Linksys e4200 V2 dmesg below:
root@OpenWrt:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.15.105 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 12.2.0 r22514-c8934099bf) 12.2.0, GNU ld (GNU Binutils) 2.40.0) #0 Fri Apr 7 22:47:12 2023
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] OF: fdt: Machine model: Linksys E4200 v2 (Viper)
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:512k(uboot)ro,128k@512k(u_env),128k@640k(s_env),26m@2m(kernel),26m@2m(rootfs)fs,26m@28m(alt_kernel),26m@28m(alt_rootfs)fs,74m@54m(syscfg) root=/dev/mtdblock6 ro rootfstype=jffs2 serial_number=01C1460C100051 uuid=928AA8A30A4A8BC26EC252EF49B6677B hw_version=RGWM-C4_0GA device_mac=58:6D:8F:FA:11:CE factory_date=2011/12/28 wps_pin=56427776
[ 0.000000] Unknown kernel command line parameters "mangled_fs=jffs2 serial_number=01C1460C100051 uuid=928AA8A30A4A8BC26EC252EF49B6677B hw_version=RGWM-C4_0GA device_mac=58:6D:8F:FA:11:CE factory_date=2011/12/28 wps_pin=56427776", will be passed to user space.
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 119680K/131072K available (6314K kernel code, 586K rwdata, 1632K rodata, 1024K init, 217K bss, 11392K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000001] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.000039] Switching to timer-based delay loop, resolution 5ns
[ 0.000198] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
[ 0.000229] pid_max: default: 32768 minimum: 301
[ 0.000460] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.000495] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.001410] CPU: Testing write buffer coherency: ok
[ 0.002786] Setting up static identity map for 0x100000 - 0x10003c
[ 0.003038] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1
[ 0.003253] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.006407] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.006447] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.006585] pinctrl core: initialized pinctrl subsystem
[ 0.008093] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.008591] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.009565] thermal_sys: Registered thermal governor 'step_wise'
[ 0.009657] cpuidle: using governor ladder
[ 0.010098] Feroceon L2: Enabling L2
[ 0.010139] Feroceon L2: Cache support initialised.
[ 0.015284] No ATAGs?
[ 0.021707] SCSI subsystem initialized
[ 0.021893] libata version 3.00 loaded.
[ 0.022101] usbcore: registered new interface driver usbfs
[ 0.022156] usbcore: registered new interface driver hub
[ 0.022202] usbcore: registered new device driver usb
[ 0.023338] clocksource: Switched to clocksource orion_clocksource
[ 0.024106] NET: Registered PF_INET protocol family
[ 0.024282] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.024828] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.024868] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.024889] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.024914] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.024938] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.025012] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.025043] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.025249] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.025290] PCI: CLS 0 bytes, default 32
[ 0.027082] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.031498] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.031523] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.033007] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.034942] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 0.036077] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges:
[ 0.036132] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[ 0.036165] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1044000..0x00f1045fff -> 0x0000044000
[ 0.036194] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1080000..0x00f1081fff -> 0x0000080000
[ 0.036222] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 0.036249] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 0.036276] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 0.036297] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 0.036575] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[ 0.036595] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.036615] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[ 0.036633] pci_bus 0000:00: root bus resource [mem 0xf1044000-0xf1045fff] (bus address [0x00044000-0x00045fff])
[ 0.036649] pci_bus 0000:00: root bus resource [mem 0xf1080000-0xf1081fff] (bus address [0x00080000-0x00081fff])
[ 0.036664] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[ 0.036678] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 0.036774] pci 0000:00:01.0: [11ab:6282] type 01 class 0x060400
[ 0.037026] pci 0000:00:02.0: [11ab:6282] type 01 class 0x060400
[ 0.038111] PCI: bus0: Fast back to back transfers disabled
[ 0.038130] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.038149] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.038295] pci 0000:01:00.0: [11ab:2a41] type 00 class 0x020000
[ 0.038335] pci 0000:01:00.0: reg 0x10: [mem 0x90000000-0x9000ffff 64bit]
[ 0.038368] pci 0000:01:00.0: reg 0x18: [mem 0x90010000-0x9001ffff 64bit]
[ 0.039571] PCI: bus1: Fast back to back transfers disabled
[ 0.039589] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.039732] pci 0000:02:00.0: [11ab:2a42] type 00 class 0x020000
[ 0.039772] pci 0000:02:00.0: reg 0x10: [mem 0x98000000-0x9800ffff 64bit]
[ 0.039803] pci 0000:02:00.0: reg 0x18: [mem 0x98010000-0x9801ffff 64bit]
[ 0.041002] PCI: bus2: Fast back to back transfers disabled
[ 0.041019] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 0.041218] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe00fffff]
[ 0.041242] pci 0000:00:02.0: BAR 8: assigned [mem 0xe0100000-0xe01fffff]
[ 0.041262] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
[ 0.041289] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0010000-0xe001ffff 64bit]
[ 0.041315] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.041332] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff]
[ 0.041358] pci 0000:02:00.0: BAR 0: assigned [mem 0xe0100000-0xe010ffff 64bit]
[ 0.041385] pci 0000:02:00.0: BAR 2: assigned [mem 0xe0110000-0xe011ffff 64bit]
[ 0.041411] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 0.041427] pci 0000:00:02.0: bridge window [mem 0xe0100000-0xe01fffff]
[ 0.041876] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.043525] printk: console [ttyS0] disabled
[ 0.043623] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A
[ 0.831992] printk: console [ttyS0] enabled
[ 0.836813] Loading iSCSI transport class v2.0-870.
