Hello,
I have a TP-Link MR6400 v2.
I installed the open wrt factory image via tftp boot and afterwards the open wrt sysupgrade.
Then I also installed LUCI.
I have a Sim Card and want to configure the SIM Interface. But i can't find a way to do it in the LUCI GUI.
I checked the cofiguration file aswell but I am not sure how to configure it.
In some guidelines i found that the SIM module is accessable via 192.168.0.1 but that didn't work for me.
I found the guild below but it seems for a dongle / usb con.
https://wiki.openwrt.org/doc/recipes/ltedongle
Below also the dmesg:
(in the highlighted line there seem to be a GSM)
(also below the output from cat /sys/kernel/debug/usb/devices )
Incase anyone could guide me in the right direction or has any tips i would appreciate it!
Thanks a lot for your time!
BusyBox v1.28.4 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r7558-a5c3bba
-----------------------------------------------------
root@OpenWrt:~# dmesg
[ 0.000000] Linux version 4.9.111 (buildbot@crazyhorse) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7545-354de22) ) #0 Wed Jul 25 10:15:45 2018
[ 0.000000] MyLoader: sysp=f5ede6ad, boardp=25a7a5a9, parts=9ca2ada1
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 804e1e64, node_mem_map 81000020
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: board=TL-MR6400 console=ttyS0,115200 rootfstype=squashfs noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 59380K/65536K available (3586K kernel code, 177K rwdata, 856K rodata, 300K init, 219K bss, 6156K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:650.000MHz, DDR:390.844MHz, AHB:216.666MHz, Ref:25.000MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5880801374 ns
[ 0.000009] sched_clock: 32 bits at 325MHz, resolution 3ns, wraps every 6607641598ns
[ 0.008270] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688)
[ 0.071113] pid_max: default: 32768 minimum: 301
[ 0.076094] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.083074] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.093401] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.103805] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.111595] NET: Registered protocol family 16
[ 0.118002] MIPS: machine is TP-LINK TL-MR6400
[ 0.620171] clocksource: Switched to clocksource MIPS
[ 0.626636] NET: Registered protocol family 2
[ 0.632293] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.639662] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.646435] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.653257] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.659436] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.666371] NET: Registered protocol family 1
[ 0.671031] PCI: CLS 0 bytes, default 32
[ 0.674926] Crashlog allocated RAM at address 0x3f00000
[ 0.681595] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.695729] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.701928] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.721866] io scheduler noop registered
[ 0.726006] io scheduler deadline registered (default)
[ 0.731933] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.741425] console [ttyS0] disabled
[ 0.765354] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[ 0.774464] console [ttyS0] enabled
[ 0.782024] bootconsole [early0] disabled
[ 0.796839] m25p80 spi0.0: found s25fl064k, expected w25q64
[ 0.812012] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[ 0.817336] 5 tp-link partitions found on MTD device spi0.0
[ 0.823134] Creating 5 MTD partitions on "spi0.0":
[ 0.828086] 0x000000000000-0x000000020000 : "u-boot"
[ 0.834778] 0x000000020000-0x00000019ef10 : "kernel"
[ 0.841758] 0x00000019ef10-0x0000007f0000 : "rootfs"
[ 0.848575] mtd: device 2 (rootfs) set to be root filesystem
[ 0.854543] 1 squashfs-split partitions found on MTD device rootfs
[ 0.860952] 0x000000430000-0x0000007f0000 : "rootfs_data"
[ 0.868298] 0x0000007f0000-0x000000800000 : "art"
[ 0.875054] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.883194] libphy: Fixed MDIO Bus: probed
[ 0.911380] libphy: ag71xx_mdio: probed
[ 1.542722] ag71xx-mdio.1: Found an AR934X built-in switch
[ 1.596076] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.233109] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
[ 2.243287] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.251511] NET: Registered protocol family 10
[ 2.260424] NET: Registered protocol family 17
[ 2.265094] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.278643] 8021q: 802.1Q VLAN Support v1.8
[ 2.284801] hctosys: unable to open rtc device (rtc0)
[ 2.295246] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.304683] Freeing unused kernel memory: 300K
[ 2.309279] This architecture does not have kernel memory protection.
