Getting openwrt installed on Etisalat Sercomm S3
Hardware Specs
Snapshot firmware links
etisalat_s3-squashfs-factory.img
etisalat_s3-squashfs-sysupgrade.bin
2 Likes
There's no installation instructions.
Working on that
Just booted initramfs
Bytes transferred = 5617525 (55b775 hex)
LoadAddr=88000000 NetBootFileXferSize= 0055b775
MT7621 # bootm
## Booting image at 88000000 ...
Image Name: MIPS OpenWrt Linux-5.10.162
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 5617461 Bytes = 5.4 MB
Load Address: 81001000
Entry Point: 81001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
hdr->ih_os is 5
do_bootm:
cmdtp : 8ffb0624
flag : 0
argc : 1
argv[0] : bootm
addr : 88000000
len_ptr : 88000040
verify : 1
No initrd
## Transferring control to Linux (at address 81001000) ...
## Giving linux memsize in MB, 256
Starting kernel ...
OpenWrt kernel loader for MIPS based SoC
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Decompressing kernel... done!
Starting kernel at 80001000...
[ 0.000000] Linux version 5.10.162 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r21714-9ac377d0e0) 11.3.0, GNU ld (GNU Binutils) 2.39) #0 SMP Sat Jan 7 00:32:58 2023
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Etisalat S3
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] percpu: Embedded 15 pages/cpu s30480 r8192 d22768 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Writing ErrCtl register=00053ed8
[ 0.000000] Readback ErrCtl register=00053ed8
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 246092K/262144K available (7058K kernel code, 632K rwdata, 1420K rodata, 3868K init, 243K bss, 16052K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000012] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.015863] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.033809] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.106116] pid_max: default: 32768 minimum: 301
[ 0.115429] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.129833] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.148018] rcu: Hierarchical SRCU implementation.
[ 0.157815] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.173369] smp: Bringing up secondary CPUs ...
[ 0.183077] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.183086] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.183097] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.183170] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.243176] Synchronize counters for CPU 1: done.
[ 0.304853] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.304862] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.304871] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.304916] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.364028] Synchronize counters for CPU 2: done.
[ 0.424376] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.424384] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.424393] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.424441] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.483603] Synchronize counters for CPU 3: done.
[ 0.543212] smp: Brought up 1 node, 4 CPUs
[ 0.555745] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.575258] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.589071] pinctrl core: initialized pinctrl subsystem
[ 0.601762] NET: Registered protocol family 16
[ 0.611648] thermal_sys: Registered thermal governor 'step_wise'
[ 0.612866] cpuidle: using governor teo
[ 0.677799] clocksource: Switched to clocksource GIC
[ 0.689538] NET: Registered protocol family 2
[ 0.698580] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.714582] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.731226] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.746348] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.760527] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.773262] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.786146] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.800258] NET: Registered protocol family 1
[ 0.808819] PCI: CLS 0 bytes, default 32
[ 4.311400] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 4.328264] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 4.339749] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 4.360121] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 4.376562] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 4.387959] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 4.399314] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 4.411206] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 4.427946] printk: console [ttyS0] disabled
[ 4.436402] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 4.454346] printk: console [ttyS0] enabled
[ 4.454346] printk: console [ttyS0] enabled
[ 4.470882] printk: bootconsole [early0] disabled
[ 4.470882] printk: bootconsole [early0] disabled
[ 4.490433] 1e000e00.uartlite3: ttyS1 at MMIO 0x1e000e00 (irq = 20, base_baud = 3125000) is a 16550A
[ 4.512033] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
[ 4.524717] nand: Macronix MX30LF1G18AC
[ 4.532358] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 4.547434] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
[ 4.617777] scpart: Valid 'SC PART MAP' (10 partitions) found at 0x100000
[ 4.631362] 10 scpart partitions found on MTD device mt7621-nand
[ 4.644628] Creating 10 MTD partitions on "mt7621-nand":
[ 4.655246] 0x000000000000-0x000000100000 : "u-boot"
[ 4.676194] 0x000000100000-0x000000200000 : "dynamic partition map"
[ 4.699764] 0x000000200000-0x000000300000 : "Factory"
[ 4.721015] 0x000000300000-0x000000400000 : "Boot Flag"
[ 4.742461] 0x000000400000-0x000000a00000 : "kernel"
[ 4.813663] 0x000000a00000-0x000001000000 : "Kernel 2"
[ 4.885257] 0x000001000000-0x000003000000 : "File System 1"
[ 5.219249] 0x000003000000-0x000005020000 : "File System 2"
[ 5.553838] 0x000005020000-0x000006420000 : "Configuration/log"
[ 5.767880] 0x000006420000-0x000007f80000 : "application tmp buffer (Ftool)"
[ 6.064233] Concatenating MTD devices:
[ 6.071763] (0): "File System 1"
[ 6.078229] (1): "Configuration/log"
[ 6.085329] (2): "application tmp buffer (Ftool)"
[ 6.094686] into device "ubi-concat"
[ 6.101850] 1 fixed-partitions partitions found on MTD device ubi-concat
[ 6.115191] Creating 1 MTD partitions on "ubi-concat":
[ 6.125426] 0x000000000000-0x000004f80000 : "ubi"
[ 6.134790] mtd: partition "ubi" extends beyond the end of device "ubi-concat" -- size truncated to 0x4f60000
[ 6.999153] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 7.026748] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 22
[ 7.044413] mtk_soc_eth 1e100000.ethernet wan: mediatek frame engine at 0xbe100000, irq 22
[ 7.062346] i2c /dev entries driver
[ 7.072090] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 7.085492] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 7.103025] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000
