Would resummoning a Pogoplug V4 (kirkwood) be of help? Alike Sheevaplug. Could probably try within a week.
1 Like
Is OpenWRT going to use Kernel 6 in the future?
In the future, sure (as in v6.1), but not for 23.xy.z.
yes, after doing the release
I have mounted an usb drive and a SD card and both work fine. Installed luci and a few other packages and that works without issues as well. No errors in dmesg so 5.15 seems to work OK on the sheevaplug / kirkwood.
1 Like
For what it's worth, I'm in the process of adding a new Kirkwood target and can confirm that the 5.15 kernel is running with similar performance and compatibility to the 5.10 kernel.
1 Like
I've pulled the April 9 snapshot for kirkwood, it's 5.15 kernel. Installed on EA3500 and running similar to openwrt v21.
Willing tester, but wanted to clear up something about this upgrade.
Running (kirkwood) on e4200-v2 and ea4500-v1
Currently stuck on 21.02.5 r16688-fa9a932fdb due to a bug
Willing to test on spare device ,
And just wanted to clarify the situation of sysupgrading or factory to 23.X .
Last time i had issues with flashing 22.X from a primary active partition which ran 21.02.x
flashing just would not take. only when switching to secondary active was i able to flash
22.03.3 to primary .
And now for the main question which involves
Sun Apr 9 23:06:44 EDT 2023 upgrade: The device is supported, but this image is incompatible for sysupgrade based on the image version (1.1->2.0). Sun Apr 9 23:06:44 EDT 2023 upgrade: Partition design has changed compared to older versions (up to 21.02) due to kernel size restrictions. Upgrade via sysupgrade mechanism is not possible, so new installation via factory style image is required. Image check failed.
What would this do to keeping 21.X version on another partition?
Any foreseeable problems with later sysupgrades to that partition?
I guess real question is is there any issues to flashing to this new partition table and
keeping older version arround also . I use a spare device for testing before
implementing any new updates/configs on main device. So i need one partition to
have same version as as the other main devices (e4200/ea4500)
thanx
You have to flash the factory image. As far as i know this should be possible on either partition. You can keep 1 partition with the old layout if you like. Be aware if you restore settings from a backup then there is a setting somewhere that it still indicates that it's the old layout, so you have to change that manually.
Note having that multi boot addon can help show which version is where!
r22549-9cbc83726e on ea4500 (kirkwood)
minicom boot logs looked clean.
few hours of testing (ipv4 only lan/wan)
br-lan does not act as hub unlike in 22.3(so assume fixed)
wish it was fixed in 22.X also so i would not have to jump
over 22.x on these devices from 21.x to 23.x
ss should probably be available by default next to netstat. like ip is next to ifconfig.
And ss -lput ipv6 wildcards look like ipv4s , unlike netstats which you can tell apart.
initial opkg install of luci does not seem have https .
and i do not remeber luci-theme-openwrt bringing in 10 more
packages before , seem important to luci itself
like lua,luci-lib-ip,liblucihttp-lua,luci-lib-base,lububus-lua etc...
(seems like packages luci install should have brought in?)
iperf tests seem normal 312 Mbits each way lan-wan at 100% cpu load (long runs)
software based offloading seems to break networking (only icmps get trough)
some leakage of https(maybe others) packets to lan ports of active connections when
android client switches from radio0 to radio1. but ive seen that before when in similar
circumstances when a host is just unplugged with active connections .
usb mounts , and rsyslog seems to log to usb just fine.
wish there was a system /etc/cron.d/ for services like logrotate to plug their own files in to
instead of manually adding to roots crontab.
should rsyslog be a listening server in default config?
#vim
E1187: Failed to source defaults.vim
Press ENTER or type command to continue
radio0-1 seem to work like before
with usual bugs like a few old phones connect but arps wont go trough so no ip connection.
dnsmasq should probably be changed to listen on wildcard by default.
maybe disable on internet, but all other services are on wildcards which are then firewalled .
so why bother have it bind to separate interfaces if services like ssh and http listen on wildcard?
otherwise netstat and ss outputs are a mess.
uci config takeover of rsyslog and others (dnsmasq) , just wish there was a
clear way to just use a single non merged config (by choice).
Say an option to disable ucis involvement in a service.
Otherwise you have to 3 way check to see what settings came from where.
And in some cases it is much easier to manage non uci configs,
like say complex dnsmasq setup with its own dhcp-hosts addn-hosts files etc..
maybe look in to dhcp-hosts addn-hosts format files for statistics in luci even when
dnsmasq is not running ( on dumb aps i have to replicate those files in to a new format
uci or ethers files to get the names of clients based on macs when there is no
layer3 connectivity just a layer2 vlan)
disclaimer: my opinions only, should not be considered as criticism of any kind.
2 Likes
Thank you a lot for the elaborate test report!
That's a bit worrying and we should check what's going on there.... Most likely it will also affect other hardware/targets and not only kirkwood.
1 Like
also i never liked it when, enabling vlan filtering the menu extended in luci.
should be enough room to fit all of that info,
and i think old build 19.x pre DSA did not have this problem
edit:
ps: software flow offloading was lan-wan breakage (think lan-lan,lan-device was ok)
PS: also if there is a need for some specific tests/retests please post , i will keep this extra device
with snapshot installed on extra partition.
ReadyNAS Duo v2
2x WD60EFRX
14TB and (uh) 8TB external SCSI disks on the USB3 ports
Running Samba, backup server.
I downloaded the imagebuilder snapshot 21 April, built the image for my system, sysupgraded it and went to town. I was in the midst of a md resync, which has continued after reboot.
I'll run the usual backups to the box, copy large files on the USB disks, and generally scowl at it for a day or so. Then I'll see if I have any more luck with the WD140EFGX in it than I have on 22.03.4 (which is to say, very little).
Thanks -
Dana
dmesg output:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.15.107 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 12.2.0 r22604-a247f49794) 12.2.0, GNU ld (GNU Binutils) 2.40.0) #0 Thu Apr 20 12:23:04 2023
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] OF: fdt: Machine model: NETGEAR ReadyNAS Duo v2
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk reason=normal mtdparts=nand_mtd:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x1000000@0x800000(minirootfs),0x6800000@0x1800000(jffs2);
[ 0.000000] Unknown kernel command line parameters "earlyprintk reason=normal", will be passed to user space.
