After installing the software, it runs in a loop. It is impossible to stop this loop. Is there a solution to reinstall the software. I tried the reset, I work directly with minicom, but it does not react to the break.
Is there a solution even if you have to open the switch ?
� Enable PHY Polling
Misc
PHY init (unit 0)
Mgmt_dev init (unit 0)
Please wait for PHY init-time ...
Booting kernel from Legacy Image at 81000000 ...
Image Name: MIPS OpenWrt Linux-6.6.69
Created: 2025-01-04 21:35:37 UTC
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 3616351 Bytes = 3.4 MB
Load Address: 80100000
Entry Point: 80100000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 6.6.69 (builder@buildhost) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r28304-6dacba30a7) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 Sat Jan 4 21:35:37 2025
[ 0.000000] RTL838X model is 0
[ 0.000000] RTL839X model is 0
[ 0.000000] RTL93XX model is 93021001
[ 0.000000] SoC Type: RTL9302B
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019555 (MIPS 34Kc)
[ 0.000000] MIPS: machine is Zyxel XGS1250-12 Switch
[ 0.000000] earlycon: ns16550a0 at MMIO 0x18002000 (options '115200n8')
[ 0.000000] printk: bootconsole [ns16550a0] enabled
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Using appended Device Tree.
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Kernel command line: earlycon
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=00058090
[ 0.000000] Readback ErrCtl register=00058090
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 119836K/131072K available (6940K kernel code, 632K rwdata, 888K rodata, 1196K init, 235K bss, 11236K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] Failed to get CPU clock: -2
[ 0.000000] CPU frequency from device tree: 800MHz
[ 0.000000] clocksource: realtek_otto_timer: mask: 0xfffffff max_cycles: 0xfffffff, max_idle_ns: 38225208801 ns
[ 0.000002] sched_clock: 28 bits at 3125kHz, resolution 320ns, wraps every 42949672800ns
[ 0.009033] Calibrating delay loop... 531.66 BogoMIPS (lpj=2658304)
[ 0.065702] pid_max: default: 32768 minimum: 301
[ 0.080872] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.088906] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.106973] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=1.
[ 0.123416] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.134214] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.144296] pinctrl core: initialized pinctrl subsystem
[ 0.152633] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.159808] thermal_sys: Registered thermal governor 'step_wise'
[ 0.174187] clocksource: Switched to clocksource realtek_otto_timer
[ 0.198828] NET: Registered PF_INET protocol family
