Here's a Serial Log so that a kind soul takes mercy on us less versed can make heads or tails of support for 1043v5.
U-Boot 1.1.4-g6ce9309a-dirty (Oct 26 2016 - 09:20:53)
ap152 - Dragonfly 1.0
DRAM: 64 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 393k for U-Boot at: 83f9c000
Reserving 16448k for malloc() at: 82f8c000
Reserving 44 Bytes for Board Info at: 82f8bfd4
Reserving 36 Bytes for Global Data at: 82f8bfb0
Reserving 128k for boot params() at: 82f6bfb0
Stack Pointer at: 82f6bf98
Now running in RAM - U-Boot at: 83f9c000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init ::done
Dragonfly ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Setting 0x181162c0 to 0x20402100
factory boot check integer ok.
factory boot load fs uboot len 131072 to addr 0x80010000.
Hit any key to stop autoboot: 0
## Starting application at 0x80010000 ...
U-Boot 1.1.4-g6ce9309a-dirty (Oct 26 2016 - 09:24:21)
ap152 - Dragonfly 1.0
DRAM: 64 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 122k for U-Boot at: 83fe0000
Reserving 16448k for malloc() at: 82fd0000
Reserving 44 Bytes for Board Info at: 82fcffd4
Reserving 36 Bytes for Global Data at: 82fcffb0
Reserving 128k for boot params() at: 82faffb0
Stack Pointer at: 82faff98
Now running in RAM - U-Boot at: 83fe0000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init ::done
Dragonfly ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Setting 0x181162c0 to 0x20402100
Hit any key to stop autoboot: 0
## Booting image at 9f040000 ...
Image Name: MIPS OpenWrt Linux-3.3.8
Created: 2016-10-25 3:58:50 UTC
Image Type: MIPS Linux Multi-File Image (lzma compressed)
Data Size: 1083030 Bytes = 1 MB
Load Address: 80060000
Entry Point: 80060000
Contents:
Image 0: 1083022 Bytes = 1 MB
Verifying Checksum at 0x9f040040 ...OK
Uncompressing Multi-File Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 67108864
Starting kernel ...
[ 0.000000] Linux version 3.3.8 (HQL@localhost.localdomain) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #2 Mon Oct 10 12:11:34 HKT 2016
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019750 (MIPS 74Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA956X rev 0
[ 0.000000] Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,115200 board=AP152 rootfstype=squashfs init=/etc/preinit mtdparts=spi0.0:128k(factory-uboot),128k(u-boot),1152k(uImage),14912k(rootfs),64k@0xff0000(ART) mem=64M rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61260k/65536k available (2316k kernel code, 4276k reserved, 575k data, 180k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:83
[ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 512
[ 0.070000] Initialized recycle list for cpu 0.
[ 0.070000] NET: Registered protocol family 16
[ 0.080000] gpiochip_add: registered GPIOs 0 to 22 on device: ath79
[ 0.080000] MIPS: machine is TP-LINK WR1043N v5 support
[ 0.090000] ar724x-pci ar724x-pci.0: PCIe link is down
[ 0.090000] registering PCI controller with io_map_base unset
[ 0.300000] bio: create slab <bio-0> at 0
[ 0.300000] PCI host bridge to bus 0000:00
[ 0.310000] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[ 0.310000] pci_bus 0000:00: root bus resource [io 0x0001]
[ 0.320000] Switching to clocksource MIPS
[ 0.320000] NET: Registered protocol family 2
[ 0.330000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.330000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.340000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.340000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.350000] TCP reno registered
[ 0.350000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.360000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.360000] NET: Registered protocol family 1
[ 0.380000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.380000] msgmni has been set to 119
[ 0.390000] io scheduler noop registered
[ 0.390000] io scheduler deadline registered (default)
[ 0.400000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.420000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.430000] console [ttyS0] enabled, bootconsole disabled
[ 0.430000] console [ttyS0] enabled, bootconsole disabled
[ 0.440000] m25p80 spi0.0: found w25q128, expected m25p80
[ 0.450000] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.450000] 5 cmdlinepart partitions found on MTD device spi0.0
[ 0.460000] Creating 5 MTD partitions on "spi0.0":
[ 0.460000] 0x000000000000-0x000000020000 : "factory-uboot"
[ 0.470000] 0x000000020000-0x000000040000 : "u-boot"
[ 0.480000] 0x000000040000-0x000000160000 : "uImage"
[ 0.480000] 0x000000160000-0x000000ff0000 : "rootfs"
[ 0.490000] mtd: partition "rootfs" set to be root filesystem
[ 0.500000] 0x000000ff0000-0x000001000000 : "ART"
[ 0.500000] flash_chrdev : flash_chrdev_init
[ 0.640000] ag71xx_mdio: probed
[ 0.650000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 1.230000] eth0: Atheros AR8327 switch driver attached.
