Hello, i have a 1Gb/s connection and a router described above.
After sysupgrade from 21.02.3 my upload speed is like 1/10~ (94 Mbps) of what its supposed\was before on the 21.XX releases (850~ Mbps)
I have Irqbalance, Packet Steering and HW_Offload enabled. (tried with these on 22.03)
Speedtest 21.02.XX
Speedtest 22.03.0
Bufferbloat 22.03
I've also tried upgrading without keeping the .conf option. I didn't tried 22.XX RC versions, so i don't know if this behavior was on those to.
Kernel log:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.10.138 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 11.2.0 r19685-512e76967f) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Sat Sep 3 02:55:34 2022
[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Linksys WRT1900AC v2
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000] On node 0 totalpages: 131072
[ 0.000000] Normal zone: 1152 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 131072 pages, LIFO batch:31
[ 0.000000] percpu: Embedded 11 pages/cpu s16268 r8192 d20596 u45056
[ 0.000000] pcpu-alloc: s16268 r8192 d20596 u45056 alloc=11*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock5 ro rootdelay=1 rootfstype=jffs2 earlyprintk mtdparts=armada-nand:2048K(uboot)ro,256K(u_env),256K(s_env),1m@9m(devinfo),40m@10m(kernel),34m@16m(rootfs),40m@50m(alt_kernel),34m@56m(alt_rootfs),80m@10m(ubifs),-@90m(syscfg)
[ 0.000000] Bootloader command line (ignored): console=ttyS0,115200 root=/dev/mtdblock5 ro rootdelay=1 rootfstype=jffs2 earlyprintk mtdparts=armada-nand:2048K(uboot)ro,256K(u_env),256K(s_env),1m@9m(devinfo),40m@10m(kernel),34m@16m(rootfs),40m@50m(alt_kernel),34m@56m(alt_rootfs),80m@10m(ubifs),-@90m(syscfg)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 506928K/524288K available (8192K kernel code, 642K rwdata, 1104K rodata, 1024K init, 238K bss, 17360K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 D prefetch enabled, offset 1 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
[ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
[ 0.000006] sched_clock: 64 bits at 800MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.000017] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0xb881274fa3, max_idle_ns: 440795210636 ns
[ 0.000030] Switching to timer-based delay loop, resolution 1ns
[ 0.000151] Ignoring duplicate/late registration of read_current_timer delay
[ 0.000158] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.000300] Calibrating delay loop (skipped), value calculated using timer frequency.. 1600.00 BogoMIPS (lpj=8000000)
[ 0.000308] pid_max: default: 32768 minimum: 301
[ 0.000376] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.000381] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.000716] CPU: Testing write buffer coherency: ok
[ 0.000729] CPU0: Spectre v2: using BPIALL workaround
[ 0.000820] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.001052] Setting up static identity map for 0x100000 - 0x100060
[ 0.001126] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
[ 0.001200] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.001259] rcu: Hierarchical SRCU implementation.
[ 0.001326] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.001389] smp: Bringing up secondary CPUs ...
[ 0.001542] Booting CPU 1
[ 0.001693] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.001697] CPU1: Spectre v2: using BPIALL workaround
[ 0.001751] smp: Brought up 1 node, 2 CPUs
[ 0.001756] SMP: Total of 2 processors activated (3200.00 BogoMIPS).
[ 0.001760] CPU: All CPU(s) started in SVC mode.
[ 0.003466] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.003518] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.003527] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.003583] pinctrl core: initialized pinctrl subsystem
[ 0.004156] NET: Registered protocol family 16
[ 0.004703] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.005185] thermal_sys: Registered thermal governor 'step_wise'
[ 0.005732] cpuidle: using governor ladder
[ 0.005899] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
[ 0.005906] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
[ 0.019324] cryptd: max_cpu_qlen set to 1000
[ 0.020332] SCSI subsystem initialized
[ 0.020862] libata version 3.00 loaded.