[ 0.204500] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.213984] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.223296] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.231792] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.240200] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.247948] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.255699] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.263866] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.271085] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.279720] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.292119] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.300994] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.307443] jffs2: version 2.2 (NAND) (SUMMARY) (ZLIB) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.326691] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.336328] pinctrl-single 1b00cc00.pinmux: 32 pins, size 4
[ 0.344308] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.358218] printk: console [ttyS0] disabled
[ 0.363478] 18002000.uart: ttyS0 at MMIO 0x18002000 (irq = 30, base_baud = 10937500) is a 16550A
[ 0.373185] printk: console [ttyS0] enabled
[ 0.373185] printk: console [ttyS0] enabled
[ 0.382528] printk: bootconsole [early0] disabled
[ 0.382528] printk: bootconsole [early0] disabled
[ 0.428045] printk: bootconsole [ns16550a0] disabled
[ 0.428045] printk: bootconsole [ns16550a0] disabled
[ 0.478593] brd: module loaded
[ 0.485957] spi-nor spi0.0: mx25l12805d (16384 Kbytes)
[ 0.491870] 7 fixed-partitions partitions found on MTD device spi0.0
[ 0.499049] OF: Bad cell count for /soc/spi@1200/flash@0/partitions
[ 0.506093] OF: Bad cell count for /soc/spi@1200/flash@0/partitions
[ 0.513320] Creating 7 MTD partitions on "spi0.0":
[ 0.518723] 0x000000000000-0x0000000e0000 : "u-boot"
[ 0.527538] 0x0000000e0000-0x0000000f0000 : "u-boot-env"
[ 0.536044] 0x0000000f0000-0x000000100000 : "u-boot-env2"
[ 0.544527] 0x000000100000-0x000000200000 : "jffs"
[ 0.552249] 0x000000200000-0x000000300000 : "jffs2"
[ 0.560216] 0x000000300000-0x000000fe0000 : "firmware"
[ 0.569086] 2 uimage-fw partitions found on MTD device firmware
[ 0.575761] Creating 2 MTD partitions on "firmware":
[ 0.581292] 0x000000000000-0x000000720000 : "kernel"
[ 0.589278] 0x000000720000-0x000000ce0000 : "rootfs"
[ 0.597242] mtd: setting mtd7 (rootfs) as root device
[ 0.602937] mtdsplit: no squashfs found in "rootfs"
[ 0.608516] 0x000000fe0000-0x000001000000 : "log"
[ 0.627698] Probing RTL838X eth device pdev: 818a9400, dev: 818a9410
[ 0.654047] Found SoC ID: 9302: RTL9302B, family 9300
[ 0.659842] Using MAC 000000e04c000000
[ 0.664056] set sds port 0 to 2
[ 0.667633] set sds port 24 to 6
[ 0.671229] set sds port 25 to 7
[ 0.674851] set sds port 26 to 8
[ 0.678444] set sds port 27 to 9
[ 0.682823] c45_mask: 000e0000
[ 0.824719] thermal thermal_zone0: Failed to set trips: -34
[ 0.861080] thermal thermal_zone1: Failed to set trips: -34
[ 0.897444] thermal thermal_zone2: Failed to set trips: -34
[ 0.916104] REALTEK RTL9300 SERDES mdio-bus:1b: Detected internal RTL9300 Serdes
[ 0.933675] i2c_dev: i2c /dev entries driver
[ 0.938752] rtl9300_i2c_probe probing I2C adapter
[ 0.944030] i2c-rtl9300 1b00036c.i2c-rtl9300: SCL speed 100000, mode is 0
[ 0.951641] rtl9300_i2c_probe scl_num 0
[ 0.955942] rtl9300_i2c_probe sda_num 1