[ 4.150000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 4.170000] TCP cubic registered
[ 4.170000] NET: Registered protocol family 17
[ 4.170000] Bridge firewalling registered
[ 4.180000] 8021q: 802.1Q VLAN Support v1.8
[ 4.180000] ### of_selftest(): No testcase data in device tree; not running tests
[ 4.200000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 4.200000] Freeing unused kernel memory: 180k freed
- preinit -
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -
[ 6.460000] liblog: module license 'unspecified' taints kernel.
[ 6.460000] Disabling lock debugging due to kernel taint
[ 6.730000] NET: Registered protocol family 10
[ 6.870000] SCSI subsystem initialized
[ 7.040000] Button Hotplug driver version 0.4.1
[ 7.120000] PPP generic driver version 2.4.2
[ 7.140000] tun: Universal TUN/TAP device driver, 1.6
[ 7.140000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 7.220000] PPP MPPE Compression module registered
[ 7.230000] NET: Registered protocol family 24
[ 7.330000] L2TP core driver, V2.0
[ 7.340000] L2TP netlink interface
[ 7.420000] IPv6 over IPv4 tunneling driver
[ 7.460000] GRE over IPv4 demultiplexor driver
[ 7.500000] GRE over IPv4 tunneling driver
[ 7.550000] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[ 7.670000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.840000] nf_conntrack version 0.5.0 (960 buckets, 3840 max)
[ 8.070000] PPPoL2TP kernel driver, V2.0
[ 8.110000] PPTP driver version 0.8.5
[ 8.470000] xt_time: kernel timezone is -0000
[ 8.840000] nf_conntrack_rtsp v0.6.21 loading
[ 8.850000] nf_nat_rtsp v0.6.21 loading
[ 8.900000] Netfilter messages via NETLINK v0.30.
[ 8.940000] ctnetlink v0.93: registering with nfnetlink.
[ 9.200000] ssdk_plat_init start
[ 9.200000] Register QCA PHY driver
[ 9.320000] qca-ssdk module init succeeded!
[ 9.470000] fuse init (API version 7.18)
reloadconfig() begin:
reloadconfig() end:
mergeconfigbycountry() begin
user has set country
mergeconfigbycountry() do nothing end
reload_profile() begin:
reload_profile() end:
Please press Enter to activate this console. [ 12.190000] ADDRCONF(NETDEV_UP): eth0: link is not ready
GMT+08:00
Fri Jan 1 00:00:00 GMT 2016
[SWITCH DEBUG] Clear Port(0) PVID
[SWITCH DEBUG] Clear Port(1) PVID
[SWITCH DEBUG] Clear Port(2) PVID
[SWITCH DEBUG] Clear Port(3) PVID
[SWITCH DEBUG] Clear Port(4) PVID
[SWITCH DEBUG] Clear Port(5) PVID
[SWITCH DEBUG] Flush vlan entries.
[SWITCH DEBUG] Create VLAN VID=1
[SWITCH DEBUG] Add tagged port(0) to VLAN(1)
[SWITCH DEBUG] Add untagged port(1) to VLAN(1)
[SWITCH DEBUG] Add untagged port(2) to VLAN(1)
[SWITCH DEBUG] Add untagged port(3) to VLAN(1)
[SWITCH DEBUG] Add untagged port(4) to VLAN(1)
[SWITCH DEBUG] Set Port(0) PVID(1)
[SWITCH DEBUG] Set Port(0) ingress to secure
[SWITCH DEBUG] Set Port(1) PVID(1)
[SWITCH DEBUG] Set Port(1) ingress to secure
[SWITCH DEBUG] Set Port(2) PVID(1)
[SWITCH DEBUG] Set Port(2) ingress to secure
[SWITCH DEBUG] Set Port(3) PVID(1)
[SWITCH DEBUG] Set Port(3) ingress to secure
[SWITCH DEBUG] Set Port(4) PVID(1)
[SWITCH DEBUG] Set Port(4) ingress to secure
[SWITCH DEBUG] Create VLAN VID=4094
[SWITCH DEBUG] Add tagged port(0) to VLAN(4094)
[SWITCH DEBUG] Add untagged port(5) to VLAN(4094)
[SWITCH DEBUG] Set Port(0) PVID(4094)
[SWITCH DEBUG] Set Port(0) ingress to secure
[SWITCH DEBUG] Set Port(5) PVID(4094)
[SWITCH DEBUG] Set Port(5) ingress to secure
[SWITCH DEBUG] Set Port(0) PVID(0)
[ 13.860000] device eth0 entered promiscuous mode
[ 13.870000] ADDRCONF(NETDEV_UP): eth0.4094: link is not ready
[ 14.210000] eth0: link up (1000Mbps/Full duplex)
[ 14.230000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 14.230000] ADDRCONF(NETDEV_CHANGE): eth0.4094: link becomes ready
[ 14.310000] ADDRCONF(NETDEV_UP): lo: link is not ready
[ 14.320000] ADDRCONF(NETDEV_UP): ip6tnl0: link is not ready
[ 14.330000] ADDRCONF(NETDEV_UP): sit0: link is not ready
[ 14.330000] ADDRCONF(NETDEV_UP): gre0: link is not ready
[ 14.340000] ADDRCONF(NETDEV_UP): bond0: link is not ready
[ 15.240000] ar8216_read_status_2991: eth0.4094 carrier off!
