I'm following these directions, and mashing the down arrow throughout and never get a UBoot menu. However, I can hit f at that one point and bring up failsafe mode - should I just try one of the reset to factory commands there instead?
mtk_uartboot output:
mtk_uartboot - 0.1.1
Using serial port: COM5
Handshake...
hw code: 0x7622
hw sub code: 0x8a00
hw ver: 0xcb00
sw ver: 0x100
Baud rate set to 460800
sending payload to 0x201000...
Checksum: 0xc4df
Setting baudrate back to 115200
Jumping to 0x201000 in aarch64...
Waiting for BL2. Message below:
==================================
NOTICE: BL2: v2.10.0 (release):v2.4-rc0-5845-gbacca82a8
NOTICE: BL2: Built : 15:03:57, Jun 6 2024
NOTICE: WDT: Cold boot
NOTICE: CPU: MT7622
NOTICE: WDT: disabled
NOTICE: Starting UART download handshake ...
==================================
BL2 UART DL version: 0x10
Baudrate set to: 921600
FIP sent.
==================================
NOTICE: Received FIP 0xf914c @ 0x40400000 ...
==================================
serial output:
āāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāāādāĀ²
ā
Default Configuration: 'config-1'
Configuration 0 (config-1)
Description: OpenWrt linksys_e8450-ubi
Kernel: kernel-1
FDT: fdt-1
Loadables: rootfs-1
## Checking hash(es) for FIT Image at 48000000 ...
Hash(es) for Image 0 (kernel-1): crc32+ sha1+
Hash(es) for Image 1 (fdt-1): crc32+ sha1+
Hash(es) for Image 2 (rootfs-1): crc32+ sha1+
## Loading kernel from FIT Image at 48000000 ...
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-5.15.134
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x48001000
Data Size: 5134552 Bytes = 4.9 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x44000000
Entry Point: 0x44000000
Hash algo: crc32
Hash value: 8cbcc98f
Hash algo: sha1
Hash value: 44be371cfc95b4912d7be197de808629324dacbb
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 48000000 ...
Using 'config-1' configuration
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt linksys_e8450-ubi device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x484e7000
Data Size: 30483 Bytes = 29.8 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: 8bfe6f4a
Hash algo: sha1
Hash value: 6e246b55f03211a052e3d9e86f9b022da611ea3d
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x484e7000
Working FDT set to 484e7000
## Loading loadables from FIT Image at 48000000 ...
Trying 'rootfs-1' loadables subimage
Description: ARM64 OpenWrt linksys_e8450-ubi rootfs
Type: Filesystem Image
Compression: uncompressed
Data Start: 0x484ef000
Data Size: 4689920 Bytes = 4.5 MiB
Hash algo: crc32
Hash value: 4f7ee121
Hash algo: sha1
Hash value: c19fc8ab82d49394dffe59cddaee1cfb096086a8
Verifying Hash Integrity ... crc32+ sha1+ OK
Uncompressing Kernel Image
Loading Device Tree to 000000005e7e0000, end 000000005e7ea712 ... OK
Working FDT set to 5e7e0000
Add 'ramoops@42ff0000' node failed: FDT_ERR_EXISTS
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.15.134 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r23497-6637af95aa) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Mon Oct 9 21:45:35 2023
[ 0.000000] Machine model: Linksys E8450 (UBI)
[ 0.000000] earlycon: uart8250 at MMIO32 0x0000000011002000 (options '')
[ 0.000000] printk: bootconsole [uart8250] enabled
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000005fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff]
[ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff]
[ 0.000000] node 0: [mem 0x0000000043030000-0x000000005fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.4
[ 0.000000] percpu: Embedded 17 pages/cpu s30040 r8192 d31400 u69632
[ 0.000000] pcpu-alloc: s30040 r8192 d31400 u69632 alloc=17*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[ 0.000000] CPU features: detected: ARM erratum 843419
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129024
[ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n1 swiotlb=512
[ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 502064K/524288K available (8384K kernel code, 904K rwdata, 1416K rodata, 448K init, 308K bss, 22224K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: 0xffffffc008423cb4
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
[ 0.000000] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns
[ 0.008243] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=125000)
[ 0.018642] pid_max: default: 32768 minimum: 301
[ 0.023554] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.030900] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.040031] rcu: Hierarchical SRCU implementation.
