I can get to shell via both com port on PuTTY and via direct connect to HDMI but non of the network ports are working. Tried all the factory reset guides and even tried to a fresh reinstall from USB drive but nothing is working for me. It was running 24.10.4 and I tried to upgrade to 24.10.5 and that is when things went south very fast.
Reinstall ?
Won’t let me. No network ports work and will not let me install from USB drive.
Then perhaps something else broke not only the OS ?
I’m pretty sure it was all me. Flashed the wrong firmware. Not sure how to recover from that.
You can't kill an x86.
You should still get BIOS output.
1 Like
I can go into the BIOS, I can get into the shell…. It just will not let me reinstall the image file 
What shell ? UEFI ? GRUB ? Openwrt over serial?
Over serial
You're not answering the question.
1 Like
“f you decide to go the console route, keep in mind that OpenWrt requires console connection at 115200 bits per second (bps). The SG105w BIOS, meanwhile, expects a connection at a lower speed, 38400 bps. So if you want to work with OpenWrt, connect at 115200; if you need to get into BIOS, connect at 38400.”
From PuTTY I can connect and access root
1 Like
You can access an OpenWrt shell via putty. Fine. So you can flash a new sysupgrade image. You just need to get the sysupgrade image onto the box. I assume you're having problems getting the file off USB stick because there's no USB stick driver?
Worst case, boot off USB stick using a system recovery USB stick (like this https://www.system-rescue.org/Download/ ) use that system to copy a sysupgrade image to the box, then reboot into openwrt and flash the sysupgrade image you copied over.
1 Like
Run logread -f via serial, try connecting one Ethernet port at a time.
Post any reaction/output.
Obviously something needs to be hooked up to the other end of the ethernet cable too ,)
1 Like
I get no output at all from any of the 4 ports. (with the other end connected to my temp router 
)
Here is some of the errors that show when I boot the device while I am connected via serial:
-ash: syntax error: unexpected "("
root@OpenWrt:~# [ 9.688302] i2c_dev: i2c /dev entries driver
ash: missing ]
root@OpenWrt:~# [ 9.703403] e1000e: Intel(R) PRO/1000 Network Driver
-ash: syntax error: unexpected "("
root@OpenWrt:~# [ 9.709176] e1000e: Copyright(c) 1999 - 2015 Intel Corporatio
n.
-ash: syntax error: unexpected "("
root@OpenWrt:~# [ 9.734102] PPP generic driver version 2.4.2
ash: missing ]
root@OpenWrt:~# [ 9.739649] NET: Registered PF_PPPOX protocol family
ash: missing ]
root@OpenWrt:~# [ 9.765132] urngd: v1.0.2 started.
ash: missing ]
root@OpenWrt:~# [ 9.775324] Console: switching to colour dummy device 80x25
ash: missing ]
root@OpenWrt:~# [ 9.782348] i915 0000:00:02.0: [drm] Finished loading DMC fir
mware i915/bxt_d
mc_ver1_07.bin (v1.7)
-ash: syntax error: unexpected "("
root@OpenWrt:~# [ 10.194467] i915 0000:00:02.0: [drm] [ENCODER:110:DDI A/PHY A
] failed to retr
ieve link info, disabling eDP
ash: missing ]
root@OpenWrt:~# [ 10.207817] [drm] Initialized i915 1.6.0 20201103 for 0000:00
:02.0 on minor 0
ash: missing ]
root@OpenWrt:~# [ 10.216709] ACPI: video: Video Device [GFX0] (multi-head: yes
rom: no post:
no)
-ash: syntax error: unexpected "("
root@OpenWrt:~# [ 10.224648] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS
:00/PNP0A08:00/L
NXVIDEO:00/input/input2
ash: missing ]
root@OpenWrt:~# [ 10.236746] i915 0000:00:02.0: [drm] Cannot find any crtc or
sizes
ash: missing ]
root@OpenWrt:~# [ 10.245667] kmodloader: done loading kernel modules from /etc
/modules.d/*
ash: missing ]
root@OpenWrt:~# [ 10.245867] i915 0000:00:02.0: [drm] Cannot find any crtc or
sizes
ash: missing ]
root@OpenWrt:~# [ 10.261127] i915 0000:00:02.0: [drm] Cannot find any crtc or
sizes
ash: missing ]
root@OpenWrt:~# logread -f
Is there a /etc/config/network file ?
Rename it, and reboot.
Post full boot log afterwards.
There was a network file and I renamed as you asked and rebooted. I did notice on reboot with the network cable connected to WAN port the lights did blink while rebooting so I believe the ports are good but they go out once the unit is booted into openwrt. Here is 1/3 the log as requested and I will post the other 2 thirds in posts below as the forum gave me an error about it being to long:
[ 0.000000] Linux version 6.6.119 (builder@buildhost) (x86_64-openwrt-linux-m usl-gcc (OpenWrt GCC 13.3.0 r29087-d9c5716d1d) 13.3.0, GNU ld (GNU Binutils) 2.4 2) #0 SMP Wed Dec 17 21:08:22 2025
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz root=PARTUUID=e73bfb4e-27c f-383d-5de5-fbca2572be02 rootwait console=tty1 console=ttyS0,115200n8 noinitrd
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000003efff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000003f000-0x000000000003ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000040000-0x000000000009efff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009f000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000000fffffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000010000000-0x0000000012150fff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000012151000-0x0000000077970fff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000077971000-0x0000000079a6bfff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000079a6c000-0x0000000079a7bfff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x0000000079a7c000-0x0000000079e61fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x0000000079e62000-0x000000007a1aafff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007a1ab000-0x000000007a520fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007a521000-0x000000007a521fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000007a522000-0x000000007a54bfff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007a54c000-0x000000007aae1fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007aae2000-0x000000007aae3fff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007aae4000-0x000000007affffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007b000000-0x000000007fffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000d0000000-0x00000000d0ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fe042000-0x00000000fe044fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fe900000-0x00000000fe902fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed01000-0x00000000fed01fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000017fffffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] APIC: Static calls initialized