[ 15.360000] ADDRCONF(NETDEV_UP): eth0.4094: link is not ready
Loading defaults
Loading synflood protection
Adding custom chains
Loading zones
Loading forwardings
Loading rules
Loading redirects
Loading includes
Optimizing conntrack
Loading interfaces
Loading tpcmd
[ 19.670000] device eth0 left promiscuous mode
[ 19.670000] del ct event: 2 dev_name: eth0.4094
[ 19.680000] start clean up ct iterate..
[ 19.690000] device eth0 entered promiscuous mode
[ 19.710000] del ct event: 2 dev_name: eth0.1
[ 19.710000] start clean up ct iterate..
[ 19.730000] device eth0.1 entered promiscuous mode
[ 19.730000] br-lan: port 1(eth0.1) entered forwarding state
[ 19.740000] br-lan: port 1(eth0.1) entered forwarding state
loading access_control
[ 20.460000] ar8216_read_status_2991: eth0.1 carrier off!
[ 20.470000] ar8216_read_status_2991: eth0.4094 carrier off!
[ 20.470000] br-lan: port 1(eth0.1) entered disabled state
loading basic_security
[ 23.990000] start clean up ct iterate..
conntrack v1.0.0 (conntrack-tools): connection tracking table has been emptied.
[ 24.290000] start clean up ct iterate..
[ 30.190000] start clean up ct iterate..
Normal env generate
Flush nat forwarding chain
loading administration management
fw unload_local_mgnt
loading parental_control
SSDK Init OK![ 32.440000] enable:1
[ 32.440000] bg task init successfull!
[ 32.440000] host_helper_init start
[ 32.450000] /proc/qca_switch/nf_athrs17_hnat is created
[ 32.460000] /proc/qca_switch/nf_athrs17_hnat_wan_type is created
[ 32.470000] /proc/qca_switch/nf_athrs17_hnat_ppp_id is created
[ 32.470000] /proc/qca_switch/nf_athrs17_hnat_udp_thresh is created
[ 32.480000] /proc/qca_switch/nf_athrs17_hnat_wan_ip is created
[ 32.480000] /proc/qca_switch/nf_athrs17_hnat_ppp_peer_ip is created
[ 32.490000] /proc/qca_switch/nf_athrs17_hnat_ppp_peer_mac is created
[ 32.500000] /proc/qca_switch/nf_athrs17_hnat_wan_mac is created
[ 32.500000] /proc/qca_switch/nf_athrs17_hnat_ppp_id2 is created
[ 32.510000] /proc/qca_switch/nf_athrs17_hnat_ppp_peer_mac is created
[ 32.520000] Adding ACL rules 15 - upnp_ssdp_add_acl_rules
[ 32.540000] ACL is not yet enabled. Enabling...
[ 32.550000] Adding ACL rules 7 - ipv6_snooping_solicted_node_add_acl_rules
[ 32.600000] Adding ACL rules 11 - ipv6_snooping_sextuple0_group_add_acl_rules
[ 32.650000] Adding ACL rules 13 - ipv6_snooping_quintruple0_1_group_add_acl_rules
[ 32.700000] Hello, nat helper module for 1.1!
[ 32.720000] register inet_notifier###
operate done.
SSDK Init OK![ 32.720000] enable:0
[ 32.730000] unregister inet_notifier###
[ 32.730000] /proc/qca_switch/nf_athrs17_hnat removed
[ 34.710000] Goodbye, nat helper module!
operate done.