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 249500K/262144K available (6316K kernel code, 586K rwdata, 1632K rodata, 1024K init, 217K bss, 12644K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000001] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.000029] Switching to timer-based delay loop, resolution 5ns
[ 0.000150] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
[ 0.000176] pid_max: default: 32768 minimum: 301
[ 0.000356] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.000382] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.001129] CPU: Testing write buffer coherency: ok
[ 0.002260] Setting up static identity map for 0x100000 - 0x10003c
[ 0.002456] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1
[ 0.002629] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.005439] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.005469] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.005580] pinctrl core: initialized pinctrl subsystem
[ 0.006784] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.007124] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.007926] thermal_sys: Registered thermal governor 'step_wise'
[ 0.008000] cpuidle: using governor ladder
[ 0.008266] Feroceon L2: Enabling L2
[ 0.008300] Feroceon L2: Cache support initialised.
[ 0.013242] No ATAGs?
[ 0.018226] SCSI subsystem initialized
[ 0.018378] libata version 3.00 loaded.
[ 0.018543] usbcore: registered new interface driver usbfs
[ 0.018585] usbcore: registered new interface driver hub
[ 0.018624] usbcore: registered new device driver usb
[ 0.019454] clocksource: Switched to clocksource orion_clocksource
[ 0.020075] NET: Registered PF_INET protocol family
[ 0.020221] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.020762] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.020795] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.020811] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.020844] TCP bind hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.020875] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.020937] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.020963] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.021125] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.021156] PCI: CLS 0 bytes, default 32
[ 0.022506] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.025926] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.025944] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.026545] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.028745] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 0.029704] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges:
[ 0.029745] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[ 0.029770] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1044000..0x00f1045fff -> 0x0000044000
[ 0.029796] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1080000..0x00f1081fff -> 0x0000080000
[ 0.029819] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 0.029839] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 0.029859] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 0.029875] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 0.030031] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[ 0.030046] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.030061] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[ 0.030074] pci_bus 0000:00: root bus resource [mem 0xf1044000-0xf1045fff] (bus address [0x00044000-0x00045fff])
[ 0.030087] pci_bus 0000:00: root bus resource [mem 0xf1080000-0xf1081fff] (bus address [0x00080000-0x00081fff])
[ 0.030098] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[ 0.030109] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 0.030183] pci 0000:00:01.0: [11ab:6282] type 01 class 0x060400
[ 0.031068] PCI: bus0: Fast back to back transfers disabled
[ 0.031083] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.031204] pci 0000:01:00.0: [1033:0194] type 00 class 0x0c0330
[ 0.031242] pci 0000:01:00.0: reg 0x10: [mem 0x40000000-0x40001fff 64bit]
[ 0.031381] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.031418] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 0.032274] PCI: bus1: Fast back to back transfers disabled
[ 0.032288] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.032434] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe00fffff]
[ 0.032453] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe0001fff 64bit]
[ 0.032475] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.032488] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff]
[ 0.032538] pci 0000:00:01.0: enabling device (0140 -> 0142)
[ 0.038058] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.039332] printk: console [ttyS0] disabled
[ 0.039413] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A
[ 0.724032] printk: console [ttyS0] enabled
[ 0.728718] Loading iSCSI transport class v2.0-870.
[ 0.737494] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it
[ 0.746251] ONFI parameter recovery failed, aborting
[ 0.751257] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 0.757635] nand: Hynix NAND 128MiB 3,3V 8-bit
[ 0.762099] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.769732] Scanning device for bad blocks
[ 0.850690] mtd: no mtd-id
[ 0.853438] 4 fixed-partitions partitions found on MTD device orion_nand
[ 0.860176] Creating 4 MTD partitions on "orion_nand":
[ 0.865339] 0x000000000000-0x000000180000 : "u-boot"
[ 0.872275] 0x000000180000-0x0000001a0000 : "u-boot-env"
[ 0.878047] 0x000000200000-0x000000800000 : "kernel"
[ 0.884438] 0x000000800000-0x000008000000 : "ubi"
[ 0.900461] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 0.910397] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address e0:46:9a:a0:94:e0
[ 1.929458] rtc-mv f1010300.rtc: internal RTC not ticking
[ 1.934964] i2c_dev: i2c /dev entries driver
[ 1.940567] orion_wdt: Initial timeout 21 sec
[ 1.953677] marvell-cesa f1030000.crypto: CESA device successfully registered
[ 1.961549] NET: Registered PF_INET6 protocol family
[ 1.968172] Segment Routing with IPv6
[ 1.971934] In-situ OAM (IOAM) with IPv6
[ 1.975933] NET: Registered PF_PACKET protocol family
[ 1.981067] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.994212] 8021q: 802.1Q VLAN Support v1.8
[ 2.002189] UBI: auto-attach mtd3
[ 2.005534] ubi0: attaching mtd3
[ 2.151057] ubi0: scanning is finished
[ 2.165452] ubi0: attached mtd3 (name "ubi", size 120 MiB)
[ 2.170996] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[ 2.177905] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[ 2.184651] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
[ 2.191482] ubi0: good PEBs: 960, bad PEBs: 0, corrupted PEBs: 0
[ 2.197516] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 2.204779] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 488173503
[ 2.213873] ubi0: available PEBs: 0, total reserved PEBs: 960, PEBs reserved for bad PEB handling: 20
[ 2.223372] ubi0: background thread "ubi_bgt0d" started, PID 249
[ 2.230116] block ubiblock0_0: created from ubi0:0(rootfs)
[ 2.235632] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 2.248399] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 2.258480] Freeing unused kernel image (initmem) memory: 1024K
[ 2.264655] Run /sbin/init as init process
[ 2.268768] with arguments:
[ 2.268771] /sbin/init
[ 2.268775] earlyprintk
[ 2.268778] with environment:
[ 2.268781] HOME=/
[ 2.268784] TERM=linux
[ 2.268787] reason=normal
[ 2.544359] init: Console is alive
[ 2.547950] init: - watchdog -
[ 3.059729] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.116797] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.127762] fsl-ehci: Freescale EHCI Host controller driver
