I am looking to add support for TL-WA850RE v5. I cracked one open and I have a pictures of the chip and also the serial output.
I am new to this, so it will be helpful to know what the next steps are.
The chips
MEDIATEK MT7628NN
1740-AJCSL
EAP11483
Zentel A3R56E40ABF-8E
740ZEN51
7A005784G-F
Serial Information:
pin 1: TX
pin 2 GND
pin 3: VCC
pin 4: RX
Rate: 57600 8N1
This is a serial dump from a clean boot of a device that has not been setup yet.
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2018.08.25 13:05:16 =~=~=~=~=~=~=~=~=~=~=~=
[04060C0B][04060C0C]
DDR Calibration DQS reg = 00008988
U-Boot 1.1.3 (Nov 16 2017 - 10:04:46)
Board: Ralink APSoC DRAM: 32 MB
relocate_code Pointer at: 81f8c000
flash manufacture id: c8, device id 40 16
find flash: GD25Q32B
*** Warning - bad CRC, using default environment
board_init_r : load_addr is 81000000
============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 256 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 32 MBytes
Flash component: SPI Flash
Date:Nov 16 2017 Time:10:04:46
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 575 MHZ ####
estimate memory size =32 Mbytes
RESET MT7628 PHY!!!!!!rt305x_esw_init, 0x64 value:0x5540554
rt305x_esw_init, after tp, 0x64 value:0x5540555
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
a: Load firmware then write to Flash via http(192.168.0.254).
default: 3
You choosed 3
0
3: System Boot system code via Flash.
## Booting image at bc020000 ...
text base: 80000000
entry point: 8000c150
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c150) ...
## Giving linux memsize in MB, 32
Starting kernel ...
LINUX started...
THIS IS ASIC
Linux version 2.6.36 (zhemeda@zmd7017) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 Thu Nov 16 10:07:56 CST 2017
The CPU feqenuce set to 580 MHz
CPU revision is: 00019655 (MIPS 24Kc)
Software DMA cache coherency
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock3
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=00058e27
Readback ErrCtl register=00058e27
Memory: 29836k/32768k available (1889k kernel code, 2880k reserved, 423k data, 132k init, 0k highmem)
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:128
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
RALINK_GPIOMODE = 571544c5
RALINK_GPIOMODE = 571444c5
***** Xtal 25MHz *****
start PCIe register access
RALINK_RSTCTRL = 2400000
RALINK_CLKCFG1 = fdbfffc0
*************** MT7628 PCIe RC mode *************
PCIE0 no card, disable it(RST&CLK)
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 58
io scheduler noop registered (default)
Ralink gpio driver initialized
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
flash manufacture id: c8, device id 40 16
GD25Q32B(c8 40160000) (4096 Kbytes)
mtd .name = raspi, .size = 0x00400000 (4M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 5 MTD partitions on "raspi":
0x000000000000-0x000000400000 : "ALL"
0x000000000000-0x000000020000 : "fs-uboot"
0x000000020000-0x000000100000 : "os-image"
0x000000100000-0x0000003c2000 : "file-system"
mtd: partition "file-system" doesn't end on an erase block -- force read-only
0x0000003f0000-0x000000400000 : "radio"
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
Freeing unused kernel memory: 132k freed
init started: BusyBox v1.19.4 (2017-11-16 10:09:30 CST)
starting pid 17, tty '': '/etc/rc.d/rcS'
This Board use 2.6.36.x
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x43288098
Ralink APSoC Ethernet Driver Initilization. v3.1 256 rx/tx descriptors allocated, mtu = 1500!
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x432880cd
PROC INIT OK!
Lan Domain: tplinkrepeater.net
Lan Domain: www.tplinkrepeater.net
tp_dhcp_hook: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
device eth2 entered promiscuous mode
====>>>>========================================
====>>>>1163198464
====>>>>Original SID is
====>>>>4-34
====>>>>5-35
====>>>>5-35
====>>>>5-35
====>>>>0-30
====>>>>0-30
====>>>>0-30
====>>>>0-30
====>>>>Original WIFIRegion is DE
====>>>>Changed WIFIRegion to DE
[ucEthernet_init:134]ERROR product_id= 08500500
====>>>>caldata: 76 28 DE AD 76 12 DE AD
====>>>>default mac is b0-4e-26-de-cb-22
====>>>>default mac is b0-4e-26-de-cb-22
[main:539]send a pipe message.
