Hi, thx for the quick reply. I did not spot the dc_ep_clk_on failed
message in my kernel log. Here are a few pictures how it looks in LUCI:
Here is my network config for the dsl
config atm-bridge 'atm'
option vpi '1'
option vci '32'
option encaps 'llc'
option payload 'bridged'
option nameprefix 'dsl'
config dsl 'dsl'
option ds_snr_offset '0'
option annex 'b'
option xfer_mode 'ptm'
option line_mode 'vdsl'
option tone 'bv'
option firmware '/lib/firmware/vdsl.bin'
config device 'wan_dsl0_dev'
option name 'dsl0'
option macaddr 'DC:39:6F:EA:23:88'
config interface 'wan'
option device 'dsl0'
option proto 'pppoe'
option username '[redacted]@t-online.de'
option password '[redacted]'
option ipv6 'auto'
option keepalive '9 6'
option dns_metric '6'
For completes here is also the kernel log
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.15.102 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 12.2.0 r22325-00b40ef00d) 12.2.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Mon Mar 20 02:10:43 2023
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: AVM FRITZ!Box 7530
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000080000000-0x000000008fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080000000-0x0000000087dfffff]
[ 0.000000] node 0: [mem 0x0000000087e00000-0x0000000087ffffff]
[ 0.000000] node 0: [mem 0x0000000088000000-0x000000008fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000008fffffff]
[ 0.000000] percpu: Embedded 12 pages/cpu s16588 r8192 d24372 u49152
[ 0.000000] pcpu-alloc: s16588 r8192 d24372 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: coherent_pool=4M
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 246184K/262144K available (6823K kernel code, 610K rwdata, 1708K rodata, 1024K init, 247K bss, 15960K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns
[ 0.000002] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns
[ 0.000025] Switching to timer-based delay loop, resolution 20ns
[ 0.000319] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000)
[ 0.000349] pid_max: default: 32768 minimum: 301
[ 0.000580] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.000608] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.001622] CPU: Testing write buffer coherency: ok
[ 0.002000] qcom_scm: convention: smc legacy
[ 0.003113] Setting up static identity map for 0x80300000 - 0x8030003c
[ 0.003286] rcu: Hierarchical SRCU implementation.
[ 0.003538] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.003870] smp: Bringing up secondary CPUs ...
[ 0.007189] smp: Brought up 1 node, 4 CPUs
[ 0.007226] SMP: Total of 4 processors activated (384.00 BogoMIPS).
[ 0.007241] CPU: All CPU(s) started in SVC mode.
[ 0.012043] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.012211] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.012245] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.012500] pinctrl core: initialized pinctrl subsystem
[ 0.014143] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.017128] DMA: preallocated 4096 KiB pool for atomic coherent allocations
[ 0.018252] thermal_sys: Registered thermal governor 'step_wise'
[ 0.018674] cpuidle: using governor ladder
[ 0.018735] cpuidle: using governor menu
[ 0.026434] gpio-461 (enable USB3 power): hogged as output/high
[ 0.044531] cryptd: max_cpu_qlen set to 1000
[ 0.048719] usbcore: registered new interface driver usbfs
[ 0.048794] usbcore: registered new interface driver hub
[ 0.048853] usbcore: registered new device driver usb
[ 0.048907] pps_core: LinuxPPS API ver. 1 registered
[ 0.048920] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.048949] PTP clock support registered
[ 0.050982] clocksource: Switched to clocksource arch_sys_counter
[ 0.051933] NET: Registered PF_INET protocol family
[ 0.052154] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.052953] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.053008] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.053030] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.053074] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.053129] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.053248] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.053294] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.053576] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.053631] PCI: CLS 0 bytes, default 64