[ 0.020962] usbcore: registered new interface driver usbfs
[ 0.020984] usbcore: registered new interface driver hub
[ 0.021002] usbcore: registered new device driver usb
[ 0.022137] clocksource: Switched to clocksource arm_global_timer
[ 0.022494] NET: Registered protocol family 2
[ 0.022597] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.023044] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.023071] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.023093] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.023125] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.023166] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.023182] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.023264] NET: Registered protocol family 1
[ 0.023279] PCI: CLS 0 bytes, default 64
[ 0.024502] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.026187] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.026193] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.026599] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.027443] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
[ 0.028307] mvebu-pcie soc:pcie: host bridge /soc/pcie ranges:
[ 0.028331] mvebu-pcie soc:pcie: MEM 0x00f1080000..0x00f1081fff -> 0x0000080000
[ 0.028344] mvebu-pcie soc:pcie: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[ 0.028355] mvebu-pcie soc:pcie: MEM 0x00f1044000..0x00f1045fff -> 0x0000044000
[ 0.028366] mvebu-pcie soc:pcie: MEM 0x00f1048000..0x00f1049fff -> 0x0000048000
[ 0.028376] mvebu-pcie soc:pcie: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 0.028387] mvebu-pcie soc:pcie: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 0.028397] mvebu-pcie soc:pcie: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 0.028407] mvebu-pcie soc:pcie: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 0.028417] mvebu-pcie soc:pcie: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0300000000
[ 0.028427] mvebu-pcie soc:pcie: IO 0xffffffffffffffff..0x00fffffffe -> 0x0300000000
[ 0.028436] mvebu-pcie soc:pcie: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0400000000
[ 0.028444] mvebu-pcie soc:pcie: IO 0xffffffffffffffff..0x00fffffffe -> 0x0400000000
[ 0.028560] mvebu-pcie soc:pcie: PCI host bridge to bus 0000:00
[ 0.028569] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.028576] pci_bus 0000:00: root bus resource [mem 0xf1080000-0xf1081fff] (bus address [0x00080000-0x00081fff])
[ 0.028581] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[ 0.028587] pci_bus 0000:00: root bus resource [mem 0xf1044000-0xf1045fff] (bus address [0x00044000-0x00045fff])
[ 0.028592] pci_bus 0000:00: root bus resource [mem 0xf1048000-0xf1049fff] (bus address [0x00048000-0x00049fff])
[ 0.028596] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[ 0.028601] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 0.028673] pci 0000:00:01.0: [11ab:6820] type 01 class 0x060400
[ 0.028836] pci 0000:00:02.0: [11ab:6820] type 01 class 0x060400
[ 0.029611] PCI: bus0: Fast back to back transfers disabled
[ 0.029617] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.029624] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.029684] pci 0000:01:00.0: [11ab:2a55] type 00 class 0x020000
[ 0.029702] pci 0000:01:00.0: reg 0x10: [mem 0x40000000-0x400fffff 64bit pref]
[ 0.029714] pci 0000:01:00.0: reg 0x18: [mem 0x40100000-0x401fffff 64bit pref]
[ 0.029778] pci 0000:01:00.0: supports D1 D2
[ 0.029783] pci 0000:01:00.0: PME# supported from D0 D1 D3hot D3cold
[ 0.030555] PCI: bus1: Fast back to back transfers disabled
[ 0.030562] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.030634] pci 0000:02:00.0: [11ab:2a55] type 00 class 0x020000
[ 0.030656] pci 0000:02:00.0: reg 0x10: [mem 0x42000000-0x420fffff 64bit pref]
[ 0.030670] pci 0000:02:00.0: reg 0x18: [mem 0x42100000-0x421fffff 64bit pref]
[ 0.030757] pci 0000:02:00.0: supports D1 D2
[ 0.030761] pci 0000:02:00.0: PME# supported from D0 D1 D3hot D3cold
[ 0.030787] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:02.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 0.031553] PCI: bus2: Fast back to back transfers disabled
[ 0.031560] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 0.031588] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe01fffff]
[ 0.031595] pci 0000:00:02.0: BAR 8: assigned [mem 0xe0200000-0xe03fffff]
[ 0.031602] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe00fffff 64bit pref]
[ 0.031613] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0100000-0xe01fffff 64bit pref]
[ 0.031622] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.031629] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe01fffff]
[ 0.031637] pci 0000:02:00.0: BAR 0: assigned [mem 0xe0200000-0xe02fffff 64bit pref]
[ 0.031647] pci 0000:02:00.0: BAR 2: assigned [mem 0xe0300000-0xe03fffff 64bit pref]
[ 0.031657] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 0.031662] pci 0000:00:02.0: bridge window [mem 0xe0200000-0xe03fffff]
[ 0.031915] mv_xor f1060800.xor: Marvell shared XOR driver
[ 0.102526] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 0.102673] mv_xor f1060900.xor: Marvell shared XOR driver
[ 0.182508] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 0.182689] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.183398] printk: console [ttyS0] disabled
[ 0.203485] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 30, base_baud = 12500000) is a 16550A
[ 1.237853] printk: console [ttyS0] enabled
[ 1.243914] loop: module loaded
[ 1.247074] Loading iSCSI transport class v2.0-870.