[ 0.964265] NET: Registered PF_INET6 protocol family
[ 0.983832] Segment Routing with IPv6
[ 0.988131] In-situ OAM (IOAM) with IPv6
[ 0.992702] NET: Registered PF_PACKET protocol family
[ 0.998457] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.013560] 8021q: 802.1Q VLAN Support v1.8
[ 1.041418] sfp sfp-p12: Host maximum power 1.0W
[ 1.295351] REALTEK RTL9300 SERDES rtl838x slave mii-0:1b: Detected internal RTL9300 Serdes
[ 1.316775] REALTEK RTL9300 SERDES rtl838x slave mii-0:3f: Detected internal RTL9300 Serdes
[ 1.336285] rtl93xx_setup called
[ 1.339933] In rtl83xx_vlan_setup
[ 1.343615] In rtl930x_vlan_profile_setup
[ 1.348125] In rtl930x_vlan_profile_setup
[ 1.352589] UNKNOWN_MC_PMASK: 000000001fffffff
[ 1.357556] VLAN 0: L2 learn: 0; Unknown MC PMasks: L2 1fffffff, IPv4 1fffffff, IPv6: 1fffffff
[ 1.357576] Routing enabled: IPv4 UC y, IPv6 UC y, IPv4 MC y, IPv6 MC y
[ 1.374734] Bridge enabled: IPv4 MC n, IPv6 MC n,
[ 1.380162] VLAN profile 0: raw 00033000 00000000 1fffffff 1fffffff 1fffffff
[ 2.414200] rtl83xx_enable_phy_polling: f0000ff
[ 2.420126] rtl930x_pie_init
[ 2.423534] rtl930x_led_init called
[ 2.427538] rtl930x_led_init led_set configuration invalid skipping over this set
[ 2.435921] rtl930x_led_init bb00cc00: 01052659
[ 2.440959] rtl930x_led_init bb00cc04: aaaa5555
[ 2.446017] rtl930x_led_init bb00cc08: 007faaaa
[ 2.451061] rtl930x_led_init bb00cc0c: 00000000
[ 2.456119] rtl930x_led_init bb00cc10: 00000000
[ 2.461155] rtl930x_led_init bb00cc14: 00000000
[ 2.466212] rtl930x_led_init bb00cc18: 0a200a01
[ 2.471258] rtl930x_led_init bb00cc1c: 0a0b0a28
[ 2.476315] rtl930x_led_init bb00cc20: 0a820a0b
[ 2.481361] rtl930x_led_init bb00cc24: 00000000
[ 2.486418] rtl930x_led_init bb00cc28: 0a200b80
[ 2.491463] rtl930x_led_init bb00cc2c: 00000000
[ 2.496520] rtl930x_led_init bb00cc30: 00950000
[ 2.501565] rtl930x_led_init bb00cc34: 00000000
[ 2.506622] rtl930x_led_init bb00cc38: 00950000
[ 2.511659] rtl930x_led_init bb00cc3c: 0f0000ff
[ 2.516724] rtl930x_led_init bb00cc40: 0f0000ff
[ 2.521770] rtl930x_led_init bb00cc44: 0f0000ff
[ 2.526830] rtl930x_led_init bb00cc48: 00000000
[ 2.531873] rtl930x_led_init bb00cc4c: 00000000
[ 2.536930] rtl930x_led_init bb00cc50: 00000000
[ 2.541967] rtl930x_led_init bb00cc54: 00000000
[ 2.547024] rtl930x_led_init bb00cc58: 00000000
[ 2.552060] rtl930x_led_init bb00cc5c: 00000000
[ 2.557280] rtl83xx-switch switch@1b000000: configuring for fixed/internal link mode
[ 2.565971] rtl93xx_phylink_mac_config port 28, mode 1, phy-mode: internal, speed -1, link 0
[ 2.576108] rtl83xx-switch switch@1b000000 lan1 (uninitialized): PHY [mdio-bus:00] driver [REALTEK RTL8218D] (irq=POLL)
[ 2.589958] rtl83xx-switch switch@1b000000 lan2 (uninitialized): PHY [mdio-bus:01] driver [REALTEK RTL8218D] (irq=POLL)
[ 2.603781] rtl83xx-switch switch@1b000000 lan3 (uninitialized): PHY [mdio-bus:02] driver [REALTEK RTL8218D] (irq=POLL)
[ 2.618261] rtl83xx-switch switch@1b000000 lan4 (uninitialized): PHY [mdio-bus:03] driver [REALTEK RTL8218D] (irq=POLL)