[daemonize:327]recv a pipe message.
[smartip_get_wifi_update_eth_bridge_status 514] open /tmp/wifi_update_eth_and_bridge file failed
Raeth v3.1 (Tasklet)
phy_tx_ring = 0x01fc7000, tx_ring = 0xa1fc7000
phy_rx_ring0 = 0x01fc8000, rx_ring0 = 0xa1fc8000
--->>>>driver rt305x_esw_init 0x64 value:0x5540555
Gpio Mode Value: 571444c5
Gpio Mode Value: 571444c5
GMAC1_MAC_ADRH -- : 0x0000b04e
GMAC1_MAC_ADRL -- : 0x26decb22
RT305x_ESW: Link Status Changed
httpMudCreate: MUD 0x4aba50 was created
httpServerCreate: try to add port 80
[GPIOD][gpio_set_led_wifi_sta_850rev5:351]--->>>pri:255 now:0
[GPIOD][gpio_set_led_wifi_sta_850rev5:360]-->>>off led, pri:255 now:0
starting pid 113, tty '': '/sbin/getty ttyS1 57600'
br0: port 1(eth2) entering forwarding state
br0: port 1(eth2) entering forwarding state
TL-WA850RE login: MT7628-->
=== pAd = c050a000, size = 1384952 ===
<-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
<-- RTMPAllocAdapterBlock, Status=0
MT7628-->RtmpChipOpsHook(492): Not support for HIF_MT yet!
MT7628-->mt7628_init()-->
MT7628-->mt7628_init(FW(8a00), HW(8a01), CHIPID(7628))
MT7628-->e2.bin mt7628_init(1135)::(2), pChipCap->fw_len(63888)
MT7628-->mt_bcn_buf_init(218): Not support for HIF_MT yet!
MT7628--><--mt7628_init()
MT7628-->TX_BCN DESC a0e56000 size = 320
MT7628-->RX[0] DESC a0e5a000 size = 1024
MT7628-->RX[1] DESC a0e5b000 size = 1024
MT7628-->E2pAccessMode=2
MT7628-->CountryCode=DE
MT7628-->cfg_mode=9
MT7628-->cfg_mode=9
MT7628-->wmode_band_equal(): Band Equal!
MT7628-->AndesSendCmdMsg: Could not send in band command due to diable fRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD
MT7628-->APSDCapable[0]=1
MT7628-->APSDCapable[1]=1
MT7628-->APSDCapable[2]=1
MT7628-->APSDCapable[3]=1
MT7628-->APSDCapable[4]=1
MT7628-->APSDCapable[5]=1
MT7628-->APSDCapable[6]=1
MT7628-->APSDCapable[7]=1
MT7628-->APSDCapable[8]=1
MT7628-->APSDCapable[9]=1
MT7628-->APSDCapable[10]=1
MT7628-->APSDCapable[11]=1
MT7628-->APSDCapable[12]=1
MT7628-->APSDCapable[13]=1
MT7628-->APSDCapable[14]=1
MT7628-->APSDCapable[15]=1
MT7628-->default ApCliAPSDCapable[0]=1
MT7628-->Key1Str is Invalid key length(0) or Type(0)
MT7628-->Key2Str is Invalid key length(0) or Type(0)
MT7628-->Key3Str is Invalid key length(0) or Type(0)
MT7628-->Key4Str is Invalid key length(0) or Type(0)
MT7628-->Smart Carrier Sense = 1
MT7628-->RTMPSetSingleSKUParameters - the country region is 5.
MT7628-->RTMPSetSingleSKUParameters - country code is DE .
MT7628-->RTMPSetSingleSKUParameters - the country DFSType is 0.
