Hello,
Thank you. I could flash the firmware trough OEM webinterface without problems (rebooted to OpenWrt with LUCI).
Here are all the things I could test:
-
LED works correctly. However, there are multiple options (mt76-phy0, rt2800soc-phy1::asoc, rt2800soc-phy1::quality, rt2800soc-phy1::radio, white:wifi). The last one is associated to the whit LED
-
Not all space is used (should be 8MB, no?). Problem with the mtd layout definition?
Filesystem Size Used Available Use% Mounted on
/dev/root 3.0M 3.0M 0 100% /rom
tmpfs 28.7M 236.0K 28.5M 1% /tmp
tmpfs 28.7M 56.0K 28.7M 0% /tmp/root
tmpfs 512.0K 0 512.0K 0% /dev
/dev/mtdblock6 2.9M 176.0K 2.7M 6% /overlay
overlayfs:/overlay 2.9M 176.0K 2.7M 6% /
And half of the RAM is used for /tmp. I supose is the default behaviour
- The default VLAN config is in the reverse order. Port 2 should be untagged for WAN instead for LAN
And LAN interface is bridged with eth0. I think it should be with eth0.1
-
Wifi works corretly. 2ghz and 5ghz seems to be stable.
-
A dmesg during all the tests. For the case
[ 0.000000] Linux version 5.4.75 (user@OpenWRT-build) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r14926-41b867165d)) #0 Thu Nov 12 17:21:55 2020
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Comfast CF-E538AC
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] Normal zone: 144 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.000000] Writing ErrCtl register=00035990
[ 0.000000] Readback ErrCtl register=00035990
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 57568K/65536K available (4581K kernel code, 204K rwdata, 1020K rodata, 1228K init, 205K bss, 7968K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] random: get_random_bytes called from start_kernel+0x32c/0x518 with crng_init=0
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.007591] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
[ 0.045490] pid_max: default: 32768 minimum: 301
[ 0.050173] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.057232] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.071385] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.080866] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.087562] pinctrl core: initialized pinctrl subsystem
[ 0.093233] NET: Registered protocol family 16
[ 0.359737] PCI host bridge /pcie@10140000 ranges:
[ 0.364353] MEM 0x0000000020000000..0x000000002fffffff
[ 0.369412] IO 0x0000000010160000..0x000000001016ffff
[ 0.397960] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.403439] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.409774] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.415202] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.421540] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.426888] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.433621] PCI host bridge to bus 0000:00
[ 0.437604] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[ 0.444227] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 0.449975] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.456566] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.464305] pci 0000:00:00.0: [1814:0801] type 01 class 0x060400
[ 0.470125] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 0.476185] pci 0000:00:00.0: reg 0x14: [mem 0x20200000-0x2020ffff]
[ 0.482346] pci 0000:00:00.0: supports D1
[ 0.486169] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.493846] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[ 0.499730] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 0.506314] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.512897] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.520638] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.527043] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[ 0.533469] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 0.539865] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 0.546627] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[ 0.553227] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
[ 0.560239] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[ 0.566841] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
[ 0.573952] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
[ 0.580946] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.585764] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
[ 0.592352] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref]
[ 0.599472] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[ 0.614739] clocksource: Switched to clocksource systick
[ 0.621325] NET: Registered protocol family 2
[ 0.626467] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.634618] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.642026] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.648869] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.655185] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.661540] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.668593] NET: Registered protocol family 1