[ 0.045310] smp: Bringing up secondary CPUs ...
[ 0.050206] Detected VIPT I-cache on CPU1
[ 0.050217] CPU features: SANITY CHECK: Unexpected variation in SYS_CNTFRQ_EL0. Boot CPU: 0x00000000bebc20, CPU1: 0x00000000000000
[ 0.050237] CPU features: Unsupported CPU feature variation detected.
[ 0.050268] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.050339] smp: Brought up 1 node, 2 CPUs
[ 0.083264] SMP: Total of 2 processors activated.
[ 0.087980] CPU features: detected: 32-bit EL0 Support
[ 0.093135] CPU features: detected: CRC32 instructions
[ 0.098320] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.106763] CPU: All CPU(s) started at EL2
[ 0.110876] alternatives: patching kernel code
[ 0.119803] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.129706] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.136665] pinctrl core: initialized pinctrl subsystem
[ 0.142784] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.149064] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.156198] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.163987] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.172223] thermal_sys: Registered thermal governor 'fair_share'
[ 0.172227] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.178339] thermal_sys: Registered thermal governor 'step_wise'
[ 0.184369] thermal_sys: Registered thermal governor 'user_space'
[ 0.190595] ASID allocator initialised with 65536 entries
[ 0.202503] pstore: Registered ramoops as persistent store backend
[ 0.208712] ramoops: using 0x10000@0x42ff0000, ecc: 0
[ 0.235398] cryptd: max_cpu_qlen set to 1000
[ 0.242316] SCSI subsystem initialized
[ 0.246285] libata version 3.00 loaded.
[ 0.251395] clocksource: Switched to clocksource arch_sys_counter
[ 0.258137] NET: Registered PF_INET protocol family
[ 0.263158] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.270938] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.279349] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.287127] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.294932] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear)
[ 0.302152] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.308611] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.315178] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.322326] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.328022] PCI: CLS 0 bytes, default 64
[ 0.334875] workingset: timestamp_bits=46 max_order=17 bucket_order=0
[ 0.344945] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.350810] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.393244] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.401907] mt7622-pinctrl 10211000.pinctrl: invalid group "pwm_ch7_2" for function "pwm"
[ 0.414740] mt-pmic-pwrap 10001000.pwrap: unexpected interrupt int=0x1
[ 0.429721] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.438513] printk: console [ttyS0] disabled
[ 0.463008] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 125, base_baud = 1562500) is a ST16650V2
[ 0.472332] printk: console [ttyS0] enabled
[ 0.472332] printk: console [ttyS0] enabled
[ 0.480697] printk: bootconsole [uart8250] disabled
[ 0.480697] printk: bootconsole [uart8250] disabled
[ 0.511266] 11004000.serial: ttyS1 at MMIO 0x11004000 (irq = 126, base_baud = 1562500) is a ST16650V2
[ 0.521458] 1100c000.serial: ttyS2 at MMIO 0x1100c000 (irq = 130, base_baud = 17499995) is a MediaTek BTIF
[ 0.531274] serial serial0: tty port ttyS2 registered
[ 0.537195] mtk_rng 1020f000.rng: registered RNG driver
[ 0.537336] random: crng init done
[ 0.549591] loop: module loaded
[ 0.552784] Loading iSCSI transport class v2.0-870.
[ 0.558820] mtk-ecc 1100e000.ecc: probed
[ 0.566431] spi-nand spi2.0: Fidelix SPI NAND was found.