[ 0.000000] e820: update [mem 0x71613018-0x71623057] usable ==> usable
[ 0.000000] e820: update [mem 0x71613018-0x71623057] usable ==> usable
[ 0.000000] e820: update [mem 0x71603018-0x71612057] usable ==> usable
[ 0.000000] e820: update [mem 0x71603018-0x71612057] usable ==> usable
[ 0.000000] extended physical RAM map:
[ 0.000000] reserve setup_data: [mem 0x0000000000000000-0x000000000003efff] u sable
[ 0.000000] reserve setup_data: [mem 0x000000000003f000-0x000000000003ffff] r eserved
[ 0.000000] reserve setup_data: [mem 0x0000000000040000-0x000000000009efff] u sable
[ 0.000000] reserve setup_data: [mem 0x000000000009f000-0x00000000000fffff] r eserved
[ 0.000000] reserve setup_data: [mem 0x0000000000100000-0x000000000fffffff] u sable
[ 0.000000] reserve setup_data: [mem 0x0000000010000000-0x0000000012150fff] r eserved
[ 0.000000] reserve setup_data: [mem 0x0000000012151000-0x0000000071603017] u sable
[ 0.000000] reserve setup_data: [mem 0x0000000071603018-0x0000000071612057] u sable
[ 0.000000] reserve setup_data: [mem 0x0000000071612058-0x0000000071613017] u sable
[ 0.000000] reserve setup_data: [mem 0x0000000071613018-0x0000000071623057] u sable
[ 0.000000] reserve setup_data: [mem 0x0000000071623058-0x0000000077970fff] u sable
[ 0.000000] reserve setup_data: [mem 0x0000000077971000-0x0000000079a6bfff] r eserved
[ 0.000000] reserve setup_data: [mem 0x0000000079a6c000-0x0000000079a7bfff] A CPI data
[ 0.000000] reserve setup_data: [mem 0x0000000079a7c000-0x0000000079e61fff] A CPI NVS
[ 0.000000] reserve setup_data: [mem 0x0000000079e62000-0x000000007a1aafff] r eserved
[ 0.000000] reserve setup_data: [mem 0x000000007a1ab000-0x000000007a520fff] u sable
[ 0.000000] reserve setup_data: [mem 0x000000007a521000-0x000000007a521fff] A CPI NVS
[ 0.000000] reserve setup_data: [mem 0x000000007a522000-0x000000007a54bfff] r eserved
[ 0.000000] reserve setup_data: [mem 0x000000007a54c000-0x000000007aae1fff] u sable
[ 0.000000] reserve setup_data: [mem 0x000000007aae2000-0x000000007aae3fff] r eserved
[ 0.000000] reserve setup_data: [mem 0x000000007aae4000-0x000000007affffff] u sable
[ 0.000000] reserve setup_data: [mem 0x000000007b000000-0x000000007fffffff] r eserved
[ 0.000000] reserve setup_data: [mem 0x00000000d0000000-0x00000000d0ffffff] r eserved
[ 0.000000] reserve setup_data: [mem 0x00000000e0000000-0x00000000efffffff] r eserved
[ 0.000000] reserve setup_data: [mem 0x00000000fe042000-0x00000000fe044fff] r eserved
[ 0.000000] reserve setup_data: [mem 0x00000000fe900000-0x00000000fe902fff] r eserved
[ 0.000000] reserve setup_data: [mem 0x00000000fec00000-0x00000000fec00fff] r eserved
[ 0.000000] reserve setup_data: [mem 0x00000000fed01000-0x00000000fed01fff] r eserved
[ 0.000000] reserve setup_data: [mem 0x00000000fee00000-0x00000000fee00fff] r eserved
[ 0.000000] reserve setup_data: [mem 0x00000000ff000000-0x00000000ffffffff] r eserved
[ 0.000000] reserve setup_data: [mem 0x0000000100000000-0x000000017fffffff] u sable
[ 0.000000] efi: EFI v2.5 by American Megatrends
[ 0.000000] efi: ACPI=0x79e50000 ACPI 2.0=0x79e50000 SMBIOS=0x7a03d000 SMBIOS 3.0=0x7a03c000 ESRT=0x7699a798
[ 0.000000] efi: Remove mem36: MMIO range=[0xd0000000-0xd0ffffff] (16MB) from e820 map
[ 0.000000] e820: remove [mem 0xd0000000-0xd0ffffff] reserved
[ 0.000000] efi: Remove mem37: MMIO range=[0xe0000000-0xefffffff] (256MB) fro m e820 map
[ 0.000000] e820: remove [mem 0xe0000000-0xefffffff] reserved
[ 0.000000] efi: Not removing mem38: MMIO range=[0xfe042000-0xfe042fff] (4KB) from e820 map
[ 0.000000] efi: Not removing mem39: MMIO range=[0xfe043000-0xfe043fff] (4KB) from e820 map
[ 0.000000] efi: Not removing mem40: MMIO range=[0xfe044000-0xfe044fff] (4KB) from e820 map
[ 0.000000] efi: Not removing mem41: MMIO range=[0xfe900000-0xfe902fff] (12KB ) from e820 map
[ 0.000000] efi: Not removing mem42: MMIO range=[0xfec00000-0xfec00fff] (4KB) from e820 map
[ 0.000000] efi: Not removing mem43: MMIO range=[0xfed01000-0xfed01fff] (4KB) from e820 map
[ 0.000000] efi: Not removing mem44: MMIO range=[0xfee00000-0xfee00fff] (4KB) from e820 map
[ 0.000000] efi: Remove mem45: MMIO range=[0xff000000-0xffffffff] (16MB) from e820 map
[ 0.000000] e820: remove [mem 0xff000000-0xffffffff] reserved
[ 0.000000] SMBIOS 3.0.0 present.
[ 0.000000] DMI: Sophos XG/Default string, BIOS 5.12 (Z131-014) 01/05/2018
[ 0.000000] tsc: Detected 1593.600 MHz processor
[ 0.001584] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.001590] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.001611] last_pfn = 0x180000 max_arch_pfn = 0x400000000
[ 0.001620] MTRR map: 9 entries (5 fixed + 4 variable; max 25), built from 10 variable MTRRs
[ 0.001625] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT
[ 0.001708] last_pfn = 0x7b000 max_arch_pfn = 0x400000000
[ 0.007547] found SMP MP-table at [mem 0x000fcc00-0x000fcc0f]
[ 0.007562] esrt: Reserving ESRT space from 0x000000007699a798 to 0x000000007 699a7d0.
[ 0.007573] e820: update [mem 0x7699a000-0x7699afff] usable ==> reserved
[ 0.007608] Using GB pages for direct mapping
[ 0.010771] Secure boot disabled
[ 0.010775] ACPI: Early table checksum verification disabled
[ 0.010781] ACPI: RSDP 0x0000000079E50000 000024 (v02 ALASKA)
[ 0.010789] ACPI: XSDT 0x0000000079E500B0 0000CC (v01 ALASKA A M I 0107200 9 AMI 00010013)
[ 0.010800] ACPI: FACP 0x0000000079E590B0 000114 (v06 ALASKA A M I 0107200 9 AMI 00010013)
[ 0.010810] ACPI: DSDT 0x0000000079E50220 008E81 (v02 ALASKA A M I 0107200 9 INTL 20120913)
[ 0.010817] ACPI: FACS 0x0000000079E61080 000040
[ 0.010822] ACPI: FPDT 0x0000000079E591D0 000044 (v01 ALASKA A M I 0107200 9 AMI 00010013)
[ 0.010828] ACPI: FIDT 0x0000000079E59220 00009C (v01 ALASKA A M I 0107200 9 AMI 00010013)
[ 0.010833] ACPI: MCFG 0x0000000079E592C0 00003C (v01 ALASKA A M I 0107200 9 MSFT 00000097)
[ 0.010839] ACPI: HROT 0x0000000079E59300 0000DB (v01 INTEL EDK2 0000000 5 INTL 0100000D)
[ 0.010845] ACPI: DBG2 0x0000000079E593E0 000072 (v00 INTEL EDK2 0000000 3 BRXT 0100000D)
[ 0.010851] ACPI: DBGP 0x0000000079E59460 000034 (v01 INTEL EDK2 0000000 3 BRXT 0100000D)
[ 0.010857] ACPI: HPET 0x0000000079E594A0 000038 (v01 INTEL EDK2 0000000 3 BRXT 0100000D)
[ 0.010863] ACPI: LPIT 0x0000000079E594E0 00005C (v01 INTEL EDK2 0000000 3 BRXT 0100000D)
[ 0.010868] ACPI: APIC 0x0000000079E59540 000084 (v03 INTEL EDK2 0000000 3 BRXT 0100000D)
