RPCError with Archer C7v2 and OpenWrt 24.10.0rc2

[uweklatt]

After updateing the device to version 24.10.0rc2 I got the following error:

Also with a reset configuration...
Is this a known issue?
I have created the sysupgrade image with the firmware builder (without errors).
Uwe

[brada4]

Clear site cache or try in private mode?

[uweklatt]

It has nothing to do with browser cache.
Uwe

[brada4]

In which part of menu you are getting it? (im not getting it on 23.5 upgrade and clean install)

[uweklatt]

I can log in and can open some luci pages.
The error shows up on every page.
There are also other errors:

RPCError
RPC call to luci/getTimezones failed with error -32000: Object not found
  at handleCallReply (http://192.168.1.1/luci-static/resources/rpc.js?v=24.354.67497~bd36a83:11:3)

Not working pages are: Status/Processes, System/System, System/Software, System/LED Configuration, Network/Switch, Network/Firewall

[brada4]

ubus call system board

?

[uweklatt]

@brada4

ubus call system board

root@OpenWrt:~# ubus call system board
{
        "kernel": "6.6.63",
        "hostname": "OpenWrt",
        "system": "Qualcomm Atheros QCA9558 ver 1 rev 0",
        "model": "TP-Link Archer C7 v2",
        "board_name": "tplink,archer-c7-v2",
        "rootfs_type": "squashfs",
        "release": {
                "distribution": "OpenWrt",
                "version": "24.10.0-rc2",
                "revision": "r28161-ea17e958b9",
                "target": "ath79/generic",
                "description": "OpenWrt 24.10.0-rc2 r28161-ea17e958b9",
                "builddate": "1733226068"
        }
}

[uweklatt]

I came from version 22.03, upgraded to 23.05 with no errors.
After upgrade to 24.10 I have this errors.

[brada4]

Backup and flash again with default sysupgrade image clearing configuration. C7V5 - absolutely no problem whatsoever across upgrade with existing quite creative configuration.

[uweklatt]

I installed standard sysupgrade image from image builder and cleared config. - This seems to work!

With my config it doesn't...
Now I must find the reason
Thank you @brada4 for your help
Uwe

[brada4]

Re-type config from unzipped backup file and you are all set.

[uweklatt]

I made a "backup" and was able to install it without problems.
I added my addtional packages now manually.
The question is, why it's not working when I integrate them in the imagebuilder image.

The only difference are the following packages:

- wpad-basic-mbedtls
+ wpad-mesh-mbedtls
+ luci-proto-wireguard
+ openssh-sftp-server

Could this be a problem with imagebuilder?

This is my imagebuilder config:

base-files busybox ca-bundle dnsmasq dropbear firewall4 fstools kmod-ath9k kmod-gpio-button-hotplug kmod-nft-offload libc libgcc libustream-mbedtls logd mtd netifd nftables odhcp6c odhcpd-ipv6only opkg ppp ppp-mod-pppoe procd procd-seccomp procd-ujail swconfig uboot-envtools uci uclient-fetch urandom-seed urngd wpad-mesh-mbedtls kmod-usb2 kmod-usb-ledtrig-usbport kmod-ath10k-ct ath10k-firmware-qca988x-ct luci luci-proto-wireguard openssh-sftp-server

Uwe

[brada4]

It will get fixed in next build.....

RPCError