[ 7.119321] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 7.135700] mt7621-pci 1e140000.pcie: Parsing DT failed
[ 7.148588] NET: Registered protocol family 10
[ 7.159407] Segment Routing with IPv6
[ 7.166795] NET: Registered protocol family 17
[ 7.175769] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 7.202022] 8021q: 802.1Q VLAN Support v1.8
[ 7.213873] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 7.301259] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=27)
[ 7.323296] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=28)
[ 7.345306] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=29)
[ 7.367321] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7530 PHY] (irq=30)
[ 7.389711] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[ 7.406546] DSA: tree 0 setup
[ 7.412787] rt2880-pinmux pinctrl: pcie is already enabled
[ 7.423813] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 7.437180] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 7.454721] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000
[ 7.471024] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 7.487401] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[ 7.502494] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[ 7.517493] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22
[ 7.632094] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[ 7.643209] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[ 7.754476] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 7.768347] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 7.778061] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 7.787781] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 7.806481] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 7.819182] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 7.832891] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 7.846588] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 7.857521] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff])
[ 7.877849] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 7.889831] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 7.902317] pci 0000:00:00.0: reg 0x14: initial BAR value 0x00000000 invalid
[ 7.916355] pci 0000:00:00.0: reg 0x14: [mem size 0x00010000]
[ 7.927870] pci 0000:00:00.0: supports D1
[ 7.935838] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 7.947974] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 7.960015] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 7.972514] pci 0000:00:01.0: reg 0x14: initial BAR value 0x00000000 invalid
[ 7.986553] pci 0000:00:01.0: reg 0x14: [mem size 0x00010000]
[ 7.998082] pci 0000:00:01.0: supports D1
[ 8.006049] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 8.019248] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 8.035233] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 8.051419] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280
[ 8.063455] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[ 8.077502] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000 64bit]
[ 8.090160] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 8.121449] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 8.131904] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 8.144044] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 8.157570] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff pref]
[ 8.171965] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 8.185424] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
[ 8.197438] pci 0000:02:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[ 8.211487] pci 0000:02:00.0: reg 0x10: [mem size 0x00100000]
[ 8.223080] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 8.236918] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 8.247381] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 8.259526] pci 0000:00:01.0: bridge window [mem 0x60000000-0x600fffff]
[ 8.273048] pci 0000:00:01.0: bridge window [mem 0x60000000-0x600fffff pref]
[ 8.287437] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 8.300676] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 8.313852] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 8.327742] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 8.340922] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 8.354792] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 8.368329] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[ 8.382718] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[ 8.396242] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref]
[ 8.410634] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff]
[ 8.424163] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff]
[ 8.437696] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff]
[ 8.451224] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff]
[ 8.464756] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[ 8.479329] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 8.489229] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff]
[ 8.502751] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 8.516272] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 8.530670] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff]
[ 8.544194] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 8.554093] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff]
[ 8.567614] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 8.581139] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref]
[ 8.599248] UBI error: no valid UBI magic found inside mtd10
[ 8.611439] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 8.639567] Freeing unused kernel memory: 3868K
[ 8.648629] This architecture does not have kernel memory protection.
[ 8.661467] Run /init as init process
[ 9.034650] init: Console is alive
[ 9.041859] init: - watchdog -
[ 9.059469] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 9.080760] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 9.108195] init: - preinit -
[ 9.328332] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.416011] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.467244] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.784365] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 9.800680] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 9.808377] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 9.831012] 8021q: adding VLAN 0 to HW filter on device lan1
[ 9.844923] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 11.995999] procd: - early -
[ 12.002046] procd: - watchdog -
[ 12.587951] procd: - watchdog -
[ 12.594630] procd: - ubus -
[ 12.607395] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.658544] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.671765] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.688252] procd: - init -
Please press Enter to activate this console.