[ 0.010874] ACPI: NPKT 0x0000000079E595D0 000065 (v01 INTEL EDK2 0000000 3 BRXT 0100000D)
[ 0.010880] ACPI: PRAM 0x0000000079E59640 000030 (v01 INTEL EDK2 0000000 3 BRXT 0100000D)
[ 0.010886] ACPI: WSMT 0x0000000079E59670 000028 (v01 INTEL EDK2 0000000 3 BRXT 0100000D)
[ 0.010891] ACPI: SSDT 0x0000000079E596A0 000B53 (v02 INTEL UsbCTabl 0000000 3 BRXT 0100000D)
[ 0.010897] ACPI: SSDT 0x0000000079E5A200 00199B (v01 Intel_ Platform 0000100 0 INTL 20120913)
[ 0.010903] ACPI: SSDT 0x0000000079E5BBA0 00072B (v02 CpuRef CpuSsdt 0000300 0 INTL 20120913)
[ 0.010910] ACPI: SSDT 0x0000000079E5C2D0 00032D (v02 PmRef Cpu0Tst 0000300 0 INTL 20120913)
[ 0.010916] ACPI: SSDT 0x0000000079E5C600 00017C (v02 PmRef ApTst 0000300 0 INTL 20120913)
[ 0.010921] ACPI: SSDT 0x0000000079E5C780 002760 (v02 SaSsdt SaSsdt 0000300 0 INTL 20120913)
[ 0.010927] ACPI: UEFI 0x0000000079E5EEE0 000042 (v01 ALASKA A M I 0000000 0 00000000)
[ 0.010933] ACPI: WDAT 0x0000000079E5EF30 000104 (v01 0000000 0 00000000)
[ 0.010938] ACPI: Reserving FACP table memory at [mem 0x79e590b0-0x79e591c3]
[ 0.010941] ACPI: Reserving DSDT table memory at [mem 0x79e50220-0x79e590a0]
[ 0.010944] ACPI: Reserving FACS table memory at [mem 0x79e61080-0x79e610bf]
[ 0.010946] ACPI: Reserving FPDT table memory at [mem 0x79e591d0-0x79e59213]
[ 0.010948] ACPI: Reserving FIDT table memory at [mem 0x79e59220-0x79e592bb]
[ 0.010950] ACPI: Reserving MCFG table memory at [mem 0x79e592c0-0x79e592fb]
[ 0.010952] ACPI: Reserving HROT table memory at [mem 0x79e59300-0x79e593da]
[ 0.010954] ACPI: Reserving DBG2 table memory at [mem 0x79e593e0-0x79e59451]
[ 0.010956] ACPI: Reserving DBGP table memory at [mem 0x79e59460-0x79e59493]
[ 0.010959] ACPI: Reserving HPET table memory at [mem 0x79e594a0-0x79e594d7]
[ 0.010961] ACPI: Reserving LPIT table memory at [mem 0x79e594e0-0x79e5953b]
[ 0.010963] ACPI: Reserving APIC table memory at [mem 0x79e59540-0x79e595c3]
[ 0.010965] ACPI: Reserving NPKT table memory at [mem 0x79e595d0-0x79e59634]
[ 0.010967] ACPI: Reserving PRAM table memory at [mem 0x79e59640-0x79e5966f]
[ 0.010969] ACPI: Reserving WSMT table memory at [mem 0x79e59670-0x79e59697]
[ 0.010972] ACPI: Reserving SSDT table memory at [mem 0x79e596a0-0x79e5a1f2]
[ 0.010974] ACPI: Reserving SSDT table memory at [mem 0x79e5a200-0x79e5bb9a]
[ 0.010976] ACPI: Reserving SSDT table memory at [mem 0x79e5bba0-0x79e5c2ca]
[ 0.010978] ACPI: Reserving SSDT table memory at [mem 0x79e5c2d0-0x79e5c5fc]
[ 0.010980] ACPI: Reserving SSDT table memory at [mem 0x79e5c600-0x79e5c77b]
[ 0.010982] ACPI: Reserving SSDT table memory at [mem 0x79e5c780-0x79e5eedf]
[ 0.010985] ACPI: Reserving UEFI table memory at [mem 0x79e5eee0-0x79e5ef21]
[ 0.010987] ACPI: Reserving WDAT table memory at [mem 0x79e5ef30-0x79e5f033]
[ 0.011026] Zone ranges:
[ 0.011028] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.011032] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.011035] Normal [mem 0x0000000100000000-0x000000017fffffff]
[ 0.011039] Movable zone start for each node
[ 0.011040] Early memory node ranges
[ 0.011041] node 0: [mem 0x0000000000001000-0x000000000003efff]
[ 0.011043] node 0: [mem 0x0000000000040000-0x000000000009efff]
[ 0.011045] node 0: [mem 0x0000000000100000-0x000000000fffffff]
[ 0.011047] node 0: [mem 0x0000000012151000-0x0000000077970fff]
[ 0.011050] node 0: [mem 0x000000007a1ab000-0x000000007a520fff]
[ 0.011052] node 0: [mem 0x000000007a54c000-0x000000007aae1fff]
[ 0.011054] node 0: [mem 0x000000007aae4000-0x000000007affffff]
[ 0.011056] node 0: [mem 0x0000000100000000-0x000000017fffffff]
[ 0.011058] Initmem setup node 0 [mem 0x0000000000001000-0x000000017fffffff]
[ 0.011066] On node 0, zone DMA: 1 pages in unavailable ranges
[ 0.011070] On node 0, zone DMA: 1 pages in unavailable ranges
[ 0.011137] On node 0, zone DMA: 97 pages in unavailable ranges
[ 0.019641] On node 0, zone DMA32: 8529 pages in unavailable ranges
[ 0.019965] On node 0, zone DMA32: 10298 pages in unavailable ranges
[ 0.019993] On node 0, zone DMA32: 43 pages in unavailable ranges
[ 0.020017] On node 0, zone DMA32: 2 pages in unavailable ranges
[ 0.029690] On node 0, zone Normal: 20480 pages in unavailable ranges
[ 0.029714] Reserving Intel graphics memory at [mem 0x7c000000-0x7fffffff]
[ 0.030062] ACPI: PM-Timer IO Port: 0x408
[ 0.030075] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1])
[ 0.030080] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1])
[ 0.030082] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1])
[ 0.030084] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1])
[ 0.030118] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-119
[ 0.030124] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.030128] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.030135] ACPI: Using ACPI (MADT) for SMP configuration information
[ 0.030137] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.030147] TSC deadline timer available
[ 0.030148] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.030194] [mem 0x80000000-0xfe041fff] available for PCI devices
[ 0.030198] Booting paravirtualized kernel on bare hardware
[ 0.030203] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffff
ffff, max_idle_ns: 19112604462750000 ns
[ 0.030216] setup_percpu: NR_CPUS:512 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ ids:1
[ 0.030945] percpu: Embedded 48 pages/cpu s158248 r8192 d30168 u524288
[ 0.030961] pcpu-alloc: s158248 r8192 d30168 u524288 alloc=1*2097152
[ 0.030968] pcpu-alloc: [0] 0 1 2 3
[ 0.031008] Kernel command line: BOOT_IMAGE=/boot/vmlinuz root=PARTUUID=e73bf b4e-27cf-383d-5de5-fbca2572be02 rootwait console=tty1 console=ttyS0,115200n8 noi nitrd
[ 0.031165] random: crng init done
[ 0.032203] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes , linear)
[ 0.032745] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.032815] Built 1 zonelists, mobility grouping on. Total pages: 993198
[ 0.032823] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.032832] software IO TLB: area num 4.
[ 0.090090] Memory: 3771368K/4036500K available (14336K kernel code, 1169K rw data, 2296K rodata, 2452K init, 2408K bss, 264876K reserved, 0K cma-reserved)
[ 0.090671] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.090821] rcu: Hierarchical RCU implementation.
[ 0.090824] rcu: RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4.
[ 0.090828] Tracing variant of Tasks RCU enabled.
[ 0.090829] rcu: RCU calculated value of scheduler-enlistment delay is 10 jif fies.
