It runs fine initally, web interface also works.......but after first reboot (even without changing any settings), enters into boot loop, sometimes starts to work again after multiple (auto) boots
Tired many versions, currently using :
openwrt-19.07.3-lantiq-xrx200-bt_homehub-v5a-squashfs-sysupgrade.bin
*******************************************************************************************************************************The Following Repeats again and again
ROM VER: 1.1.4
CFG 06
NAND
NAND Read OK
DDR autotuning Rev 0.3d
DDR size from 0xa0000000 - 0xa7ffffff
DDR check ok... start booting...
U-Boot 2010.06-LANTIQ-v-2.2.46 (Dec 28 2013 - 00:25:33 on bat@gonzo-jungo)
CLOCK CPU 500M RAM 250M
secure boot
DRAM: 125 MiB
NAND: ONFI flash detected
ONFI param page 0 valid
NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD S34ML01G1)
128 MiB
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
In: serial
Out: serial
Err: serial
Net: Internal phy(GE) firmware version: 0x841b
vr9 Switch
Type "run flash_nfs" to mount root filesystem over NFS
Hit any key to stop autoboot: 0
Creating 1 MTD partitions on "nand0":
0x000000100000-0x000007f80000 : "mtd=0"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=0"
UBI: MTD device size: 126 MiB
UBI: number of good PEBs: 1012
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 4
UBI: available PEBs: 10
UBI: total number of reserved PEBs: 1002
UBI: number of PEBs reserved for bad PEB handling: 10
UBI: max/mean erase counter: 140/96
Volume kernel found at volume id 0
read 0 bytes from volume 0 to 80800000(buf address)
Read [2064384] bytes
## Booting kernel from Legacy Image at 80800000 ...
Image Name: MIPS OpenWrt Linux-4.14.180
Created: 2020-05-16 18:32:20 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2007568 Bytes = 1.9 MiB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 4.14.180 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11063-85e04e9f46)) #0 SMP Sat May 16 18:32:20 2020
[ 0.000000] SoC: xRX200 rev 1.2
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[ 0.000000] MIPS: machine is BT Home Hub 5A
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Detected 1 available secondary CPU(s)
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] random: get_random_bytes called from 0x80634740 with crng_init=0
[ 0.000000] percpu: Embedded 14 pages/cpu s25968 r8192 d23184 u57344
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyLTQ0,115200
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00048444
[ 0.000000] Readback ErrCtl register=00048444
[ 0.000000] Memory: 121888K/131072K available (5224K kernel code, 199K rwdata, 912K rodata, 1264K init, 230K bss, 9184K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 500MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
[ 0.000011] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
[ 0.007907] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[ 0.046001] pid_max: default: 32768 minimum: 301
[ 0.050920] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.057435] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.066884] Hierarchical SRCU implementation.
[ 0.072353] smp: Bringing up secondary CPUs ...
[ 0.077806] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.077819] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.077974] CPU1 revision is: 00019556 (MIPS 34Kc)
[ 0.109027] Synchronize counters for CPU 1: done.