[ 13.043008] kmodloader: loading kernel modules from /etc/modules.d/*
[ 13.113447] PPP generic driver version 2.4.2
[ 13.123790] NET: Registered protocol family 24
[ 13.140376] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 13.261775] urngd: v1.0.2 started.
[ 13.437670] random: crng init done
[ 13.444490] random: 31 urandom warning(s) missed due to ratelimiting
BusyBox v1.35.0 (2023-01-07 00:32:58 UTC) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r21714-9ac377d0e0
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/#
root@OpenWrt:/# cat /proc/mtd
dev: size erasesize name
mtd0: 00100000 00020000 "u-boot"
mtd1: 00100000 00020000 "dynamic partition map"
mtd2: 00100000 00020000 "Factory"
mtd3: 00100000 00020000 "Boot Flag"
mtd4: 00600000 00020000 "kernel"
mtd5: 00600000 00020000 "Kernel 2"
mtd6: 02000000 00020000 "File System 1"
mtd7: 02020000 00020000 "File System 2"
mtd8: 01400000 00020000 "Configuration/log"
mtd9: 01b60000 00020000 "application tmp buffer (Ftool)"
mtd10: 04f60000 00020000 "ubi"
1 Like
Update squashfs-factory image via web
after installing Snapshot image there will be no web interface unless you install it via shell.
opkg update && opkg install luci
1 Like
The installation guide was in the git commit. And I've added it to the wiki:
Feel free to improve: add photos, bootlogs etc.
5 Likes
Currently USB port is not working
[ 15.808434] kmodloader: 6 modules could not be probed
[ 15.819796] kmodloader: - usb-common - 0
[ 15.828368] kmodloader: dependency not loaded usb-common
[ 15.839714] kmodloader: - usbcore - 1
[ 15.847643] kmodloader: dependency not loaded usb-common
[ 15.858850] kmodloader: dependency not loaded usbcore
[ 15.869566] kmodloader: - xhci-hcd - 2
[ 15.877659] kmodloader: dependency not loaded xhci-hcd
[ 15.888509] kmodloader: dependency not loaded usbcore
[ 15.898940] kmodloader: - xhci-mtk - 2
[ 15.906690] kmodloader: dependency not loaded usbcore
[ 15.917134] kmodloader: dependency not loaded xhci-hcd
[ 15.927840] kmodloader: - xhci-pci - 2
[ 15.935642] kmodloader: dependency not loaded usbcore
[ 15.946076] kmodloader: dependency not loaded xhci-hcd
[ 15.957056] kmodloader: dependency not loaded usb-common
[ 15.968683] kmodloader: - xhci-plat-hcd - 3
Which image are you using?
What's wrong with my my installations?
I got a few of these routers & usb port is not working in any of them.
i am using these images
https://downloads.openwrt.org/snapshots/targets/ramips/mt7621/openwrt-ramips-mt7621-etisalat_s3-squashfs-factory.img
https://downloads.openwrt.org/snapshots/targets/ramips/mt7621/openwrt-ramips-mt7621-etisalat_s3-squashfs-sysupgrade.bin
Found some info
Login info of the built-in shell
User: SuperUser
Password: SN (Printed on back of your router)
Once loged in type sh press enter for shell access
my usb port was not working as i did not follow the installation guide here
Now my understanding is openwrt must be installed & boot from slot 0 in the flash
& bootflag should be "Boot Flag : Sercomm0" in bootlog
everything works fine now
1 Like
You're right, OpenWrt must be installed on Slot 0 & boot from Slot 0. It means that we need to flash OpenWrt factory.img from the Slot 1 of stock firmware. Otherwise, we can even get a brick (bootloop) and only sercomm-recovery utility can help us. If you have bricked routers and mtd backup of the any Etisalat S3 router then I can try to make the recovery image for sercomm-recovery.
All this long installation guide is needed only in order to switch the stock firmware to Slot 1 (Boot Flag : Sercomm1).
You can also try community release builds of the OpenWrt (including 22.03.3) - https://mega.nz/folder/xoBklZTZ#g1l_wH-nBOMONrDqOkeEvQ
1 Like
This is probably JTAG interface.
If yes, how can i find pinouts.
I have a bricked router which i want to recover with JTAG.
Greetings, I upgraded the stock firmware, however it works boot with openwrt one time afterwards it not booting. I am pasting bootlog here, can anyone here help me to resolve the issue..