[ 39.550000] ****Address of trace_timer :832fe610
[ 40.110000] ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D)
[ 40.220000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
[ 40.350000] ath_dfs: Version 2.0.0
[ 40.350000] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
[ 40.400000] ath_spectral: Version 2.0.0
[ 40.400000] Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reserved
[ 40.410000] SPECTRAL module built on Oct 25 2016 11:22:49
[ 40.550000] ath_tx99: Version 2.0
[ 40.550000] Copyright (c) 2010 Atheros Communications, Inc, All Rights Reserved
[ 40.810000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
[ 43.490000] __ath_attach: Set global_scn[0]
[ 43.490000] *** All the minfree values should be <= ATH_TXBUF-32, otherwise default value will be used instead ***
[ 43.500000] ACBKMinfree = 48
[ 43.500000] ACBEMinfree = 32
[ 43.510000] ACVIMinfree = 16
[ 43.510000] ACVOMinfree = 0
[ 43.510000] CABMinfree = 48
[ 43.520000] UAPSDMinfree = 0
[ 43.520000] ATH_TXBUF=540
[ 43.530000] Enterprise mode: 0x03bda000
[ 43.540000]
[ 43.540000] ART Version : -48.0.0
[ 43.540000] SW Image Version : -48.0.0.0.0
[ 43.550000] Board Revision :
[ 43.550000] ar9300_attach: nf_2_nom -110 nf_2_max -60 nf_2_min -125
[ 43.560000] SPECTRAL : get_capability not registered
[ 43.560000] HAL_CAP_PHYDIAG : Capable
[ 43.570000] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 231)
[ 43.580000] SPECTRAL : get_capability not registered
[ 43.580000] HAL_CAP_RADAR : Capable
[ 43.580000] SPECTRAL : Need to fix the capablity check for SPECTRAL
[ 43.580000] (spectral_attach : 236)
[ 43.590000] SPECTRAL : get_capability not registered
[ 43.600000] HAL_CAP_SPECTRAL_SCAN : Capable
[ 43.600000] SPECTRAL : get_tsf64 not registered
[ 43.610000] spectral_init_netlink 65 NULL SKB
[ 43.610000] SPECTRAL : No ADVANCED SPECTRAL SUPPORT
[ 43.620000] SPECTRAL :----- module attached
[ 43.620000] Green-AP : Green-AP : Attached
[ 43.620000]
[ 43.630000] ath_get_caps[6169] rx chainmask mismatch actual 7 sc_chainmak 0
[ 43.640000] ath_get_caps[6144] tx chainmask mismatch actual 7 sc_chainmak 0
[ 43.650000] band steering initialized for direct attach hardware
[ 43.660000] ieee80211_bsteering_attach: Band steering initialized
[ 43.660000] ath_attach_dfs[12687] dfsdomain 1
[ 43.680000] SPECTRAL : module already attached
[ 43.680000] osif_wrap_attach:296 osif wrap attached
[ 43.690000] osif_wrap_devt_init:916 osif wrap dev table init done
[ 43.700000] ath_tx_paprd_init sc 824e0000 PAPRD disabled in HAL
[ 43.700000] wifi0: Atheros 956X: mem=0xb8100000, irq=47
[ 43.710000] ath_pci: SmartAntenna-DRT-0.1 (Atheros/multi-bss)
[ 44.510000] ath_attach_dfs[12687] dfsdomain 1
[ 44.630000] wlan_vap_create : enter. devhandle=0x82650380, opmode=IEEE80211_M_HOSTAP, flags=0x3
[ 44.640000] wlan_vap_create : exit. devhandle=0x82650380, opmode=IEEE80211_M_HOSTAP, flags=0x3.
[ 44.650000] VAP device ath0 created osifp: (8318b380) os_if: (824f8000)
[ 44.680000] Set freq vap 0 stop send + 824f8000
[ 44.680000] Set freq vap 0 stop send -824f8000
[ 44.820000] Set wait done --824f8000
[ 44.850000] WARNING: Fragmentation with HT mode NOT ALLOWED!!
[ 44.870000] Set freq vap 0 stop send + 824f8000
[ 44.870000] Set freq vap 0 stop send -824f8000
[ 45.010000] Set wait done --824f8000
[ 45.110000]
[ 45.110000] DES SSID SET=
[ 45.120000]
[ 45.120000] DES SSID SET=TP-LINK_1ED0
@@@@@@@@@@psk-mixed/tkip+aes
[ 45.450000] ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
[ 45.460000] DEVICE IS DOWN ifname=ath0
[ 45.470000] DEVICE IS DOWN ifname=ath0
[ 45.740000] device ath0 entered promiscuous mode
[ 45.930000] br-lan: port 2(ath0) entered forwarding state
[ 45.930000] br-lan: port 2(ath0) entered forwarding state
[ 45.950000] 8021q: adding VLAN 0 to HW filter on device ath0
[ 46.650000] fast-classifier: starting up
[ 46.650000] fast-classifier: registered
phyport start .......
SETUP port (5) duplex: 1000 full autoneg: on!
loading qos
http://192.168.0.1/webpages/wan_error.html
192.168.0.1
http://192.168.0.1/webpages/wan_error.html
192.168.0.1
3200 root 1772 S /usr/sbin/crond -c /etc/crontabs -l 5