[ 1.252987] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator
[ 1.260653] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator
[ 1.268211] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator
[ 1.276064] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 1.285156] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 1.294416] scsi host0: ahci-mvebu
[ 1.298080] scsi host1: ahci-mvebu
[ 1.301579] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 49
[ 1.309545] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 49
[ 1.318055] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
[ 1.324454] nand: AMD/Spansion S34ML01G2
[ 1.328393] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.336338] Bad block table found at page 65472, version 0x01
[ 1.342744] Bad block table found at page 65408, version 0x01
[ 1.348973] 10 fixed-partitions partitions found on MTD device pxa3xx_nand-0
[ 1.356064] Creating 10 MTD partitions on "pxa3xx_nand-0":
[ 1.361574] 0x000000000000-0x000000200000 : "u-boot"
[ 1.366873] 0x000000200000-0x000000240000 : "u_env"
[ 1.371942] 0x000000240000-0x000000280000 : "s_env"
[ 1.377012] 0x000000900000-0x000000a00000 : "devinfo"
[ 1.382261] 0x000000a00000-0x000003200000 : "kernel1"
[ 1.387538] 0x000001000000-0x000003200000 : "ubi"
[ 1.392470] 0x000003200000-0x000005a00000 : "kernel2"
[ 1.397742] 0x000003800000-0x000005a00000 : "rootfs2"
[ 1.403029] 0x000005a00000-0x000008000000 : "syscfg"
[ 1.408237] 0x000000280000-0x000000900000 : "unused_area"
[ 1.416057] mv88e6085 f1072004.mdio-mii:00: switch 0x1760 detected: Marvell 88E6176, revision 1
[ 1.585273] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled
[ 1.594174] mvneta f1070000.ethernet eth0: Using hardware mac address c0:56:27:6d:8a:b7
[ 1.602302] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.608858] ehci-pci: EHCI PCI platform driver
[ 1.613349] ehci-platform: EHCI generic platform driver
[ 1.618662] ehci-orion: EHCI orion driver
[ 1.622770] orion-ehci f1058000.usb: EHCI Host Controller
[ 1.628199] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[ 1.635846] orion-ehci f1058000.usb: irq 46, io mem 0xf1058000
[ 1.643379] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.648831] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.672136] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[ 1.678293] hub 1-0:1.0: USB hub found
[ 1.682071] hub 1-0:1.0: 1 port detected
[ 1.686441] usbcore: registered new interface driver usb-storage
[ 1.692624] i2c /dev entries driver
[ 1.698847] orion_wdt: Initial timeout 171 sec
[ 1.703522] sdhci: Secure Digital Host Controller Interface driver
[ 1.709729] sdhci: Copyright(c) Pierre Ossman
[ 1.714197] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.723644] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 1.731255] NET: Registered protocol family 10
[ 1.736181] Segment Routing with IPv6
[ 1.739891] NET: Registered protocol family 17
[ 1.744389] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.757464] 8021q: 802.1Q VLAN Support v1.8
[ 1.761730] Registering SWP/SWPB emulation handler
[ 1.769152] usb_phy_generic usb3_1-phy: dummy supplies not allowed for exclusive requests