[ 3.135853] ehci-orion: EHCI orion driver
[ 3.140045] orion-ehci f1050000.ehci: EHCI Host Controller
[ 3.145583] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 3.153389] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000
[ 3.179496] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 3.185979] hub 1-0:1.0: USB hub found
[ 3.190297] hub 1-0:1.0: 1 port detected
[ 3.197073] ehci-platform: EHCI generic platform driver
[ 3.209227] sata_mv f1080000.sata: version 1.28
[ 3.209581] sata_mv f1080000.sata: slots 32 ports 2
[ 3.218683] scsi host0: sata_mv
[ 3.222938] scsi host1: sata_mv
[ 3.226222] ata1: SATA max UDMA/133 irq 33
[ 3.230370] ata2: SATA max UDMA/133 irq 33
[ 3.729467] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 3.740224] ata1.00: ATA-9: WDC WD60EFRX-68L0BN1, 82.00A82, max UDMA/133
[ 3.746959] ata1.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 3.758439] ata1.00: configured for UDMA/133
[ 3.763000] scsi 0:0:0:0: Direct-Access ATA WDC WD60EFRX-68L 0A82 PQ: 0 ANSI: 5
[ 3.772128] sd 0:0:0:0: [sda] 11721045168 512-byte logical blocks: (6.00 TB/5.46 TiB)
[ 3.780023] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 3.786104] sd 0:0:0:0: [sda] Write Protect is off
[ 3.790945] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.791030] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.860576] sda: sda1
[ 3.863682] sd 0:0:0:0: [sda] Attached SCSI disk
[ 4.279467] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 4.290241] ata2.00: ATA-9: WDC WD60EFRX-68L0BN1, 82.00A82, max UDMA/133
[ 4.296989] ata2.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 4.308466] ata2.00: configured for UDMA/133
[ 4.313015] scsi 1:0:0:0: Direct-Access ATA WDC WD60EFRX-68L 0A82 PQ: 0 ANSI: 5
[ 4.322085] sd 1:0:0:0: [sdb] 11721045168 512-byte logical blocks: (6.00 TB/5.46 TiB)
[ 4.329980] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 4.335922] sd 1:0:0:0: [sdb] Write Protect is off
[ 4.340755] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 4.340838] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.408620] sdb: sdb1
[ 4.411741] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 4.419123] rtc-rs5c372 0-0032: rs5c372a found, 24hr
[ 4.431304] rtc-rs5c372 0-0032: registered as rtc0
[ 4.437905] rtc-rs5c372 0-0032: setting system clock to 2023-04-22T01:41:05 UTC (1682127665)
[ 4.453378] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 4.458676] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[ 4.466367] xhci_hcd 0000:01:00.0: hcc params 0x014042cb hci version 0x96 quirks 0x0000000000000004
[ 4.475682] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 4.480963] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3
[ 4.488402] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[ 4.495449] hub 2-0:1.0: USB hub found
[ 4.499717] hub 2-0:1.0: 2 ports detected
[ 4.504132] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.513086] hub 3-0:1.0: USB hub found
[ 4.517294] hub 3-0:1.0: 2 ports detected
[ 4.528880] usbcore: registered new interface driver usb-storage
[ 4.538638] usbcore: registered new interface driver uas
[ 4.546337] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.556048] init: - preinit -
[ 5.231786] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.315769] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.336780] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.484333] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 5.494249] mv643xx_eth_port mv643xx_eth_port.0 eth0: link down
[ 5.649661] usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
[ 5.695602] scsi host2: uas
[ 5.699884] scsi 2:0:0:0: Direct-Access Seagate Expansion HDD 1801 PQ: 0 ANSI: 6
[ 5.710441] sd 2:0:0:0: [sdc] Spinning up disk...
[ 6.049462] usb 2-2: new high-speed USB device number 3 using xhci_hcd
[ 6.257056] hub 2-2:1.0: USB hub found
[ 6.261449] hub 2-2:1.0: 3 ports detected
[ 6.399709] usb 3-2: new SuperSpeed USB device number 3 using xhci_hcd
[ 6.437129] hub 3-2:1.0: USB hub found
[ 6.441450] hub 3-2:1.0: 3 ports detected
[ 6.729458] .
[ 7.400411] usb 2-2-port2: Cannot enable. Maybe the USB cable is bad?
[ 7.671493] mount_root: loading kmods from internal overlay
[ 7.693245] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 7.701795] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 7.786396] .
[ 8.051922] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 8.084287] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 472
[ 8.190973] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 8.198857] UBIFS (ubi0:1): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 8.208861] UBIFS (ubi0:1): FS size: 103864320 bytes (99 MiB, 805 LEBs), max 816 LEBs, journal size 5160960 bytes (4 MiB, 40 LEBs)
[ 8.220667] UBIFS (ubi0:1): reserved for root: 4905768 bytes (4790 KiB)
[ 8.227310] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 0D51F39B-BF69-48B5-858D-4073A6F5C69C, small LPT model
[ 8.239156] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 8.246340] block: unable to load configuration (fstab: Entry not found)
[ 8.253194] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 8.259801] block: unable to load configuration (fstab: Entry not found)
[ 8.266611] block: attempting to load /etc/config/fstab
[ 8.273579] block: unable to load configuration (fstab: Entry not found)
[ 8.280424] block: no usable configuration
[ 8.289894] UBIFS (ubi0:1): un-mount UBI device 0
[ 8.294636] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[ 8.304848] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 8.335919] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 475
[ 8.442621] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 8.450522] UBIFS (ubi0:1): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 8.460490] UBIFS (ubi0:1): FS size: 103864320 bytes (99 MiB, 805 LEBs), max 816 LEBs, journal size 5160960 bytes (4 MiB, 40 LEBs)
[ 8.472318] UBIFS (ubi0:1): reserved for root: 4905768 bytes (4790 KiB)
[ 8.478960] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 0D51F39B-BF69-48B5-858D-4073A6F5C69C, small LPT model
[ 8.541261] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 8.548380] block: unable to load configuration (fstab: Entry not found)
[ 8.555257] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 8.562419] block: unable to load configuration (fstab: Entry not found)
[ 8.569238] block: attempting to load /etc/config/fstab
[ 8.574637] block: unable to load configuration (fstab: Entry not found)
[ 8.581500] block: no usable configuration
[ 8.586256] mount_root: overlay filesystem has not been fully initialized yet
[ 8.594184] mount_root: switching to ubifs overlay
[ 8.889503] .
[ 8.910658] usb 3-2.1: new SuperSpeed USB device number 4 using xhci_hcd
[ 8.939846] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 9.016531] scsi host3: uas
[ 9.020850] scsi 3:0:0:0: Direct-Access Seagate Backup+ Hub BK D785 PQ: 0 ANSI: 6
[ 9.034110] procd: - early -
[ 9.037122] procd: - watchdog -
[ 9.651693] procd: - watchdog -
[ 9.655088] procd: - ubus -
[ 9.703779] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.714994] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.722921] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.731955] procd: - init -
[ 9.929506] .
[ 10.401398] kmodloader: loading kernel modules from /etc/modules.d/*
[ 10.448111] urngd: v1.0.2 started.
[ 10.500335] random: crng init done
[ 10.503763] random: 29 urandom warning(s) missed due to ratelimiting
[ 10.524444] sd 3:0:0:0: [sdd] Spinning up disk...
[ 10.969456] ......
[ 16.919460] usb 2-2.3: new full-speed USB device number 6 using xhci_hcd
[ 17.209456] .
