CID-0000: SwitchType     : 0
[4294726986] mtlk0(_mtlk_mbss_send_preactivate_req:2829): CID-0000: Sending UMI FW Preactivation
[4294727066] mtlk<3>(mtlk_core_set_force_ncb:6653): CID-0000: Error returned for UMI_FORCE_NCB request to MAC (err=2)
[4294727076] mtlk0(_mtlk_mbss_preactivate:3070): CID-0000: _mtlk_mbss_preactivate returned successfully
[4294727086] mtlk0(mtlk_mbss_init:3446): CID-0000: _mtlk_mbss_preactivate_if_needed returned successfully
[4294727086] mtlk0(mtlk_mbss_send_vap_activate:3134): CID-0000: Entering mtlk_mbss_send_vap_activate
[4294727096] mtlk0(mtlk_mbss_send_vap_activate:3141): CID-0000: Start activation
[4294727106] mtlk0(__mtlk_dump:66): dump of UMI_ACTIVATE_VAP:
cp= 0x86220700 l=152
0000:  00 02 61 ba 50 82 00 00  02 00 00 05 00 0f 00 00 
0010:  aa 0f 00 00 55 00 00 00  ff ff ff ff 13 00 00 00 
0020:  54 69 6c 67 69 6e 2d 5a  67 41 7a 75 39 6e 79 59 
0030:  73 41 46 00 00 00 00 00  00 00 00 00 00 00 00 00 
0040:  00 00 00 00 30 18 01 00  00 0f ac 02 02 00 00 0f 
0050:  ac 04 00 0f ac 02 01 00  00 0f ac 02 00 00 00 00 
0060:  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00 
0070:  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00 
0080:  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00 
0090:  00 00 00 00 09 00 00 00  
[4294727166] mtlk0(mtlk_mbss_send_vap_activate:3203): CID-0000: UMI_ACTIVATE_VAP
[4294727166] mtlk0(mtlk_mbss_send_vap_activate:3204): CID-0000: 	sBSSID = 00:02:61:BA:50:82
[4294727176] mtlk0(mtlk_mbss_send_vap_activate:3205): CID-0000: 	sSSID = Tilgin-ZgAzu9nyYsAF
[4294727186] mtlk0(mtlk_mbss_send_vap_activate:3206): CID-0000: 	Hidden = 0
[4294727196] mtlk0(__mtlk_dump:66): 	sRSNie = 
cp= 0x86220744 l=80
0000:  30 18 01 00 00 0f ac 02  02 00 00 0f ac 04 00 0f 
0010:  ac 02 01 00 00 0f ac 02  00 00 00 00 00 00 00 00 
0020:  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00 
0030:  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00 
0040:  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00 
[4294727226] mtlk0(mtlk_mbss_send_vap_activate:3210): CID-0000: mtlk_txmm_msg_send, MsgId = 0x453, ESSID = Tilgin-ZgAzu9nyYsAF
[4294727246] mtlk0(mtlk_mbss_init:3453): CID-0000: mtlk_mbss_send_vap_activate returned successfully
wmi_unified_vdev_stop_send 
STOPPED EVENT for vap 0 
OL vap_start +
OL vap_start -
ol_vdev_start_resp_ev
ol_ath_vap_join: join operation is only for STA/IBSS mode
ol_if_dfs_configure: called
ol_if_dfs_configure: ETSI domain
ol_if_dfs_disable: called
ol_if_dfs_enable: called
cac_start chan 5500 timeout 2 sec, curr time: 4294727 sec
Notification to UMAC VAP layer
cac_timeout cac expired, chan 5500 curr time 4294729
TAPI, Version 4.10.4.2, (c) 2001-2013 Lantiq Deutschland GmbH
Lantiq MIPS34KEc MPS driver, version 2.2.7.0, (c) 2006-2010 Lantiq Deutschland GmbH
Lantiq VMMC device driver, version 1.15.0.4, (c) 2006-2013 Lantiq Deutschland GmbH
bkos: hal received command 2
CRM is considered alive and well - removing threat limit