[ 1.777581] mv88e6085 f1072004.mdio-mii:00: switch 0x1760 detected: Marvell 88E6176, revision 1
[ 2.126526] mv88e6085 f1072004.mdio-mii:00 lan4 (uninitialized): PHY [mv88e6xxx-1:00] driver [Marvell 88E1540] (irq=63)
[ 2.151746] mv88e6085 f1072004.mdio-mii:00 lan3 (uninitialized): PHY [mv88e6xxx-1:01] driver [Marvell 88E1540] (irq=64)
[ 2.174549] mv88e6085 f1072004.mdio-mii:00 lan2 (uninitialized): PHY [mv88e6xxx-1:02] driver [Marvell 88E1540] (irq=65)
[ 2.199080] mv88e6085 f1072004.mdio-mii:00 lan1 (uninitialized): PHY [mv88e6xxx-1:03] driver [Marvell 88E1540] (irq=66)
[ 2.221767] mv88e6085 f1072004.mdio-mii:00 wan (uninitialized): PHY [mv88e6xxx-1:04] driver [Marvell 88E1540] (irq=67)
[ 2.253974] mv88e6085 f1072004.mdio-mii:00: configuring for fixed/ link mode
[ 2.261169] DSA: tree 0 setup
[ 2.264316] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 2.269660] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 2
[ 2.277243] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
[ 2.286527] xhci-hcd f10f8000.usb3: irq 51, io mem 0xf10f8000
[ 2.292611] hub 2-0:1.0: USB hub found
[ 2.296400] hub 2-0:1.0: 1 port detected
[ 2.300451] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 2.305798] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 3
[ 2.313333] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed
[ 2.319727] mv88e6085 f1072004.mdio-mii:00: Link is Up - 1Gbps/Full - flow control off
[ 2.327706] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.336013] hub 3-0:1.0: USB hub found
[ 2.339790] hub 3-0:1.0: 1 port detected
[ 2.344263] UBI: auto-attach mtd5
[ 2.347594] ubi0: attaching mtd5
[ 2.526025] ubi0: scanning is finished
[ 2.537394] ubi0: attached mtd5 (name "ubi", size 34 MiB)
[ 2.542825] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 2.549727] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 2.556549] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 2.563542] ubi0: good PEBs: 272, bad PEBs: 0, corrupted PEBs: 0
[ 2.569572] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 2.576827] ubi0: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 1635066095
[ 2.585999] ubi0: available PEBs: 0, total reserved PEBs: 272, PEBs reserved for bad PEB handling: 20
[ 2.595637] ubi0: background thread "ubi_bgt0d" started, PID 810
[ 2.601886] block ubiblock0_0: created from ubi0:0(rootfs)
[ 2.607404] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 2.614712] Waiting 1 sec before mounting root device...
[ 3.694618] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 3.702382] Freeing unused kernel memory: 1024K
[ 3.732286] Run /sbin/init as init process
[ 3.736400] with arguments:
[ 3.736402] /sbin/init
[ 3.736403] earlyprintk
[ 3.736405] with environment:
[ 3.736407] HOME=/
[ 3.736409] TERM=linux
[ 3.736411] mangled_fs=jffs2
[ 3.736414] mtdparts=armada-nand:2048K(uboot)ro,256K(u_env),256K(s_env),1m@9m(devinfo),40m@10m(kernel),34m@16m(rootfs),40m@50m(alt_kernel),34m@56m(alt_rootfs),80m@10m(ubifs),-@90m(syscfg)
[ 3.947774] init: Console is alive
[ 3.951275] init: - watchdog -
[ 4.246073] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.298763] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.306697] init: - preinit -
