[ 0.000000] Linux version 5.4.188 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16554-1d4dea6d4f)) #0 Sat Apr 16 12:59:34 2022
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Wavlink WL-WN530HG4
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] Normal zone: 144 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.000000] Writing ErrCtl register=0004b234
[ 0.000000] Readback ErrCtl register=0004b234
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 54552K/65536K available (5071K kernel code, 204K rwdata, 632K rodata, 4132K init, 213K bss, 10984K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] random: get_random_bytes called from 0x805c7a28 with crng_init=0
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000009] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015501] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
[ 0.059575] pid_max: default: 32768 minimum: 301
[ 0.068964] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.083379] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.105762] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.125066] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.138677] pinctrl core: initialized pinctrl subsystem
[ 0.150525] NET: Registered protocol family 16
[ 0.417345] PCI host bridge /pcie@10140000 ranges:
[ 0.426748] MEM 0x0000000020000000..0x000000002fffffff
[ 0.437118] IO 0x0000000010160000..0x000000001016ffff
[ 0.470296] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.481359] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.494550] PCI host bridge to bus 0000:00
[ 0.502609] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[ 0.516224] pci_bus 0000:00: root bus resource [io 0x10160000-0x1016ffff]
[ 0.529896] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.543396] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.559195] pci 0000:00:00.0: [1814:0801] type 01 class 0x060400
[ 0.571125] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 0.583554] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 0.596097] pci 0000:00:00.0: supports D1
[ 0.603977] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.617484] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.633536] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[ 0.645433] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 0.658892] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.672295] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.686181] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.699239] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[ 0.712390] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 0.725511] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 0.739360] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[ 0.752863] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
[ 0.767228] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[ 0.780739] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
[ 0.795286] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
[ 0.809626] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.819492] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
[ 0.832990] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref]
[ 0.852465] clocksource: Switched to clocksource systick
[ 0.864116] thermal_sys: Registered thermal governor 'step_wise'
[ 0.864631] NET: Registered protocol family 2
[ 0.885306] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.900544] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.917071] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.932287] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.946294] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.959075] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.971986] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.986090] NET: Registered protocol family 1
[ 0.994719] PCI: CLS 0 bytes, default 32
[ 1.484452] random: fast init done
[ 6.634557] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 6.648605] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[ 6.670081] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 6.681598] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 6.717430] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 6.735209] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 6.750876] printk: console [ttyS0] disabled
[ 6.759354] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 6.778997] printk: console [ttyS0] enabled
[ 6.795573] printk: bootconsole [early0] disabled
[ 6.823686] spi spi0.0: force spi mode3
[ 6.834235] spi-nor spi0.0: gd25q64 (8192 Kbytes)
[ 6.843695] 4 fixed-partitions partitions found on MTD device spi0.0
[ 6.856367] Creating 4 MTD partitions on "spi0.0":
[ 6.865928] 0x000000000000-0x000000030000 : "u-boot"
[ 6.877090] 0x000000030000-0x000000040000 : "config"
[ 6.888192] 0x000000040000-0x000000050000 : "factory"
[ 6.899436] 0x000000050000-0x000000800000 : "firmware"
[ 6.940358] gsw: setting port4 to ephy mode
[ 6.973126] mtk_soc_eth 10100000.ethernet: connected port 5 to PHY at mdio-bus:05 [uid=001cc916, driver=Generic PHY]
[ 6.994384] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 7.006927] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 7.023988] rt2880_wdt 10000120.watchdog: Initialized
[ 7.035783] NET: Registered protocol family 10
[ 7.049690] Segment Routing with IPv6
[ 7.057224] NET: Registered protocol family 17
[ 7.066180] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 7.092029] 8021q: 802.1Q VLAN Support v1.8
[ 7.125381] Freeing unused kernel memory: 4132K
[ 7.134455] This architecture does not have kernel memory protection.
[ 7.147292] Run /init as init process
[ 7.736906] init: Console is alive
[ 7.744037] init: - watchdog -
[ 7.773989] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 7.793056] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 7.812596] init: - preinit -
[ 8.072938] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.176320] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.416974] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.830820] 8021q: adding VLAN 0 to HW filter on device eth0
[ 10.376584] procd: - early -
[ 10.382630] procd: - watchdog -
[ 10.636011] procd: - watchdog -
[ 10.642805] procd: - ubus -
[ 10.658267] urandom_read: 5 callbacks suppressed
[ 10.658277] random: ubusd: uninitialized urandom read (4 bytes read)
[ 10.688153] random: ubusd: uninitialized urandom read (4 bytes read)
[ 10.705069] procd: - init -
[ 11.412922] kmodloader: loading kernel modules from /etc/modules.d/*
[ 11.467810] Loading modules backported from Linux version v5.10.110-0-g3238bffaf992
[ 11.483162] Backport generated by backports.git v5.10.110-1-0-g1fbde860
[ 11.568504] xt_time: kernel timezone is -0000
[ 11.721922] PPP generic driver version 2.4.2
[ 11.746939] NET: Registered protocol family 24
[ 11.834292] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[ 11.848737] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[ 11.864212] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 11.878036] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 11.914513] urngd: jent-rng init failed, err: 2
[ 11.950431] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 19.204376] crng init done
[ 33.062382] mtk_soc_eth 10100000.ethernet eth0: port 3 link up (10Mbps/Full duplex)
[ 34.445767] mtk_soc_eth 10100000.ethernet eth0: port 3 link down
[ 37.115468] mtk_soc_eth 10100000.ethernet eth0: port 3 link up (100Mbps/Full duplex)
[ 84.968284] 8021q: adding VLAN 0 to HW filter on device eth0
[ 85.005882] br-lan: port 1(eth0.1) entered blocking state
[ 85.016739] br-lan: port 1(eth0.1) entered disabled state
[ 85.027936] device eth0.1 entered promiscuous mode
[ 85.037538] device eth0 entered promiscuous mode
[ 85.118938] br-lan: port 1(eth0.1) entered blocking state
[ 85.129773] br-lan: port 1(eth0.1) entered forwarding state
[ 85.980870] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 120.862754] mtk_soc_eth 10100000.ethernet eth0: port 3 link down
[ 120.877292] br-lan: port 1(eth0.1) entered disabled state
[ 192.931146] mtk_soc_eth 10100000.ethernet eth0: port 3 link up (10Mbps/Full duplex)
[ 192.948044] br-lan: port 1(eth0.1) entered blocking state
[ 192.958881] br-lan: port 1(eth0.1) entered forwarding state
[ 193.675575] mtk_soc_eth 10100000.ethernet eth0: port 3 link down
[ 193.690016] br-lan: port 1(eth0.1) entered disabled state
[ 195.260913] mtk_soc_eth 10100000.ethernet eth0: port 3 link up (100Mbps/Full duplex)
[ 195.277089] br-lan: port 1(eth0.1) entered blocking state
[ 195.287908] br-lan: port 1(eth0.1) entered forwarding state