===================================================================
MT7621 stage1 code 10:33:11 (ASIC)
CPU=50000000 HZ BUS=16666666 HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x11100000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-1200Mhz ===
PLL3 FB_DL: 0x2, 1/0 = 675/349 09000000
PLL2 FB_DL: 0x12, 1/0 = 712/312 49000000
PLL4 FB_DL: 0x16, 1/0 = 729/295 59000000
do DDR setting..[00320381]
Apply DDR3 Setting...(use customer AC)
0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120
--------------------------------------------------------------------------------
0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000E:| 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1
000F:| 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1
0010:| 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0
0011:| 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0
0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
rank 0 coarse = 16
rank 0 fine = 40
B:| 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 0
opt_dle value:8
DRAMC_R0DELDLY[018]=00002121
==================================================================
RX DQS perbit delay software calibration
==================================================================
1.0-15 bit dq delay value
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 11 7 10 10 10 6 11 5 3 8
10 | 6 10 6 8 4 7
--------------------------------------
==================================================================
2.dqs window
x=pass dqs delay value (min~max)center
y=0-7bit DQ of every group
input delay:DQS0 =33 DQS1 = 33
==================================================================
bit DQS0 bit DQS1
0 (1~65)33 8 (1~61)31
1 (1~59)30 9 (1~62)31
2 (0~62)31 10 (2~64)33
3 (1~64)32 11 (1~61)31
4 (1~65)33 12 (1~65)33
5 (0~63)31 13 (1~60)30
6 (1~62)31 14 (1~62)31
7 (1~61)31 15 (1~62)31
==================================================================
3.dq delay value last
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 11 10 12 11 10 8 13 7 5 10
10 | 6 12 6 11 6 9
==================================================================
==================================================================
TX perbyte calibration
==================================================================
DQS loop = 15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1
dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2
DQ loop=15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=15, finish count=1
dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=2
byte:0, (DQS,DQ)=(8,8)
byte:1, (DQS,DQ)=(8,8)
20,data:88
[EMI] DRAMC calibration passed
===================================================================
MT7621 stage1 code done
CPU=50000000 HZ BUS=16666666 HZ
===================================================================
U-Boot 1.1.3 (Mar 4 2020 - 17:12:16)
Board: Ralink APSoC DRAM: 256 MB
rt2880 uboot v0.00e04 05/25/2006
SERIAL_CLOCK_DIVISOR =16
kaiker,,CONFIG_BAUDRATE =57600
SDRAM SIZE:10000000
Top of RAM usable for U-Boot at: 90000000
Reserving 425k for U-Boot at: 8ff94000
Reserving 1028k for malloc() at: 8fe93000
Reserving 44 Bytes for Board Info at: 8fe92fd4
Reserving 36 Bytes for Global Data at: 8fe92fb0
Reserving 128k for boot params() at: 8fe72fb0
Stack Pointer at: 8fe72f98
relocate_code Pointer at: 8ff94000
Config XHCI 40M PLL
******************************
Software System Reset Occurred
******************************
Now running in RAM - U-Boot at: 8ff94000
monitor_flash_len =116812
Command "mdio": 0xa0206984 => 0x8ff9a984
Command "nand": 0xa020c2bc => 0x8ffa02bc
Command "reset": 0xa0215cec => 0x8ffa9cec
Command "go": 0xa020dc68 => 0x8ffa1c68
Command "bootm": 0xa020e4c4 => 0x8ffa24c4
Command "loadb": 0xa020f184 => 0x8ffa3184
Command "tftpboot": 0xa020f7b4 => 0x8ffa37b4
Command "nm": 0xa020fe40 => 0x8ffa3e40
Command "mm": 0xa020fea4 => 0x8ffa3ea4
Command "md": 0xa020ff08 => 0x8ffa3f08
Command "saveenv": 0xa0210480 => 0x8ffa4480
Command "setenv": 0xa0210df0 => 0x8ffa4df0
Command "printenv": 0xa02104d0 => 0x8ffa44d0
Command "?": 0xa02110c4 => 0x8ffa50c4
Command "help": 0xa02110c4 => 0x8ffa50c4
Command "version": 0xa0210f84 => 0x8ffa4f84
Command "sc_boot": 0xa0213d30 => 0x8ffa7d30
Command "sc_nand": 0xa0213d68 => 0x8ffa7d68
Command "sc_eth_test": 0xa0213da4 => 0x8ffa7da4
Command "sc_phy": 0xa0213de0 => 0x8ffa7de0
Command "sc_time": 0xa0213e1c => 0x8ffa7e1c
Command "sc_btver": 0xa0213e54 => 0x8ffa7e54
Command "sc_fl_map": 0xa0213e90 => 0x8ffa7e90
Command "sc_endian": 0xa0213ecc => 0x8ffa7ecc
Command "sc_gpio": 0xa0213f08 => 0x8ffa7f08
Command "sc_led": 0xa0213f44 => 0x8ffa7f44
Command "sc_dl": 0xa0213f80 => 0x8ffa7f80
Allocate 16 byte aligned buffer: 8ffca410
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [C2 F1 80 95 02]
Device found in MTK table, ID: c2f1, EXT_ID: 809502
Support this Device in MTK table! c2f1
select_chip
[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
Signature matched and data read!