[ 0.672874] PCI: CLS 80 bytes, default 32
[ 0.679859] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.688084] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[ 0.702791] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.708404] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.736350] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.743763] printk: console [ttyS0] disabled
[ 0.747976] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.757592] printk: console [ttyS0] enabled
[ 0.766062] printk: bootconsole [early0] disabled
[ 0.781899] spi spi0.0: force spi mode3
[ 0.796313] spi-nor spi0.0: s25fl064k (8192 Kbytes)
[ 0.801363] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.807857] Creating 4 MTD partitions on "spi0.0":
[ 0.812765] 0x000000000000-0x000000030000 : "u-boot"
[ 0.818955] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.825424] 0x000000040000-0x000000050000 : "factory"
[ 0.831729] 0x000000050000-0x000000800000 : "firmware"
[ 0.841555] 2 uimage-fw partitions found on MTD device firmware
[ 0.847683] Creating 2 MTD partitions on "firmware":
[ 0.852771] 0x000000000000-0x0000001d98b5 : "kernel"
[ 0.858998] 0x0000001d98b5-0x0000007b0000 : "rootfs"
[ 0.865029] mtd: device 5 (rootfs) set to be root filesystem
[ 0.872736] 1 squashfs-split partitions found on MTD device rootfs
[ 0.879143] 0x0000004c9000-0x0000007b0000 : "rootfs_data"
[ 0.886618] libphy: Fixed MDIO Bus: probed
[ 0.900630] gsw: setting port4 to gmac mode
[ 0.905442] libphy: mdio: probed
[ 0.910825] mtk_soc_eth 10100000.ethernet: connected port 4 to PHY at mdio-bus:04 [uid=001cc916, driver=Generic PHY]
[ 0.921867] mtk_soc_eth 10100000.ethernet: connected port 5 to PHY at mdio-bus:05 [uid=001cc916, driver=Generic PHY]
[ 0.932858] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 0.939639] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 0.948661] rt2880_wdt 10000120.watchdog: Initialized
[ 0.955398] NET: Registered protocol family 10
[ 0.965310] Segment Routing with IPv6
[ 0.969293] NET: Registered protocol family 17
[ 0.973924] 8021q: 802.1Q VLAN Support v1.8
[ 0.995932] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 1.010094] Freeing unused kernel memory: 1228K
[ 1.014747] This architecture does not have kernel memory protection.
[ 1.021321] Run /sbin/init as init process
[ 1.206697] random: fast init done
[ 2.681975] init: Console is alive
[ 2.685878] init: - watchdog -
[ 4.602439] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.972419] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.982209] init: - preinit -
[ 6.882806] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.975969] random: jshn: uninitialized urandom read (4 bytes read)
[ 7.134376] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.038950] 8021q: adding VLAN 0 to HW filter on device eth0
[ 8.111864] urandom_read: 4 callbacks suppressed
[ 8.111873] random: procd: uninitialized urandom read (4 bytes read)
[ 8.767713] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 8.779661] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 8.897456] procd: - early -
[ 8.900712] procd: - watchdog -
[ 9.097014] procd: - watchdog -
[ 9.100603] procd: - ubus -
[ 9.291343] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.299729] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.314921] procd: - init -
[ 10.522115] kmodloader: loading kernel modules from /etc/modules.d/*
[ 10.791205] Loading modules backported from Linux version v5.8-0-gbcf876870b95
[ 10.798665] Backport generated by backports.git v5.8-1-0-g79400d9e
[ 10.868393] xt_time: kernel timezone is -0000
[ 10.901361] urngd: jent-rng init failed, err: 2
[ 11.047700] mt76x2e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4
[ 11.054384] mt76x2e 0000:01:00.0: ASIC revision: 76120044
[ 11.131691] mt76x2e 0000:01:00.0: ROM patch build: 20141115060606a
[ 11.143912] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
[ 11.149591] mt76x2e 0000:01:00.0: Build: 1
[ 11.153797] mt76x2e 0000:01:00.0: Build Time: 201507311614____
[ 11.165098] mt76x2e 0000:01:00.0: Firmware running!
[ 11.172790] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 11.262571] PPP generic driver version 2.4.2
[ 11.270856] NET: Registered protocol family 24
[ 11.337183] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[ 11.344595] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[ 11.352543] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 11.359724] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 11.452633] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 20.329524] random: crng init done
[ 41.717536] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 41.733688] jffs2_build_filesystem(): unlocking the mtd device...
[ 41.733771] done.