[ 0.055940] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.060752] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.060793] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.190646] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 0.193127] qcom-pcie 40000000.pci: host bridge /soc/pci@40000000 ranges:
[ 0.193200] qcom-pcie 40000000.pci: IO 0x0040200000..0x00402fffff -> 0x0040200000
[ 0.193238] qcom-pcie 40000000.pci: MEM 0x0040300000..0x0040ffffff -> 0x0040300000
[ 0.372561] qcom-pcie 40000000.pci: iATU unroll: disabled
[ 0.372593] qcom-pcie 40000000.pci: Detected iATU regions: 32 outbound, 8 inbound
[ 0.472691] qcom-pcie 40000000.pci: Link up
[ 0.472890] qcom-pcie 40000000.pci: PCI host bridge to bus 0000:00
[ 0.472914] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.472938] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0x40200000-0x402fffff])
[ 0.472957] pci_bus 0000:00: root bus resource [mem 0x40300000-0x40ffffff]
[ 0.473016] pci 0000:00:00.0: [17cb:1001] type 01 class 0x060400
[ 0.473051] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff]
[ 0.473122] pci 0000:00:00.0: PME# supported from D0 D3hot
[ 0.474624] PCI: bus0: Fast back to back transfers disabled
[ 0.474846] pci 0000:01:00.0: [8086:09a9] type 00 class 0x028000
[ 0.474934] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x007fffff]
[ 0.475337] pci 0000:01:00.0: supports D1 D2
[ 0.475352] pci 0000:01:00.0: PME# supported from D0 D1 D3hot D3cold
[ 0.476923] PCI: bus1: Fast back to back transfers disabled
[ 0.476972] pci 0000:00:00.0: BAR 8: assigned [mem 0x40800000-0x40ffffff]
[ 0.476995] pci 0000:00:00.0: BAR 0: assigned [mem 0x40300000-0x40300fff]
[ 0.477020] pci 0000:01:00.0: BAR 0: assigned [mem 0x40800000-0x40ffffff]
[ 0.477053] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.477074] pci 0000:00:00.0: bridge window [mem 0x40800000-0x40ffffff]
[ 0.479890] pcieport 0000:00:00.0: AER: enabled with IRQ 102
cut for space reasons
[ 11.374639] UBIFS (ubi0:4): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 11.382667] UBIFS (ubi0:4): FS size: 83677184 bytes (79 MiB, 659 LEBs), max 670 LEBs, journal size 4190208 bytes (3 MiB, 33 LEBs)
[ 11.392534] UBIFS (ubi0:4): reserved for root: 3952280 bytes (3859 KiB)
[ 11.404120] UBIFS (ubi0:4): media format: w5/r0 (latest is w5/r0), UUID F4F2078B-B46D-41E6-B559-5B6FDE6238C1, small LPT model
[ 11.421967] mount_root: switching to ubifs overlay
[ 11.443115] urandom-seed: Seeding with /etc/urandom.seed
[ 11.621596] procd: - early -
[ 11.621814] procd: - watchdog -
[ 12.234753] procd: - watchdog -
[ 12.248220] procd: - ubus -
[ 12.329953] procd: - init -
[ 13.314679] kmodloader: loading kernel modules from /etc/modules.d/*
[ 13.346898] urngd: v1.0.2 started.
[ 13.408639] IFXOS, Version 1.7.1 (c) Copyright 2009, Lantiq Deutschland GmbH
[ 13.410584] vrx518: Intel(R) SmartPHY DSL(VRX518) PCIe EP/ACA Driver - version 2.1.0-k
[ 13.414818] vrx518: Copyright (c) 2016 Intel Corporation.
[ 13.422693] vrx518 0000:01:00.0: enabling device (0140 -> 0142)
[ 13.431525] NET: Registered PF_ATMPVC protocol family
[ 13.433698] NET: Registered PF_ATMSVC protocol family
[ 13.446217] vrx518_tc:pcie_ep_probe: Total 1 VRX518 EP detected
[ 13.459910] MD5 checksum pass!!!
[ 13.459957] Firmware pointer id(0):size(10636), fw addr(d32c2046), off(100)
[ 13.462262] Firmware pointer id(1):size(19548), fw addr(fb7b9b1b), off(10736)
[ 13.468905] Firmware pointer id(2):size(11504), fw addr(63b5bcbc), off(30284)
[ 13.476232] Firmware pointer id(3):size(23076), fw addr(93c969bf), off(41788)
[ 13.483332] VRX518 PPE Firmware header info
[ 13.490429] PTM Version: 3.5.75
[ 13.494431] PTM Feature: A0000000
[ 13.497891] ATM Version: 3.6.5
[ 13.501113] ATM Feature: B0000000
[ 13.504141] Compability ID: 00000004
[ 13.507614] Size: 00000010
[ 13.511356] FW built Date: 3-25-2021
[ 13.513952] Number of firmware: 4
[ 13.517770] Firmware[0]: ID[0] size[2659] at[0xd32c2046]
[ 13.521082] Firmware[1]: ID[1] size[4887] at[0xfb7b9b1b]
[ 13.526541] Firmware[2]: ID[2] size[2876] at[0x63b5bcbc]
[ 13.532021] Firmware[3]: ID[3] size[5769] at[0x93c969bf]
[ 13.537567] vrx518_tc:tc_drv_init: Intel(R) SmartPHY DSL(VRX518) PCIe TC Driver - version 1.5.12.4
[ 13.542969] vrx518_tc:tc_drv_init: Copyright (c) 2018 Intel Corporation.