[ 0.133343] smp: Brought up 1 node, 2 CPUs
[ 0.142053] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.151719] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.158005] pinctrl core: initialized pinctrl subsystem
[ 0.164832] NET: Registered protocol family 16
[ 0.180297] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.186618] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[ 0.198684] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[ 0.206673] PCI host bridge /fpi@10000000/pci@e105400 ranges:
[ 0.212381] MEM 0x0000000018000000..0x0000000019ffffff
[ 0.217642] IO 0x000000001ae00000..0x000000001affffff
[ 0.342329] PCI host bridge /fpi@10000000/pcie@d900000 ranges:
[ 0.374160] usbcore: registered new interface driver usbfs
[ 0.379804] usbcore: registered new interface driver hub
[ 0.385223] usbcore: registered new device driver usb
[ 0.390937] PCI host bridge to bus 0000:00
[ 0.394970] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[ 0.401893] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff]
[ 0.408816] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.415693] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.424333] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[ 0.431281] PCI host bridge to bus 0000:01
[ 0.435311] pci_bus 0000:01: root bus resource [mem 0x1c000000-0x1cffffff]
[ 0.442229] pci_bus 0000:01: root bus resource [io 0x1d800000-0x1d8fffff]
[ 0.449154] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
[ 0.456028] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.464093] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
[ 0.482330] pci 0000:01:00.0: bridge configuration invalid ([bus 02-00]), reconfiguring
[ 0.491520] pci 0000:01:00.0: BAR 8: assigned [mem 0x1c000000-0x1c1fffff]
[ 0.498236] pci 0000:01:00.0: BAR 9: assigned [mem 0x1c200000-0x1c2fffff pref]
[ 0.505515] pci 0000:02:00.0: BAR 0: assigned [mem 0x1c000000-0x1c1fffff 64bit]
[ 0.512928] pci 0000:02:00.0: BAR 6: assigned [mem 0x1c200000-0x1c20ffff pref]
[ 0.520167] pci 0000:01:00.0: PCI bridge to [bus 02]
[ 0.525198] pci 0000:01:00.0: bridge window [mem 0x1c000000-0x1c1fffff]
[ 0.532069] pci 0000:01:00.0: bridge window [mem 0x1c200000-0x1c2fffff pref]
[ 0.541569] clocksource: Switched to clocksource MIPS
[ 0.549115] NET: Registered protocol family 2
[ 0.554684] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.561605] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.568015] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.574589] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.580385] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.586658] random: fast init done
[ 0.590486] NET: Registered protocol family 1
[ 0.595513] gptu: totally 6 16-bit timers/counters
[ 0.600555] gptu: misc_register on minor 63
[ 0.604704] gptu: succeeded to request irq 126
[ 0.609206] gptu: succeeded to request irq 127
[ 0.613729] gptu: succeeded to request irq 128
[ 0.618230] gptu: succeeded to request irq 129
[ 0.622745] gptu: succeeded to request irq 130
[ 0.627243] gptu: succeeded to request irq 131
[ 0.631942] No VPEs reserved for AP/SP, not initialize VPE loader
[ 0.631942] Pass maxvpes=<n> argument as kernel argument
[ 0.643305] No TCs reserved for AP/SP, not initializing RTLX.
[ 0.643305] Pass maxtcs=<n> argument as kernel argument
[ 0.656086] Crashlog allocated RAM at address 0x3f00000
[ 0.661902] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 0.680759] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.686531] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.703442] io scheduler noop registered
[ 0.707263] io scheduler deadline registered (default)
[ 0.716675] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[ 0.725695] console [ttyLTQ0] enabled
[ 0.725695] console [ttyLTQ0] enabled
[ 0.732928] bootconsole [early0] disabled
[ 0.732928] bootconsole [early0] disabled
[ 0.744895] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
[ 0.749810] nand: AMD/Spansion S34ML01G1
[ 0.753732] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.762049] Bad block table found at page 65472, version 0x01
[ 0.767843] Bad block table found at page 65408, version 0x01
[ 0.773061] 4 fixed-partitions partitions found on MTD device 14000000.nand
[ 0.779783] Creating 4 MTD partitions on "14000000.nand":
[ 0.785203] 0x000000000000-0x0000000a0000 : "u-boot"
[ 0.791795] 0x0000000a0000-0x0000000c0000 : "uboot-env"
[ 0.797243] 0x0000000c0000-0x000000100000 : "unused"
[ 0.802611] 0x000000100000-0x000007f80000 : "ubi"
[ 0.813219] libphy: Fixed MDIO Bus: probed
[ 0.820611] wdt 1f8803f0.watchdog: Init done
[ 0.830315] NET: Registered protocol family 10
[ 0.836865] Segment Routing with IPv6
[ 0.839316] NET: Registered protocol family 17
[ 0.843705] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 0.856546] 8021q: 802.1Q VLAN Support v1.8
[ 0.970960] libphy: lantiq,xrx200-mdio: probed
[ 0.980621] net-xrx200: invalid MAC, using random
[ 1.054181] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 0:00: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6] (mii_bus:phy_addr=0:00, irq=POLL)
[ 1.138160] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 0:01: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6] (mii_bus:phy_addr=0:01, irq=POLL)
[ 1.222147] Intel XWAY PHY11G (xRX v1.2 integrated) 0:11: attached PHY driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (mii_bus:phy_addr=0:11, irq=POLL)
[ 1.306144] Intel XWAY PHY11G (xRX v1.2 integrated) 0:13: attached PHY driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (mii_bus:phy_addr=0:13, irq=POLL)
[ 1.390160] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 0:05: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6] (mii_bus:phy_addr=0:05, irq=POLL)
[ 1.406828] UBI: auto-attach mtd3
[ 1.408721] ubi0: attaching mtd3
[ 1.558082] ubi0: scanning is finished
[ 1.574868] ubi0: attached mtd3 (name "ubi", size 126 MiB)
[ 1.578952] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[ 1.585820] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[ 1.592534] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
[ 1.599324] ubi0: good PEBs: 1012, bad PEBs: 0, corrupted PEBs: 0
[ 1.605398] ubi0: user volume: 4, internal volumes: 1, max. volumes count: 128
[ 1.612632] ubi0: max/mean erase counter: 140/96, WL threshold: 4096, image sequence number: 362341660
[ 1.621956] ubi0: available PEBs: 0, total reserved PEBs: 1012, PEBs reserved for bad PEB handling: 20
[ 1.631341] ubi0: background thread "ubi_bgt0d" started, PID 424
[ 1.636814] block ubiblock0_1: created from ubi0:1(rootfs)
[ 1.642811] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 1.650108] USB_VBUS[ 1.660145] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 1.669858] Freeing unused kernel memory: 1264K
[ 1.672957] This architecture does not have kernel memory protection.