[ 17.609455] .ready
[ 17.613657] sd 3:0:0:0: [sdd] 15628053167 512-byte logical blocks: (8.00 TB/7.28 TiB)
[ 17.621693] sd 3:0:0:0: [sdd] Write Protect is off
[ 17.626505] sd 3:0:0:0: [sdd] Mode Sense: 4f 00 00 00
[ 17.626727] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 17.636272] sd 3:0:0:0: [sdd] Optimal transfer size 33553920 bytes
[ 17.739544] sdd: sdd1
[ 17.745228] sd 3:0:0:0: [sdd] Attached SCSI disk
[ 18.249458] ....ready
[ 21.372534] sd 2:0:0:0: [sdc] 27344764927 512-byte logical blocks: (14.0 TB/12.7 TiB)
[ 21.380417] sd 2:0:0:0: [sdc] 4096-byte physical blocks
[ 21.385869] sd 2:0:0:0: [sdc] Write Protect is off
[ 21.390696] sd 2:0:0:0: [sdc] Mode Sense: 53 00 00 08
[ 21.391079] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 21.400744] sd 2:0:0:0: [sdc] Optimal transfer size 33553920 bytes not a multiple of physical block size (4096 bytes)
[ 21.528928] sdc: sdc1
[ 21.535132] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 21.572514] GACT probability on
[ 21.581910] Mirror/redirect action on
[ 21.610316] u32 classifier
[ 21.613043] input device check on
[ 21.616712] Actions configured
[ 21.711016] usbcore: registered new interface driver ums-alauda
[ 21.721723] usbcore: registered new interface driver ums-cypress
[ 21.733228] usbcore: registered new interface driver ums-datafab
[ 21.743623] usbcore: registered new interface driver ums-freecom
[ 21.752858] usbcore: registered new interface driver ums-isd200
[ 21.762301] usbcore: registered new interface driver ums-jumpshot
[ 21.771781] usbcore: registered new interface driver ums-karma
[ 21.781255] usbcore: registered new interface driver ums-sddr09
[ 21.791705] usbcore: registered new interface driver ums-sddr55
[ 21.801046] usbcore: registered new interface driver ums-usbat
[ 21.870450] xt_time: kernel timezone is -0000
[ 21.980812] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 23.474715] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: . Quota mode: disabled.
[ 25.870644] mtdblock: MTD device 'ubi' is NAND, please consider using UBI block devices instead.
[ 25.891308] mtdblock: MTD device 'kernel' is NAND, please consider using UBI block devices instead.
[ 25.910943] mtdblock: MTD device 'u-boot-env' is NAND, please consider using UBI block devices instead.
[ 25.930901] mtdblock: MTD device 'u-boot' is NAND, please consider using UBI block devices instead.
[ 25.989711] md: md127 stopped.
[ 26.071127] md/raid1:md127: active with 1 out of 2 mirrors
[ 26.119612] md127: detected capacity change from 0 to 11720778880
[ 26.126527] md: recovery of RAID array md127
[ 26.248011] mtdblock: MTD device 'ubi' is NAND, please consider using UBI block devices instead.
[ 26.268121] mtdblock: MTD device 'kernel' is NAND, please consider using UBI block devices instead.
[ 26.284748] mtdblock: MTD device 'u-boot-env' is NAND, please consider using UBI block devices instead.
[ 26.302043] mtdblock: MTD device 'u-boot' is NAND, please consider using UBI block devices instead.
[ 29.145586] EXT4-fs (md127): recovery complete
[ 29.422540] EXT4-fs (md127): mounted filesystem with ordered data mode. Opts: . Quota mode: disabled.
[ 30.744435] br-lan: port 1(eth0) entered blocking state
[ 30.749752] br-lan: port 1(eth0) entered disabled state
[ 30.755248] device eth0 entered promiscuous mode
[ 37.522463] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control enabled
[ 37.539811] br-lan: port 1(eth0) entered blocking state
[ 37.545132] br-lan: port 1(eth0) entered forwarding state
[ 37.581125] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 41.980532] Adding 131068k swap on /vol/c/swapfile. Priority:-2 extents:2 across:132364k
- EA3500
- throughput issues on 100/10 connection with packet loss.
- not able to use sqm due to packet loss.
- problem authenticating password over 2.4GHz.
- upgraded from previous 22.03.2, no previous settings used manual config.
Editing My OP After a bit more investigating these issues the problem may have a been a problem with only IPv6, nothing to do with prefix length config just perhaps with my ISP.
I noticed this issue on 22.03.5 imagebuilder as well but only to find it to be a problem with my ISP as I didn't find packet loss or wan throughput on other test sites.
I can flash another snapshot image and run the EA3500 again to verify knowing what I know now.
Regards
onefreeman
Zyxel NSA310s (kirkwood), upgraded from 22.03, seems to work correctly on daily snapshot 1/05 with 5.15
2 Likes
Continuing daily use of ReadyNAS Duo v2 (kirkwood), upgrading md to Seagate ST12000VN0008 without issue.
I have a Check Point L-50 running OpenWRT 23.05.2.
This device was running OpenWRT since release 21 but I never got good iperf3 benchmarks at local cooper 1 Gbps connection.
I think that CPU not running at 1.2 Ghz. I saw something about a patch to overclock or ajust the frequency of this CPU. Someone successfull got this?