load_fact_bbt success 1023
load fact bbt success
[mtk_nand] probe successfully!
mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8
*** Warning - bad CRC, using default environment
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =256 Mbytes
#Reset_MT7530
set LAN/WAN WLLLL
Load Standalone from 40000
SC_DEBUG: Nand Partition Table Magic Found at 100000.
******************************************
Uboot StandAlone Entry
******************************************
GPIO init
*********************************************************
Press any key to enter Boot Command Interface
********************************************************* 0
U-Boot 1.1.3 (Mar 4 2020 - 17:12:16)
MT7621 #
1 Like
Update it with TFTP
For TFTP to get working set your pc ip address 192.168.1.2
on serial cosole type these commands
setenv serverip 192.168.1.2
setenv ipaddr 192.168.1.1
saveenv
tftp 88000000 openwrtinitramfs.bin
bootm 88000000
then plug internet connection in wan port, install luci & update sysupgrade file, or put sysupgrade file in /tmp with SCP. & type in console
sysupgrade openwrtsysupgrade.bin
Still no Success
U-Boot 1.1.3 (Mar 4 2020 - 17:12:16)
Board: Ralink APSoC DRAM: 256 MB
rt2880 uboot v0.00e04 05/25/2006
SERIAL_CLOCK_DIVISOR =16
kaiker,,CONFIG_BAUDRATE =57600
SDRAM SIZE:10000000
Top of RAM usable for U-Boot at: 90000000
Reserving 425k for U-Boot at: 8ff94000
Reserving 1028k for malloc() at: 8fe93000
Reserving 44 Bytes for Board Info at: 8fe92fd4
Reserving 36 Bytes for Global Data at: 8fe92fb0
Reserving 128k for boot params() at: 8fe72fb0
Stack Pointer at: 8fe72f98
relocate_code Pointer at: 8ff94000
Config XHCI 40M PLL
******************************
Software System Reset Occurred
******************************
Now running in RAM - U-Boot at: 8ff94000
monitor_flash_len =116812
Command "mdio": 0xa0206984 => 0x8ff9a984
Command "nand": 0xa020c2bc => 0x8ffa02bc
Command "reset": 0xa0215cec => 0x8ffa9cec
Command "go": 0xa020dc68 => 0x8ffa1c68
Command "bootm": 0xa020e4c4 => 0x8ffa24c4
Command "loadb": 0xa020f184 => 0x8ffa3184
Command "tftpboot": 0xa020f7b4 => 0x8ffa37b4
Command "nm": 0xa020fe40 => 0x8ffa3e40
Command "mm": 0xa020fea4 => 0x8ffa3ea4
Command "md": 0xa020ff08 => 0x8ffa3f08
Command "saveenv": 0xa0210480 => 0x8ffa4480
Command "setenv": 0xa0210df0 => 0x8ffa4df0
Command "printenv": 0xa02104d0 => 0x8ffa44d0
Command "?": 0xa02110c4 => 0x8ffa50c4
Command "help": 0xa02110c4 => 0x8ffa50c4
Command "version": 0xa0210f84 => 0x8ffa4f84
Command "sc_boot": 0xa0213d30 => 0x8ffa7d30
Command "sc_nand": 0xa0213d68 => 0x8ffa7d68
Command "sc_eth_test": 0xa0213da4 => 0x8ffa7da4
Command "sc_phy": 0xa0213de0 => 0x8ffa7de0
Command "sc_time": 0xa0213e1c => 0x8ffa7e1c
Command "sc_btver": 0xa0213e54 => 0x8ffa7e54
Command "sc_fl_map": 0xa0213e90 => 0x8ffa7e90
Command "sc_endian": 0xa0213ecc => 0x8ffa7ecc
Command "sc_gpio": 0xa0213f08 => 0x8ffa7f08
Command "sc_led": 0xa0213f44 => 0x8ffa7f44
Command "sc_dl": 0xa0213f80 => 0x8ffa7f80
Allocate 16 byte aligned buffer: 8ffca410
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [C2 F1 80 95 02]
Device found in MTK table, ID: c2f1, EXT_ID: 809502
Support this Device in MTK table! c2f1
select_chip
[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
Signature matched and data read!
load_fact_bbt success 1023
load fact bbt success
[mtk_nand] probe successfully!
mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =256 Mbytes
#Reset_MT7530
set LAN/WAN WLLLL
Load Standalone from 40000
SC_DEBUG: Nand Partition Table Magic Found at 100000.