[ 2.540180] random: fast init done
[ 3.017657] init: Console is alive
[ 3.021541] init: - watchdog -
[ 4.100015] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.163083] usbcore: registered new interface driver usbfs
[ 4.168839] usbcore: registered new interface driver hub
[ 4.174512] usbcore: registered new device driver usb
[ 4.185873] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.194521] ehci-platform: EHCI generic platform driver
[ 4.200025] ehci-platform ehci-platform: EHCI Host Controller
[ 4.206080] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 4.216390] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 4.250209] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 4.257649] hub 1-0:1.0: USB hub found
[ 4.261959] hub 1-0:1.0: 1 port detected
[ 4.267059] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.277436] init: - preinit -
[ 5.008527] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 5.037412] random: procd: uninitialized urandom read (4 bytes read)
[ 6.642636] eth0: link up (1000Mbps/Full duplex)
[ 6.647454] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 8.390750] jffs2: notice: (410) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 8.412373] mount_root: switching to jffs2 overlay
[ 8.454173] urandom-seed: Seeding with /etc/urandom.seed
[ 8.636073] eth0: link down
[ 8.655456] procd: - early -
[ 8.658557] procd: - watchdog -
[ 9.231172] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.359059] procd: - watchdog -
[ 9.363221] procd: - ubus -
[ 9.393251] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.419791] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.428684] procd: - init -
[ 9.825589] kmodloader: loading kernel modules from /etc/modules.d/*
[ 9.838056] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 9.857854] usbcore: registered new interface driver cdc_wdm
[ 9.866371] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[ 9.874722] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 9.885102] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.901128] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 9.961554] usbcore: registered new interface driver usbserial
[ 9.967681] usbcore: registered new interface driver usbserial_generic
[ 9.974590] usbserial: USB Serial support registered for generic
[ 10.004267] xt_time: kernel timezone is -0000
[ 10.011260] usbcore: registered new interface driver cdc_ether
[ 10.088808] PPP generic driver version 2.4.2
[ 10.096179] NET: Registered protocol family 24
[ 10.106473] usbcore: registered new interface driver qmi_wwan
[ 10.115437] usbcore: registered new interface driver rndis_host
[ 10.153411] usbcore: registered new interface driver option
**[ 10.159275] usbserial: USB Serial support registered for GSM modem (1-port)**
[ 10.192099] ath: EEPROM regdomain: 0x0
[ 10.192111] ath: EEPROM indicates default country code should be used
[ 10.192114] ath: doing EEPROM country->regdmn map search
[ 10.192131] ath: country maps to regdmn code: 0x3a
[ 10.192137] ath: Country alpha2 being used: US
[ 10.192140] ath: Regpair used: 0x3a
[ 10.203821] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 10.208519] ieee80211 phy0: Atheros AR9531 Rev:2 mem=0xb8100000, irq=47
[ 10.318182] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 11.170268] usb 1-1: new high-speed USB device number 3 using ehci-platform
[ 11.410729] rndis_host 1-1:1.0 usb0: register 'rndis_host' at usb-ehci-platform-1, RNDIS device, 2e:e7:f4:0d:b2:d0
**[ 11.451807] option 1-1:1.4: GSM modem (1-port) converter detected**
**[ 11.458470] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0**
**[ 11.466613] option 1-1:1.5: GSM modem (1-port) converter detected**
**[ 11.473260] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1**
[ 23.451273] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 23.481752] br-lan: port 1(eth0.1) entered blocking state
[ 23.487347] br-lan: port 1(eth0.1) entered disabled state
[ 23.493427] device eth0.1 entered promiscuous mode
[ 23.498382] device eth0 entered promiscuous mode
[ 23.590622] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 23.634565] br-lan: port 2(eth1) entered blocking state
[ 23.639981] br-lan: port 2(eth1) entered disabled state
[ 23.645877] device eth1 entered promiscuous mode
[ 25.111732] eth0: link up (1000Mbps/Full duplex)
[ 25.116567] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 25.140364] br-lan: port 1(eth0.1) entered blocking state
[ 25.145963] br-lan: port 1(eth0.1) entered forwarding state
[ 25.159911] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
root@OpenWrt:~# cat /sys/kernel/debug/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 1, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 4.09
S: Manufacturer=Linux 4.9.111 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2357 ProdID=000d Rev= 3.18
S: Manufacturer=TP-Link Technologies Co., Ltd.
S: Product=MR6400
S: SerialNumber=b6dd5e30
C:* #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=03
I:* If#= 0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=88(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us