[ 0.571800] spi-nand spi2.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[ 0.579931] mtk-snand 1100d000.spi: ECC strength: 4 bits per 512 bytes
[ 0.586745] 4 fixed-partitions partitions found on MTD device spi2.0
[ 0.593143] OF: Bad cell count for /spi@1100d000/flash@0/partitions
[ 0.599427] OF: Bad cell count for /spi@1100d000/flash@0/partitions
[ 0.605987] Creating 4 MTD partitions on "spi2.0":
[ 0.610782] 0x000000000000-0x000000080000 : "bl2"
[ 0.616734] 0x000000080000-0x0000001c0000 : "fip"
[ 0.623180] 0x0000001c0000-0x0000002c0000 : "factory"
[ 0.629724] 0x000000300000-0x000008000000 : "ubi"
[ 0.895024] mtk_soc_eth 1b100000.ethernet eth0: mediatek frame engine at 0xffffffc009440000, irq 141
[ 0.904954] i2c_dev: i2c /dev entries driver
[ 0.910531] mtk-wdt 10212000.watchdog: IRQ index 0 not found
[ 0.916393] mtk-wdt 10212000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[ 0.926484] NET: Registered PF_INET6 protocol family
[ 0.932582] Segment Routing with IPv6
[ 0.936261] In-situ OAM (IOAM) with IPv6
[ 0.940212] NET: Registered PF_PACKET protocol family
[ 0.945342] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 0.958515] 8021q: 802.1Q VLAN Support v1.8
[ 0.964078] pstore: Using crash dump compression: deflate
[ 0.980513] mtk-pcie 1a143000.pcie: host bridge /pcie@1a143000 ranges:
[ 0.987116] mtk-pcie 1a143000.pcie: Parsing ranges property...
[ 0.992971] mtk-pcie 1a143000.pcie: MEM 0x0020000000..0x0027ffffff -> 0x0020000000
[ 1.137821] mtk-pcie 1a143000.pcie: PCI host bridge to bus 0000:00
[ 1.144033] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.149519] pci_bus 0000:00: root bus resource [mem 0x20000000-0x27ffffff]
[ 1.156403] pci_bus 0000:00: scanning bus
[ 1.160617] pci 0000:00:00.0: [14c3:3258] type 01 class 0x060400
[ 1.166810] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x1ffffffff 64bit pref]
[ 1.176802] pci_bus 0000:00: fixups for bus
[ 1.181009] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 0
[ 1.187724] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.195809] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 1
[ 1.202936] pci_bus 0000:01: scanning bus
[ 1.207161] pci 0000:01:00.0: [14c3:7915] type 00 class 0x000280
[ 1.213356] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[ 1.220682] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
[ 1.228012] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
[ 1.235981] pci 0000:01:00.0: supports D1 D2
[ 1.240246] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.246885] pci 0000:01:00.0: PME# disabled
[ 1.251398] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.294846] pci_bus 0000:01: fixups for bus
[ 1.299055] pci_bus 0000:01: bus scan returning with max=01
[ 1.304666] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.311304] pci_bus 0000:00: bus scan returning with max=01
[ 1.316897] pci 0000:00:00.0: BAR 0: no space for [mem size 0x200000000 64bit pref]
[ 1.324552] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x200000000 64bit pref]
[ 1.332561] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff]
[ 1.339346] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit pref]
[ 1.347174] pci 0000:01:00.0: BAR 2: assigned [mem 0x20100000-0x20103fff 64bit pref]
[ 1.355001] pci 0000:01:00.0: BAR 4: assigned [mem 0x20104000-0x20104fff 64bit pref]
[ 1.362826] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.367788] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff]
[ 1.374720] pcieport 0000:00:00.0: assign IRQ: got 146
[ 1.379864] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
[ 1.385977] pcieport 0000:00:00.0: enabling bus mastering
[ 1.391418] mtk-pcie 1a143000.pcie: msi#0 address_hi 0x0 address_lo 0x44d6d0c0
[ 1.398830] pcieport 0000:00:00.0: PME: Signaling with IRQ 146
[ 1.404775] pcieport 0000:00:00.0: saving config space at offset 0x0 (reading 0x325814c3)
[ 1.412969] pcieport 0000:00:00.0: saving config space at offset 0x4 (reading 0x100006)
[ 1.420968] pcieport 0000:00:00.0: saving config space at offset 0x8 (reading 0x6040000)