[ 4.655595] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.679275] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.905570] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.978918] mvneta f1070000.ethernet eth0: configuring for fixed/rgmii-id link mode
[ 4.987061] mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 4.992165] mv88e6085 f1072004.mdio-mii:00 lan1: configuring for phy/gmii link mode
[ 5.005008] 8021q: adding VLAN 0 to HW filter on device lan1
[ 5.010710] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 9.078773] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 9.092161] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 919
[ 9.124918] UBIFS (ubi0:1): recovery needed
[ 9.213580] UBIFS (ubi0:1): recovery completed
[ 9.218084] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 9.225954] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 9.235914] UBIFS (ubi0:1): FS size: 26664960 bytes (25 MiB, 210 LEBs), journal size 1396736 bytes (1 MiB, 11 LEBs)
[ 9.246395] UBIFS (ubi0:1): reserved for root: 1259451 bytes (1229 KiB)
[ 9.253040] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 72740FC2-9CC3-4E63-AF8B-790641B3561A, small LPT model
[ 9.270071] mount_root: switching to ubifs overlay
[ 9.333620] ubi1: attaching mtd8
[ 9.527838] ubi1: scanning is finished
[ 9.539285] ubi1: attached mtd8 (name "syscfg", size 38 MiB)
[ 9.544983] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 9.551886] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 9.558709] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 9.565702] ubi1: good PEBs: 296, bad PEBs: 8, corrupted PEBs: 0
[ 9.571733] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 9.578988] ubi1: max/mean erase counter: 1212/745, WL threshold: 4096, image sequence number: 1395122904
[ 9.588596] ubi1: available PEBs: 0, total reserved PEBs: 296, PEBs reserved for bad PEB handling: 12
[ 9.597863] ubi1: background thread "ubi_bgt1d" started, PID 930
[ 9.612656] UBIFS (ubi1:0): Mounting in unauthenticated mode
[ 9.622168] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 934
[ 9.719444] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "syscfg"
[ 9.726881] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 9.736842] UBIFS (ubi1:0): FS size: 34283520 bytes (32 MiB, 270 LEBs), journal size 1777664 bytes (1 MiB, 14 LEBs)
[ 9.747323] UBIFS (ubi1:0): reserved for root: 1619295 bytes (1581 KiB)
[ 9.753970] UBIFS (ubi1:0): media format: w4/r0 (latest is w5/r0), UUID 0AECDAB1-7D95-4663-9111-6A679A4847D6, small LPT model
[ 9.767769] urandom-seed: Seeding with /etc/urandom.seed
[ 9.864743] procd: - early -
[ 9.867683] procd: - watchdog -
[ 10.420214] procd: - watchdog -
[ 10.424841] procd: - ubus -
[ 10.463493] random: ubusd: uninitialized urandom read (4 bytes read)
[ 10.478785] random: ubusd: uninitialized urandom read (4 bytes read)
[ 10.485666] random: ubusd: uninitialized urandom read (4 bytes read)
[ 10.496031] procd: - init -
[ 10.859602] urngd: v1.0.2 started.
[ 10.869857] kmodloader: loading kernel modules from /etc/modules.d/*
[ 10.895472] random: crng init done