[ 2.300985] init: Console is alive
[ 2.303395] init: - watchdog -
[ 3.654358] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.774072] dwc2 1e101000.usb: 1e101000.usb supply vusb_d not found, using dummy regulator
[ 3.781098] dwc2 1e101000.usb: 1e101000.usb supply vusb_a not found, using dummy regulator
[ 3.789742] dwc2 1e101000.usb: dwc2_core_reset() HANG! AHB Idle GRSTCTL=0
[ 3.997936] dwc2 1e101000.usb: DWC OTG Controller
[ 4.001288] dwc2 1e101000.usb: new USB bus registered, assigned bus number 1
[ 4.008380] dwc2 1e101000.usb: irq 62, io mem 0x1e101000
[ 4.015167] hub 1-0:1.0: USB hub found
[ 4.017723] hub 1-0:1.0: 1 port detected
[ 4.023701] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.032213] init: - preinit -
[ 4.593627] usb 1-1: new high-speed USB device number 2 using dwc2
[ 4.623588] lantiq,xrx200-net 1e108000.eth eth0: port 4 got link
[ 4.945273] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 8.343650] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 497
[ 8.374221] UBIFS (ubi0:2): recovery needed
[ 8.475965] UBIFS (ubi0:2): recovery completed
[ 8.479291] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 8.486841] UBIFS (ubi0:2): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 8.496758] UBIFS (ubi0:2): FS size: 119992320 bytes (114 MiB, 930 LEBs), journal size 6064128 bytes (5 MiB, 47 LEBs)
[ 8.507370] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB)
[ 8.514002] UBIFS (ubi0:2): media format: w4/r0 (latest is w5/r0), UUID 1972F900-AE77-441B-B04D-7DE4D9F32188, small LPT model
[ 8.527308] mount_root: switching to ubifs overlay
[ 8.568868] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 8.816395] procd: - early -
[ 8.818108] procd: - watchdog -
[ 9.245610] lantiq,xrx200-net 1e108000.eth eth0: port 4 lost link
[ 9.498943] procd: - watchdog -
[ 9.501282] procd: - ubus -
[ 9.600760] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.607512] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.613176] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.620794] procd: - init -
Please press Enter to activate this console.
[ 10.937821] kmodloader: loading kernel modules from /etc/modules.d/*
[ 10.946432] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
[ 10.957001] NET: Registered protocol family 8
[ 10.960015] NET: Registered protocol family 20
[ 10.972450] PPP generic driver version 2.4.2
[ 10.988609] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.014775] Lantiq (VRX) DSL CPE MEI driver, version 1.5.17.6, (c) 2007-2015 Lantiq Beteiligungs-GmbH & Co. KG
[ 11.027724]
[ 11.027724]
[ 11.027724] Lantiq CPE API Driver version: DSL CPE API V4.17.18.6
[ 11.045389]
[ 11.045389] Predefined debug level: 3
[ 11.058392] Loading modules backported from Linux version v4.19.120-0-gfdc072324f3c
[ 11.064680] Backport generated by backports.git v4.19.120-1-0-g60c3a249
[ 11.075160] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.084892] Infineon Technologies DEU driver version 2.0.0
[ 11.091682] IFX DEU DES initialized (multiblock).
