Asus ax4200 Problem installing openwrt, the whole router freezes and you can't do anything

Good morning, I have a problem with Asus ax4200. When installing the OpenWrt software according to the instructions Remittor. I upload 1 sys file, after restarting the router, openwrt and luci appear, a message appears at the top that the software is temporary, upload sysupgrade, after uploading the file according to the instructions. The router starts up, logs in to Luci, but it looks like it's some old overlay or something similar. For the first 5 seconds I can switch between tabs, but after that time the router seems to hang and there is no response. In the first tab, the system info shows "no communicate\ no more info" info, this is the place where the cpu model should appear, info about the system and device, but nothing is displayed there. Once the router stops responding, you cannot call it back through the browser or access the admin profile. Even if I somehow managed to install it correctly, I had no access to the wireless network cards. I couldn't make any changes, add networks or anything else. The situation occurred when I accidentally wanted to reinstall the system and at the time of uploading the update I uploaded the kernel file. I can return to the Asus system using recovery and it works properly (it is also interesting that when returning to the Asus system, it remembers all the settings of wifi, network, local settings, etc., but there is a problem with reloading openwrt.

After installing the software from the Link, openwrt starts and shows the information, it seems correct, but I don't have access to the network cards. Restarting the device does nothing.

TUF-AX4200 bootloader version: 1.0.0.3
MAC Address: 00:AA:BB:CC:DD:E0
Read 40 bytes from volume linux to 0000000046000000
   FIT/FDT format image found at 0x46000000,size 0x39ed08
Read 3796272 bytes from volume linux to 0000000046000000
## Loading kernel from FIT Image at 46000000 ...
   Using 'config-1' configuration
   Trying 'kernel-1' kernel subimage
     Description:  ARM64 OpenWrt Linux-5.15.150
     Type:         Kernel Image
     Compression:  lzma compressed
     Data Start:   0x460000ec
     Data Size:    3773680 Bytes = 3.6 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x48000000
     Entry Point:  0x48000000
     Hash algo:    crc32
     Hash value:   1087e554
     Hash algo:    sha1
     Hash value:   7d68057efa1fa82242033ff4e9969456b4f6d754
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 46000000 ...
   Using 'config-1' configuration
   Trying 'fdt-1' fdt subimage
     Description:  ARM64 OpenWrt asus_tuf-ax4200 device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x4639971c
     Data Size:    20670 Bytes = 20.2 KiB
     Architecture: AArch64
     Load Address: 0x47000000
     Hash algo:    crc32
     Hash value:   78e5c981
     Hash algo:    sha1
     Hash value:   24aff548f48de6099175d5718ea4bbdc4fa384c3
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Loading fdt from 0x4639971c to 0x47000000
   Booting using the fdt blob at 0x47000000
Read 40 bytes from volume linux2 to 000000005f7ffb90
   Uncompressing Kernel Image
   Loading Device Tree to 000000005f7f3000, end 000000005f7fb0bd ... OK
volume linux seq: 4

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 5.15.150 (builder@buildhost)
(aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r23809-234f1a2efa)
12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Fri Mar 22 22:09:42 2024
[    0.000000] Machine model: ASUS TUF-AX4200
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x0000000042ffffff]
[    0.000000]   node   0: [mem 0x0000000043000000-0x000000004302ffff]
[    0.000000]   node   0: [mem 0x0000000043030000-0x000000004fbfffff]
[    0.000000]   node   0: [mem 0x000000004fc00000-0x000000004ffbffff]
[    0.000000]   node   0: [mem 0x000000004ffc0000-0x000000005fffffff]
[    0.000000] Initmem setup node 0 [mem
0x0000000040000000-0x000000005fffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.2
[    0.000000] percpu: Embedded 18 pages/cpu s33112 r8192 d32424 u73728
[    0.000000] pcpu-alloc: s33112 r8192 d32424 u73728 alloc=18*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: GIC system register CPU interface
[    0.000000] CPU features: kernel page table isolation disabled by
kernel configuration
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129024
[    0.000000] Kernel command line: ubi.mtd=UBI_DEV
[    0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288
bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144
bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 498136K/524288K available (8384K kernel code,
906K rwdata, 1472K rodata, 448K init, 300K bss, 26152K reserved, 0K
cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay
is 10 jiffies.