[ 0.090831] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.090849] NR_IRQS: 33024, nr_irqs: 1024, preallocated irqs: 16
[ 0.091151] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.091375] Console: colour dummy device 80x25
[ 0.091381] printk: console [tty1] enabled
[ 0.092003] printk: console [ttyS0] enabled
[ 1.470719] ACPI: Core revision 20230628
[ 1.474932] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_i dle_ns: 99544814920 ns
[ 1.484077] APIC: Switch to symmetric I/O mode setup
[ 1.490359] x2apic: IRQ remapping doesn't support X2APIC mode
[ 1.500988] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 1.554030] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x16 f8873b2b5, max_idle_ns: 440795270785 ns
[ 1.564554] Calibrating delay loop (skipped), value calculated using timer fr equency.. 3187.20 BogoMIPS (lpj=15936000)
[ 1.574627] CPU0: Thermal monitoring enabled (TM1)
[ 1.579555] Last level iTLB entries: 4KB 48, 2MB 0, 4MB 0
[ 1.584560] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0
[ 1.590484] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user poin ter sanitization
[ 1.594563] Spectre V2 : Mitigation: Retpolines
[ 1.604559] Spectre V2 : Spectre v2 / SpectreRSB: Filling RSB on context swit ch and VMEXIT
[ 1.612825] Spectre V2 : Enabling Restricted Speculation for firmware calls
[ 1.614560] Spectre V2 : mitigation: Enabling conditional Indirect Branch Pre diction Barrier
[ 1.624560] Speculative Store Bypass: Vulnerable
[ 1.629181] Register File Data Sampling: Vulnerable: No microcode
[ 1.634567] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point regi sters'
[ 1.644560] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[ 1.650913] x86/fpu: Supporting XSAVE feature 0x008: 'MPX bounds registers'
[ 1.654559] x86/fpu: Supporting XSAVE feature 0x010: 'MPX CSR'
[ 1.664560] x86/fpu: xstate_offset[3]: 576, xstate_sizes[3]: 64
[ 1.670745] x86/fpu: xstate_offset[4]: 640, xstate_sizes[4]: 64
[ 1.674559] x86/fpu: Enabled xstate features 0x1b, context size is 704 bytes, using 'compacted' format.
[ 1.721447] Freeing SMP alternatives memory: 40K
[ 1.724569] pid_max: default: 32768 minimum: 301
[ 1.737305] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, line ar)
[ 1.744582] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 1.752833] smpboot: CPU0: Intel(R) Atom(TM) Processor E3940 @ 1.60GHz (famil y: 0x6, model: 0x5c, stepping: 0x9)
[ 1.754858] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adju st=1 rcu_task_cpu_ids=4.
[ 1.764108] Performance Events: PEBS fmt3+, Goldmont events, 32-deep LBR, ful l-width counters, Intel PMU driver.
[ 1.764561] ... version: 4
[ 1.768580] ... bit width: 48
[ 1.772680] ... generic registers: 4
[ 1.774558] ... value mask: 0000ffffffffffff
[ 1.779874] ... max period: 00007fffffffffff
[ 1.784559] ... fixed-purpose events: 3
[ 1.788576] ... event mask: 000000070000000f
[ 1.794062] signal: max sigframe size: 1616
[ 1.794573] Estimated ratio of average max frequency by base frequency (times 1024): 1024
[ 1.802806] rcu: Hierarchical SRCU implementation.
[ 1.804559] rcu: Max phase no-delay instances is 1000.
[ 1.809971] smp: Bringing up secondary CPUs ...
[ 1.814713] smpboot: x86: Booting SMP configuration:
[ 1.819682] .... node #0, CPUs: #1 #2 #3
[ 1.820334] smp: Brought up 1 node, 4 CPUs
[ 1.828671] smpboot: Max logical packages: 1
[ 1.832946] smpboot: Total of 4 processors activated (12748.80 BogoMIPS)
[ 1.835189] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns
[ 1.844574] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 1.851516] pinctrl core: initialized pinctrl subsystem
[ 1.855638] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 1.862041] thermal_sys: Registered thermal governor 'step_wise'
[ 1.862044] thermal_sys: Registered thermal governor 'user_space'
[ 1.864609] cpuidle: using governor ladder
[ 1.874569] cpuidle: using governor menu
[ 1.878599] ACPI FADT declares the system doesn't support PCIe ASPM, so disab le it
[ 1.884565] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 1.891158] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xef ffffff] (base 0xe0000000)
[ 1.894591] PCI: Using configuration type 1 for base access
[ 1.900601] cryptd: max_cpu_qlen set to 1000
[ 1.904718] ACPI: Added _OSI(Module Device)
[ 1.908915] ACPI: Added _OSI(Processor Device)
[ 1.913365] ACPI: Added _OSI(Processor Aggregator Device)
[ 1.925526] ACPI: 7 ACPI AML tables successfully acquired and loaded
[ 1.936300] ACPI: _OSC evaluated successfully for all CPUs
[ 1.942185] ACPI: Interpreter enabled
[ 1.944582] ACPI: PM: (supports S0 S5)
[ 1.948341] ACPI: Using IOAPIC for interrupt routing
[ 1.953374] PCI: Using host bridge windows from ACPI; if necessary, use "pci= nocrs" and report a bug
[ 1.954562] PCI: Using E820 reservations for host bridge windows
[ 1.961073] ACPI: Enabled 11 GPEs in block 00 to 7F
[ 1.979650] ACPI: \_TZ_.FN00: New power resource
[ 1.985319] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 1.991519] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM S egments MSI HPX-Type3]
[ 1.994629] acpi PNP0A08:00: _OSC: OS requested [PME AER PCIeCapability LTR]
[ 2.001684] acpi PNP0A08:00: _OSC: platform willing to grant [PME AER PCIeCap ability LTR]
[ 2.004561] acpi PNP0A08:00: _OSC: platform retains control of PCIe features (AE_ERROR)
[ 2.013743] PCI host bridge to bus 0000:00
[ 2.014567] pci_bus 0000:00: root bus resource [io 0x0070-0x0077]
[ 2.020757] pci_bus 0000:00: root bus resource [io 0x0000-0x006f window]
[ 2.024560] pci_bus 0000:00: root bus resource [io 0x0078-0x0cf7 window]
[ 2.031347] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 2.034561] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000fffff win dow]
[ 2.042043] pci_bus 0000:00: root bus resource [mem 0x7c000001-0x7fffffff win dow]
[ 2.044564] pci_bus 0000:00: root bus resource [mem 0x7b800001-0x7bffffff win dow]
[ 2.052051] pci_bus 0000:00: root bus resource [mem 0x80000000-0xcfffffff win dow]
[ 2.054560] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff win dow]
[ 2.062042] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 2.064605] pci 0000:00:00.0: [8086:5af0] type 00 class 0x060000
[ 2.070868] pci 0000:00:02.0: [8086:5a85] type 00 class 0x030000
[ 2.074576] pci 0000:00:02.0: reg 0x10: [mem 0x90000000-0x90ffffff 64bit]
[ 2.081374] pci 0000:00:02.0: reg 0x18: [mem 0x80000000-0x8fffffff 64bit pref ]
[ 2.084566] pci 0000:00:02.0: reg 0x20: [io 0xf000-0xf03f]
[ 2.090175] pci 0000:00:02.0: BAR 2: assigned to efifb
[ 2.094563] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c00 00-0x000dffff]
[ 2.103311] pci 0000:00:0f.0: [8086:5a9a] type 00 class 0x078000