******************************************
Uboot StandAlone Entry
******************************************
GPIO init
*********************************************************
Press any key to enter Boot Command Interface
********************************************************* 0
U-Boot 1.1.3 (Mar 4 2020 - 17:12:16)
MT7621 # setenv serverip 192.168.1.2
MT7621 # setenv ipaddr 192.168.1.1
MT7621 # saveenv
Saving Environment to NAND Flash...
Erasing NAND Flash...
ranand_erase: start:80000, len:20000
.Writing to NAND Flash...
done
Unknown command 'openwrtinitra' - try 'help'
MT7621 # tftp 88000000 openwrtinitramfs.bin
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'openwrtinitramfs.bin'.
TIMEOUT_COUNT=10,Load address: 0x88000000
Loading: checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
Got ARP REPLY, set server/gtwy eth addr (28:f1:0e:03:f4:de)
Got it
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
####################################################Got ARP REQUEST, return our IP
#############
#################################################################
#################################################################
#################################################################
######
done
Bytes transferred = 7014973 (6b0a3d hex)
LoadAddr=88000000 NetBootFileXferSize= 006b0a3d
MT7621 # bootm 88000000
## Booting image at 88000000 ...
Bad Magic Number,73797375
MT7621 #
Use initramfs image
openwrt-ramips-mt7621-etisalat_s3-initramfs-kernel.bin
***************************************************
Boot Version 0.2.1.0, at Mar 4 2020, 17:12:13
***************************************************
SC_DEBUG: Nand Partition Table Magic Found at 100000.
Entering Firmware : Everything is OK.
*************************************
Boot Flag : Sercomm1▒
*************************************
Fw header Magic check OK!
FW header checksum should: 0x155cb0ba, crc32 result: 0x155cb0ba, Fw header CRC check OK!
kernel : real offset: 0x00a00100, data length: 0x002c4e1b,checksum :0xaac71265
kernel result: 0xaac71265, kernel check sum ok!
rootfs: real offset: 0x03000000, data length: 0x00000004, checksum :0x2d55fc1c
rootfs result: 0x2d55fc1c, rootfs check sum ok!
Kernel Addr : 0xbca00100
## Booting image at bca00100 ...
Image Name: MIPS OpenWrt Linux-5.10.162
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2903515 Bytes = 2.8 MB
Load Address: 81001000
Entry Point: 81001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
kernel addr :0xBCA00100
No initrd
## Transferring control to Linux (at address 81001000) ...
## Giving linux memsize in MB, 256
Starting kernel ...
OpenWrt kernel loader for MIPS based SoC
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Decompressing kernel... done!
Starting kernel at 80001000...
[ 0.000000] Linux version 5.10.162 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 12.2.0 r21791-c03e458c86) 12.2.0, GNU ld (GNU Binutils) 2.39) #0 SMP Fri Jan 13 21:34:16 2023
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Etisalat S3
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] percpu: Embedded 15 pages/cpu s30480 r8192 d22768 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Writing ErrCtl register=0000000f
[ 0.000000] Readback ErrCtl register=0000000f
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 248716K/262144K available (7025K kernel code, 629K rwdata, 1416K rodata, 1284K init, 243K bss, 13428K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000012] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.015860] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.033808] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.106131] pid_max: default: 32768 minimum: 301
[ 0.115441] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.129847] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.148110] rcu: Hierarchical SRCU implementation.
[ 0.157925] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.173520] smp: Bringing up secondary CPUs ...
[ 0.183257] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.183270] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.183282] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.183356] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.243331] Synchronize counters for CPU 1: done.
[ 0.305487] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.305497] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.305505] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.305550] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.364453] Synchronize counters for CPU 2: done.
[ 0.424816] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.424826] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.424833] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.424883] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.484035] Synchronize counters for CPU 3: done.