[ 10.898894] random: 23 urandom warning(s) missed due to ratelimiting
[ 11.017275] Loading modules backported from Linux version v5.15.58-0-g7d8048d4e064
[ 11.024896] Backport generated by backports.git v5.15.58-1-0-g42a95ce7
[ 11.049647] <<Marvell Mac80211 Wireless PCIE Network Driver version 10.3.8.0-20181210>>
[ 11.057729] pci 0000:00:01.0: enabling device (0140 -> 0142)
[ 11.063519] ieee80211 phy0: priv->pcmd_buf = ead02b61 priv->pphys_cmd_buf = ae738ad4
[ 11.082157] ieee80211 phy0: fw download start
[ 11.198903] ieee80211 phy0: FwSize = 118776 downloaded Size = 118776 curr_iteration 65496
[ 12.072132] ieee80211 phy0: fw download complete
[ 12.072145] ieee80211 phy0: device node: pcie@1,0
[ 12.077392] ieee80211 phy0: pcmd = ead02b61
[ 12.095430] ieee80211 phy0: firmware version: 0x702091a
[ 12.118149] ieee80211 phy0: firmware region code: 0
[ 12.156258] ieee80211 phy0: regdomain: FCC
[ 12.156263] ieee80211 phy0: Channel: 36: 0x0 0x0 0xf
[ 12.156269] ieee80211 phy0: 12 12 12 12 12 12 12 12 10 10 10 10 f f f f
[ 12.156273] ieee80211 phy0: Channel: 40: 0x0 0x0 0xf
[ 12.156278] ieee80211 phy0: 16 16 16 16 16 16 16 16 16 16 16 16 f f f f
[ 12.156281] ieee80211 phy0: Channel: 44: 0x0 0x0 0xf
[ 12.156287] ieee80211 phy0: 16 16 16 16 16 16 16 16 16 16 16 16 f f f f
[ 12.156290] ieee80211 phy0: Channel: 48: 0x0 0x0 0xf
[ 12.156295] ieee80211 phy0: 16 16 16 16 16 16 16 16 16 16 16 16 f f f f
[ 12.156298] ieee80211 phy0: Channel: 52: 0x0 0x0 0xf
[ 12.156303] ieee80211 phy0: 11 11 11 11 10 10 10 10 12 12 12 12 10 10 10 10
[ 12.156306] ieee80211 phy0: Channel: 56: 0x0 0x0 0xf
[ 12.156312] ieee80211 phy0: 11 11 11 11 10 10 10 10 12 12 12 12 10 10 10 10
[ 12.156315] ieee80211 phy0: Channel: 60: 0x0 0x0 0xf
[ 12.156320] ieee80211 phy0: 11 11 11 11 10 10 10 10 12 12 12 12 10 10 10 10
[ 12.156323] ieee80211 phy0: Channel: 64: 0x0 0x0 0xf
[ 12.156328] ieee80211 phy0: 11 11 11 11 10 10 10 10 12 12 12 12 10 10 10 10
[ 12.156332] ieee80211 phy0: Channel: 100: 0x0 0x0 0xf
[ 12.156337] ieee80211 phy0: 10 10 10 10 11 11 11 11 12 12 12 12 10 10 10 10
[ 12.156340] ieee80211 phy0: Channel: 104: 0x0 0x0 0xf
[ 12.156345] ieee80211 phy0: 11 11 11 11 10 10 10 10 12 12 12 12 10 10 10 10
[ 12.156348] ieee80211 phy0: Channel: 108: 0x0 0x0 0xf
[ 12.156354] ieee80211 phy0: 11 11 11 11 10 10 10 10 11 11 11 11 10 10 10 10
[ 12.156357] ieee80211 phy0: Channel: 112: 0x0 0x0 0xf
[ 12.156362] ieee80211 phy0: 11 11 11 11 10 10 10 10 11 11 11 11 10 10 10 10
[ 12.156365] ieee80211 phy0: Channel: 116: 0x0 0x0 0xf
[ 12.156370] ieee80211 phy0: 11 11 11 11 10 10 10 10 11 11 11 11 10 10 10 10
[ 12.156373] ieee80211 phy0: Channel: 120: 0x0 0x0 0xf
[ 12.156378] ieee80211 phy0: 11 11 11 11 10 10 10 10 11 11 11 11 10 10 10 10
[ 12.156381] ieee80211 phy0: Channel: 124: 0x0 0x0 0xf
[ 12.156387] ieee80211 phy0: 11 11 11 11 10 10 10 10 11 11 11 11 10 10 10 10
[ 12.156390] ieee80211 phy0: Channel: 128: 0x0 0x0 0xf
[ 12.156395] ieee80211 phy0: 11 11 11 11 10 10 10 10 11 11 11 11 10 10 10 10
[ 12.156398] ieee80211 phy0: Channel: 132: 0x0 0x0 0xf
[ 12.156403] ieee80211 phy0: 11 11 11 11 10 10 10 10 11 11 11 11 10 10 10 10