[ 13.563262] Lantiq (VRX) DSL CPE MEI driver, version 1.11.1, (c) 2007-2016 Lantiq Deutschland GmbH
[ 13.563519] Found 1 PCI VRX devices,
[ 13.579529]
[ 13.579529]
[ 13.579529] Lantiq CPE API Driver version: DSL CPE API V4.23.1
[ 13.579589]
[ 13.579589]
[ 13.579589] Lantiq CPE API Driver - autoloading layout...
[ 13.587446]
[ 13.587446]
[ 13.587446] Lantiq CPE API Device layout: 1 devices, 1 lines, 1 channels
[ 13.595526]
[ 13.595526] Predefined debug level: 3
[ 13.605213]
[ 13.605213] ++++++++++++++++++ MEI_InternalDevOpen ++++++++++++++++++
[ 13.605213]
[ 13.610677]
[ 13.610677] ++++++++++++++++++ MEI_InternalDevOpen ++++++++++++++++++
[ 13.610677]
[ 13.632669] Loading modules backported from Linux version v6.1-rc8-0-g76dcd734eca2
[ 13.632721] Backport generated by backports.git v5.15.81-1-41-g02e352527db5
[ 13.722223] PPP generic driver version 2.4.2
[ 13.724264] NET: Registered PF_PPPOX protocol family
[ 13.744956] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 13.745010] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 14.839298] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[ 14.839368] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 14.851255] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
[ 14.902941] ath10k_ahb a000000.wifi: Loading BDF type 0
[ 14.964961] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:20 crc32 de0d18b2
[ 16.252581] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 16.252659] ath10k_ahb a000000.wifi: msdu-desc: 2500 skid: 32
[ 16.287189] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 16.288190] ath10k_ahb a000000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752'
[ 16.433449] ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 16.615071] ath: EEPROM regdomain: 0x0
[ 16.615099] ath: EEPROM indicates default country code should be used
[ 16.615106] ath: doing EEPROM country->regdmn map search
[ 16.615114] ath: country maps to regdmn code: 0x3a
[ 16.615121] ath: Country alpha2 being used: US
[ 16.615129] ath: Regpair used: 0x3a
[ 17.961089] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[ 17.961184] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 17.974465] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
[ 18.024768] ath10k_ahb a800000.wifi: Loading BDF type 0
[ 18.032528] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:21 crc32 de0d18b2
[ 19.320021] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 19.320092] ath10k_ahb a800000.wifi: msdu-desc: 2500 skid: 32
[ 19.355763] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 19.356775] ath10k_ahb a800000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752'
[ 19.481808] ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 19.629518] ath: EEPROM regdomain: 0x0
[ 19.629546] ath: EEPROM indicates default country code should be used
[ 19.629552] ath: doing EEPROM country->regdmn map search
[ 19.629560] ath: country maps to regdmn code: 0x3a
[ 19.629568] ath: Country alpha2 being used: US
[ 19.629575] ath: Regpair used: 0x3a
[ 19.639927] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 26.920529] ipqess-edma c080000.ethernet eth0: Link is Down
[ 26.927419] ipqess-edma c080000.ethernet eth0: configuring for fixed/internal link mode