[ 41.742094] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 42.412046] 8021q: adding VLAN 0 to HW filter on device eth0
[ 42.471567] br-lan: port 1(eth0.2) entered blocking state
[ 42.477169] br-lan: port 1(eth0.2) entered disabled state
[ 42.483101] device eth0.2 entered promiscuous mode
[ 42.488049] device eth0 entered promiscuous mode
[ 47.192119] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 47.208585] br-lan: port 1(eth0.2) entered blocking state
[ 47.214155] br-lan: port 1(eth0.2) entered forwarding state
[ 47.233129] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 47.545687] mtk_soc_eth 10100000.ethernet eth0: port 4 link up (1000Mbps/Full duplex)
[ 76.381041] done.
[ 76.383083] jffs2: notice: (1805) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 76.629322] overlayfs: upper fs does not support tmpfile.
[ 85.636090] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (100Mbps/Full duplex)
[ 131.160005] ieee80211 phy1: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration start
[ 131.168726] ieee80211 phy1: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration end
[ 133.618533] ieee80211 phy1: rt2800_loft_iq_calibration: Info - LOFT Calibration Done!
[ 134.131704] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration Start!
[ 134.153015] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration Done! CH = 0, (gain= 1, phase=3e)
[ 134.163258] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration Start!
[ 134.184555] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration Done! CH = 1, (gain= f, phase=3f)
[ 134.193914] ieee80211 phy1: rt2800_loft_iq_calibration: Info - TX IQ Calibration Done!
[ 134.703445] ieee80211 phy1: rt2800_rxiq_calibration: Warning - Wait MAC Status to MAX !!!
[ 135.210482] ieee80211 phy1: rt2800_rxiq_calibration: Info - RXIQ G_imb=2, Ph_rx=-2
[ 135.230924] ieee80211 phy1: rt2800_rxiq_calibration: Info - RXIQ G_imb=-1, Ph_rx=3
[ 135.289319] br-lan: port 2(wlan1) entered blocking state
[ 135.294836] br-lan: port 2(wlan1) entered disabled state
[ 135.300705] device wlan1 entered promiscuous mode
[ 135.839825] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 135.846596] br-lan: port 2(wlan1) entered blocking state
[ 135.852082] br-lan: port 2(wlan1) entered forwarding state
[ 190.745263] br-lan: port 3(wlan0) entered blocking state
[ 190.750780] br-lan: port 3(wlan0) entered disabled state
[ 190.756646] device wlan0 entered promiscuous mode
[ 192.556703] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 192.563538] br-lan: port 3(wlan0) entered blocking state
[ 192.569022] br-lan: port 3(wlan0) entered forwarding state
[ 387.387434] br-lan: port 4(eth0) entered blocking state
[ 387.392855] br-lan: port 4(eth0) entered disabled state
[ 387.398741] br-lan: port 4(eth0) entered blocking state
[ 387.404144] br-lan: port 4(eth0) entered forwarding state
[ 387.411134] device eth0.2 left promiscuous mode
[ 387.416041] br-lan: port 1(eth0.2) entered disabled state
[ 422.896245] br-lan: port 1(eth0.1) entered blocking state
[ 422.901862] br-lan: port 1(eth0.1) entered disabled state
[ 422.907911] device eth0.1 entered promiscuous mode
[ 422.913188] br-lan: port 1(eth0.1) entered blocking state
[ 422.918774] br-lan: port 1(eth0.1) entered forwarding state
[ 422.954518] br-lan: port 4(eth0) entered disabled state
[ 422.980260] device eth0.1 left promiscuous mode
[ 422.984975] device eth0 left promiscuous mode
[ 422.989680] br-lan: port 1(eth0.1) entered disabled state
[ 423.129471] br-lan: port 1(eth0.1) entered blocking state
[ 423.135063] br-lan: port 1(eth0.1) entered disabled state
[ 423.141074] device eth0.1 entered promiscuous mode
[ 423.146016] device eth0 entered promiscuous mode
[ 423.151160] br-lan: port 1(eth0.1) entered blocking state
[ 423.156749] br-lan: port 1(eth0.1) entered forwarding state
[ 490.826025] device wlan0 left promiscuous mode
[ 490.830820] br-lan: port 3(wlan0) entered disabled state
[ 491.294031] device wlan1 left promiscuous mode
[ 491.298931] br-lan: port 2(wlan1) entered disabled state
[ 493.912748] ieee80211 phy1: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration start
[ 493.921459] ieee80211 phy1: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration end
[ 495.664361] ieee80211 phy1: rt2800_loft_iq_calibration: Info - LOFT Calibration Done!
