Hey guys,
I'd like to update my AP6 420 with the OpenWrt software. I've just seen that it's not supported yet. What information do you need to update it? I've already taken it apart and seen that it has a Qualcomm IPQ5018 (001) installed. This processor is generally supported by Linksys, for example. Can I try installing this firmware?
Regards
Andreas
Here are the first lines of the serial edition
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1.1-00067
S - IMAGE_VARIANT_STRING=MAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002c1
B - 127 - PBL, Start
B - 1560 - bootable_media_detect_entry, Start
B - 1736 - bootable_media_detect_success, Start
B - 1741 - elf_loader_entry, Start
B - 10165 - auth_hash_seg_entry, Start
B - 10522 - auth_hash_seg_exit, Start
B - 175071 - elf_segs_hash_verify_entry, Start
B - 237770 - PBL, End
B - 192912 - SBL1, Start
B - 254248 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B - 262574 - clock_init, Start
D - 7320 - clock_init, Delta
B - 270016 - boot_flash_init, Start
D - 2775 - boot_flash_init, Delta
B - 274103 - boot_config_data_table_init, Start
D - 762 - boot_config_data_table_init, Delta - (575 Bytes)
B - 287249 - Boot Setting : 0x00030618
B - 290085 - CDT version:2,Platform ID:8,Major ID:4,Minor ID:0,Subtype:4
B - 300516 - sbl1_ddr_set_params, Start
B - 305640 - Pre_DDR_clock_init, Start
B - 307440 - Pre_DDR_clock_init, End
B - 953948 - do ddr sanity test, Start
D - 61 - do ddr sanity test, Delta
B - 958615 - Image Load, Start
D - 133102 - QSEE Image Loaded, Delta - (580180 Bytes)
B - 1092601 - Image Load, Start
D - 5704 - DEVCFG Image Loaded, Delta - (13592 Bytes)
B - 1098732 - Image Load, Start
D - 101595 - APPSBL Image Loaded, Delta - (423354 Bytes)
B - 1200388 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 1206854 - SBL1, End
D - 1016443 - SBL1, Delta
S - Flash Throughput, 4761 KB/s (1018373 Bytes, 213857 us)
S - DDR Frequency, 800 MHz
S - Core 0 Frequency, 800 MHz
U-Boot 2016.01 (Dec 01 2022 - 15:50:08 +0800)
ELX version: 1.0.2
DRAM: smem ram ptable found: ver: 1 len: 4
1 GiB
NAND: QPIC controller support serial NAND
ID = 3b7c2
Vendor = c2
Device = b7
Serial Nand Device Found With ID : 0xc2 0xb7
Serial NAND device Manufacturer:MX35UF4GE4AD-Z4I
Device Size:512 MiB, Page size:4096, Spare Size:160, ECC:8-bit
SPI_ADDR_LEN=3
SF: Detected W25Q32DW with page size 256 Bytes, erase size 4 KiB, total 4 MiB
ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x400000
516 MiB
MMC: sdhci: Node Not found, skipping initialization
PCI Link Intialized
In: serial@78AF000
Out: serial@78AF000
Err: serial@78AF000
machid: 8040004
eth0 MAC Address from ART is not valid
eth1 MAC Address from ART is not valid 0
Hit any key to stop autoboot: 0