[ 2.104592] pci 0000:00:0f.0: reg 0x10: [mem 0x91819000-0x91819fff 64bit]
[ 2.111496] pci 0000:00:0f.0: PME# supported from D3hot
[ 2.114727] pci 0000:00:12.0: [8086:5ae3] type 00 class 0x010601
[ 2.120760] pci 0000:00:12.0: reg 0x10: [mem 0x91810000-0x91811fff]
[ 2.124569] pci 0000:00:12.0: reg 0x14: [mem 0x91816000-0x918160ff]
[ 2.130843] pci 0000:00:12.0: reg 0x18: [io 0xf090-0xf097]
[ 2.134570] pci 0000:00:12.0: reg 0x1c: [io 0xf080-0xf083]
[ 2.140149] pci 0000:00:12.0: reg 0x20: [io 0xf060-0xf07f]
[ 2.144568] pci 0000:00:12.0: reg 0x24: [mem 0x91815000-0x918157ff]
[ 2.150887] pci 0000:00:12.0: PME# supported from D3hot
[ 2.154701] pci 0000:00:13.0: [8086:5ad8] type 01 class 0x060400
[ 2.160810] pci 0000:00:13.0: PME# supported from D0 D3hot D3cold
[ 2.164758] pci 0000:00:13.1: [8086:5ad9] type 01 class 0x060400
[ 2.170859] pci 0000:00:13.1: PME# supported from D0 D3hot D3cold
[ 2.174749] pci 0000:00:13.2: [8086:5ada] type 01 class 0x060400
[ 2.180851] pci 0000:00:13.2: PME# supported from D0 D3hot D3cold
[ 2.184749] pci 0000:00:13.3: [8086:5adb] type 01 class 0x060400
[ 2.190852] pci 0000:00:13.3: PME# supported from D0 D3hot D3cold
[ 2.194778] pci 0000:00:15.0: [8086:5aa8] type 00 class 0x0c0330
[ 2.200815] pci 0000:00:15.0: reg 0x10: [mem 0x91800000-0x9180ffff 64bit]
[ 2.204638] pci 0000:00:15.0: PME# supported from D3hot D3cold
[ 2.210696] pci 0000:00:1a.0: [8086:5ac8] type 00 class 0x0c8000
[ 2.214580] pci 0000:00:1a.0: reg 0x10: [mem 0x91814000-0x91814fff 64bit]
[ 2.221388] pci 0000:00:1a.0: reg 0x18: [mem 0x91813000-0x91813fff 64bit]
[ 2.224632] pci 0000:00:1a.0: PME# supported from D0 D3hot
[ 2.230278] pci 0000:00:1f.0: [8086:5ae8] type 00 class 0x060100
[ 2.234833] pci 0000:00:1f.1: [8086:5ad4] type 00 class 0x0c0500
[ 2.240907] pci 0000:00:1f.1: reg 0x10: [mem 0x91812000-0x918120ff 64bit]
[ 2.244636] pci 0000:00:1f.1: reg 0x20: [io 0xf040-0xf05f]
[ 2.250483] pci 0000:01:00.0: [8086:1539] type 00 class 0x020000
[ 2.254589] pci 0000:01:00.0: reg 0x10: [mem 0x91700000-0x9171ffff]
[ 2.260889] pci 0000:01:00.0: reg 0x18: [io 0xe000-0xe01f]
[ 2.264573] pci 0000:01:00.0: reg 0x1c: [mem 0x91720000-0x91723fff]
[ 2.270997] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 2.274772] pci 0000:00:13.0: PCI bridge to [bus 01]
[ 2.279751] pci 0000:00:13.0: bridge window [io 0xe000-0xefff]
[ 2.284567] pci 0000:00:13.0: bridge window [mem 0x91700000-0x917fffff]
[ 2.291465] pci 0000:02:00.0: [8086:1539] type 00 class 0x020000
[ 2.294587] pci 0000:02:00.0: reg 0x10: [mem 0x91600000-0x9161ffff]
[ 2.300884] pci 0000:02:00.0: reg 0x18: [io 0xd000-0xd01f]
[ 2.304573] pci 0000:02:00.0: reg 0x1c: [mem 0x91620000-0x91623fff]
[ 2.310994] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 2.314772] pci 0000:00:13.1: PCI bridge to [bus 02]
[ 2.319746] pci 0000:00:13.1: bridge window [io 0xd000-0xdfff]
[ 2.324563] pci 0000:00:13.1: bridge window [mem 0x91600000-0x916fffff]
[ 2.331461] pci 0000:03:00.0: [8086:1539] type 00 class 0x020000
[ 2.334587] pci 0000:03:00.0: reg 0x10: [mem 0x91500000-0x9151ffff]
[ 2.340889] pci 0000:03:00.0: reg 0x18: [io 0xc000-0xc01f]
[ 2.344577] pci 0000:03:00.0: reg 0x1c: [mem 0x91520000-0x91523fff]
[ 2.350998] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[ 2.354774] pci 0000:00:13.2: PCI bridge to [bus 03]
[ 2.359748] pci 0000:00:13.2: bridge window [io 0xc000-0xcfff]
[ 2.364563] pci 0000:00:13.2: bridge window [mem 0x91500000-0x915fffff]
[ 2.371443] pci 0000:04:00.0: [12d8:2304] type 01 class 0x060400
[ 2.374701] pci 0000:04:00.0: supports D1 D2
[ 2.378982] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 2.384604] pci 0000:04:00.0: 4.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x1 link at 0000:00:13.3 (capable of 8.000 Gb/s with 5.0 GT/s PCIe x2 link)
[ 2.394727] pci 0000:00:13.3: PCI bridge to [bus 04-07]
[ 2.399958] pci 0000:00:13.3: bridge window [io 0xb000-0xbfff]
[ 2.404566] pci 0000:00:13.3: bridge window [mem 0x91000000-0x914fffff]
[ 2.411441] pci 0000:05:01.0: [12d8:2304] type 01 class 0x060400
[ 2.414694] pci 0000:05:01.0: supports D1 D2
[ 2.418975] pci 0000:05:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 2.424708] pci 0000:05:02.0: [12d8:2304] type 01 class 0x060400
[ 2.430860] pci 0000:05:02.0: supports D1 D2
[ 2.434560] pci 0000:05:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 2.441337] pci 0000:04:00.0: PCI bridge to [bus 05-07]
[ 2.444566] pci 0000:04:00.0: bridge window [io 0xb000-0xbfff]
[ 2.450667] pci 0000:04:00.0: bridge window [mem 0x91000000-0x914fffff]
[ 2.454653] pci 0000:06:00.0: [168c:003c] type 00 class 0x028000
[ 2.460694] pci 0000:06:00.0: reg 0x10: [mem 0x91000000-0x911fffff 64bit]
[ 2.464608] pci 0000:06:00.0: reg 0x30: [mem 0x91200000-0x9120ffff pref]
[ 2.471423] pci 0000:06:00.0: supports D1 D2
[ 2.474560] pci 0000:06:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 2.481326] pci 0000:05:01.0: PCI bridge to [bus 06]
[ 2.484569] pci 0000:05:01.0: bridge window [mem 0x91000000-0x912fffff]
[ 2.491462] pci 0000:07:00.0: [8086:1539] type 00 class 0x020000
[ 2.494593] pci 0000:07:00.0: reg 0x10: [mem 0x91400000-0x9141ffff]
[ 2.500893] pci 0000:07:00.0: reg 0x18: [io 0xb000-0xb01f]
[ 2.504576] pci 0000:07:00.0: reg 0x1c: [mem 0x91420000-0x91423fff]
[ 2.511017] pci 0000:07:00.0: PME# supported from D0 D3hot D3cold
[ 2.514745] pci 0000:05:02.0: PCI bridge to [bus 07]
[ 2.519722] pci 0000:05:02.0: bridge window [io 0xb000-0xbfff]
[ 2.524578] pci 0000:05:02.0: bridge window [mem 0x91400000-0x914fffff]
[ 2.531416] pci_bus 0000:00: on NUMA node 0
[ 2.532780] ACPI: PCI: Interrupt link LNKA configured for IRQ 15
[ 2.534563] ACPI: PCI: Interrupt link LNKA disabled
[ 2.539544] ACPI: PCI: Interrupt link LNKB configured for IRQ 15
[ 2.544560] ACPI: PCI: Interrupt link LNKB disabled
[ 2.549541] ACPI: PCI: Interrupt link LNKC configured for IRQ 15
[ 2.554560] ACPI: PCI: Interrupt link LNKC disabled
[ 2.559540] ACPI: PCI: Interrupt link LNKD configured for IRQ 15
[ 2.564560] ACPI: PCI: Interrupt link LNKD disabled
[ 2.569549] ACPI: PCI: Interrupt link LNKE configured for IRQ 15
[ 2.574560] ACPI: PCI: Interrupt link LNKE disabled
[ 2.579535] ACPI: PCI: Interrupt link LNKF configured for IRQ 15
[ 2.584564] ACPI: PCI: Interrupt link LNKF disabled
[ 2.589542] ACPI: PCI: Interrupt link LNKG configured for IRQ 15
[ 2.594560] ACPI: PCI: Interrupt link LNKG disabled
[ 2.599539] ACPI: PCI: Interrupt link LNKH configured for IRQ 15
[ 2.604566] ACPI: PCI: Interrupt link LNKH disabled
[ 2.613293] iommu: Default domain type: Translated
[ 2.614573] iommu: DMA domain TLB invalidation policy: lazy mode
[ 2.620765] SCSI subsystem initialized
[ 2.624621] libata version 3.00 loaded.