[ 26.927741] ipqess-edma c080000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 26.934970] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 26.945451] qca8k-ipq4019 c000000.switch lan1: configuring for phy/psgmii link mode
[ 26.954008] br-lan: port 1(lan1) entered blocking state
[ 26.956489] br-lan: port 1(lan1) entered disabled state
[ 26.962562] device lan1 entered promiscuous mode
[ 26.966897] device eth0 entered promiscuous mode
[ 27.001490] qca8k-ipq4019 c000000.switch lan2: configuring for phy/psgmii link mode
[ 27.007847] br-lan: port 2(lan2) entered blocking state
[ 27.007992] br-lan: port 2(lan2) entered disabled state
[ 27.013884] device lan2 entered promiscuous mode
[ 27.026395] qca8k-ipq4019 c000000.switch lan3: configuring for phy/psgmii link mode
[ 27.029059] br-lan: port 3(lan3) entered blocking state
[ 27.033075] br-lan: port 3(lan3) entered disabled state
[ 27.038597] device lan3 entered promiscuous mode
[ 27.055779] qca8k-ipq4019 c000000.switch lan4: configuring for phy/psgmii link mode
[ 27.058331] br-lan: port 4(lan4) entered blocking state
[ 27.062384] br-lan: port 4(lan4) entered disabled state
[ 27.068290] device lan4 entered promiscuous mode
[ 29.694052] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 29.694125] ath10k_ahb a000000.wifi: msdu-desc: 2500 skid: 32
[ 29.729444] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 29.730273] ath10k_ahb a000000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752'
[ 30.079294] ath10k_ahb a000000.wifi: rts threshold -1
[ 30.081171] ath10k_ahb a000000.wifi: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 30.163823] qca8k-ipq4019 c000000.switch lan4: Link is Up - 1Gbps/Full - flow control rx/tx
[ 30.163933] br-lan: port 4(lan4) entered blocking state
[ 30.171065] br-lan: port 4(lan4) entered forwarding state
[ 30.176710] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 30.565499] ath10k_ahb a000000.wifi: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
[ 31.065920] phy0-sta0: authenticate with e0:28:6d:36:cf:73
[ 31.066041] phy0-sta0: 80 MHz not supported, disabling VHT
[ 31.280488] phy0-sta0: send auth to e0:28:6d:36:cf:73 (try 1/3)
[ 31.284463] phy0-sta0: authenticated
[ 31.291111] phy0-sta0: associate with e0:28:6d:36:cf:73 (try 1/3)
[ 31.293600] phy0-sta0: RX AssocResp from e0:28:6d:36:cf:73 (capab=0x31 status=0 aid=3)
[ 31.297649] ath10k_ahb a000000.wifi: pdev param 0 not supported by firmware
[ 31.304168] ath10k_ahb a000000.wifi: failed to enable peer stats info: -95
[ 31.311148] phy0-sta0: associated
[ 31.323015] ath10k_ahb a000000.wifi: Invalid peer id 0 or peer stats buffer, peer: 00000000 sta: 00000000
[ 31.572600] IPv6: ADDRCONF(NETDEV_CHANGE): phy0-sta0: link becomes ready
[ 1179.664395] plat_tc_request: dsl id: 0, mode: 1, tc_mode: 3, tc_idx: -1
[ 1179.665470] vrx518_tc:ptm_tc_hw_fw_init: id(Line) = 0
[ 1179.667026] vrx518_tc:ptm_set_mac_address: ptm mac address update!
[ 1179.669888] vrx518_tc:ptm_tc_hw_fw_init: irq = 107
[ 1179.669915] vrx518_tc:ptm_tc_hw_fw_init: membase = 0xd1600000
[ 1179.675382] vrx518_tc:ptm_open: ptm open
[ 1179.681292] vrx518_tc:ptm_tc_hw_fw_init: phy_membase = 0x40800000
