Hi, I'm trying to setup an usb hard drive for network storage.
On Linksys EA6350 v4 with OpenWrt 22.03.3 and SCSI SSD Drive with usb3 i think
when i reboot the rooter and the light on the ssd drive light and soon after the rooter establish connection the light stop and no sign of usb device. I tryed with usb pen drive and other hard drive, same result. The think is thah the on light of the drive light onli when reboot and whes start the sistem the light is off again.
What can be the problem? I provide the log and som info down:
I`m using this reference:
https://openwrt.org/docs/guide-user/storage/usb-drives
and this:
https://openwrt.org/docs/guide-user/storage/usb-installing
i have this packs instald:
kmod-usb-core - 5.10.161-1
kmod-usb-ehci - 5.10.161-1
kmod-usb-storage - 5.10.161-1
kmod-usb-storage-extras - 5.10.161-1
kmod-usb-storage-uas - 5.10.161-1
kmod-usb-uhci - 5.10.161-1
kmod-usb-xhci-hcd - 5.10.161-1
kmod-usb-xhci-mtk - 5.10.161-1
kmod-usb2 - 5.10.161-1
kmod-usb3 - 5.10.161-1
libusb-1.0-0 - 1.0.24-5
usbutils - 014-1
root@OpenWrt:~# lsusb -t
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci-mtk/1p, 5000M
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci-mtk/2p, 480M
root@OpenWrt:~# cat /sys/kernel/debug/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 2
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 5.10
S: Manufacturer=Linux 5.10.161 xhci-hcd
S: Product=xHCI Host Controller
S: SerialNumber=1e1c0000.xhci
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=5000 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 3.00 Cls=09(hub ) Sub=00 Prot=03 MxPS= 9 #Cfgs= 1
P: Vendor=1d6b ProdID=0003 Rev= 5.10
S: Manufacturer=Linux 5.10.161 xhci-hcd
S: Product=xHCI Host Controller
S: SerialNumber=1e1c0000.xhci
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
not registered here:
root@OpenWrt:~# cat /sys/module/usb_storage/parameters/quirks
and this is the log:
4.579770] usbcore: registered new interface driver usbfs
[ 4.585488] usbcore: registered new interface driver hub
[ 4.590989] usbcore: registered new device driver usb
[ 4.606246] xhci-mtk 1e1c0000.xhci: supply vbus not found, using dummy regulator
[ 4.613946] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regulator
[ 4.621791] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 4.627125] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[ 4.640148] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010
[ 4.649321] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
[ 4.656408] hub 1-0:1.0: USB hub found
[ 4.660365] hub 1-0:1.0: 2 ports detected
[ 4.665067] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 4.670518] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[ 4.678000] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[ 4.684605] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.693626] hub 2-0:1.0: USB hub found
[ 4.697519] hub 2-0:1.0: 1 port detected
[ 4.709110] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.730375] init: - preinit -
[ 5.077341] usb 2-1: new SuperSpeed Gen 1 USB device number 2 using xhci-mtk
[ 5.191246] random: procd: uninitialized urandom read (4 bytes read)
[ 5.531012] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.610926] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.181291] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 6.190166] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 6.196863] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 6.200469] 8021q: adding VLAN 0 to HW filter on device lan1
[ 6.213567] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 10.406266] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 10.412255] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 619
[ 10.492419] UBIFS (ubi0:1): recovery needed
[ 10.678543] UBIFS (ubi0:1): recovery completed
[ 10.683238] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 10.691073] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 10.700966] UBIFS (ubi0:1): FS size: 27299840 bytes (26 MiB, 215 LEBs), journal size 1396736 bytes (1 MiB, 11 LEBs)
[ 10.711374] UBIFS (ubi0:1): reserved for root: 1289438 bytes (1259 KiB)
[ 10.717963] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 13CF5E3A-B27F-4FC6-B962-CB1CFDF63801, small LPT model
[ 10.744318] mount_root: loading kmods from internal overlay
[ 10.895777] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 10.943201] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 10.987509] SCSI subsystem initialized
[ 11.006266] ehci-fsl: Freescale EHCI Host controller driver
[ 11.013544] ehci-platform: EHCI generic platform driver
[ 11.028466] uhci_hcd: USB Universal Host Controller Interface driver
[ 11.050818] usb 2-1: USB controller 1e1c0000.xhci does not support streams, which are required by the UAS driver.