[ 12.156406] ieee80211 phy0: Channel: 136: 0x0 0x0 0xf
[ 12.156412] ieee80211 phy0: 11 11 11 11 10 10 10 10 11 11 11 11 10 10 10 10
[ 12.156415] ieee80211 phy0: Channel: 140: 0x0 0x0 0xf
[ 12.156420] ieee80211 phy0: 11 11 11 11 10 10 10 10 11 11 11 11 10 10 10 10
[ 12.156423] ieee80211 phy0: Channel: 149: 0x0 0x0 0xf
[ 12.156428] ieee80211 phy0: 16 16 16 16 16 16 16 16 15 15 15 15 15 15 15 15
[ 12.156431] ieee80211 phy0: Channel: 153: 0x0 0x0 0xf
[ 12.156437] ieee80211 phy0: 16 16 16 16 15 15 15 15 15 15 15 15 15 15 15 15
[ 12.156440] ieee80211 phy0: Channel: 157: 0x0 0x0 0xf
[ 12.156445] ieee80211 phy0: 16 16 16 16 15 15 15 15 15 15 15 15 15 15 15 15
[ 12.156448] ieee80211 phy0: Channel: 161: 0x0 0x0 0xf
[ 12.156453] ieee80211 phy0: 16 16 16 16 15 15 15 15 15 15 15 15 15 15 15 15
[ 12.156456] ieee80211 phy0: Channel: 165: 0x0 0x0 0xf
[ 12.156462] ieee80211 phy0: 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15
[ 12.156951] ieee80211 phy0: 2G disabled, 5G enabled
[ 12.161852] ieee80211 phy0: 4 TX antennas, 4 RX antennas
[ 12.167373] pci 0000:00:02.0: enabling device (0140 -> 0142)
[ 12.173239] ieee80211 phy1: priv->pcmd_buf = 657655b1 priv->pphys_cmd_buf = ddaef9bf
[ 12.179791] ieee80211 phy1: fw download start
[ 12.297573] ieee80211 phy1: FwSize = 118776 downloaded Size = 118776 curr_iteration 65510
[ 13.162141] ieee80211 phy1: fw download complete
[ 13.162167] ieee80211 phy1: device node: pcie@2,0
[ 13.167379] ieee80211 phy1: pcmd = 657655b1
[ 13.185414] ieee80211 phy1: firmware version: 0x702091a
[ 13.208152] ieee80211 phy1: firmware region code: 0
[ 13.242306] ieee80211 phy1: regdomain: FCC
[ 13.242312] ieee80211 phy1: Channel: 1: 0x0 0x0 0xf
[ 13.242318] ieee80211 phy1: 17 10 10 10 f f f f e e e e 0 0 0 0
[ 13.242322] ieee80211 phy1: Channel: 2: 0x0 0x0 0xf
[ 13.242327] ieee80211 phy1: 18 16 16 16 16 16 16 14 11 11 11 11 0 0 0 0
[ 13.242330] ieee80211 phy1: Channel: 3: 0x0 0x0 0xf
[ 13.242335] ieee80211 phy1: 18 16 16 16 16 16 16 14 11 11 11 11 0 0 0 0
[ 13.242338] ieee80211 phy1: Channel: 4: 0x0 0x0 0xf
[ 13.242344] ieee80211 phy1: 18 16 16 16 16 16 16 14 11 11 11 11 0 0 0 0
[ 13.242347] ieee80211 phy1: Channel: 5: 0x0 0x0 0xf
[ 13.242352] ieee80211 phy1: 18 16 16 16 16 16 16 14 11 11 11 11 0 0 0 0
[ 13.242355] ieee80211 phy1: Channel: 6: 0x0 0x0 0xf
[ 13.242361] ieee80211 phy1: 18 16 16 16 16 16 16 14 11 11 11 11 0 0 0 0
[ 13.242364] ieee80211 phy1: Channel: 7: 0x0 0x0 0xf
[ 13.242369] ieee80211 phy1: 18 16 16 16 16 16 16 14 11 11 11 11 0 0 0 0
[ 13.242372] ieee80211 phy1: Channel: 8: 0x0 0x0 0xf
[ 13.242377] ieee80211 phy1: 18 16 16 16 16 16 16 14 11 11 11 11 0 0 0 0
[ 13.242381] ieee80211 phy1: Channel: 9: 0x0 0x0 0xf
[ 13.242386] ieee80211 phy1: 18 16 16 16 16 16 16 14 11 11 11 11 0 0 0 0
[ 13.242389] ieee80211 phy1: Channel: 10: 0x0 0x0 0xf
[ 13.242395] ieee80211 phy1: 18 16 16 16 16 16 16 14 11 11 11 11 0 0 0 0
[ 13.242398] ieee80211 phy1: Channel: 11: 0x0 0x0 0xf
[ 13.242403] ieee80211 phy1: 17 12 12 12 13 13 13 13 f f f f 0 0 0 0
[ 13.243075] ieee80211 phy1: 2G enabled, 5G disabled
[ 13.247984] ieee80211 phy1: 4 TX antennas, 4 RX antennas
[ 13.270328] PPP generic driver version 2.4.2
[ 13.275789] NET: Registered protocol family 24