Follow some information:
root@ap-escritorio:~# cat /proc/cpuinfo
processor : 0
model name : Feroceon 88FR131 rev 1 (v5l)
BogoMIPS : 400.00
Features : swp half fastmult edsp
CPU implementer : 0x56
CPU architecture: 5TE
CPU variant : 0x2
CPU part : 0x131
CPU revision : 1
Hardware : Marvell Kirkwood (Flattened Device Tree)
Revision : 0000
Serial : 0000000000000000
root@ap-escritorio:~# lscpu
Architecture: armv5tel
Byte Order: Little Endian
CPU(s): 1
On-line CPU(s) list: 0
Vendor ID: Marvell
Model name: Feroceon-88FR131
Model: 1
Thread(s) per core: 1
Core(s) per socket: 1
Socket(s): 1
Stepping: 0x2
BogoMIPS: 400.00
Flags: swp half fastmult edsp
root@ap-escritorio:~# cat /proc/mtd
dev: size erasesize name
mtd0: 000c0000 00020000 "u-boot"
mtd1: 00040000 00020000 "bootldr-env"
mtd2: 07900000 00020000 "ubi"
mtd3: 00800000 00020000 "kernel-2"
mtd4: 07100000 00020000 "rootfs-2"
mtd5: 07900000 00020000 "default_sw"
mtd6: 01800000 00020000 "logs"
mtd7: 00100000 00020000 "preset_cfg"
mtd8: 00100000 00020000 "adsl"
mtd9: 07a00000 00020000 "storage"
root@ap-escritorio:~# fw_printenv
baudrate=115200
bootargs=console=ttyS0,115200
bootcmd=ubi part ubi; ubi read 0x800000 kernel; bootm 0x800000
bootdelay=1
dmz_mac_addr=00:1C:7F:<ommited>
dsl_mac_addr=A0:00:00:00:00:00
eth1addr=00:1C:7F:<ommited>
ethaddr=00:1C:7F:<ommited>
fdtcontroladdr=1fb1d948
fileaddr=800000
filesize=9d000
ipaddr=192.168.1.1
lan1_mac_addr=00:1C:7F:<ommited>
lan2_mac_addr=00:1C:7F:<ommited>
lan3_mac_addr=00:1C:7F:<ommited>
lan4_mac_addr=00:1C:7F:<ommited>
lan5_mac_addr=00:1C:7F:<ommited>
root@ap-escritorio:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.15.137 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 12.3.0 r23630-842932a63d) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 Tue Nov 14 13:38:11 2023
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] OF: fdt: Machine model: Check Point L-50
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920
[ 0.000000] Kernel command line: console=ttyS0,115200
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 509144K/524288K available (6238K kernel code, 586K rwdata, 980K rodata, 1024K init, 217K bss, 15144K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000001] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.000043] Switching to timer-based delay loop, resolution 5ns
[ 0.000219] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
[ 0.000256] CPU: Testing write buffer coherency: ok
[ 0.000370] pid_max: default: 32768 minimum: 301
[ 0.001541] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.001581] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.005085] Setting up static identity map for 0x100000 - 0x10003c
[ 0.005360] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[ 0.010490] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.010534] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.010826] pinctrl core: initialized pinctrl subsystem
[ 0.012860] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.013348] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.014568] thermal_sys: Registered thermal governor 'step_wise'
[ 0.014676] cpuidle: using governor ladder
[ 0.015003] Feroceon L2: Enabling L2
[ 0.015051] Feroceon L2: Cache support initialised.
[ 0.021848] No ATAGs?
[ 0.029699] SCSI subsystem initialized
[ 0.029930] libata version 3.00 loaded.
[ 0.030219] usbcore: registered new interface driver usbfs
[ 0.030274] usbcore: registered new interface driver hub
[ 0.030322] usbcore: registered new device driver usb
[ 0.031560] clocksource: Switched to clocksource orion_clocksource
[ 0.032844] NET: Registered PF_INET protocol family
[ 0.033105] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.034046] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.034088] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.034112] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.034168] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.034223] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.034327] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.034359] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.034661] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.034707] PCI: CLS 0 bytes, default 32
[ 0.036746] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.042462] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.042490] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.044393] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.046454] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 0.047796] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges:
[ 0.047851] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[ 0.047885] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 0.047909] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 0.048161] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[ 0.048182] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.048203] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[ 0.048220] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[ 0.048235] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 0.048377] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400
[ 0.049802] PCI: bus0: Fast back to back transfers disabled
[ 0.049822] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.051120] PCI: bus1: Fast back to back transfers enabled
[ 0.051137] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.051326] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.051867] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.053839] printk: console [ttyS0] disabled
[ 0.053936] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A
[ 0.592072] printk: console [ttyS0] enabled
[ 0.596985] Loading iSCSI transport class v2.0-870.
[ 0.606902] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xdc
[ 0.613329] nand: Samsung NAND 512MiB 3,3V 8-bit