[ 11.061085] usb 2-1: Please try an other USB controller if you wish to use UAS.
[ 11.068361] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 11.075279] usb-storage 2-1:1.0: Quirks match for vid 152d pid 0578: 1000000
[ 11.082620] scsi host0: usb-storage 2-1:1.0
[ 11.087733] usbcore: registered new interface driver usb-storage
[ 11.098475] usbcore: registered new interface driver uas
[ 11.104493] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 11.272662] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 11.285823] block: extroot: not configured
[ 11.293175] mount_root: switching to ubifs overlay
[ 11.315616] urandom-seed: Seeding with /etc/urandom.seed
[ 11.389796] procd: - early -
[ 11.393063] procd: - watchdog -
[ 12.068403] procd: - watchdog -
[ 12.075725] procd: - ubus -
[ 12.141173] scsi 0:0:0:0: Direct-Access JMicron Tech 0508 PQ: 0 ANSI: 6
[ 12.154247] sd 0:0:0:0: [sda] 468862128 512-byte logical blocks: (240 GB/224 GiB)
[ 12.162572] sd 0:0:0:0: [sda] Write Protect is off
[ 12.167415] sd 0:0:0:0: [sda] Mode Sense: 47 00 00 08
[ 12.168084] sd 0:0:0:0: [sda] Disabling FUA
[ 12.172527] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 12.241052] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.250110] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.257108] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.267856] procd: - init -
[ 12.677246] sda: sda1
[ 12.685658] sd 0:0:0:0: [sda] Attached SCSI disk
[ 13.275347] kmodloader: loading kernel modules from /etc/modules.d/*
[ 13.420097] urngd: v1.0.2 started.
[ 13.600229] random: crng init done
[ 13.603652] random: 32 urandom warning(s) missed due to ratelimiting
[ 13.616778] fuse: init (API version 7.32)
[ 13.628354] Loading modules backported from Linux version v5.15.81-0-ge4a7232c917c
[ 13.635999] Backport generated by backports.git v5.15.81-1-0-ge1867d55
[ 13.659611] usbcore: registered new interface driver ums-alauda
[ 13.667003] usbcore: registered new interface driver ums-cypress
[ 13.674534] usbcore: registered new interface driver ums-datafab
[ 13.682030] usbcore: registered new interface driver ums-freecom
[ 13.689487] usbcore: registered new interface driver ums-isd200
[ 13.697022] usbcore: registered new interface driver ums-jumpshot
[ 13.704609] usbcore: registered new interface driver ums-karma
[ 13.712202] usbcore: registered new interface driver ums-sddr09
[ 13.719641] usbcore: registered new interface driver ums-sddr55
[ 13.727311] usbcore: registered new interface driver ums-usbat
[ 13.928156] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=22
[ 13.933672] pci 0000:00:00.0: enabling device (0006 -> 0007)
[ 13.939332] mt7603e 0000:01:00.0: enabling device (0000 -> 0002)
[ 13.945506] mt7603e 0000:01:00.0: ASIC revision: 76030010
[ 14.981291] mt7603e 0000:01:00.0: Firmware Version: ap_pcie
[ 14.986866] mt7603e 0000:01:00.0: Build Time: 20160107100755
[ 15.029990] mt7603e 0000:01:00.0: firmware init done
[ 15.201590] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 15.212663] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=23
[ 15.218133] pci 0000:00:01.0: enabling device (0006 -> 0007)
[ 15.223835] mt7615e 0000:02:00.0: enabling device (0000 -> 0002)
[ 15.243573] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 15.243624] ieee80211 phy1: copying sband (band 1) due to VHT EXT NSS BW flag
[ 15.294920] PPP generic driver version 2.4.2
[ 15.301131] NET: Registered protocol family 24
[ 15.313659] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 17.401910] mt7615e 0000:02:00.0: mediatek/mt7663pr2h.bin not found, switching to mediatek/mt7663pr2h_rebb.bin