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[    0.000000] GICv3: 640 SPIs implemented
[    0.000000] GICv3: 0 Extended SPIs implemented
[    0.000000] GICv3: Distributor has no Range Selector support
[    0.000000] Root IRQ handler: 0xffffffc008010090
[    0.000000] GICv3: 16 PPIs implemented
[    0.000000] GICv3: CPU0: found redistributor 0 region
0:0x000000000c080000
[    0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff
max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
[    0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps
every 4398046511101ns
[    0.000106] Calibrating delay loop (skipped), value calculated using
timer frequency.. 26.00 BogoMIPS (lpj=130000)
[    0.000114] pid_max: default: 32768 minimum: 301
[    0.000310] Mount-cache hash table entries: 1024 (order: 1, 8192
bytes, linear)
[    0.000319] Mountpoint-cache hash table entries: 1024 (order: 1, 8192
bytes, linear)
[    0.001337] rcu: Hierarchical SRCU implementation.
[    0.001607] smp: Bringing up secondary CPUs ...
[    0.001869] Detected VIPT I-cache on CPU1
[    0.001890] GICv3: CPU1: found redistributor 1 region
0:0x000000000c0a0000
[    0.001916] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.002174] Detected VIPT I-cache on CPU2
[    0.002185] GICv3: CPU2: found redistributor 2 region
0:0x000000000c0c0000
[    0.002195] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.002433] Detected VIPT I-cache on CPU3
[    0.002443] GICv3: CPU3: found redistributor 3 region
0:0x000000000c0e0000
[    0.002452] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.002478] smp: Brought up 1 node, 4 CPUs
[    0.002492] SMP: Total of 4 processors activated.
[    0.002495] CPU features: detected: 32-bit EL0 Support
[    0.002499] CPU features: detected: CRC32 instructions
[    0.002523] CPU features: emulated: Privileged Access Never (PAN)
using TTBR0_EL1 switching
[    0.002575] CPU: All CPU(s) started at EL2
[    0.002585] alternatives: patching kernel code
[    0.004954] clocksource: jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.004973] futex hash table entries: 1024 (order: 4, 65536 bytes,
linear)
[    0.005115] pinctrl core: initialized pinctrl subsystem
[    0.005750] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.005976] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic
allocations
[    0.006002] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for
atomic allocations
[    0.006020] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for
atomic allocations
[    0.006263] thermal_sys: Registered thermal governor 'fair_share'
[    0.006266] thermal_sys: Registered thermal governor 'bang_bang'
[    0.006270] thermal_sys: Registered thermal governor 'step_wise'
[    0.006273] thermal_sys: Registered thermal governor 'user_space'
[    0.006428] ASID allocator initialised with 65536 entries
[    0.006751] pstore: Registered ramoops as persistent store backend
[    0.006755] ramoops: using 0x10000@0x42ff0000, ecc: 0
[    0.014470] cryptd: max_cpu_qlen set to 1000
[    0.016234] SCSI subsystem initialized
[    0.016321] libata version 3.00 loaded.
[    0.017099] clocksource: Switched to clocksource arch_sys_counter
[    0.017519] NET: Registered PF_INET protocol family
[    0.017602] IP idents hash table entries: 8192 (order: 4, 65536
bytes, linear)
[    0.017956] tcp_listen_portaddr_hash hash table entries: 256 (order:
0, 4096 bytes, linear)
[    0.017967] Table-perturb hash table entries: 65536 (order: 6, 262144
bytes, linear)
[    0.017973] TCP established hash table entries: 4096 (order: 3, 32768
bytes, linear)
[    0.017993] TCP bind hash table entries: 4096 (order: 4, 65536 bytes,
linear)
[    0.018036] TCP: Hash tables configured (established 4096 bind 4096)
[    0.018097] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.018109] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes,
linear)
[    0.018215] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.018233] PCI: CLS 0 bytes, default 64
[    0.019956] workingset: timestamp_bits=46 max_order=17 bucket_order=0
[    0.022546] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.022560] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.044623] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 251)
[    0.048052] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.049376] printk: console [ttyS0] disabled
[    0.069514] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 121,
base_baud = 2500000) is a ST16650V2
[    0.709760] printk: console [ttyS0] enabled
[    0.714598] mtk_rng 1020f000.rng: registered RNG driver
[    0.714655] hwrng: no data available
[    0.720031] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    0.731643] loop: module loaded
[    0.734792] Loading iSCSI transport class v2.0-870.