MT7628-->Loading SKU file: /etc_ro/Wireless/RT2860/SingleSKU_2G_CE.dat
MT7628-->load fw image from fw_header_image
MT7628-->AndesMTLoadFwMethod1(2182)::pChipCap->fw_len(63888)
MT7628-->FW Version:MT7628-->2MT7628-->0MT7628-->1MT7628-->5MT7628-->1MT7628-->2MT7628-->0MT7628-->1MT7628-->MT7628-->MT7628-->
MT7628-->FW Build Date:MT7628-->2MT7628-->0MT7628-->1MT7628-->5MT7628-->1MT7628-->2MT7628-->0MT7628-->1MT7628-->1MT7628-->8MT7628-->3MT7628-->6MT7628-->4MT7628-->1MT7628-->MT7628-->
MT7628-->CmdAddressLenReq:(ret = 0)
MT7628-->CmdFwStartReq: override = 1, address = 1048576
MT7628-->CmdStartDLRsp: WiFI FW Download Success
MT7628-->MtAsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
efuse_probe: efuse = 10000012
MT7628-->RtmpChipOpsEepromHook::e2p_type=2, inf_Type=4
MT7628-->RtmpEepromGetDefault::e2p_dafault=2
MT7628-->RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 2
MT7628-->NVM is FLASH mode
MT7628-->1. Phy Mode = 14
MT7628-->Country Region from e2p = ffff
tssi_1_target_pwr_g_band = 34
MT7628-->2. Phy Mode = 14
MT7628-->3. Phy Mode = 14
MT7628-->NICInitPwrPinCfg(11): Not support for HIF_MT yet!
MT7628-->NICInitializeAsic(651): Not support rtmp_mac_sys_reset () for HIF_MT yet!
MT7628-->mt_mac_init()-->
MT7628-->MtAsicInitMac()-->
MT7628-->mt7628_init_mac_cr()-->
MT7628-->MtAsicSetMacMaxLen(1276): Set the Max RxPktLen=450!
MT7628--><--mt_mac_init()
MT7628--> WTBL Segment 1 info:
MT7628--> MemBaseAddr/FID:0x28000/0
MT7628--> EntrySize/Cnt:32/128
MT7628--> WTBL Segment 2 info:
MT7628--> MemBaseAddr/FID:0x40000/0
MT7628--> EntrySize/Cnt:64/128
MT7628--> WTBL Segment 3 info:
MT7628--> MemBaseAddr/FID:0x42000/64
MT7628--> EntrySize/Cnt:64/128
MT7628--> WTBL Segment 4 info:
MT7628--> MemBaseAddr/FID:0x44000/128
MT7628--> EntrySize/Cnt:32/128
MT7628-->AntCfgInit(2945): Not support for HIF_MT yet!
MT7628-->MCS Set = ff ff 00 00 01
MT7628-->MtAsicSetChBusyStat(861): Not support for HIF_MT yet!
MT7628-->[PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
MT7628-->MtAsicSetRalinkBurstMode(3059): Not support for HIF_MT yet!
MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
MT7628-->MtAsicSetTxPreamble(3038): Not support for HIF_MT yet!
MT7628-->CmdSlotTimeSet:(ret = 0)
MT7628-->The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
MT7628-->Main bssid = b0:4e:26:de:cb:23
<==== rt28xx_init, Status=0
MT7628-->@@@ ed_monitor_init : ===>
MT7628-->@@@ ed_monitor_init : <===
MT7628-->mt7628_set_ed_cca: TURN ON EDCCA mac 0x10618 = 0xd7c87d0f, EDCCA_Status=1
MT7628-->WiFi Startup Cost (ra0): 1.956s
MT7628-->
==== EDCCA CERT @@@ ed_status_read: EDCCA TH - H
pAd->ed_trigger_cnt : 0 > 20 || pAd->ed_big_rssi_stat : 0 < 50
====
device ra0 entered promiscuous mode
br0: port 2(ra0) entering forwarding state
br0: port 2(ra0) entering forwarding state
MT7628-->AddTxSType: already registered TxSType (PID = 32, Format = 0
MT7628-->The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
device apcli0 entered promiscuous mode
br0: port 3(apcli0) entering forwarding state
br0: port 3(apcli0) entering forwarding state
br0: port 3(apcli0) entering forwarding state
MT7628-->The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0x0
MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
MT7628-->tx_kickout_fail_count = 0
MT7628-->tx_timeout_fail_count = 0
MT7628-->rx_receive_fail_count = 0
MT7628-->alloc_cmd_msg = 191
MT7628-->free_cmd_msg = 191
br0: port 2(ra0) entering forwarding state
MT7628-->TX_BCN DESC a0e56000 size = 320
MT7628-->RX[0] DESC a0e5a000 size = 1024
MT7628-->RX[1] DESC a0e5b000 size = 1024
MT7628-->E2pAccessMode=2
MT7628-->CountryCode=DE
MT7628-->cfg_mode=9
MT7628-->cfg_mode=9
MT7628-->wmode_band_equal(): Band Equal!