[ 1179.696057] vrx518_tc:ptm_tc_hw_fw_init: peer_num = 0
[ 1179.702087] vrx518_tc:ptm_tc_hw_fw_init: tc_mode = PTM Single Line
[ 1179.727203] vrx518_tc:is_ptm_sl: is_ptm_sl: SINGLE
[ 1179.727262] vrx518_tc:is_ptm_sl: is_ptm_sl: SINGLE
[ 1179.731579] vrx518_tc:is_ptm_sl: is_ptm_sl: SINGLE
[ 1179.735683] ppe_aca_cfg_cnt: priv->ep_id[0] bond[0]
[ 1179.740476] ppe_aca_cfg_cnt: 0 0 0 0
[ 1179.745227] ppe_aca_cfg_cnt: cfg->txin.soc_cnt_phyaddr[0]
[ 1179.749047] ppe_aca_cfg_cnt: cfg->txout.soc_cnt_phyaddr[0]
[ 1179.754361] ppe_aca_cfg_cnt: cfg->rxout.soc_cnt_phyaddr[0]
[ 1179.759752] ppe_aca_cfg_cnt: cfg->rxin.soc_cnt_phyaddr[0]
[ 1179.765198] Loading PTM FW ver: 3.5.75
[ 1179.791876] vrx518_tc:ptm_tc_hw_fw_init: PTM TC init successfully
[ 1179.791915] id: 0, txin(0x82835000: 128, 0x0), txout(0x82834000: 128, 0x0), rxin(0x0: 0, 0x0), rxout(0x825d8000: 1024, 0x0)
[ 1179.796960] vrx518_tc:ptm_aca_init: txin: bswp: 0, hdsz:4, pd: dbase(0x2801c0), dnum(32), sz_indw(2), soc_dbase:0x82835000, soc_dnum:0x80, soc cnt addr: 0x40b21480
[ 1179.807926] vrx518_tc:ptm_aca_init: txout: bswp: 0, hdsz:1, pd: dbase(0x230000), dnum(64), sz_indw(2), soc_dbase:0x82834000, soc_dnum:0x80, soc cnt addr: 0x40b21484
[ 1179.822506] vrx518_tc:ptm_aca_init: rxout: bswp: 0, hdsz:4, pd: dbase(0x230200), dnum(255), sz_indw(2), soc_dbase:0x825d8000, soc_dnum:0x400, soc cnt addr: 0x40b21488
[ 1179.837433] vrx518_tc:ptm_aca_init: rxin: bswp: 0, hdsz:4, pd: dbase(0x2855c0), dnum(255), sz_indw(2), soc_dbase:0x0, soc_dnum:0x0, soc cnt addr: 0x40b2148c
[ 1179.852104] vrx518_tc:ptm_aca_init: txout: (stat:0x40b6b7d0, pd: 0x40b6b7d4, cnt: 0x40b6b7cc)
[ 1179.866247] vrx518_tc:ptm_aca_init: rxout: (stat:0x40b6b7e8, pd: 0x40b6b7ec, cnt: 0x40b6b7e4)
[ 1179.874664] vrx518_tc:ptm_aca_init: rxin: (stat:0x40b6b7dc, pd: 0x40b6b7e0, cnt: 0x40b6b7d8)
[ 1179.885985] vrx518 0000:01:00.0: ACA fw build 0 branch 4 major 0x20 minor 0x0016
[ 1179.891712] vrx518 0000:01:00.0: ACA fw for vrx518 supported SoC type xrx500
[ 1179.899038] vrx518 0000:01:00.0: Header size 0x0000019c fw size 0x00000904
[ 1179.899051] vrx518 0000:01:00.0: section number 14
[ 1179.899062] vrx518 0000:01:00.0: Section HIF ie_len 1
[ 1179.899074] vrx518 0000:01:00.0: Section GenRisc ie_len 2
[ 1179.899085] vrx518 0000:01:00.0: Section MAC_HT ie_len 3
[ 1179.899096] vrx518 0000:01:00.0: Section TXIN ie_len 1
[ 1179.899107] vrx518 0000:01:00.0: Sec TXIN desc base 0x00100128, des_num: 32
[ 1179.899124] vrx518 0000:01:00.0: Section TXIN_PDRING ie_len 1
[ 1179.899135] vrx518 0000:01:00.0: Sec TXIN_PDRING desc base 0x00100528, des_num: 64
[ 1179.899149] vrx518 0000:01:00.0: Section TXOUT ie_len 1
[ 1179.899161] vrx518 0000:01:00.0: Sec TXOUT desc base 0x00100728, des_num: 32
[ 1179.899175] vrx518 0000:01:00.0: Section TXOUT_PDRING ie_len 1
[ 1179.899186] vrx518 0000:01:00.0: Sec TXOUT_PDRING desc base 0x00100b28, des_num: 32
[ 1179.899199] vrx518 0000:01:00.0: Section RXIN ie_len 1
[ 1179.899210] vrx518 0000:01:00.0: Sec RXIN desc base 0x00100c28, des_num: 32
[ 1179.899224] vrx518 0000:01:00.0: Section RXIN_PDRING ie_len 1
[ 1179.899236] vrx518 0000:01:00.0: Sec RXIN_PDRING desc base 0x00101028, des_num: 32
[ 1179.899249] vrx518 0000:01:00.0: Section RXOUT ie_len 1