[ 2.624667] ACPI: bus type USB registered
[ 2.628718] usbcore: registered new interface driver usbfs
[ 2.634228] usbcore: registered new interface driver hub
[ 2.634583] usbcore: registered new device driver usb
[ 2.639673] pps_core: LinuxPPS API ver. 1 registered
[ 2.644568] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti <giometti@linux.it>
[ 2.653707] PTP clock support registered
[ 2.654713] efivars: Registered efivars operations
[ 2.659778] PCI: Using ACPI for IRQ routing
[ 2.692008] PCI: pci_cache_line_size set to 64 bytes
[ 2.692116] e820: reserve RAM buffer [mem 0x0003f000-0x0003ffff]
[ 2.692121] e820: reserve RAM buffer [mem 0x0009f000-0x0009ffff]
[ 2.692124] e820: reserve RAM buffer [mem 0x71603018-0x73ffffff]
[ 2.692127] e820: reserve RAM buffer [mem 0x71613018-0x73ffffff]
[ 2.692129] e820: reserve RAM buffer [mem 0x7699a000-0x77ffffff]
[ 2.692132] e820: reserve RAM buffer [mem 0x77971000-0x77ffffff]
[ 2.692134] e820: reserve RAM buffer [mem 0x7a521000-0x7bffffff]
[ 2.692138] e820: reserve RAM buffer [mem 0x7aae2000-0x7bffffff]
[ 2.692141] e820: reserve RAM buffer [mem 0x7b000000-0x7bffffff]
[ 2.692238] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 2.694565] hpet0: 8 comparators, 64-bit 19.200000 MHz counter
[ 2.702484] clocksource: Switched to clocksource tsc-early
[ 2.704553] pnp: PnP ACPI init
[ 2.704553] system 00:00: [io 0x0a00-0x0a0f] has been reserved
[ 2.709740] system 00:00: [io 0x0a10-0x0a1f] has been reserved
[ 2.715682] system 00:00: [io 0x0a20-0x0a2f] has been reserved
[ 2.721611] system 00:00: [io 0x0a30-0x0a3f] has been reserved
[ 2.728037] pnp 00:01: [dma 0 disabled]
[ 2.728231] system 00:02: [io 0x0680-0x069f] has been reserved
[ 2.734163] system 00:02: [io 0x0400-0x047f] has been reserved
[ 2.740092] system 00:02: [io 0x0500-0x05fe] has been reserved
[ 2.746032] system 00:02: [io 0x0600-0x061f] has been reserved
[ 2.751954] system 00:02: [io 0x164e-0x164f] has been reserved
[ 2.758497] system 00:03: [mem 0xe0000000-0xefffffff] has been reserved
[ 2.765136] system 00:03: [mem 0xfea00000-0xfeafffff] has been reserved
[ 2.771751] system 00:03: [mem 0xfed01000-0xfed01fff] has been reserved
[ 2.778382] system 00:03: [mem 0xfed03000-0xfed03fff] has been reserved
[ 2.785011] system 00:03: [mem 0xfed06000-0xfed06fff] has been reserved
[ 2.791634] system 00:03: [mem 0xfed08000-0xfed09fff] has been reserved
[ 2.798261] system 00:03: [mem 0xfed80000-0xfedbffff] has been reserved
[ 2.804892] system 00:03: [mem 0xfed1c000-0xfed1cfff] has been reserved
[ 2.811516] system 00:03: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 2.818956] pnp: PnP ACPI: found 5 devices
[ 2.829029] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff,
le_ns: 2085701024 ns
[ 2.837988] NET: Registered PF_INET protocol family
[ 2.843028] IP idents hash table entries: 65536 (order: 7, 524288 bytes, line ar)
[ 2.852576] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 3276 8 bytes, linear)
[ 2.861133] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 2.868896] TCP established hash table entries: 32768 (order: 6, 262144 bytes , linear)
[ 2.876977] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, line ar)
[ 2.884860] TCP: Hash tables configured (established 32768 bind 32768)
[ 2.891573] MPTCP token hash table entries: 4096 (order: 5, 98304 bytes, line ar)
[ 2.899051] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 2.905813] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 2.913065] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 2.918784] pci 0000:00:13.0: PCI bridge to [bus 01]
[ 2.923769] pci 0000:00:13.0: bridge window [io 0xe000-0xefff]
[ 2.929872] pci 0000:00:13.0: bridge window [mem 0x91700000-0x917fffff]
[ 2.936677] pci 0000:00:13.1: PCI bridge to [bus 02]
[ 2.941646] pci 0000:00:13.1: bridge window [io 0xd000-0xdfff]
[ 2.947767] pci 0000:00:13.1: bridge window [mem 0x91600000-0x916fffff]
[ 2.954576] pci 0000:00:13.2: PCI bridge to [bus 03]
[ 2.959550] pci 0000:00:13.2: bridge window [io 0xc000-0xcfff]
[ 2.965656] pci 0000:00:13.2: bridge window [mem 0x91500000-0x915fffff]
[ 2.972454] pci 0000:05:01.0: PCI bridge to [bus 06]
[ 2.977437] pci 0000:05:01.0: bridge window [mem 0x91000000-0x912fffff]
[ 2.984242] pci 0000:05:02.0: PCI bridge to [bus 07]
[ 2.989221] pci 0000:05:02.0: bridge window [io 0xb000-0xbfff]
[ 2.995330] pci 0000:05:02.0: bridge window [mem 0x91400000-0x914fffff]
[ 3.002128] pci 0000:04:00.0: PCI bridge to [bus 05-07]
[ 3.007369] pci 0000:04:00.0: bridge window [io 0xb000-0xbfff]
[ 3.013478] pci 0000:04:00.0: bridge window [mem 0x91000000-0x914fffff]
[ 3.020280] pci 0000:00:13.3: PCI bridge to [bus 04-07]
[ 3.025524] pci 0000:00:13.3: bridge window [io 0xb000-0xbfff]
[ 3.031625] pci 0000:00:13.3: bridge window [mem 0x91000000-0x914fffff]
[ 3.038432] pci_bus 0000:00: resource 4 [io 0x0070-0x0077]
[ 3.044016] pci_bus 0000:00: resource 5 [io 0x0000-0x006f window]
[ 3.050204] pci_bus 0000:00: resource 6 [io 0x0078-0x0cf7 window]
[ 3.056393] pci_bus 0000:00: resource 7 [io 0x0d00-0xffff window]
[ 3.062581] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000fffff window]
[ 3.069467] pci_bus 0000:00: resource 9 [mem 0x7c000001-0x7fffffff window]
[ 3.076355] pci_bus 0000:00: resource 10 [mem 0x7b800001-0x7bffffff window]
[ 3.083328] pci_bus 0000:00: resource 11 [mem 0x80000000-0xcfffffff window]
[ 3.090297] pci_bus 0000:00: resource 12 [mem 0xe0000000-0xefffffff window]
[ 3.097266] pci_bus 0000:01: resource 0 [io 0xe000-0xefff]
[ 3.102838] pci_bus 0000:01: resource 1 [mem 0x91700000-0x917fffff]
[ 3.109113] pci_bus 0000:02: resource 0 [io 0xd000-0xdfff]
[ 3.114694] pci_bus 0000:02: resource 1 [mem 0x91600000-0x916fffff]
[ 3.120963] pci_bus 0000:03: resource 0 [io 0xc000-0xcfff]
[ 3.126552] pci_bus 0000:03: resource 1 [mem 0x91500000-0x915fffff]
[ 3.132828] pci_bus 0000:04: resource 0 [io 0xb000-0xbfff]
[ 3.138417] pci_bus 0000:04: resource 1 [mem 0x91000000-0x914fffff]