[    0.740981] spi spi0.0: setup: ignoring unsupported mode bits a00
[    0.747325] spi-nand spi0.0: Winbond SPI NAND was found.
[    0.752620] spi-nand spi0.0: 256 MiB, block size: 128 KiB, page size:
2048, OOB size: 128
[    0.760935] 2 fixed-partitions partitions found on MTD device spi0.0
[    0.767277] Creating 2 MTD partitions on "spi0.0":
[    0.772051] 0x000000000000-0x000000400000 : "Bootloader"
[    0.781772] 0x000000400000-0x000010000000 : "UBI_DEV"
[    1.178286] mtk_soc_eth 15100000.ethernet: generated random MAC
address f6:e5:11:01:ba:4a
[    1.186507] mtk_soc_eth 15100000.ethernet: generated random MAC
address 0a:c5:0c:16:e1:e2
[    1.256080] Maxlinear Ethernet GPY211C mdio-bus:06: Firmware Version:
0x886F (release)
[    1.266195] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine
at 0xffffffc009600000, irq 129
[    1.276016] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine
at 0xffffffc009600000, irq 129
[    1.285519] i2c_dev: i2c /dev entries driver
[    1.290760] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31
sec, nowayout=0)
[    1.299206] NET: Registered PF_INET6 protocol family
[    1.304740] Segment Routing with IPv6
[    1.308420] In-situ OAM (IOAM) with IPv6
[    1.312354] NET: Registered PF_PACKET protocol family
[    1.317419] bridge: filtering via arp/ip/ip6tables is no longer
available by default. Update your scripts to load br_netfilter if you
need this.
[    1.330464] 8021q: 802.1Q VLAN Support v1.8
[    1.335632] pstore: Using crash dump compression: deflate
[    1.378739] mt7530-mdio mdio-bus:1f: no interrupt support
[    1.390209] mt7530-mdio mdio-bus:1f: configuring for fixed/2500base-x
link mode
[    1.399334] mt7530-mdio mdio-bus:1f: Link is Up - 2.5Gbps/Full - flow
control rx/tx
[    1.408271] MediaTek MT7531 PHY mt7530-0:01: Configure LED registers
(num=14)
[    1.422794] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY
[mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=POLL)
[    1.442819] MediaTek MT7531 PHY mt7530-0:02: Configure LED registers
(num=14)
[    1.457352] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY
[mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=POLL)
[    1.477072] MediaTek MT7531 PHY mt7530-0:03: Configure LED registers
(num=14)
[    1.491608] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY
[mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=POLL)
[    1.511328] MediaTek MT7531 PHY mt7530-0:04: Configure LED registers
(num=14)
[    1.525857] mt7530-mdio mdio-bus:1f lan4 (uninitialized): PHY
[mt7530-0:04] driver [MediaTek MT7531 PHY] (irq=POLL)
[    1.536920] DSA: tree 0 setup
[    1.540166] ubi0: default fastmap pool size: 100
[    1.544773] ubi0: default fastmap WL pool size: 50
[    1.549577] ubi0: attaching mtd1
[    3.737100] random: crng init done
[    5.670318] ubi0: scanning is finished
[    5.697899] ubi0: attached mtd1 (name "UBI_DEV", size 252 MiB)
[    5.703727] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976
bytes
[    5.710589] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    5.717359] ubi0: VID header offset: 2048 (aligned 2048), data
offset: 4096
[    5.724298] ubi0: good PEBs: 2016, bad PEBs: 0, corrupted PEBs: 0
[    5.730372] ubi0: user volume: 8, internal volumes: 1, max. volumes
count: 128
[    5.737573] ubi0: max/mean erase counter: 148/82, WL threshold: 4096,
image sequence number: 729974110
[    5.746852] ubi0: available PEBs: 0, total reserved PEBs: 2016, PEBs
reserved for bad PEB handling: 40
[    5.756140] ubi0: background thread "ubi_bgt0d" started, PID 455
[    5.759817] block ubiblock0_6: created from ubi0:6(rootfs)
[    5.767604] ubiblock: device ubiblock0_6 (rootfs) set to be root
filesystem
[    5.790496] VFS: Mounted root (squashfs filesystem) readonly on
device 254:0.