[ 0.846642] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 0.853035] nand: Hynix H27U1G8F2BTR-BC
[ 0.856926] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.864571] Scanning device for bad blocks
[ 0.934551] mtd: bad character after partition (f)
[ 0.939392] 9 fixed-partitions partitions found on MTD device orion_nand
[ 0.946146] Creating 9 MTD partitions on "orion_nand":
[ 0.951313] 0x000000000000-0x000000080000 : "u-boot"
[ 0.958835] 0x000000080000-0x0000000a0000 : "u_env"
[ 0.964314] 0x0000000a0000-0x0000000c0000 : "s_env"
[ 0.971002] 0x000000200000-0x000001c00000 : "kernel1"
[ 0.976767] 0x000000500000-0x000001c00000 : "rootfs1"
[ 0.983705] 0x000001c00000-0x000003600000 : "kernel2"
[ 0.989390] 0x000001f00000-0x000003600000 : "ubi"
[ 0.996004] 0x000003600000-0x000008000000 : "syscfg"
[ 1.001783] 0x0000000c0000-0x000000200000 : "unused"
[ 1.025138] mv88e6085 f1072004.mdio-bus-mii:10: switch 0x1710 detected: Marvell 88E6171, revision 2
[ 1.187419] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 1.195070] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:50:43:00:02:02
[ 1.204070] i2c_dev: i2c /dev entries driver
[ 1.209213] orion_wdt: Initial timeout 21 sec
[ 1.223881] marvell-cesa f1030000.crypto: CESA device successfully registered
[ 1.231878] NET: Registered PF_INET6 protocol family
[ 1.238987] Segment Routing with IPv6
[ 1.242730] In-situ OAM (IOAM) with IPv6
[ 1.246779] NET: Registered PF_PACKET protocol family
[ 1.251906] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.265164] 8021q: 802.1Q VLAN Support v1.8
[ 1.273632] mv88e6085 f1072004.mdio-bus-mii:10: switch 0x1710 detected: Marvell 88E6171, revision 2
[ 2.449655] mv88e6085 f1072004.mdio-bus-mii:10: configuring for fixed/ link mode
[ 2.462483] mv88e6085 f1072004.mdio-bus-mii:10: Link is Up - 1Gbps/Full - flow control off
[ 2.472189] mv88e6085 f1072004.mdio-bus-mii:10 ethernet1 (uninitialized): PHY [mv88e6xxx-1:00] driver [Generic PHY] (irq=POLL)
[ 2.492501] mv88e6085 f1072004.mdio-bus-mii:10 ethernet2 (uninitialized): PHY [mv88e6xxx-1:01] driver [Generic PHY] (irq=POLL)
[ 2.511984] mv88e6085 f1072004.mdio-bus-mii:10 ethernet3 (uninitialized): PHY [mv88e6xxx-1:02] driver [Generic PHY] (irq=POLL)
[ 2.531426] mv88e6085 f1072004.mdio-bus-mii:10 ethernet4 (uninitialized): PHY [mv88e6xxx-1:03] driver [Generic PHY] (irq=POLL)
[ 2.550911] mv88e6085 f1072004.mdio-bus-mii:10 internet (uninitialized): PHY [mv88e6xxx-1:04] driver [Generic PHY] (irq=POLL)
[ 2.565742] DSA: tree 0 setup
[ 2.569095] UBI: auto-attach mtd6
[ 2.572433] ubi0: attaching mtd6
[ 2.595886] ubi0: scanning is finished
[ 2.606226] ubi0: attached mtd6 (name "ubi", size 23 MiB)
[ 2.611667] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[ 2.618596] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[ 2.625349] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
[ 2.632175] ubi0: good PEBs: 184, bad PEBs: 0, corrupted PEBs: 0
[ 2.638221] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 2.645492] ubi0: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 1235417247
[ 2.654683] ubi0: available PEBs: 0, total reserved PEBs: 184, PEBs reserved for bad PEB handling: 20
[ 2.664200] ubi0: background thread "ubi_bgt0d" started, PID 309