[ 0.543648] smp: Brought up 1 node, 4 CPUs
[ 0.555950] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.575456] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.589271] pinctrl core: initialized pinctrl subsystem
[ 0.601988] NET: Registered protocol family 16
[ 0.611871] thermal_sys: Registered thermal governor 'step_wise'
[ 0.613361] cpuidle: using governor teo
[ 0.640479] OF: /ethernet@1e100000/mac@0: could not get #nvmem-cell-cells for /nand@1e003000/partitions/partition@200000/macaddr@21000
[ 0.664500] OF: /ethernet@1e100000/mac@1: could not get #nvmem-cell-cells for /nand@1e003000/partitions/partition@200000/macaddr@21000
[ 0.689639] OF: /pcie@1e140000/pcie@0,0/wifi@0,0: could not get #nvmem-cell-cells for /nand@1e003000/partitions/partition@200000/macaddr@21000
[ 0.715059] OF: /pcie@1e140000/pcie@1,0/wifi@0,0: could not get #nvmem-cell-cells for /nand@1e003000/partitions/partition@200000/macaddr@21000
[ 0.740886] OF: /pcie@1e140000/pcie@0,0/wifi@0,0: could not get #nvmem-cell-cells for /nand@1e003000/partitions/partition@200000/macaddr@21000
[ 0.766296] OF: /pcie@1e140000/pcie@1,0/wifi@0,0: could not get #nvmem-cell-cells for /nand@1e003000/partitions/partition@200000/macaddr@21000
[ 0.792115] OF: /pcie@1e140000/pcie@0,0/wifi@0,0: could not get #nvmem-cell-cells for /nand@1e003000/partitions/partition@200000/macaddr@21000
[ 0.817541] OF: /pcie@1e140000/pcie@1,0/wifi@0,0: could not get #nvmem-cell-cells for /nand@1e003000/partitions/partition@200000/macaddr@21000
[ 0.875747] clocksource: Switched to clocksource GIC
[ 0.887406] NET: Registered protocol family 2
[ 0.896444] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.911799] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.928437] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.943632] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.957741] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.970499] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.983386] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.997517] NET: Registered protocol family 1
[ 1.006106] PCI: CLS 0 bytes, default 32
[ 1.016536] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 1.033236] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.044722] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 1.065300] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 1.081860] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.093157] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.104433] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.116085] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 1.132508] printk: console [ttyS0] disabled
[ 1.140997] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 1.158918] printk: console [ttyS0] enabled
[ 1.158918] printk: console [ttyS0] enabled
[ 1.175449] printk: bootconsole [early0] disabled
[ 1.175449] printk: bootconsole [early0] disabled
[ 1.195172] 1e000e00.uartlite3: ttyS1 at MMIO 0x1e000e00 (irq = 20, base_baud = 3125000) is a 16550A
[ 1.216877] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
[ 1.229608] nand: Macronix MX30LF1G18AC
[ 1.237261] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.252347] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
[ 1.322804] scpart: Valid 'SC PART MAP' (10 partitions) found at 0x100000
[ 1.336389] 10 scpart partitions found on MTD device mt7621-nand
[ 1.348749] Creating 10 MTD partitions on "mt7621-nand":
[ 1.359367] 0x000000000000-0x000000100000 : "u-boot"
[ 1.380593] 0x000000100000-0x000000200000 : "dynamic partition map"
[ 1.404306] 0x000000200000-0x000000300000 : "Factory"
[ 1.425567] 0x000000300000-0x000000400000 : "Boot Flag"
[ 1.447027] 0x000000400000-0x000000a00000 : "kernel"
[ 1.518234] 0x000000a00000-0x000001000000 : "Kernel 2"
[ 1.589949] 0x000001000000-0x000003000000 : "File System 1"
[ 1.923864] 0x000003000000-0x000005000000 : "File System 2"
[ 2.257911] 0x000005000000-0x000006400000 : "Configuration/log"
[ 2.472022] 0x000006400000-0x000007f80000 : "application tmp buffer (Ftool)"
[ 2.770691] Concatenating MTD devices:
[ 2.778240] (0): "File System 1"
[ 2.784662] (1): "Configuration/log"
[ 2.791786] (2): "application tmp buffer (Ftool)"
[ 2.801144] into device "ubi-concat"
[ 2.808310] 1 fixed-partitions partitions found on MTD device ubi-concat
[ 2.821654] Creating 1 MTD partitions on "ubi-concat":
[ 2.831891] 0x000000000000-0x000004f80000 : "ubi"
[ 3.687127] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 3.704599] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 22
[ 3.722277] mtk_soc_eth 1e100000.ethernet wan: mediatek frame engine at 0xbe100000, irq 22
[ 3.740029] i2c /dev entries driver
[ 3.749052] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 3.762452] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 3.780001] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000
[ 3.796305] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 3.812687] mt7621-pci 1e140000.pcie: Parsing DT failed
[ 3.825419] NET: Registered protocol family 10
[ 3.836258] Segment Routing with IPv6
[ 3.843644] NET: Registered protocol family 17
[ 3.852608] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 3.878840] 8021q: 802.1Q VLAN Support v1.8
[ 3.890656] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 3.919498] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=27)
[ 3.941505] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=28)
[ 3.963528] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=29)
[ 3.985532] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7530 PHY] (irq=30)
[ 4.007906] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[ 4.024731] DSA: tree 0 setup
[ 4.030959] rt2880-pinmux pinctrl: pcie is already enabled
[ 4.041985] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 4.055345] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 4.072880] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000