[ 0.617970] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.625622] Scanning device for bad blocks
[ 0.680749] Bad eraseblock 669 at 0x0000053a0000
[ 0.786835] Bad eraseblock 2001 at 0x00000fa20000
[ 0.813016] Bad eraseblock 2283 at 0x000011d60000
[ 0.955865] 10 fixed-partitions partitions found on MTD device orion_nand
[ 0.962702] Creating 10 MTD partitions on "orion_nand":
[ 0.967952] 0x000000000000-0x0000000c0000 : "u-boot"
[ 0.975698] 0x0000000c0000-0x000000100000 : "bootldr-env"
[ 0.981773] 0x000000100000-0x000007a00000 : "ubi"
[ 0.988961] 0x000007a00000-0x000008200000 : "kernel-2"
[ 0.994776] 0x000008200000-0x00000f300000 : "rootfs-2"
[ 1.002341] 0x00000f300000-0x000016c00000 : "default_sw"
[ 1.008762] 0x000016c00000-0x000018400000 : "logs"
[ 1.015632] 0x000018400000-0x000018500000 : "preset_cfg"
[ 1.021645] 0x000018500000-0x000018600000 : "adsl"
[ 1.028398] 0x000018600000-0x000020000000 : "storage"
[ 1.054999] mv88e6085 f1072004.mdio-bus-mii:10: switch 0x1710 detected: Marvell 88E6171, revision 2
[ 1.210151] mv88e6085 f1072004.mdio-bus-mii:11: switch 0x1710 detected: Marvell 88E6171, revision 2
[ 1.352123] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 2.122492] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:1c:7f:<ommited>
[ 2.131806] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:1c:7f:<ommited>
[ 2.140793] i2c_dev: i2c /dev entries driver
[ 2.153342] orion_wdt: Initial timeout 21 sec
[ 2.171396] marvell-cesa f1030000.crypto: CESA device successfully registered
[ 2.179754] NET: Registered PF_INET6 protocol family
[ 2.187264] Segment Routing with IPv6
[ 2.191036] In-situ OAM (IOAM) with IPv6
[ 2.195088] NET: Registered PF_PACKET protocol family
[ 2.200228] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.213581] 8021q: 802.1Q VLAN Support v1.8
[ 2.227421] mv88e6085 f1072004.mdio-bus-mii:10: switch 0x1710 detected: Marvell 88E6171, revision 2
[ 3.461589] random: crng init done
[ 4.494597] mv88e6085 f1072004.mdio-bus-mii:11: configuring for fixed/rgmii-txid link mode
[ 4.508378] mv88e6085 f1072004.mdio-bus-mii:10: configuring for fixed/rgmii-txid link mode
[ 4.516867] mv88e6085 f1072004.mdio-bus-mii:11: Link is Up - 1Gbps/Full - flow control off
[ 4.529257] mv88e6085 f1072004.mdio-bus-mii:10: configuring for fixed/rgmii-id link mode
[ 4.539826] mv88e6085 f1072004.mdio-bus-mii:10: Link is Up - 1Gbps/Full - flow control off
[ 4.553869] mv88e6085 f1072004.mdio-bus-mii:10: Link is Up - 1Gbps/Full - flow control off
[ 4.570013] mv88e6085 f1072004.mdio-bus-mii:11 lan3 (uninitialized): PHY [mv88e6xxx-1:00] driver [Generic PHY] (irq=POLL)
[ 4.597408] mv88e6085 f1072004.mdio-bus-mii:11 lan8 (uninitialized): PHY [mv88e6xxx-1:01] driver [Generic PHY] (irq=POLL)
[ 4.621368] mv88e6085 f1072004.mdio-bus-mii:11 lan4 (uninitialized): PHY [mv88e6xxx-1:02] driver [Generic PHY] (irq=POLL)
[ 4.647461] mv88e6085 f1072004.mdio-bus-mii:11 dmz (uninitialized): PHY [mv88e6xxx-1:03] driver [Generic PHY] (irq=POLL)
[ 4.671943] mv88e6085 f1072004.mdio-bus-mii:10 lan5 (uninitialized): PHY [mv88e6xxx-2:00] driver [Generic PHY] (irq=POLL)
[ 4.697124] mv88e6085 f1072004.mdio-bus-mii:10 lan1 (uninitialized): PHY [mv88e6xxx-2:01] driver [Generic PHY] (irq=POLL)
[ 4.720997] mv88e6085 f1072004.mdio-bus-mii:10 lan6 (uninitialized): PHY [mv88e6xxx-2:02] driver [Generic PHY] (irq=POLL)
[ 4.741479] mv88e6085 f1072004.mdio-bus-mii:10 lan2 (uninitialized): PHY [mv88e6xxx-2:03] driver [Generic PHY] (irq=POLL)
[ 4.763048] mv88e6085 f1072004.mdio-bus-mii:10 lan7 (uninitialized): PHY [mv88e6xxx-2:04] driver [Generic PHY] (irq=POLL)
[ 4.775447] DSA: tree 0 setup
[ 4.778942] UBI: auto-attach mtd2
[ 4.782313] ubi0: attaching mtd2
[ 4.932652] ubi0: scanning is finished
[ 4.948058] ubi0: attached mtd2 (name "ubi", size 121 MiB)
[ 4.953616] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[ 4.960530] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[ 4.967281] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
[ 4.974123] ubi0: good PEBs: 967, bad PEBs: 1, corrupted PEBs: 0
[ 4.980158] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 4.987428] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 0
[ 4.995830] ubi0: available PEBs: 0, total reserved PEBs: 967, PEBs reserved for bad PEB handling: 79
[ 5.005416] ubi0: background thread "ubi_bgt0d" started, PID 387
[ 5.012786] block ubiblock0_1: created from ubi0:1(rootfs)
[ 5.018311] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 5.032126] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 5.042181] Freeing unused kernel image (initmem) memory: 1024K
[ 5.048159] Run /sbin/init as init process
[ 5.052297] with arguments:
[ 5.052303] /sbin/init
[ 5.052308] with environment:
[ 5.052313] HOME=/
[ 5.052317] TERM=linux
[ 5.376865] init: Console is alive
[ 5.380513] init: - watchdog -
[ 6.080900] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.180900] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.194519] fsl-ehci: Freescale EHCI Host controller driver
[ 6.205162] ehci-orion: EHCI orion driver
[ 6.209376] orion-ehci f1050000.ehci: EHCI Host Controller
[ 6.214960] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 6.222813] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000
[ 6.251584] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 6.258207] hub 1-0:1.0: USB hub found
[ 6.262702] hub 1-0:1.0: 1 port detected
[ 6.273198] ehci-platform: EHCI generic platform driver
[ 6.293191] rtc-s35390a 0-0030: registered as rtc0
[ 6.298978] rtc-s35390a 0-0030: setting system clock to 2024-01-26T21:59:43 UTC (1706306383)
[ 6.324789] mvsdio f1090000.mvsdio: Got CD GPIO
[ 6.361785] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.371403] init: - preinit -
[ 6.691586] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 6.934103] hub 1-1:1.0: USB hub found
[ 6.944351] hub 1-1:1.0: 4 ports detected