[ 13.282091] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 15.729130] mvneta f1070000.ethernet eth0: Link is Down
[ 15.745847] mvneta f1070000.ethernet eth0: configuring for fixed/rgmii-id link mode
[ 15.753707] mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 15.761587] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 15.768864] mv88e6085 f1072004.mdio-mii:00 lan1: configuring for phy/gmii link mode
[ 15.782346] 8021q: adding VLAN 0 to HW filter on device lan1
[ 15.830904] br-lan: port 1(lan1) entered blocking state
[ 15.836189] br-lan: port 1(lan1) entered disabled state
[ 15.842019] device lan1 entered promiscuous mode
[ 15.846765] device eth0 entered promiscuous mode
[ 15.923978] mv88e6085 f1072004.mdio-mii:00 lan2: configuring for phy/gmii link mode
[ 15.954477] 8021q: adding VLAN 0 to HW filter on device lan2
[ 15.960293] br-lan: port 2(lan2) entered blocking state
[ 15.965653] br-lan: port 2(lan2) entered disabled state
[ 15.982489] device lan2 entered promiscuous mode
[ 16.002656] mv88e6085 f1072004.mdio-mii:00 lan3: configuring for phy/gmii link mode
[ 16.019328] 8021q: adding VLAN 0 to HW filter on device lan3
[ 16.116170] br-lan: port 3(lan3) entered blocking state
[ 16.121428] br-lan: port 3(lan3) entered disabled state
[ 16.142505] device lan3 entered promiscuous mode
[ 16.160388] mv88e6085 f1072004.mdio-mii:00 lan4: configuring for phy/gmii link mode
[ 16.179459] 8021q: adding VLAN 0 to HW filter on device lan4
[ 16.249257] br-lan: port 4(lan4) entered blocking state
[ 16.254539] br-lan: port 4(lan4) entered disabled state
[ 16.272713] device lan4 entered promiscuous mode
[ 16.291721] mv88e6085 f1072004.mdio-mii:00 wan: configuring for phy/gmii link mode
[ 16.304859] 8021q: adding VLAN 0 to HW filter on device wan
[ 17.746157] mv88e6085 f1072004.mdio-mii:00 lan2: Link is Up - 100Mbps/Full - flow control rx/tx
[ 17.754917] br-lan: port 2(lan2) entered blocking state
[ 17.760165] br-lan: port 2(lan2) entered forwarding state
[ 17.766301] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 19.526159] mv88e6085 f1072004.mdio-mii:00 wan: Link is Up - 1Gbps/Full - flow control off
[ 19.534489] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready
[ 22.246164] mv88e6085 f1072004.mdio-mii:00 lan3: Link is Up - 1Gbps/Full - flow control rx/tx
[ 22.254794] br-lan: port 3(lan3) entered blocking state
[ 22.260044] br-lan: port 3(lan3) entered forwarding state
Dear,
you have one device with 100mbit lan connection, disable flow control on that lan device (lan2 from log) with ethtool
last post I write solution... install ethtool pkg
Edit...
the best thing is to add a hotplug script on iface
#!/bin/sh
if [ "${ACTION}" = "ifup" ]; then
if [ "${INTERFACE}" = "lan" ]; then
logger -t hotplug "Enabling disabling FLOW Control"
ethtool -A lan2 autoneg on rx on tx on
ethtool -A lan3 autoneg on rx on tx on
ethtool -A lan2 autoneg off rx off tx off
ethtool -A lan3 autoneg off rx off tx off
fi
fi
modify lan2-3 in case your device with 10-100 is connected to other lan port
This topic was automatically closed 10 days after the last reply. New replies are no longer allowed.