[ 1.429057] pcieport 0000:00:00.0: saving config space at offset 0xc (reading 0x10000)
[ 1.436972] pcieport 0000:00:00.0: saving config space at offset 0x10 (reading 0xc)
[ 1.444625] pcieport 0000:00:00.0: saving config space at offset 0x14 (reading 0x0)
[ 1.452278] pcieport 0000:00:00.0: saving config space at offset 0x18 (reading 0x40010100)
[ 1.460535] pcieport 0000:00:00.0: saving config space at offset 0x1c (reading 0x4200000)
[ 1.468708] pcieport 0000:00:00.0: saving config space at offset 0x20 (reading 0x20102000)
[ 1.476972] pcieport 0000:00:00.0: saving config space at offset 0x24 (reading 0x0)
[ 1.484626] pcieport 0000:00:00.0: saving config space at offset 0x28 (reading 0x0)
[ 1.492279] pcieport 0000:00:00.0: saving config space at offset 0x2c (reading 0x0)
[ 1.499928] pcieport 0000:00:00.0: saving config space at offset 0x30 (reading 0x0)
[ 1.507581] pcieport 0000:00:00.0: saving config space at offset 0x34 (reading 0x50)
[ 1.515321] pcieport 0000:00:00.0: saving config space at offset 0x38 (reading 0x0)
[ 1.522974] pcieport 0000:00:00.0: saving config space at offset 0x3c (reading 0x20192)
[ 1.531535] mtk-pcie 1a145000.pcie: host bridge /pcie@1a145000 ranges:
[ 1.538089] mtk-pcie 1a145000.pcie: Parsing ranges property...
[ 1.543930] mtk-pcie 1a145000.pcie: MEM 0x0028000000..0x002fffffff -> 0x0028000000
[ 1.771468] mtk-pcie 1a145000.pcie: Port1 link down
[ 1.776550] mtk-pcie 1a145000.pcie: PCI host bridge to bus 0001:00
[ 1.782754] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 1.788243] pci_bus 0001:00: root bus resource [mem 0x28000000-0x2fffffff]
[ 1.795128] pci_bus 0001:00: scanning bus
[ 1.800902] pci_bus 0001:00: fixups for bus
[ 1.805091] pci_bus 0001:00: bus scan returning with max=00
[ 1.811268] mtk_hsdma 1b007000.dma-controller: MediaTek HSDMA driver registered
[ 1.862497] mt7530-mdio mdio-bus:00: configuring for fixed/2500base-x link mode
[ 1.872413] mt7530-mdio mdio-bus:00: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 1.880863] mt7530-mdio mdio-bus:00 lan1 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7531 PHY] (irq=147)
[ 1.901881] mt7530-mdio mdio-bus:00 lan2 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=148)
[ 1.922263] mt7530-mdio mdio-bus:00 lan3 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=149)
[ 1.942627] mt7530-mdio mdio-bus:00 lan4 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=150)
[ 1.963220] mt7530-mdio mdio-bus:00 wan (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7531 PHY] (irq=151)
[ 1.974521] DSA: tree 0 setup
[ 1.978407] UBI: auto-attach mtd3
[ 1.981783] ubi0: default fastmap pool size: 50
[ 1.986308] ubi0: default fastmap WL pool size: 25
[ 1.991090] ubi0: attaching mtd3
[ 2.293183] ubi0: scanning is finished
[ 2.302497] ubi0: attached mtd3 (name "ubi", size 125 MiB)
[ 2.308002] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 2.314897] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 2.321690] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 2.328644] ubi0: good PEBs: 1000, bad PEBs: 0, corrupted PEBs: 0
[ 2.334742] ubi0: user volume: 6, internal volumes: 1, max. volumes count: 128
[ 2.341965] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 848159461
[ 2.351003] ubi0: available PEBs: 0, total reserved PEBs: 1000, PEBs reserved for bad PEB handling: 20
[ 2.360323] ubi0: background thread "ubi_bgt0d" started, PID 514
[ 2.361845] FIT: Selected configuration: "config-1" (OpenWrt linksys_e8450-ubi)
[ 2.373661] FIT: kernel sub-image 0x00001000..0x004e68d7 "kernel-1" (ARM64 OpenWrt Linux-5.15.134)
[ 2.383590] FIT: flat_dt sub-image 0x004e7000..0x004ee712 "fdt-1" (ARM64 OpenWrt linksys_e8450-ubi device tree blob)
[ 2.394988] FIT: filesystem sub-image 0x004ef000..0x00967fff "rootfs-1" (ARM64 OpenWrt linksys_e8450-ubi rootfs)
[ 2.405773] FIT: selecting configured loadable "rootfs-1" to be root filesystem
[ 2.413080] ubiblock0_4: p1(rootfs-1)
[ 2.413274] block ubiblock0_4: created from ubi0:4(fit)
[ 2.425678] VFS: Mounted root (squashfs filesystem) readonly on device 259:0.