[ 2.632072] rtl83xx-switch switch@1b000000 lan5 (uninitialized): PHY [mdio-bus:04] driver [REALTEK RTL8218D] (irq=POLL)
[ 2.645942] rtl83xx-switch switch@1b000000 lan6 (uninitialized): PHY [mdio-bus:05] driver [REALTEK RTL8218D] (irq=POLL)
[ 2.659755] rtl83xx-switch switch@1b000000 lan7 (uninitialized): PHY [mdio-bus:06] driver [REALTEK RTL8218D] (irq=POLL)
[ 2.673578] rtl83xx-switch switch@1b000000 lan8 (uninitialized): PHY [mdio-bus:07] driver [REALTEK RTL8218D] (irq=POLL)
[ 2.690213] rtl83xx-switch switch@1b000000: Link is Up - 10Gbps/Full - flow control off
[ 2.722084] rtl83xx-switch switch@1b000000 lan9 (uninitialized): PHY [mdio-bus:18] driver [Aquantia AQR113C] (irq=POLL)
[ 2.754558] rtl83xx-switch switch@1b000000 lan10 (uninitialized): PHY [mdio-bus:19] driver [Aquantia AQR113C] (irq=POLL)
[ 2.784924] rtl83xx-switch switch@1b000000 lan11 (uninitialized): PHY [mdio-bus:1a] driver [Aquantia AQR113C] (irq=POLL)
[ 2.800019] rtl838x-eth 1b00a300.ethernet eth0: entered promiscuous mode
[ 2.807716] DSA: tree 0 setup
[ 2.811102] LINK state irq: 23
[ 2.814591] In rtl83xx_setup_qos
[ 2.818250] L3_IPUC_ROUTE_CTRL 00002000, IPMC_ROUTE 0000077e, IP6UC_ROUTE 00014400, IP6MC_ROUTE 0001db7e
[ 2.828835] L3_IPUC_ROUTE_CTRL 00002001, IPMC_ROUTE 00000501, IP6UC_ROUTE 00014581, IP6MC_ROUTE 00012881
[ 2.839410] L3_IP_ROUTE_CTRL 0000013f
[ 2.843603] rtl930x_dbgfs_init called
[ 2.848652] rtl83xx_fib_event_work_do: FIB4 default rule failed
[ 2.857360] rtl83xx_fib_event_work_do: FIB4 default rule failed
[ 2.865060] clk: Disabling unused clocks
[ 2.871256] List of all partitions:
[ 2.875232] 0100 4096 ram0
[ 2.875249] (driver?)
[ 2.882023] 0101 4096 ram1
[ 2.882032] (driver?)
[ 2.888836] 0102 4096 ram2
[ 2.888851] (driver?)
[ 2.895651] 0103 4096 ram3
[ 2.895666] (driver?)
[ 2.902438] 0104 4096 ram4
[ 2.902448] (driver?)
[ 2.909252] 0105 4096 ram5
[ 2.909267] (driver?)
[ 2.916066] 0106 4096 ram6
[ 2.916082] (driver?)
[ 2.922854] 0107 4096 ram7
[ 2.922863] (driver?)
[ 2.929668] 0108 4096 ram8
[ 2.929683] (driver?)
[ 2.936482] 0109 4096 ram9
[ 2.936498] (driver?)
[ 2.943268] 010a 4096 ram10
[ 2.943277] (driver?)
[ 2.950179] 010b 4096 ram11
[ 2.950194] (driver?)
[ 2.957105] 010c 4096 ram12
[ 2.957120] (driver?)
[ 2.963983] 010d 4096 ram13
[ 2.963992] (driver?)
[ 2.970893] 010e 4096 ram14
[ 2.970908] (driver?)
[ 2.977810] 010f 4096 ram15
[ 2.977824] (driver?)
[ 2.984722] 1f00 896 mtdblock0
[ 2.984737] (driver?)
[ 2.991991] 1f01 64 mtdblock1
[ 2.992000] (driver?)
[ 2.999287] 1f02 64 mtdblock2
[ 2.999302] (driver?)
[ 3.006585] 1f03 1024 mtdblock3
[ 3.006601] (driver?)
[ 3.013854] 1f04 1024 mtdblock4
[ 3.013864] (driver?)
[ 3.021151] 1f05 13184 mtdblock5
[ 3.021166] (driver?)
[ 3.028455] 1f06 7296 mtdblock6
[ 3.028470] (driver?)
[ 3.035752] 1f07 5888 mtdblock7
[ 3.035768] (driver?)
[ 3.043021] 1f08 128 mtdblock8
[ 3.043031] (driver?)
[ 3.050315] No filesystem could mount root, tried:
[ 3.050325] squashfs
[ 3.055765]
[ 3.059935] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,7)
[ 3.069222] Rebooting in 1 seconds..
Thanks for help.