[    5.797816] Freeing unused kernel memory: 448K
[    5.857131] Run /sbin/init as init process
[    5.861211]   with arguments:
[    5.864162]     /sbin/init
[    5.866852]   with environment:
[    5.869982]     HOME=/
[    5.872326]     TERM=linux
[    6.201561] init: Console is alive
[    6.205043] init: - watchdog -
[    6.901600] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    6.943737] usbcore: registered new interface driver usbfs
[    6.949260] usbcore: registered new interface driver hub
[    6.954584] usbcore: registered new device driver usb
[    6.963834] xhci-mtk 11200000.usb: xHCI Host Controller
[    6.969078] xhci-mtk 11200000.usb: new USB bus registered, assigned
bus number 1
[    6.979520] xhci-mtk 11200000.usb: hcc params 0x01403f99 hci version
0x110 quirks 0x0000000000210010
[    6.988677] xhci-mtk 11200000.usb: irq 123, io mem 0x11200000
[    6.994496] xhci-mtk 11200000.usb: xHCI Host Controller
[    6.999715] xhci-mtk 11200000.usb: new USB bus registered, assigned
bus number 2
[    7.007098] xhci-mtk 11200000.usb: Host supports USB 3.2 Enhanced
SuperSpeed
[    7.014481] hub 1-0:1.0: USB hub found
[    7.018265] hub 1-0:1.0: 2 ports detected
[    7.022509] usb usb2: We don't know the algorithms for LPM for this
host, disabling LPM.
[    7.030842] hub 2-0:1.0: USB hub found
[    7.034600] hub 2-0:1.0: 1 port detected
[    7.040927] kmodloader: done loading kernel modules from
/etc/modules-boot.d/*
[    7.053822] init: - preinit -
[    7.552075] mtk_soc_eth 15100000.ethernet eth0: configuring for
fixed/2500base-x link mode
[    7.560532] mtk_soc_eth 15100000.ethernet eth0: Link is Up -
2.5Gbps/Full - flow control rx/tx
[    7.569171] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
ip: SIOCSIFHWADDR: Resource busy
[    7.720322] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii
link mode
[    7.732121] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full -
flow control rx/tx
[    7.740125] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.769837] UBIFS (ubi0:7): Mounting in unauthenticated mode
[    9.775556] UBIFS (ubi0:7): background thread "ubifs_bgt0_7" started,
PID 618
[    9.902466] UBIFS (ubi0:7): recovery needed
[   10.233118] UBIFS (ubi0:7): recovery completed
[   10.237606] UBIFS (ubi0:7): UBIFS: mounted UBI device 0, volume 7,
name "rootfs_data"
[   10.245415] UBIFS (ubi0:7): LEB size: 126976 bytes (124 KiB),
min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   10.255307] UBIFS (ubi0:7): FS size: 163926016 bytes (156 MiB, 1291
LEBs), max 1303 LEBs, journal size 8253440 bytes (7 MiB, 65 LEBs)
[   10.267282] UBIFS (ubi0:7): reserved for root: 4952683 bytes (4836 KiB)
[   10.273877] UBIFS (ubi0:7): media format: w5/r0 (latest is w5/r0),
UUID 357A43D5-232C-4EF8-8975-09578286A0F2, small LPT model
[   10.298786] mount_root: switching to ubifs overlay
[   10.314825] overlayfs: null uuid detected in lower fs '/', falling
back to xino=off,index=off,nfs_export=off.
