Ok, compiled latest trunk (r29644) and did a upgrade from stock Linksys firmware admin pages on E3000.... here is a boot log off console!
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Jul 27 16:07:16 CST 2010 (ljh@team2-complier)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
No DPN
This is a Parallel Flash
Boot partition size = 262144(0x40000)
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.51
CPU type 0x19740: 480MHz
Tot mem: 65536 KBytes
CFE mem: 0x80700000 - 0x8079DAC0 (645824)
Data: 0x80732A20 - 0x80737080 (18016)
BSS: 0x80737080 - 0x80737AC0 (2624)
Heap: 0x80737AC0 - 0x8079BAC0 (409600)
Stack: 0x8079BAC0 - 0x8079DAC0 (8192)
Text: 0x80700000 - 0x80732A1C (207388)
Boot version: v4.2
The boot is CFE
mac_init(): Find mac [98:FC:11:91:6B:F4] in location 0
Nothing...
country_init(): Find country code in location 0
The country is same
Device eth0: hwaddr 98-FC-11-91-6B-F4, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Check CRC of image1
Header CRC: 0xDE8C3C86
Calculate CRC: 0xDE8C3C86
Image 1 is OK
Try to load image 1.
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3788 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
[ 0.000000] Linux version 3.0.12 (adminsag@ipcx201ubuntu1) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #
2 Tue Jan 3 21:46:05 CST 2012
[ 0.000000] CPU revision is: 00019740 (MIPS 74Kc)
[ 0.000000] bcm47xx: using ssb bus
[ 0.000000] ssb: Found END of erom after 9 cores
[ 0.000000] ssb: chipcommon status is 0x800
[ 0.000000] ssb: ssb_pmu_resources_init: Resource count 7
[ 0.000000] ssb: Initializing MIPS core...
[ 0.000000] ssb: set_irq: core 0x0812, irq 3 => 3
[ 0.000000] ssb: set_irq: core 0x082d, irq 4 => 4
[ 0.000000] ssb: set_irq: core 0x0819, irq 5 => 5
[ 0.000000] ssb: after irq reconfiguration
[ 0.000000] ssb: core 0x0800, irq : 2(S)* 3 4 5 6 D I
[ 0.000000] ssb: core 0x0812, irq : 2(S) 3* 4 5 6 D I
[ 0.000000] ssb: core 0x082d, irq : 2(S) 3 4* 5 6 D I
[ 0.000000] ssb: core 0x082c, irq : 2(S) 3 4 5 6 D I*
[ 0.000000] ssb: core 0x0819, irq : 2(S) 3 4 5* 6 D I
[ 0.000000] ssb: core 0x0820, irq : 2(S) 3 4 5 6* D I
[ 0.000000] ssb: core 0x082e, irq : 2(S)* 3 4 5 6 D I
[ 0.000000] ssb: core 0x080e, irq : 2(S) 3 4 5 6 D I*
[ 0.000000] ssb: core 0x0834, irq : 2(S)* 3 4 5 6 D I
[ 0.000000] found parallel flash.
[ 0.000000] ssb: Sonics Silicon Backplane (AI type) found at address 0x18000000
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 62192k/65536k available (2095k kernel code, 3344k reserved, 332k data, 156k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] console [ttyS0] enabled
[ 0.004000] Calibrating delay loop... 239.10 BogoMIPS (lpj=478208)
[ 0.040000] pid_max: default: 32768 minimum: 301
[ 0.044000] Mount-cache hash table entries: 512
[ 0.048000] NET: Registered protocol family 16
[ 0.060000] bio: create slab <bio-0> at 0
[ 0.068000] Switching to clocksource MIPS
[ 0.076000] Switched to NOHz mode on CPU #0
[ 0.084000] NET: Registered protocol family 2
[ 0.088000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.096000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.104000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.112000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.116000] TCP reno registered
[ 0.120000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.124000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.132000] NET: Registered protocol family 1
[ 0.144000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.152000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.160000] msgmni has been set to 121
[ 0.164000] io scheduler noop registered
[ 0.168000] io scheduler deadline registered (default)
[ 0.176000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
\FD 0.20000 serial8250: ttyS0 at MMIO 0xb8000300 (irq = 2) is a U6_16550A
[ 0.232000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2) is a U6_16550A
[ 0.240000] bcm47xx_pflash: flash init: 0x1c000000 0x02000000
[ 0.248000] Physically mapped flash: Found 1 x16 devices at 0x0 in 8-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0000cb
[ 0.256000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.264000] Amd/Fujitsu Extended Query version 1.1.