[ 2.671093] block ubiblock0_0: created from ubi0:0(rootfs)
[ 2.676644] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 2.688096] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 2.698138] Freeing unused kernel image (initmem) memory: 1024K
[ 2.704609] Run /sbin/init as init process
[ 2.708730] with arguments:
[ 2.708735] /sbin/init
[ 2.708739] with environment:
[ 2.708743] HOME=/
[ 2.708747] TERM=linux
[ 2.708751] mangled_fs=jffs2
[ 2.708755] serial_number=01C1460C100051
[ 2.708760] uuid=928AA8A30A4A8BC26EC252EF49B6677B
[ 2.708765] hw_version=RGWM-C4_0GA
[ 2.708770] device_mac=58:6D:8F:FA:11:CE
[ 2.708774] factory_date=2011/12/28
[ 2.708779] wps_pin=56427776
[ 3.025720] init: Console is alive
[ 3.029388] init: - watchdog -
[ 3.527444] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.586054] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.596919] fsl-ehci: Freescale EHCI Host controller driver
[ 3.604723] ehci-orion: EHCI orion driver
[ 3.608933] orion-ehci f1050000.ehci: EHCI Host Controller
[ 3.614510] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 3.622335] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[ 3.653365] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 3.660009] hub 1-0:1.0: USB hub found
[ 3.664441] hub 1-0:1.0: 1 port detected
[ 3.671021] ehci-platform: EHCI generic platform driver
[ 3.681687] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.691750] init: - preinit -
[ 4.358955] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.409535] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.465015] mtdblock: MTD device 'u_env' is NAND, please consider using UBI block devices instead.
[ 4.517983] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.759927] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 4.770909] mv88e6085 f1072004.mdio-bus-mii:10 ethernet1: configuring for phy/gmii link mode
[ 4.781946] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 6.949196] UBIFS (ubi0:1): default file-system created
[ 6.954974] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 6.974612] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 447
[ 7.012578] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 7.020487] UBIFS (ubi0:1): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 7.030468] UBIFS (ubi0:1): FS size: 16257024 bytes (15 MiB, 126 LEBs), max 136 LEBs, journal size 1032193 bytes (0 MiB, 6 LEBs)
[ 7.042099] UBIFS (ubi0:1): reserved for root: 767859 bytes (749 KiB)
[ 7.048578] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 0E3BF013-1529-4B22-A96E-22214E159DA6, small LPT model
[ 7.061693] mount_root: overlay filesystem has not been fully initialized yet
[ 7.069371] mount_root: switching to ubifs overlay
[ 7.079428] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 7.164330] procd: - early -
[ 7.167391] procd: - watchdog -
[ 7.792417] procd: - watchdog -
[ 7.795996] procd: - ubus -
[ 7.886230] random: ubusd: uninitialized urandom read (4 bytes read)
[ 7.949623] random: ubusd: uninitialized urandom read (4 bytes read)
[ 7.956439] random: ubusd: uninitialized urandom read (4 bytes read)
[ 7.965961] procd: - init -
[ 8.612275] kmodloader: loading kernel modules from /etc/modules.d/*
[ 8.761417] urngd: v1.0.2 started.