[ 17.609187] mt7615e 0000:02:00.0: HW/SW Version: 0x65322d31, Build Time: 2009041715da1a1
[ 17.609187]
[ 17.822477] mt7615e 0000:02:00.0: N9 Firmware Version: 7663mp1827, Build Time: 20200904171623
[ 17.831045] mt7615e 0000:02:00.0: Region number: 0x3
[ 17.836008] mt7615e 0000:02:00.0: Parsing tailer Region: 0
[ 17.845332] mt7615e 0000:02:00.0: Region 0, override_addr = 0x00112c00
[ 17.851964] mt7615e 0000:02:00.0: Parsing tailer Region: 1
[ 17.858850] mt7615e 0000:02:00.0: Parsing tailer Region: 2
[ 17.866059] mt7615e 0000:02:00.0: override_addr = 0x00112c00, option = 3
[ 24.165091] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 24.183889] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 24.192181] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 24.196438] device eth0 entered promiscuous mode
[ 24.205892] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 24.213063] 8021q: adding VLAN 0 to HW filter on device lan1
[ 24.221646] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 24.229026] br-lan: port 1(lan1) entered blocking state
[ 24.234460] br-lan: port 1(lan1) entered disabled state
[ 24.240799] device lan1 entered promiscuous mode
[ 24.273631] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 24.280969] 8021q: adding VLAN 0 to HW filter on device lan2
[ 24.294121] br-lan: port 2(lan2) entered blocking state
[ 24.299413] br-lan: port 2(lan2) entered disabled state
[ 24.307224] device lan2 entered promiscuous mode
[ 24.322437] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 24.329745] 8021q: adding VLAN 0 to HW filter on device lan3
[ 24.339851] br-lan: port 3(lan3) entered blocking state
[ 24.345230] br-lan: port 3(lan3) entered disabled state
[ 24.352856] device lan3 entered promiscuous mode
[ 24.368574] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode
[ 24.375969] 8021q: adding VLAN 0 to HW filter on device lan4
[ 24.385409] br-lan: port 4(lan4) entered blocking state
[ 24.390739] br-lan: port 4(lan4) entered disabled state
[ 24.397594] device lan4 entered promiscuous mode
[ 24.420098] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode
[ 24.427172] 8021q: adding VLAN 0 to HW filter on device wan
[ 26.110259] br-lan: port 5(wlan1) entered blocking state
[ 26.115635] br-lan: port 5(wlan1) entered disabled state
[ 26.121719] device wlan1 entered promiscuous mode
[ 26.126904] br-lan: port 5(wlan1) entered blocking state
[ 26.132330] br-lan: port 5(wlan1) entered forwarding state
[ 26.138766] br-lan: port 5(wlan1) entered disabled state
[ 26.185831] br-lan: port 6(wlan0) entered blocking state
[ 26.191317] br-lan: port 6(wlan0) entered disabled state
[ 26.197406] device wlan0 entered promiscuous mode
[ 26.202655] br-lan: port 6(wlan0) entered blocking state
[ 26.208035] br-lan: port 6(wlan0) entered forwarding state
[ 26.213983] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 26.347698] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 26.785933] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 26.792757] br-lan: port 5(wlan1) entered blocking state
[ 26.798111] br-lan: port 5(wlan1) entered forwarding state
[ 27.402962] mt7530 mdio-bus:1f wan: Link is Up - 1Gbps/Full - flow control rx/tx
[ 27.410455] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready
[ 28.220211] usb 2-1: USB disconnect, device number 2
[ 28.227534] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 28.233713] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=0x01 driverbyte=0x00
10x