MT7628-->AndesSendCmdMsg: Could not send in band command due to diable fRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD
MT7628-->APSDCapable[0]=1
MT7628-->APSDCapable[1]=1
MT7628-->APSDCapable[2]=1
MT7628-->APSDCapable[3]=1
MT7628-->APSDCapable[4]=1
MT7628-->APSDCapable[5]=1
MT7628-->APSDCapable[6]=1
MT7628-->APSDCapable[7]=1
MT7628-->APSDCapable[8]=1
MT7628-->APSDCapable[9]=1
MT7628-->APSDCapable[10]=1
MT7628-->APSDCapable[11]=1
MT7628-->APSDCapable[12]=1
MT7628-->APSDCapable[13]=1
MT7628-->APSDCapable[14]=1
MT7628-->APSDCapable[15]=1
MT7628-->default ApCliAPSDCapable[0]=1
MT7628-->Key1Str is Invalid key length(0) or Type(0)
MT7628-->Key2Str is Invalid key length(0) or Type(0)
MT7628-->Key3Str is Invalid key length(0) or Type(0)
MT7628-->Key4Str is Invalid key length(0) or Type(0)
MT7628-->Smart Carrier Sense = 1
MT7628-->RTMPSetSingleSKUParameters - the country region is 5.
MT7628-->RTMPSetSingleSKUParameters - country code is DE .
MT7628-->RTMPSetSingleSKUParameters - the country DFSType is 0.
MT7628-->Loading SKU file: /etc_ro/Wireless/RT2860/SingleSKU_2G_CE.dat
MT7628-->load fw image from fw_header_image
MT7628-->AndesMTLoadFwMethod1(2182)::pChipCap->fw_len(63888)
MT7628-->FW Version:MT7628-->2MT7628-->0MT7628-->1MT7628-->5MT7628-->1MT7628-->2MT7628-->0MT7628-->1MT7628-->MT7628-->MT7628-->
MT7628-->FW Build Date:MT7628-->2MT7628-->0MT7628-->1MT7628-->5MT7628-->1MT7628-->2MT7628-->0MT7628-->1MT7628-->1MT7628-->8MT7628-->3MT7628-->6MT7628-->4MT7628-->1MT7628-->MT7628-->
MT7628-->CmdReStartDLRsp: WiFI FW Download Success
MT7628-->CmdAddressLenReq:(ret = 0)
MT7628-->CmdFwStartReq: override = 1, address = 1048576
MT7628-->CmdStartDLRsp: WiFI FW Download Success
MT7628-->MtAsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
efuse_probe: efuse = 10000012
MT7628-->RtmpChipOpsEepromHook::e2p_type=2, inf_Type=4
MT7628-->RtmpEepromGetDefault::e2p_dafault=2
MT7628-->RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 2
MT7628-->NVM is FLASH mode
MT7628-->1. Phy Mode = 14
MT7628-->Country Region from e2p = ffff
tssi_1_target_pwr_g_band = 34
MT7628-->2. Phy Mode = 14
MT7628-->3. Phy Mode = 14
MT7628-->NICInitPwrPinCfg(11): Not support for HIF_MT yet!
MT7628-->NICInitializeAsic(651): Not support rtmp_mac_sys_reset () for HIF_MT yet!
MT7628-->mt_mac_init()-->
MT7628-->MtAsicInitMac()-->
MT7628-->mt7628_init_mac_cr()-->
MT7628-->MtAsicSetMacMaxLen(1276): Set the Max RxPktLen=450!