[ 4.089178] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 4.105556] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[ 4.120648] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[ 4.135656] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22
[ 4.250278] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[ 4.261390] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[ 4.372618] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 4.386485] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 4.396194] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 4.405910] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 4.424603] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 4.437288] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 4.450983] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 4.464676] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 4.475601] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff])
[ 4.495919] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 4.507894] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 4.520376] pci 0000:00:00.0: reg 0x14: [mem 0x60400000-0x6040ffff]
[ 4.532915] pci 0000:00:00.0: supports D1
[ 4.540898] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 4.552604] OF: /pcie@1e140000/pcie@0,0/wifi@0,0: could not get #nvmem-cell-cells for /nand@1e003000/partitions/partition@200000/macaddr@21000
[ 4.578281] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 4.590268] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 4.602751] pci 0000:00:01.0: reg 0x14: [mem 0x60410000-0x6041ffff]
[ 4.615287] pci 0000:00:01.0: supports D1
[ 4.623269] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 4.634974] OF: /pcie@1e140000/pcie@1,0/wifi@0,0: could not get #nvmem-cell-cells for /nand@1e003000/partitions/partition@200000/macaddr@21000
[ 4.661827] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280
[ 4.673843] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[ 4.687889] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000 64bit]
[ 4.700544] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 4.730403] OF: /pcie@1e140000/pcie@0,0/wifi@0,0: could not get #nvmem-cell-cells for /nand@1e003000/partitions/partition@200000/macaddr@21000
[ 4.757020] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 4.767438] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 4.779571] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 4.793097] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 4.807486] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 4.820919] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
[ 4.832921] pci 0000:02:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[ 4.846969] pci 0000:02:00.0: reg 0x10: [mem size 0x00100000]
[ 4.858546] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 4.870956] OF: /pcie@1e140000/pcie@1,0/wifi@0,0: could not get #nvmem-cell-cells for /nand@1e003000/partitions/partition@200000/macaddr@21000
[ 4.897568] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 4.907994] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 4.920128] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 4.933644] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref]
[ 4.948038] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 4.961255] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 4.974429] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 4.988296] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 5.001464] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 5.015328] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 5.028857] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[ 5.043239] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[ 5.056761] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref]
[ 5.071146] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff]
[ 5.084669] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff]
[ 5.098199] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff]
[ 5.111717] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff]
[ 5.125243] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[ 5.139810] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 5.149697] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff]
[ 5.163221] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 5.176741] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 5.191131] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff]
[ 5.204648] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 5.214534] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff]
[ 5.228060] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 5.241576] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref]
[ 5.259438] UBI error: no valid UBI magic found inside mtd10
[ 5.271502] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 5.286011] /dev/root: Can't open blockdev
[ 5.294184] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[ 5.309126] Please append a correct "root=" boot option; here are the available partitions:
[ 5.325773] 1f00 1024 mtdblock0
[ 5.325778] (driver?)
[ 5.338794] 1f01 1024 mtdblock1
[ 5.338798] (driver?)
[ 5.351805] 1f02 1024 mtdblock2
[ 5.351810] (driver?)
[ 5.364814] 1f03 1024 mtdblock3
[ 5.364819] (driver?)
[ 5.377847] 1f04 6144 mtdblock4
[ 5.377852] (driver?)
[ 5.390862] 1f05 6144 mtdblock5
[ 5.390867] (driver?)
[ 5.403870] 1f06 32768 mtdblock6
[ 5.403875] (driver?)
[ 5.416896] 1f07 32768 mtdblock7
[ 5.416901] (driver?)
[ 5.429913] 1f08 20480 mtdblock8
[ 5.429918] (driver?)
[ 5.442925] 1f09 28160 mtdblock9
[ 5.442929] (driver?)
[ 5.455956] 1f0a 81408 mtdblock10
[ 5.455961] (driver?)
[ 5.469135] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 5.485600] Rebooting in 1 seconds..
Its working now! Thanks man
You are the man 
Can you help me here, firmware up and luci is also installed from ssh, however internet is not working and wirelss settings are also not showing, how can I overcome this. Please guide.
Thanks!