[ 6.987312] mtdblock: MTD device 'bootldr-env' is NAND, please consider using UBI block devices instead.
[ 7.641024] mv643xx_eth_port mv643xx_eth_port.1 eth1: link up, 1000 Mb/s, full duplex, flow control disabled
[ 7.652031] mv88e6085 f1072004.mdio-bus-mii:10 lan1: configuring for phy/gmii link mode
[ 7.664989] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 9.838868] UBIFS (ubi0:2): Mounting in unauthenticated mode
[ 9.870320] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 605
[ 9.903383] UBIFS (ubi0:2): recovery needed
[ 10.032447] UBIFS (ubi0:2): recovery completed
[ 10.037081] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 10.044981] UBIFS (ubi0:2): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 10.054958] UBIFS (ubi0:2): FS size: 106315776 bytes (101 MiB, 824 LEBs), max 835 LEBs, journal size 5289984 bytes (5 MiB, 41 LEBs)
[ 10.066859] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB)
[ 10.073519] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 0083EAEC-0C12-4A7F-85E6-1FCAF1D0DBE2, small LPT model
[ 10.089342] mount_root: switching to ubifs overlay
[ 10.102185] urandom-seed: Seeding with /etc/urandom.seed
[ 10.273220] procd: - early -
[ 10.276265] procd: - watchdog -
[ 10.935571] procd: - watchdog -
[ 10.939834] procd: - ubus -
[ 11.001489] procd: - init -
[ 11.610346] urngd: jent-rng init failed, err: 11
[ 11.802787] kmodloader: loading kernel modules from /etc/modules.d/*
[ 12.036873] tun: Universal TUN/TAP device driver, 1.6
[ 12.056987] Loading modules backported from Linux version v6.1.24-0-g0102425ac76b
[ 12.064557] Backport generated by backports.git v5.15.92-1-44-gd6ea70fafd36
[ 12.250176] PPP generic driver version 2.4.2
[ 12.263709] NET: Registered PF_PPPOX protocol family
[ 12.327498] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 23.283136] br: port 1(eth0) entered blocking state
[ 23.288066] br: port 1(eth0) entered disabled state
[ 23.307401] mv643xx_eth_port mv643xx_eth_port.1 eth1: link up, 1000 Mb/s, full duplex, flow control disabled
[ 23.354405] mv88e6085 f1072004.mdio-bus-mii:10 lan1: configuring for phy/gmii link mode
[ 23.395043] br: port 2(lan1) entered blocking state
[ 23.399960] br: port 2(lan1) entered disabled state
[ 23.442097] device lan1 entered promiscuous mode
[ 23.446749] device eth1 entered promiscuous mode
[ 23.451506] device eth0 entered promiscuous mode
[ 23.727123] mv88e6085 f1072004.mdio-bus-mii:10: port 1 failed to add 00:1c:7f:<ommited> vid 251 to fdb: -95
[ 24.031987] mv88e6085 f1072004.mdio-bus-mii:10: port 1 failed to add 00:1c:7f:<ommited> vid 200 to fdb: -95
[ 24.086105] mv88e6085 f1072004.mdio-bus-mii:10: port 1 failed to add 00:1c:7f:<ommited> vid 24 to fdb: -95
[ 24.096503] mv88e6085 f1072004.mdio-bus-mii:10 lan2: configuring for phy/gmii link mode
[ 24.119068] mv88e6085 f1072004.mdio-bus-mii:10: port 1 failed to add 00:1c:7f:<ommited> vid 23 to fdb: -95
[ 24.144225] br: port 3(lan2) entered blocking state
[ 24.149138] br: port 3(lan2) entered disabled state
[ 24.230571] device lan2 entered promiscuous mode
[ 24.297053] mv88e6085 f1072004.mdio-bus-mii:10: port 1 failed to add 00:1c:7f:<ommited> vid 22 to fdb: -95
[ 24.463153] mv88e6085 f1072004.mdio-bus-mii:10: port 3 failed to add 00:1c:7f:<ommited> vid 251 to fdb: -95
[ 24.510081] mv88e6085 f1072004.mdio-bus-mii:10: port 3 failed to add 00:1c:7f:<ommited> vid 200 to fdb: -95
[ 24.520524] mv88e6085 f1072004.mdio-bus-mii:11 lan3: configuring for phy/gmii link mode
[ 24.546648] mv88e6085 f1072004.mdio-bus-mii:10: port 3 failed to add 00:1c:7f:<ommited> vid 24 to fdb: -95
[ 24.570944] br: port 4(lan3) entered blocking state
[ 24.575878] br: port 4(lan3) entered disabled state
[ 24.660416] device lan3 entered promiscuous mode
[ 24.726854] mv88e6085 f1072004.mdio-bus-mii:10: port 3 failed to add 00:1c:7f:<ommited> vid 23 to fdb: -95
[ 24.814276] mv88e6085 f1072004.mdio-bus-mii:10: port 3 failed to add 00:1c:7f:<ommited> vid 22 to fdb: -95
[ 24.848829] mv88e6085 f1072004.mdio-bus-mii:11 lan4: configuring for phy/gmii link mode
[ 24.892984] br: port 5(lan4) entered blocking state
[ 24.897899] br: port 5(lan4) entered disabled state
[ 24.982112] device lan4 entered promiscuous mode
[ 25.185250] mv88e6085 f1072004.mdio-bus-mii:11: port 0 failed to add 00:1c:7f:<ommited> vid 251 to fdb: -95
[ 25.245054] mv88e6085 f1072004.mdio-bus-mii:11: port 0 failed to add 00:1c:7f:<ommited> vid 200 to fdb: -95
[ 25.255495] mv88e6085 f1072004.mdio-bus-mii:10 lan5: configuring for phy/gmii link mode
[ 25.279140] mv88e6085 f1072004.mdio-bus-mii:11: port 0 failed to add 00:1c:7f:<ommited> vid 24 to fdb: -95
[ 25.301435] br: port 6(lan5) entered blocking state
[ 25.306363] br: port 6(lan5) entered disabled state
[ 25.392644] device lan5 entered promiscuous mode
[ 25.458604] mv88e6085 f1072004.mdio-bus-mii:11: port 0 failed to add 00:1c:7f:<ommited> vid 23 to fdb: -95
[ 25.762165] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control enabled
[ 25.802310] mv88e6085 f1072004.mdio-bus-mii:11: port 0 failed to add 00:1c:7f:24:85:26 vid 22 to fdb: -95
[ 25.859325] mv88e6085 f1072004.mdio-bus-mii:10 lan6: configuring for phy/gmii link mode
[ 25.897087] br: port 7(lan6) entered blocking state
[ 25.902027] br: port 7(lan6) entered disabled state
[ 26.014184] device lan6 entered promiscuous mode
[ 26.235815] mv88e6085 f1072004.mdio-bus-mii:11: port 2 failed to add 00:1c:7f:<ommited> vid 251 to fdb: -95
[ 26.286265] mv88e6085 f1072004.mdio-bus-mii:11: port 2 failed to add 00:1c:7f:<ommited> vid 200 to fdb: -95
[ 26.296707] mv88e6085 f1072004.mdio-bus-mii:10 lan7: configuring for phy/gmii link mode
[ 26.320308] mv88e6085 f1072004.mdio-bus-mii:11: port 2 failed to add 00:1c:7f:<ommited> vid 24 to fdb: -95
[ 26.350030] br: port 8(lan7) entered blocking state
[ 26.354959] br: port 8(lan7) entered disabled state