[ 3.144697] pci_bus 0000:05: resource 0 [io 0xb000-0xbfff]
[ 3.150275] pci_bus 0000:05: resource 1 [mem 0x91000000-0x914fffff]
[ 3.156553] pci_bus 0000:06: resource 1 [mem 0x91000000-0x912fffff]
[ 3.162822] pci_bus 0000:07: resource 0 [io 0xb000-0xbfff]
[ 3.168409] pci_bus 0000:07: resource 1 [mem 0x91400000-0x914fffff]
[ 3.175479] PCI: CLS 0 bytes, default 64
[ 3.179501] pci 0000:00:0d.0: [8086:5a92] type 00 class 0x058000
[ 3.185591] pci 0000:00:0d.0: reg 0x10: [mem 0xd0000000-0xd0ffffff 64bit]
[ 3.192924] pci 0000:00:0d.2: [8086:5a96] type 00 class 0x0c8000
[ 3.198972] pci 0000:00:0d.2: reg 0x10: [mem 0xfed01000-0xfed01fff]
[ 3.205453] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 3.211897] software IO TLB: mapped [mem 0x000000006d603000-0x000000007160300 0] (64MB)
[ 3.219996] RAPL PMU: API unit is 2^-32 Joules, 4 fixed counters, 655360 ms o vfl timer
[ 3.227928] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
[ 3.233707] RAPL PMU: hw unit of domain package 2^-14 Joules
[ 3.239369] RAPL PMU: hw unit of domain dram 2^-14 Joules
[ 3.244782] RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules
[ 3.250572] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x16f8873b 2b5, max_idle_ns: 440795270785 ns
[ 3.260616] clocksource: Switched to clocksource tsc
[ 3.267034] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[ 3.273796] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 3.279853] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 47)
[ 3.289473] hv_vmbus: registering driver hyperv_fb
[ 3.294578] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:0 0/input/input0
[ 3.303110] ACPI: button: Power Button [PWRB]
[ 3.307567] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/inp ut1
[ 3.315074] ACPI: button: Power Button [PWRF]
[ 3.321570] thermal LNXTHERM:00: registered as thermal_zone0
[ 3.327272] ACPI: thermal: Thermal Zone [TZ01] (32 C)
[ 3.332553] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 3.359866] 00:01: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 1655 0A
[ 3.369123] Non-volatile memory driver v1.3
[ 3.373440] Linux agpgart interface v0.103
[ 3.377583] AMD-Vi: AMD IOMMUv2 functionality not available on this system - This is not a bug.
[ 3.386334] ACPI: bus type drm_connector registered
[ 3.393282] loop: module loaded
[ 3.396520] Guest personality initialized and is inactive
[ 3.401956] VMCI host device registered (name=vmci, major=10, minor=256)
[ 3.408681] Initialized host personality
[ 3.412674] lpc_ich 0000:00:1f.0: I/O space for ACPI uninitialized
[ 3.419139] VMware PVSCSI driver - version 1.0.7.0-k
[ 3.424165] hv_vmbus: registering driver hv_storvsc
[ 3.429864] ahci 0000:00:12.0: version 3.0
[ 3.440316] ahci 0000:00:12.0: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 imp l SATA mode
[ 3.448463] ahci 0000:00:12.0: flags: 64bit ncq sntf pm clo only pmp pio slum part deso sadm sds apst
[ 3.458320] scsi host0: ahci
[ 3.461486] scsi host1: ahci
[ 3.464491] ata1: SATA max UDMA/133 abar m2048@0x91815000 port 0x91815100 irq 126
[ 3.471977] ata2: SATA max UDMA/133 abar m2048@0x91815000 port 0x91815180 irq 126
[ 3.479957] VMware vmxnet3 virtual NIC driver - version 1.7.0.0-k-NAPI
[ 3.486545] hv_vmbus: registering driver hv_netvsc
[ 3.491349] Fusion MPT base driver 3.04.20
[ 3.495461] Copyright (c) 1999-2008 LSI Corporation
[ 3.500347] Fusion MPT SPI Host driver 3.04.20
[ 3.504831] Fusion MPT SAS Host driver 3.04.20
[ 3.509755] xhci_hcd 0000:00:15.0: xHCI Host Controller
[ 3.515021] xhci_hcd 0000:00:15.0: new USB bus registered, assigned bus numbe r 1
[ 3.523525] xhci_hcd 0000:00:15.0: hcc params 0x200077c1 hci version 0x100 qu irks 0x0000000081109810
[ 3.533052] xhci_hcd 0000:00:15.0: xHCI Host Controller
[ 3.538297] xhci_hcd 0000:00:15.0: new USB bus registered, assigned bus numbe r 2
[ 3.545708] xhci_hcd 0000:00:15.0: Host supports USB 3.0 SuperSpeed
[ 3.552369] hub 1-0:1.0: USB hub found
[ 3.556179] hub 1-0:1.0: 8 ports detected
[ 3.561945] hub 2-0:1.0: USB hub found
[ 3.565769] hub 2-0:1.0: 7 ports detected
[ 3.571210] usbcore: registered new interface driver usb-storage
[ 3.577323] i8042: PNP: No PS/2 controller found.
[ 3.582036] i8042: Probing ports directly.
[ 3.587166] i8042: No controller found
[ 3.590926] hv_vmbus: registering driver hyperv_keyboard
[ 3.596316] rtc_cmos 00:04: RTC can wake from S4
[ 3.601844] rtc_cmos 00:04: registered as rtc0
[ 3.606458] rtc_cmos 00:04: setting system clock to 2026-01-27T21:51:05 UTC ( 1769550665)
[ 3.614587] rtc_cmos 00:04: alarms up to one month, y3k, 242 bytes nvram
[ 3.622191] intel_pstate: Intel P-state driver initializing
[ 3.628061] sdhci: Secure Digital Host Controller Interface driver
[ 3.634258] sdhci: Copyright(c) Pierre Ossman
[ 3.639128] efifb: probing for efifb
[ 3.642741] efifb: framebuffer at 0x80000000, using 1876k, total 1875k
[ 3.649294] efifb: mode is 800x600x32, linelength=3200, pages=1
[ 3.655232] efifb: scrolling: redraw
[ 3.658811] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 3.665392] Console: switching to colour frame buffer device 100x37
[ 3.672892] fb0: EFI VGA frame buffer device
[ 3.677296] hid: raw HID events driver (C) Jiri Kosina
[ 3.682531] hv_vmbus: registering driver hid_hyperv
[ 3.687507] usbcore: registered new interface driver usbhid
[ 3.693111] usbhid: USB HID core driver
[ 3.697064] hv_utils: Registering HyperV Utility Driver
[ 3.702316] hv_vmbus: registering driver hv_utils
[ 3.707054] hv_vmbus: registering driver hv_balloon
[ 3.712164] NET: Registered PF_INET6 protocol family
[ 3.717650] Segment Routing with IPv6
[ 3.721366] In-situ OAM (IOAM) with IPv6
[ 3.725367] NET: Registered PF_PACKET protocol family
[ 3.731112] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 3.745505] 8021q: 802.1Q VLAN Support v1.8
[ 3.750474] NET: Registered PF_VSOCK protocol family
[ 3.756814] microcode: Current revision: 0x0000002e
[ 3.762642] microcode: Microcode Update Driver: v2.2.