[ 2.433061] Freeing unused kernel memory: 448K
[ 2.471477] Run /sbin/init as init process
[ 2.475583] with arguments:
[ 2.478546] /sbin/init
[ 2.481250] with environment:
[ 2.484415] HOME=/
[ 2.486774] TERM=linux
[ 2.664587] init: Console is alive
[ 2.668122] init: - watchdog -
[ 3.050653] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.076003] usbcore: registered new interface driver usbfs
[ 3.081571] usbcore: registered new interface driver hub
[ 3.086924] usbcore: registered new device driver usb
[ 3.097356] xhci-mtk 1a0c0000.usb: xHCI Host Controller
[ 3.102647] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 1
[ 3.111692] xhci-mtk 1a0c0000.usb: hcc params 0x01403198 hci version 0x96 quirks 0x0000000000210010
[ 3.120775] xhci-mtk 1a0c0000.usb: irq 135, io mem 0x1a0c0000
[ 3.126650] xhci-mtk 1a0c0000.usb: xHCI Host Controller
[ 3.131889] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 2
[ 3.139286] xhci-mtk 1a0c0000.usb: Host supports USB 3.0 SuperSpeed
[ 3.146053] hub 1-0:1.0: USB hub found
[ 3.149911] hub 1-0:1.0: 2 ports detected
[ 3.154506] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.163110] hub 2-0:1.0: USB hub found
[ 3.166908] hub 2-0:1.0: 1 port detected
[ 3.175351] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.192944] init: - preinit -
[ 3.483228] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 3.493364] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 3.503268] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 3.515806] mt7530-mdio mdio-bus:00 lan1: configuring for phy/gmii link mode
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
f
- failsafe -
Generating 1024 bit rsa key, this may take a while...
Public key portion is:
ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgQCFfEn2MGmJcUQQZywCWIbaIHyIRc0MFtbZKB64gbNj4Q6Yb9beOjplZ2cNt01UppKy9kq7gwYQi4oV6TMd4DgsdF/hXYjrggR1ooGQsOcYTvTiChmYPyXjOicv3KcXdTbbH5m5OFMt7OKCLLpbEfPgfqXY4lvpCwCl1jqvbZzHFw== root@(none)
Fingerprint: SHA256:T616+BSbu8pqkpttQ73XKXcSnqETnrPNyKinPrnElqg
Generating 256 bit ed25519 key, this may take a while...
Public key portion is:
ssh-ed25519 AAAAC3NzaC1lZDI1NTE5AAAAIP0UpUnKgQU5a66cmjyXTrBzpU/zUTF9tDOeicEW8GQe root@(none)
Fingerprint: SHA256:ofJVsRaCSjj4H7Ge8JHlh9e/qgdRfxexvNwQm4dcCh8
BusyBox v1.36.1 (2023-10-09 21:45:35 UTC) built-in shell (ash)
ash: can't access tty; job control turned off
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt 23.05.0, r23497-6637af95aa
-----------------------------------------------------
================= FAILSAFE MODE active ================
special commands:
* firstboot reset settings to factory defaults
* mount_root mount root-partition with config files
after mount_root:
* passwd change root's password
* /etc/config directory with config files
for more help see:
https://openwrt.org/docs/guide-user/troubleshooting/
- failsafe_and_factory_reset
- root_password_reset
=======================================================
root@(none):/#