[ 495.676224] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration Start!
[ 495.697572] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration Done! CH = 0, (gain= 0, phase=3e)
[ 495.707807] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration Start!
[ 495.729114] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration Done! CH = 1, (gain= 1, phase= 0)
[ 495.738471] ieee80211 phy1: rt2800_loft_iq_calibration: Info - TX IQ Calibration Done!
[ 495.759972] ieee80211 phy1: rt2800_rxiq_calibration: Info - RXIQ G_imb=2, Ph_rx=-1
[ 495.777967] ieee80211 phy1: rt2800_rxiq_calibration: Warning - RXIQ calibration FAIL
[ 495.802001] br-lan: port 2(wlan1) entered blocking state
[ 495.807504] br-lan: port 2(wlan1) entered disabled state
[ 495.813411] device wlan1 entered promiscuous mode
[ 495.928380] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 495.935188] br-lan: port 2(wlan1) entered blocking state
[ 495.940652] br-lan: port 2(wlan1) entered forwarding state
[ 496.004801] br-lan: port 3(wlan0) entered blocking state
[ 496.010326] br-lan: port 3(wlan0) entered disabled state
[ 496.016403] device wlan0 entered promiscuous mode
[ 496.021482] br-lan: port 3(wlan0) entered blocking state
[ 496.026949] br-lan: port 3(wlan0) entered forwarding state
[ 496.267030] br-lan: port 3(wlan0) entered disabled state
[ 524.661326] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 524.668149] br-lan: port 3(wlan0) entered blocking state
[ 524.673636] br-lan: port 3(wlan0) entered forwarding state
[ 544.384902] device wlan1 left promiscuous mode
[ 544.389686] br-lan: port 2(wlan1) entered disabled state
[ 544.497281] device wlan0 left promiscuous mode
[ 544.502059] br-lan: port 3(wlan0) entered disabled state
[ 547.665924] br-lan: port 2(wlan0) entered blocking state
[ 547.671442] br-lan: port 2(wlan0) entered disabled state
[ 547.677335] device wlan0 entered promiscuous mode
[ 547.732743] ieee80211 phy1: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration start
[ 547.741463] ieee80211 phy1: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration end
[ 549.575666] ieee80211 phy1: rt2800_loft_iq_calibration: Info - LOFT Calibration Done!
[ 549.587571] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration Start!
[ 549.608902] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration Done! CH = 0, (gain= f, phase=3e)
[ 549.619145] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration Start!
[ 549.640457] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration Done! CH = 1, (gain= f, phase=3f)
[ 549.649821] ieee80211 phy1: rt2800_loft_iq_calibration: Info - TX IQ Calibration Done!
[ 549.671827] ieee80211 phy1: rt2800_rxiq_calibration: Info - RXIQ G_imb=2, Ph_rx=-1
[ 549.689822] ieee80211 phy1: rt2800_rxiq_calibration: Warning - RXIQ calibration FAIL
[ 549.721469] br-lan: port 3(wlan1) entered blocking state
[ 549.726979] br-lan: port 3(wlan1) entered disabled state
[ 549.732861] device wlan1 entered promiscuous mode
[ 550.454805] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 550.461683] br-lan: port 3(wlan1) entered blocking state
[ 550.467179] br-lan: port 3(wlan1) entered forwarding state
[ 556.242877] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 556.249700] br-lan: port 2(wlan0) entered blocking state
[ 556.255184] br-lan: port 2(wlan0) entered forwarding state
Things I couldn't test:
- Gigabit speeds. I only could try with Fast Ethernet.
- The button
Br,
ValentÃn 