[ 3.762652] IPI shorthand broadcast: enabled
[ 3.773406] SSE version of gcm_enc/dec engaged.
[ 3.782865] sched_clock: Marking stable (2380125129, 1393257606)->(4010658398 , -237275663)
[ 3.794647] clk: Disabling unused clocks
[ 3.804480] ata2: SATA link down (SStatus 4 SControl 300)
[ 3.810638] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 3.817729] ata1.00: ATA-9: ADATA_IM2S3134N-064GM, 6.8E, max UDMA/133
[ 3.824943] ata1.00: 125045424 sectors, multi 16: LBA48 NCQ (depth 32), AA
[ 3.832692] ata1.00: configured for UDMA/133
[ 3.837959] scsi 0:0:0:0: Direct-Access ATA ADATA_IM2S3134N- 6.8E PQ : 0 ANSI: 5
[ 3.847523] sd 0:0:0:0: [sda] 125045424 512-byte logical blocks: (64.0 GB/59. 6 GiB)
[ 3.855992] sd 0:0:0:0: [sda] Write Protect is off
[ 3.861527] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.861592] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, does n't support DPO or FUA
[ 3.872235] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[ 3.880789] GPT:Primary header thinks Alt. header is not at the end of the di sk.
[ 3.888976] GPT:246304 != 125045423
[ 3.893237] GPT:Alternate GPT header not at the end of the disk.
[ 3.900063] GPT:246304 != 125045423
[ 3.904335] GPT: Use GNU Parted to correct GPT errors.
[ 3.910256] sda: sda1 sda2 sda128
[ 3.914619] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.925968] EXT4-fs (sda2): mounted filesystem ff313567-e9f1-5a5d-9895-3ba130 b4a864 ro with ordered data mode. Quota mode: disabled.
[ 3.939527] VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
[ 3.948208] Freeing unused kernel image (initmem) memory: 2452K
[ 3.955015] Write protecting the kernel read-only data: 18432k
[ 3.962547] Freeing unused kernel image (rodata/data gap) memory: 1800K
[ 3.970058] Run /sbin/init as init process
[ 3.975022] with arguments:
[ 3.975024] /sbin/init
[ 3.975026] with environment:
[ 3.975027] HOME=/
[ 3.975029] TERM=linux
[ 4.039287] init: Console is alive
[ 4.047493] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.061238] button_hotplug: loading out-of-tree module taints kernel.
[ 4.068727] Button Hotplug driver version 0.4.1
[ 4.077345] Intel(R) 2.5G Ethernet Linux Driver
[ 4.082740] Copyright(c) 2018 Intel Corporation.
[ 4.090574] igb: Intel(R) Gigabit Ethernet Network Driver
[ 4.096910] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 4.136409] igb 0000:01:00.0: added PHC on eth0
[ 4.141831] igb 0000:01:00.0: Intel(R) Gigabit Ethernet Network Connection
[ 4.149573] igb 0000:01:00.0: eth0: (PCIe:2.5Gb/s:Width x1) 7c:5a:1c:6d:05:b3
[ 4.157555] igb 0000:01:00.0: eth0: PBA No: FFFFFF-0FF
[ 4.163532] igb 0000:01:00.0: Using MSI-X interrupts. 2 rx queue(s), 2 tx que ue(s)
[ 4.203991] igb 0000:02:00.0: added PHC on eth1
[ 4.209402] igb 0000:02:00.0: Intel(R) Gigabit Ethernet Network Connection
[ 4.217138] igb 0000:02:00.0: eth1: (PCIe:2.5Gb/s:Width x1) 7c:5a:1c:6d:05:b0
[ 4.225123] igb 0000:02:00.0: eth1: PBA No: FFFFFF-0FF
[ 4.231083] igb 0000:02:00.0: Using MSI-X interrupts. 2 rx queue(s), 2 tx que ue(s)
[ 4.272524] igb 0000:03:00.0: added PHC on eth2
[ 4.277924] igb 0000:03:00.0: Intel(R) Gigabit Ethernet Network Connection
[ 4.285627] igb 0000:03:00.0: eth2: (PCIe:2.5Gb/s:Width x1) 7c:5a:1c:6d:05:b1
[ 4.293568] igb 0000:03:00.0: eth2: PBA No: FFFFFF-0FF
[ 4.299492] igb 0000:03:00.0: Using MSI-X interrupts. 2 rx queue(s), 2 tx que ue(s)
[ 4.341317] igb 0000:07:00.0: added PHC on eth3
[ 4.346686] igb 0000:07:00.0: Intel(R) Gigabit Ethernet Network Connection
[ 4.354348] igb 0000:07:00.0: eth3: (PCIe:2.5Gb/s:Width x1) 7c:5a:1c:6d:05:b2
[ 4.362256] igb 0000:07:00.0: eth3: PBA No: FFFFFF-0FF
[ 4.368182] igb 0000:07:00.0: Using MSI-X interrupts. 2 rx queue(s), 2 tx que ue(s)
[ 4.378613] kmodloader: done loading kernel modules from /etc/modules-boot.d/ *
[ 4.396095] init: - preinit -
[ 4.514864] 8021q: adding VLAN 0 to HW filter on device eth0
[ 8.575364] mount_root: mounting /dev/root with options
[ 8.654357] EXT4-fs (sda2): re-mounted ff313567-e9f1-5a5d-9895-3ba130b4a864 r /w.
[ 8.755403] FAT-fs (sda1): Volume was not properly unmounted. Some data may b e corrupt. Please run fsck.
[ 8.768579] urandom-seed: Seeding with /etc/urandom.seed
[ 8.813080] procd: - early -
[ 9.340694] procd: - ubus -
[ 9.496429] procd: - init -
[ 9.620349] kmodloader: loading kernel modules from /etc/modules.d/*
[ 9.636304] e1000: Intel(R) PRO/1000 Network Driver
[ 9.641997] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 9.651651] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver
[ 9.658586] ixgbe: Copyright (c) 1999-2016 Intel Corporation.
[ 9.670021] i2c_dev: i2c /dev entries driver
[ 9.686193] e1000e: Intel(R) PRO/1000 Network Driver
[ 9.691966] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 9.717235] PPP generic driver version 2.4.2
[ 9.722768] NET: Registered PF_PPPOX protocol family
[ 9.724447] urngd: v1.0.2 started.
[ 9.761976] Console: switching to colour dummy device 80x25
[ 9.769111] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/bxt_d mc_ver1_07.bin (v1.7)
[ 10.186780] i915 0000:00:02.0: [drm] [ENCODER:110:DDI A/PHY A] failed to retr ieve link info, disabling eDP
[ 10.200194] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
[ 10.209097] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 10.217043] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/L NXVIDEO:00/input/input2
[ 10.229271] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
[ 10.238270] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 10.238454] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
[ 10.253932] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
[ 11.254157] 8021q: adding VLAN 0 to HW filter on device eth0
[ 11.260209] br-lan: port 1(eth0) entered blocking state
[ 11.265502] br-lan: port 1(eth0) entered disabled state
[ 11.270759] igb 0000:01:00.0 eth0: entered allmulticast mode
[ 11.276546] igb 0000:01:00.0 eth0: entered promiscuous mode
[ 11.344647] 8021q: adding VLAN 0 to HW filter on device eth1
Now retry all ports.
1 Like
Port 1 lights up!
root@OpenWrt:~# logread -f
Tue Jan 27 17:12:25 2026 daemon.warn odhcpd[2046]: No default route present, setting ra_lifetime to 0!
Tue Jan 27 17:12:41 2026 daemon.warn odhcpd[2046]: No default route present, setting ra_lifetime to 0!
Tue Jan 27 17:12:57 2026 daemon.warn odhcpd[2046]: No default route present, setting ra_lifetime to 0!