MT7628--><--mt_mac_init()
MT7628--> WTBL Segment 1 info:
MT7628--> MemBaseAddr/FID:0x28000/0
MT7628--> EntrySize/Cnt:32/128
MT7628--> WTBL Segment 2 info:
MT7628--> MemBaseAddr/FID:0x40000/0
MT7628--> EntrySize/Cnt:64/128
MT7628--> WTBL Segment 3 info:
MT7628--> MemBaseAddr/FID:0x42000/64
MT7628--> EntrySize/Cnt:64/128
MT7628--> WTBL Segment 4 info:
MT7628--> MemBaseAddr/FID:0x44000/128
MT7628--> EntrySize/Cnt:32/128
MT7628-->AntCfgInit(2945): Not support for HIF_MT yet!
MT7628-->MCS Set = ff ff 00 00 01
MT7628-->MtAsicSetChBusyStat(861): Not support for HIF_MT yet!
MT7628-->[PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
MT7628-->MtAsicSetRalinkBurstMode(3059): Not support for HIF_MT yet!
MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
MT7628-->MtAsicSetTxPreamble(3038): Not support for HIF_MT yet!
MT7628-->The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
MT7628-->Main bssid = b0:4e:26:de:cb:23
<==== rt28xx_init, Status=0
MT7628-->@@@ ed_monitor_init : ===>
MT7628-->@@@ ed_monitor_init : <===
MT7628-->mt7628_set_ed_cca: TURN ON EDCCA mac 0x10618 = 0xd7c87d0f, EDCCA_Status=1
MT7628-->WiFi Startup Cost (ra0): 1.920s
MT7628-->
==== EDCCA CERT @@@ ed_status_read: EDCCA TH - H
pAd->ed_trigger_cnt : 0 > 20 || pAd->ed_big_rssi_stat : 0 < 50
====
br0: port 2(ra0) entering forwarding state
br0: port 2(ra0) entering forwarding state
MT7628-->AddTxSType: already registered TxSType (PID = 32, Format = 0
MT7628-->The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
br0: port 3(apcli0) entering forwarding state
br0: port 3(apcli0) entering forwarding state
MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0x0
MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
MT7628-->[PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
MT7628-->MtAsicSetRalinkBurstMode(3059): Not support for HIF_MT yet!
MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
MT7628-->MtAsicSetTxPreamble(3038): Not support for HIF_MT yet!
MT7628-->AddTxSType: already registered TxSType (PID = 32, Format = 0
MT7628-->The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
MT7628-->AddTxSType: already registered TxSType (PID = 6, Format = 0
MT7628-->AddTxSType: already registered TxSType (PID = 8, Format = 0
MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
MT7628-->Main bssid = b0:4e:26:de:cb:23
MT7628-->cfg_mode=9
MT7628-->wmode_band_equal(): Band Equal!
MT7628-->AddTxSType: already registered TxSType (PID = 32, Format = 0
MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0x0
MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
MT7628-->[PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
MT7628-->MtAsicSetRalinkBurstMode(3059): Not support for HIF_MT yet!
MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
MT7628-->MtAsicSetTxPreamble(3038): Not support for HIF_MT yet!
MT7628-->AddTxSType: already registered TxSType (PID = 32, Format = 0
MT7628-->The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
MT7628-->AddTxSType: already registered TxSType (PID = 6, Format = 0
MT7628-->AddTxSType: already registered TxSType (PID = 8, Format = 0
MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
MT7628-->Main bssid = b0:4e:26:de:cb:23
MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0x0
MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
MT7628-->[PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
MT7628-->MtAsicSetRalinkBurstMode(3059): Not support for HIF_MT yet!
MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
MT7628-->MtAsicSetTxPreamble(3038): Not support for HIF_MT yet!
MT7628-->AddTxSType: already registered TxSType (PID = 32, Format = 0
MT7628-->The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
MT7628-->AddTxSType: already registered TxSType (PID = 6, Format = 0
MT7628-->AddTxSType: already registered TxSType (PID = 8, Format = 0
MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
MT7628-->Main bssid = b0:4e:26:de:cb:23
ra0:rai0:eth2
Set: phy[0].reg[0] = 3900
Set: phy[1].reg[0] = 3900
Set: phy[2].reg[0] = 3900
Set: phy[3].reg[0] = 3900
Set: phy[4].reg[0] = 3900
Set: phy[0].reg[0] = 3300
Set: phy[1].reg[0] = 3300
Set: phy[2].reg[0] = 3300
Set: phy[3].reg[0] = 3300
Set: phy[4].reg[0] = 3300
Reset Mii Port Value Over.