[ 1179.899260] vrx518 0000:01:00.0: Sec RXOUT desc base 0x00101128, des_num: 32
[ 1179.899273] vrx518 0000:01:00.0: Section RXOUT_PDRING ie_len 1
[ 1179.899284] vrx518 0000:01:00.0: Sec RXOUT_PDRING desc base 0x00101528, des_num: 256
[ 1179.899298] vrx518 0000:01:00.0: Section DMA ie_len 10
[ 1179.899309] vrx518 0000:01:00.0: dma channel 0 desc base 0x00100000
[ 1179.899321] vrx518 0000:01:00.0: dma channel 1 desc base 0x00100008
[ 1179.899333] vrx518 0000:01:00.0: dma channel 2 desc base 0x00100010
[ 1179.899344] vrx518 0000:01:00.0: dma channel 3 desc base 0x00100018
[ 1179.899394] vrx518 0000:01:00.0: dma channel 4 desc base 0x00100030
[ 1179.899409] vrx518 0000:01:00.0: dma channel 5 desc base 0x00100038
[ 1179.899421] vrx518 0000:01:00.0: dma channel 6 desc base 0x00100020
[ 1179.899433] vrx518 0000:01:00.0: dma channel 7 desc base 0x00100028
[ 1179.899444] vrx518 0000:01:00.0: dma channel 8 desc base 0x00100040
[ 1179.899455] vrx518 0000:01:00.0: dma channel 9 desc base 0x00100048
[ 1179.899467] vrx518 0000:01:00.0: Section FW_INIT ie_len 1
[ 1179.899479] vrx518 0000:01:00.0: init st size: 32, addr: 0x100060
[ 1179.899491] vrx518 0000:01:00.0: Section ACA FW ie_len 5
[ 1179.899503] vrx518 0000:01:00.0: aca txin fw offset 0x0 size 20 loc 0x50800 fw base 9ec2b38c
[ 1179.899523] vrx518 0000:01:00.0: aca txout fw offset 0x14 size 4 loc 0x50900 fw base 4e283617
[ 1179.899539] vrx518 0000:01:00.0: aca rxin fw offset 0x18 size 4 loc 0x50a00 fw base faab45c9
[ 1179.899555] vrx518 0000:01:00.0: aca rxout fw offset 0x1c size 24 loc 0x50b00 fw base d66d2c78
[ 1179.899571] vrx518 0000:01:00.0: aca Genrisc fw offset 0x34 size 2256 loc 0x58000 fw base f762c1aa
[ 1179.899694] vrx518 0000:01:00.0: aca dma init done
[ 1179.899708] vrx518 0000:01:00.0: aca basic config done
[ 1179.900614] vrx518 0000:01:00.0: aca_hif_param_init
[ 1179.900625] vrx518 0000:01:00.0: aca txin init done
[ 1179.900634] vrx518 0000:01:00.0: aca txout init done
[ 1179.900644] vrx518 0000:01:00.0: aca rxout init done
[ 1179.900653] vrx518 0000:01:00.0: aca rxin init done
[ 1179.900662] vrx518 0000:01:00.0: init_addr: 100060
[ 1179.900674] vrx518 0000:01:00.0: aca_hif_param_init_done
[ 1179.900686] vrx518 0000:01:00.0: aca mdm init done
[ 1179.900695] vrx518 0000:01:00.0: aca init done
[ 1179.906068] vrx518_tc:is_ptm_sl: is_ptm_sl: SINGLE
[ 1179.910508] Sent TC multicast message Fail!
[ 1179.915177] vrx518_tc:ptm_tc_load: PTM TC is successfully loaded
[ 1180.170065] vrx518_tc:is_ptm_sl: is_ptm_sl: SINGLE
[ 1180.170429] vrx518_tc:ptm_erb_addr_get: idx: 0, data addr: 0x40a30000, desc_addr: 0x40b60000
[ 1275.985750] vrx518_tc:ptm_showtime_enter: Line[0]: show time enter!!
[ 1275.986360] vrx518_tc:is_ptm_sl: is_ptm_sl: SINGLE
[ 1275.992495] IPv6: ADDRCONF(NETDEV_CHANGE): dsl0: link becomes ready
[ 1291.564885] vrx518_tc:ptm_stop: ptm stop
[ 1291.568813] vrx518_tc:ptm_set_mac_address: ptm mac address update!
[ 1291.570942] vrx518_tc:ptm_set_mac_address: ptm mac address update!
[ 1291.574151] vrx518_tc:ptm_open: ptm open
[ 1307.063303] vrx518_tc:ptm_stop: ptm stop
[ 1307.067754] vrx518_tc:ptm_set_mac_address: ptm mac address update!
[ 1307.070629] vrx518_tc:ptm_set_mac_address: ptm mac address update!