[   10.339993] urandom-seed: Seeding with /etc/urandom.seed
[   10.418134] mt7530-mdio mdio-bus:1f lan1: Link is Down
[   10.425842] procd: - early -
[   10.428791] procd: - watchdog -
[   10.972943] procd: - watchdog -
[   10.976296] procd: - ubus -
[   11.033999] procd: - init -
Please press Enter to activate this console.
[   11.309569] kmodloader: loading kernel modules from /etc/modules.d/*
[   11.320636] crypto-safexcel 10320000.crypto:
EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433(alg:7fcdfc00)/0/0/0
[   11.334667] Loading modules backported from Linux version
v6.1.24-0-g0102425ac76b
[   11.342181] Backport generated by backports.git
v5.15.92-1-44-gd6ea70fafd36
[   11.455301] urngd: v1.0.2 started.
[   11.675685] mt798x-wmac 18000000.wifi: HW/SW Version: 0x8a108a10,
Build Time: 20221012174648a
[   11.675685]
[   11.998849] mt798x-wmac 18000000.wifi: WM Firmware Version:
____000000, Build Time: 20221012174725
[   12.147324] mt798x-wmac 18000000.wifi: WA Firmware Version:
DEV_000000, Build Time: 20221012174937
[   12.293454] mt798x-wmac 18000000.wifi: eeprom load fail, use default bin
[   19.869464] PPP generic driver version 2.4.2
[   19.874305] NET: Registered PF_PPPOX protocol family
[   19.881355] kmodloader: done loading kernel modules from /etc/modules.d/*
[   22.576848] mtk_soc_eth 15100000.ethernet eth0: Link is Down
[   22.590824] mtk_soc_eth 15100000.ethernet eth0: configuring for
fixed/2500base-x link mode
[   22.599501] mtk_soc_eth 15100000.ethernet eth0: Link is Up -
2.5Gbps/Full - flow control rx/tx
[   22.608223] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   22.618253] device eth0 entered promiscuous mode
[   22.623312] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii
link mode
[   22.633908] br-lan: port 1(lan1) entered blocking state
[   22.639229] br-lan: port 1(lan1) entered disabled state
[   22.645953] device lan1 entered promiscuous mode
[   22.661133] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii
link mode
[   22.670987] br-lan: port 2(lan2) entered blocking state
[   22.676221] br-lan: port 2(lan2) entered disabled state
[   22.683216] device lan2 entered promiscuous mode
[   22.694481] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii
link mode
[   22.704587] br-lan: port 3(lan3) entered blocking state
[   22.709846] br-lan: port 3(lan3) entered disabled state
[   22.716896] device lan3 entered promiscuous mode
[   22.727859] mt7530-mdio mdio-bus:1f lan4: configuring for phy/gmii
link mode
[   22.737864] br-lan: port 4(lan4) entered blocking state
[   22.743093] br-lan: port 4(lan4) entered disabled state
[   22.750586] device lan4 entered promiscuous mode
[   22.777545] mtk_soc_eth 15100000.ethernet eth1: PHY [mdio-bus:06]
driver [Maxlinear Ethernet GPY211C] (irq=POLL)
[   22.787720] mtk_soc_eth 15100000.ethernet eth1: configuring for
phy/2500base-x link mode
[   26.811643] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full -
flow control rx/tx
[   26.819589] br-lan: port 1(lan1) entered blocking state
[   26.824799] br-lan: port 1(lan1) entered forwarding state
[   26.830640] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   70.247108] mt798x-wmac 18000000.wifi: Message 00004eed (seq 13) timeout
[   90.727110] mt798x-wmac 18000000.wifi: Message 000007ed (seq 14) timeout


Remove power for few minutes, your wifi card used to work 10min ago