[ 8.926481] random: crng init done
[ 8.929910] random: 29 urandom warning(s) missed due to ratelimiting
[ 8.946506] Loading modules backported from Linux version v6.1-rc8-0-g76dcd734eca2
[ 8.954153] Backport generated by backports.git v5.15.81-1-41-g02e352527db5
[ 9.018748] Marvell TOPDOG(R) 802.11 Wireless Network Driver version 0.13
[ 9.025650] pci 0000:00:01.0: enabling device (0140 -> 0142)
[ 9.740249] ieee80211 phy0: Command RF_ANTENNA error 0x2
[ 9.745632] ieee80211 phy0: failed to set # of RX antennas
[ 9.751169] ieee80211 phy0: Command RF_ANTENNA error 0x2
[ 9.756530] ieee80211 phy0: failed to set # of TX antennas
[ 9.762053] ieee80211 phy0: 88w8366 v48, 586d8ffa11d0, STA firmware 4.1.0.3
[ 9.772799] pci 0000:00:02.0: enabling device (0140 -> 0142)
[ 10.530097] ieee80211 phy1: Command RF_ANTENNA error 0x2
[ 10.535498] ieee80211 phy1: failed to set # of RX antennas
[ 10.592000] ieee80211 phy1: Command RF_ANTENNA error 0x2
[ 10.597411] ieee80211 phy1: failed to set # of TX antennas
[ 10.602943] ieee80211 phy1: 88w8366 v48, 586d8ffa11d2, STA firmware 4.1.0.3
[ 10.677916] PPP generic driver version 2.4.2
[ 10.709786] NET: Registered PF_PPPOX protocol family
[ 10.732405] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 11.228118] mtdblock: MTD device 'u_env' is NAND, please consider using UBI block devices instead.
[ 35.187110] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 35.205795] mv88e6085 f1072004.mdio-bus-mii:10 ethernet1: configuring for phy/gmii link mode
[ 35.236377] br-lan: port 1(ethernet1) entered blocking state
[ 35.242086] br-lan: port 1(ethernet1) entered disabled state
[ 35.311227] device ethernet1 entered promiscuous mode
[ 35.316339] device eth0 entered promiscuous mode
[ 35.515217] mv88e6085 f1072004.mdio-bus-mii:10 ethernet2: configuring for phy/gmii link mode
[ 35.534993] br-lan: port 2(ethernet2) entered blocking state
[ 35.540694] br-lan: port 2(ethernet2) entered disabled state
[ 35.652893] device ethernet2 entered promiscuous mode
[ 35.714380] mv88e6085 f1072004.mdio-bus-mii:10 ethernet3: configuring for phy/gmii link mode
[ 35.738533] br-lan: port 3(ethernet3) entered blocking state
[ 35.744267] br-lan: port 3(ethernet3) entered disabled state
[ 35.832255] device ethernet3 entered promiscuous mode
[ 35.884212] mv88e6085 f1072004.mdio-bus-mii:10 ethernet4: configuring for phy/gmii link mode
[ 35.906187] br-lan: port 4(ethernet4) entered blocking state
[ 35.911896] br-lan: port 4(ethernet4) entered disabled state
[ 35.999454] device ethernet4 entered promiscuous mode
[ 36.055826] mv88e6085 f1072004.mdio-bus-mii:10 internet: configuring for phy/gmii link mode
[ 40.740119] mv88e6085 f1072004.mdio-bus-mii:10 ethernet1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 40.749527] br-lan: port 1(ethernet1) entered blocking state
[ 40.755238] br-lan: port 1(ethernet1) entered forwarding state
[ 40.765318] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 41.778547] br-lan: port 1(ethernet1) entered disabled state
[ 41.787333] mv88e6085 f1072004.mdio-bus-mii:10 ethernet1: Link is Down
[ 43.860131] mv88e6085 f1072004.mdio-bus-mii:10 ethernet1: Link is Up - 1Gbps/Full - flow control off
[ 43.869366] br-lan: port 1(ethernet1) entered blocking state
[ 43.875078] br-lan: port 1(ethernet1) entered forwarding state
[ 44.892221] br-lan: port 1(ethernet1) entered disabled state
[ 44.899751] mv88e6085 f1072004.mdio-bus-mii:10 ethernet1: Link is Down
[ 48.024297] mv88e6085 f1072004.mdio-bus-mii:10 ethernet1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 48.033695] br-lan: port 1(ethernet1) entered blocking state
[ 48.039392] br-lan: port 1(ethernet1) entered forwarding state