[ 11.096704] IFX DEU AES initialized (multiblock).
[ 11.100807] IFX DEU ARC4 initialized (multiblock).
[ 11.105176] IFX DEU SHA1 initialized.
[ 11.108874] IFX DEU MD5 initialized.
[ 11.112524] IFX DEU SHA1_HMAC initialized.
[ 11.116530] IFX DEU MD5_HMAC initialized.
[ 11.130824] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 11.195626] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[ 11.207053] owl-loader 0000:00:0e.0: fixup device configuration
[ 11.215386] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[ 11.225229] NET: Registered protocol family 24
[ 11.250049] xt_time: kernel timezone is -0000
[ 11.541284] urngd: v1.0.2 started.
[ 11.596655] ifx_pcie_bios_map_irq port 0 dev 0000:02:00.0 slot 0 pin 1
[ 11.601907] ifx_pcie_bios_map_irq dev 0000:02:00.0 irq 144 assigned
[ 11.608164] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x3c.
[ 11.617944] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[ 11.622439] PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
[ 11.628169] ath10k_pci 0000:02:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 11.868073] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:02:00.0.txt failed with error -2
[ 11.877292] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 11.910607] random: crng init done
[ 11.912560] random: 6 urandom warning(s) missed due to ratelimiting
[ 12.186761] firmware ath10k!fwcfg-pci-0000:02:00.0.txt: firmware_loading_store: map pages failed
[ 12.194816] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[ 12.204929] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 12.594349] firmware ath10k!pre-cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[ 12.603850] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/ct-firmware-5.bin failed with error -2
[ 12.613569] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 13.003965] firmware ath10k!QCA988X!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[ 13.012425] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/ct-firmware-2.bin failed with error -2
[ 13.022870] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 13.413008] firmware ath10k!QCA988X!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[ 13.421435] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
[ 13.431613] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 13.821906] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 13.830072] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-5.bin failed with error -2
[ 13.840248] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 14.228451] firmware ath10k!QCA988X!hw2.0!firmware-5.bin: firmware_loading_store: map pages failed
[ 14.236679] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-4.bin failed with error -2
[ 14.246810] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 14.528662] firmware ath10k!QCA988X!hw2.0!firmware-4.bin: firmware_loading_store: map pages failed
[ 14.536740] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-3.bin failed with error -2
[ 14.546975] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 14.831168] firmware ath10k!QCA988X!hw2.0!firmware-3.bin: firmware_loading_store: map pages failed
[ 14.844119] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 14.852106] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 14.868886] ath10k_pci 0000:02:00.0: firmware ver 10.1-ct-8x-__fW-022-b0e1b7cd api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT crc32 1e527180
[ 14.921392] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[ 14.930524] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 15.172807] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[ 15.181024] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 16.062848] ath10k_pci 0000:02:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256
[ 16.078809] ath10k_pci 0000:02:00.0: wmi print 'P 128 V 8 T 410'
[ 16.083441] ath10k_pci 0000:02:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0'
[ 16.091826] ath10k_pci 0000:02:00.0: wmi print 'alloc rem: 20904 iram: 26056'
[ 16.159636] ath10k_pci 0000:02:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[ 16.171170] ath10k_pci 0000:02:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
[ 16.325096] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[ 16.336299] ath: phy1: Ignoring endianness difference in EEPROM magic bytes.
[ 16.369627] ieee80211 phy1: Atheros AR9287 Rev:2 mem=0xb8000000, irq=30
[ 16.376021] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 82.170808] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 82.189342] device eth0 entered promiscuous mode
[ 82.194619] br-lan: port 1(eth0.1) entered blocking state
[ 82.198771] br-lan: port 1(eth0.1) entered disabled state
[ 82.204855] device eth0.1 entered promiscuous mode
[ 82.227441] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 85.369423] lantiq,xrx200-net 1e108000.eth eth0: port 4 got link
[ 85.374513] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 85.381426] br-lan: port 1(eth0.1) entered blocking state
[ 85.385781] br-lan: port 1(eth0.1) entered forwarding state
[ 85.392661] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
... tried almost everything....read hundreds of pages...spent around 24 hours continuous (excluding sleep 
)