[ 0.268000] number of CFI chips: 1
[ 0.272000] bcm47xx_pflash: Flash device: 0x2000000 at 0x1fc00000
[ 0.280000] bcm47xx_part: bootloader size: 262144
[ 0.284000] bcm47xx_part: Looking for dual image
[ 0.288000] bcm47xx_part: TRX offset : 0
[ 0.292000] 4 bcm47xx partitions found on MTD device Physically mapped flash
[ 0.300000] Creating 4 MTD partitions on "Physically mapped flash":
[ 0.308000] 0x000000000000-0x000000040000 : "cfe"
[ 0.312000] 0x000000040000-0x0000007f0000 : "linux"
[ 0.320000] 0x000000117000-0x0000007f0000 : "rootfs"
[ 0.328000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcin
g read-only
[ 0.340000] mtd: partition "rootfs" set to be root filesystem
[ 0.348000] mtd: partition "rootfs_data" created automatically, ofs=320000, len=4D0000
[ 0.356000] 0x000000320000-0x0000007f0000 : "rootfs_data"
[ 0.364000] 0x0000007f0000-0x000000800000 : "nvram"
[ 0.372000] bcm47xx_sflash: error registering platform driver: -19
[ 0.380000] BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
[ 0.388000] TCP westwood registered
[ 0.392000] NET: Registered protocol family 17
[ 0.396000] 802.1Q VLAN Support v1.8
[ 0.408000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.416000] Freeing unused kernel memory: 156k freed
[ 1.972000] diag: Router model not detected.
[ 3.168000] roboswitch: Probing device eth0: No such device
[ 3.176000] roboswitch: Probing device eth1: No such device
[ 3.180000] roboswitch: Probing device eth2: No such device
[ 3.184000] roboswitch: Probing device eth3: No such device
[ 6.296000] diag: Router model not detected.
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[ 9.600000] JFFS2 notice: (264) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orph
an) and 4 of xref (0 dead, 2 orphan) found.
switching to jffs2
- init -
Please press Enter to activate this console. [ 11.676000] bgmac ssb0:1: eth0: Broadcom SSB GMAC ethernet driver (ext. Robo Switch
) 00:01:36:1f:e4:59
[ 11.792000] USB20H mdio control register: 0x8000000C
[ 11.996000] SCSI subsystem initialized
[ 12.032000] roboswitch: Probing device eth0: found a 53115! It's a 5350.
[ 12.208000] usbcore: registered new interface driver usbfs
[ 12.212000] usbcore: registered new interface driver hub
[ 12.224000] usbcore: registered new device driver usb
[ 13.144000] wl: module license 'unspecified' taints kernel.
[ 13.148000] Disabling lock debugging due to kernel taint
[ 13.228000] wl0: Broadcom BCM4329 802.11 Wireless Controller 5.10.56.27
[ 13.236000] SSB/BCMA glue driver successfully attached
[ 13.752000] PPP generic driver version 2.4.2
[ 14.076000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.284000] NET: Registered protocol family 24
[ 14.432000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 14.436000] ehci-platform ehci-platform.0: Generic Platform EHCI Controller
[ 14.444000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 14.476000] ehci-platform ehci-platform.0: irq 5, io mem 0x18004000
[ 14.492000] ehci-platform ehci-platform.0: USB 0.0 started, EHCI 1.00
[ 14.496000] hub 1-0:1.0: USB hub found
[ 14.500000] hub 1-0:1.0: 2 ports detected
[ 14.532000] nf_conntrack version 0.5.0 (974 buckets, 3896 max)
[ 15.164000] uhci_hcd: USB Universal Host Controller Interface driver
[ 15.192000] Initializing USB Mass Storage driver...
[ 15.200000] usbcore: registered new interface driver usb-storage
[ 15.204000] USB Mass Storage support registered.
[ 16.920000] device eth0.0 entered promiscuous mode
[ 16.924000] device eth0 entered promiscuous mode
[ 17.268000] br-lan: port 1(eth0.0) entering forwarding state
[ 17.272000] br-lan: port 1(eth0.0) entering forwarding state
BusyBox v1.19.3 (2012-01-03 21:25:37 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
ATTITUDE ADJUSTMENT (bleeding edge, r29643) ----------
* 1/4 oz Vodka Pour all ingredients into mixing
* 1/4 oz Gin tin with ice, strain into glass.
* 1/4 oz Amaretto
* 1/4 oz Triple sec
* 1/4 oz Peach schnapps
* 1/4 oz Sour mix
* 1 splash Cranberry juice
-----------------------------------------------------
root@OpenWrt:/#
It is working pretty good so far. I was able to make the router an Access Point using WPA2 encryption using LuCI. If anyone else wants a copy, here is the Cisco Linksys E3000 binary for R29644 (the bootlog shown in this post), LuCI included: https://sites.google.com/site/stephengu … uashfs.bin
We tested the router as an Access Point at our Austin Linux meeting tonight. Seems to max out wireless throughput around 1.5Mbps... pretty crappy. This was from various client 802.11n systems, 4 active ones. CPU was not maxed out, so not sure what is going on with the wireless driver.
(Last edited by RoundSparrow on 5 Jan 2012, 04:59)