[ 26.462816] device lan7 entered promiscuous mode
[ 26.576136] mv88e6085 f1072004.mdio-bus-mii:11: port 2 failed to add 00:1c:7f:<ommited> vid 22 to fdb: -95
[ 27.008904] mv88e6085 f1072004.mdio-bus-mii:10: port 0 failed to add 00:1c:7f:<ommited> vid 251 to fdb: -95
[ 27.054620] mv88e6085 f1072004.mdio-bus-mii:10: port 0 failed to add 00:1c:7f:<ommited> vid 200 to fdb: -95
[ 27.065062] mv88e6085 f1072004.mdio-bus-mii:11 lan8: configuring for phy/gmii link mode
[ 27.088750] mv88e6085 f1072004.mdio-bus-mii:10: port 0 failed to add 00:1c:7f:<ommited> vid 24 to fdb: -95
[ 27.107998] br: port 9(lan8) entered blocking state
[ 27.112928] br: port 9(lan8) entered disabled state
[ 27.240362] device lan8 entered promiscuous mode
[ 27.913032] mv88e6085 f1072004.mdio-bus-mii:10: port 2 failed to add 00:1c:7f:<ommited> vid 251 to fdb: -95
[ 27.923123] br: port 1(eth0) entered blocking state
[ 27.928038] br: port 1(eth0) entered forwarding state
[ 27.940609] mv88e6085 f1072004.mdio-bus-mii:10: port 2 failed to add 00:1c:7f:<ommited> vid 200 to fdb: -95
[ 28.036993] mv88e6085 f1072004.mdio-bus-mii:10 lan6: Link is Up - 100Mbps/Full - flow control off
[ 28.104226] br: port 7(lan6) entered blocking state
[ 28.109181] br: port 7(lan6) entered forwarding state
[ 28.141998] mv88e6085 f1072004.mdio-bus-mii:10: port 4 failed to add 00:1c:7f:<ommited> vid 251 to fdb: -95
[ 28.229877] mv88e6085 f1072004.mdio-bus-mii:10: port 4 failed to add 00:1c:7f:<ommited> vid 200 to fdb: -95
[ 28.240411] mv88e6085 f1072004.mdio-bus-mii:11 dmz: configuring for phy/gmii link mode
[ 28.452760] mv88e6085 f1072004.mdio-bus-mii:11: port 1 failed to add 00:1c:7f:<ommited> vid 251 to fdb: -95
[ 28.507565] mv88e6085 f1072004.mdio-bus-mii:11: port 1 failed to add 00:1c:7f:<ommited> vid 200 to fdb: -95
[ 28.520049] mv88e6085 f1072004.mdio-bus-mii:10 lan5: Link is Up - 100Mbps/Full - flow control rx/tx
[ 28.573001] br: port 6(lan5) entered blocking state
[ 28.577934] br: port 6(lan5) entered forwarding state
[ 30.261380] mv88e6085 f1072004.mdio-bus-mii:11 lan8: Link is Up - 100Mbps/Full - flow control off
[ 30.291586] br: port 9(lan8) entered blocking state
[ 30.296515] br: port 9(lan8) entered forwarding state
[ 38.752679] mv88e6085 f1072004.mdio-bus-mii:10 lan2: Link is Up - 100Mbps/Full - flow control rx/tx
[ 38.771393] br: port 3(lan2) entered blocking state
[ 38.776367] br: port 3(lan2) entered forwarding state
[ 75.061049] mv88e6085 f1072004.mdio-bus-mii:10: port 1 failed to add f0:ce:ee:27:8b:05 vid 251 to fdb: -95
[ 75.088842] mv88e6085 f1072004.mdio-bus-mii:10: port 3 failed to add f0:ce:ee:27:8b:05 vid 251 to fdb: -95
[ 75.117288] mv88e6085 f1072004.mdio-bus-mii:11: port 0 failed to add f0:ce:ee:27:8b:05 vid 251 to fdb: -95
[ 75.153329] mv88e6085 f1072004.mdio-bus-mii:11: port 2 failed to add f0:ce:ee:27:8b:05 vid 251 to fdb: -95
[ 75.192961] mv88e6085 f1072004.mdio-bus-mii:10: port 0 failed to add f0:ce:ee:27:8b:05 vid 251 to fdb: -95
[ 75.223319] mv88e6085 f1072004.mdio-bus-mii:10: port 2 failed to add f0:ce:ee:27:8b:05 vid 251 to fdb: -95
[ 75.262474] mv88e6085 f1072004.mdio-bus-mii:10: port 4 failed to add f0:ce:ee:27:8b:05 vid 251 to fdb: -95
[ 75.306447] mv88e6085 f1072004.mdio-bus-mii:11: port 1 failed to add f0:ce:ee:27:8b:05 vid 251 to fdb: -95
[ 271.687310] br: port 3(lan2) entered disabled state
[ 271.696392] mv88e6085 f1072004.mdio-bus-mii:10 lan2: Link is Down
[ 278.979734] mv88e6085 f1072004.mdio-bus-mii:10 lan2: Link is Up - 1Gbps/Full - flow control rx/tx
[ 278.988979] br: port 3(lan2) entered blocking state
[ 278.993901] br: port 3(lan2) entered forwarding state
[ 1597.191020] mv88e6085 f1072004.mdio-bus-mii:10: port 1 failed to add a8:22:04:b8:04:81 vid 251 to fdb: -95
[ 1597.209019] mv88e6085 f1072004.mdio-bus-mii:10: port 3 failed to add a8:22:04:b8:04:81 vid 251 to fdb: -95
[ 1597.225954] mv88e6085 f1072004.mdio-bus-mii:11: port 0 failed to add a8:22:04:b8:04:81 vid 251 to fdb: -95
[ 1597.243329] mv88e6085 f1072004.mdio-bus-mii:11: port 2 failed to add a8:22:04:b8:04:81 vid 251 to fdb: -95
[ 1597.260646] mv88e6085 f1072004.mdio-bus-mii:10: port 0 failed to add a8:22:04:b8:04:81 vid 251 to fdb: -95
[ 1597.276838] mv88e6085 f1072004.mdio-bus-mii:10: port 2 failed to add a8:22:04:b8:04:81 vid 251 to fdb: -95
[ 1597.294808] mv88e6085 f1072004.mdio-bus-mii:10: port 4 failed to add a8:22:04:b8:04:81 vid 251 to fdb: -95
[ 1597.315589] mv88e6085 f1072004.mdio-bus-mii:11: port 1 failed to add a8:22:04:b8:04:81 vid 251 to fdb: -95
root@ap-escritorio:~# iperf3 -s
-----------------------------------------------------------
Server listening on 5201 (test #1)
-----------------------------------------------------------
Accepted connection from 172.21.0.85, port 38638
[ 5] local 172.24.0.120 port 5201 connected to 172.21.0.85 port 38650
[ ID] Interval Transfer Bitrate
[ 5] 0.00-1.00 sec 27.0 MBytes 226 Mbits/sec
[ 5] 1.00-2.00 sec 31.2 MBytes 262 Mbits/sec
[ 5] 2.00-3.00 sec 29.9 MBytes 251 Mbits/sec
[ 5] 3.00-4.00 sec 31.9 MBytes 267 Mbits/sec
[ 5] 4.00-5.00 sec 32.6 MBytes 274 Mbits/sec
[ 5] 5.00-6.00 sec 30.5 MBytes 256 Mbits/sec
[ 5] 6.00-7.00 sec 28.0 MBytes 235 Mbits/sec
[ 5] 7.00-8.00 sec 30.1 MBytes 253 Mbits/sec
[ 5] 8.00-9.00 sec 31.4 MBytes 263 Mbits/sec
[ 5] 9.00-10.00 sec 30.6 MBytes 257 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate
[ 5] 0.00-10.00 sec 303 MBytes 254 Mbits/sec receiver
If anyone needs more information, just ask me..
It is not recommended to run iperf3 on the router since the cpu is often not powerful enough and will struggle. A better test is to run iperf3 on different wired computers to test throughput such that the router is just doing the routing. That way you should get better results more representative of the actual performance of the device.
1 Like
I can do nvidia jetson and xavier nano, do you support both now, or just the jetson nano ?