### Describe the bug
On kernel 6.1, the lan0 interface (PoE-PD port and uplink)… fails to register and is not linked to eth0, rendering the device inaccessible. Error seen over serial:
```
[ 8.974464] mtk_soc_eth 1e100000.ethernet lan0: validation of with support 00000000,00000000,00006000 and advertisement 00000000,00000000,00000000 failed: -EINVAL
[ 9.003873] mtk_soc_eth 1e100000.ethernet lan0: mtk_open: could not attach PHY: -22
ip: SIOCSIFFLAGS: Invalid argument
```
Full boot log linked below.
Ip will show lan0 as detached from eth0:
```
# ip a s
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1504 qdisc mq state UP qlen 1000
link/ether a4:2b:b0:2e:e9:88 brd ff:ff:ff:ff:ff:ff
inet6 fe80::a62b:b0ff:fe2e:e988/64 scope link
valid_lft forever preferred_lft forever
3: lan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop master br-lan state DOWN qlen 1000
link/ether a4:2b:b0:2e:e9:88 brd ff:ff:ff:ff:ff:ff
4: lan3@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue master br-lan state LOWERLAYERDOWN qlen 1000
link/ether a4:2b:b0:2e:e9:88 brd ff:ff:ff:ff:ff:ff
5: lan2@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue master br-lan state LOWERLAYERDOWN qlen 1000
link/ether a4:2b:b0:2e:e9:88 brd ff:ff:ff:ff:ff:ff
6: lan1@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue master br-lan state LOWERLAYERDOWN qlen 1000
link/ether a4:2b:b0:2e:e9:88 brd ff:ff:ff:ff:ff:ff
7: br-lan: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN qlen 1000
link/ether a4:2b:b0:2e:e9:88 brd ff:ff:ff:ff:ff:ff
8: br-lan.1@br-lan: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state LOWERLAYERDOWN qlen 1000
link/ether a4:2b:b0:2e:e9:88 brd ff:ff:ff:ff:ff:ff
inet 10.0.0.3/24 brd 10.0.0.255 scope global br-lan.1
valid_lft forever preferred_lft forever
```
### OpenWrt version
r25115+29-7181eb9f81
### OpenWrt release
SNAPSHOT
### OpenWrt target/subtarget
ramips/mt7621
### Device
TP-Link EAP235-Wall v1
### Image kind
Self-built image
### Steps to reproduce
Check out main tree, compile for EAP235-Wall with testing kernel, flash to device (or boot from TFTP).
### Actual behaviour
Lan0 is not registered correctly, making the PoE-PD uplink port inaccessibile.
### Expected behaviour
Lan0 correctly registered and linked to eth0 as on kernel 5.15.
### Additional info
<details>
<summary>Boot log</summary>
```
===================================================================
MT7621 stage1 code Jul 31 2019 14:37:26 (ASIC)
CPU=500000000 HZ BUS=166666666 HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x11100000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-1200Mhz ===
PLL3 FB_DL: 0x8, 1/0 = 695/329 21000000
PLL4 FB_DL: 0x17, 1/0 = 550/474 5D000000
PLL2 FB_DL: 0x19, 1/0 = 616/408 65000000
do DDR setting..[01F40000]
Apply DDR3 Setting...(use customer AC)
0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120
--------------------------------------------------------------------------------
0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1
000E:| 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
000F:| 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0
0010:| 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
0011:| 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0
0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
DRAMC_DQSCTL1[0e0]=13000000
DRAMC_DQSGCTL[124]=80000033
rank 0 coarse = 15
rank 0 fine = 64
B:| 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 0
opt_dle value:8
DRAMC_DDR2CTL[07c]=C287220D
DRAMC_PADCTL4[0e4]=000022B3
DRAMC_DQIDLY1[210]=0D0F0B0E
DRAMC_DQIDLY2[214]=0B0F0A0C
DRAMC_DQIDLY3[218]=0C0B0A0A
DRAMC_DQIDLY4[21c]=0A0B0C0A
DRAMC_R0DELDLY[018]=00002120
==================================================================
RX DQS perbit delay software calibration
==================================================================
1.0-15 bit dq delay value
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 13 10 13 11 12 9 15 11 9 9
10 | 11 10 9 10 10 7
--------------------------------------
==================================================================
2.dqs window
x=pass dqs delay value (min~max)center
y=0-7bit DQ of every group
input delay:DQS0 =32 DQS1 = 33
==================================================================
bit DQS0 bit DQS1
0 (0~62)31 8 (1~63)32
1 (1~62)31 9 (1~63)32
2 (1~60)30 10 (2~64)33
3 (1~60)30 11 (0~63)31
4 (1~64)32 12 (1~63)32
5 (1~61)31 13 (1~62)31
6 (1~62)31 14 (1~64)32
7 (1~64)32 15 (1~59)30
==================================================================
3.dq delay value last
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 14 11 15 13 12 10 15 11 10 10
10 | 11 12 10 12 11 10
==================================================================
==================================================================
TX perbyte calibration
==================================================================
DQS loop = 15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1
dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2
DQ loop=15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=15, finish count=1
dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=2
byte:0, (DQS,DQ)=(8,8)
byte:1, (DQS,DQ)=(8,8)
DRAMC_DQODLY1[200]=88888888
DRAMC_DQODLY2[204]=88888888
20,data:88
[EMI] DRAMC calibration passed
===================================================================
MT7621 stage1 code done
CPU=500000000 HZ BUS=166666666 HZ
===================================================================
U-Boot 1.1.3 (Sep 23 2019 - 18:01:43)
Board: Ralink APSoC DRAM: 128 MB
relocate_code Pointer at: 87fa4000
gpioMode Reg: 0x4d42c
Config XHCI 40M PLL
flash manufacture id: ef, device id 40 18
find flash: W25Q128BV
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: SPI Flash
Date:Sep 23 2019 Time:18:01:43
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =128 Mbytes
-->have merged switch patch from mtk to fix inital error issue!
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load the whole FLASH image then write to Flash(Skip U-Boot & cal-data) via TFTP.
6: Load the whole FLASH image then write to Flash(do NOT skip U-Boot & cal-data) via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3
0
3: System Boot system code via Flash.
## Booting image at bfca0000 ...
text base: 80001000
entry point: 80001000
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 128
Starting kernel ...
[ 0.000000] Linux version 6.1.77 (5800X@crunchbot) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r24624+30-957a0921e2) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Sat Feb 10 14:00:51 2024
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is TP-Link EAP235-Wall v1
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] percpu: Embedded 11 pages/cpu s14944 r8192 d21920 u45056
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=00008103
[ 0.000000] Readback ErrCtl register=00008103
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 119112K/131072K available (7434K kernel code, 633K rwdata, 916K rodata, 1244K init, 220K bss, 11960K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000004] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.015995] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.088301] pid_max: default: 32768 minimum: 301
[ 0.098322] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.112730] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.131273] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.145579] cblist_init_generic: Setting shift to 2 and lim to 1.
[ 0.158127] rcu: Hierarchical SRCU implementation.
[ 0.167499] rcu: Max phase no-delay instances is 1000.
[ 0.178661] smp: Bringing up secondary CPUs ...
[ 0.188447] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.188471] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.188486] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.188534] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.248155] Synchronize counters for CPU 1: done.
[ 0.309818] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.309838] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.309851] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.309879] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.369056] Synchronize counters for CPU 2: done.
[ 0.429455] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.429476] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.429489] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.429523] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.488636] Synchronize counters for CPU 3: done.
[ 0.548227] smp: Brought up 1 node, 4 CPUs
[ 0.561358] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.580850] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.594726] pinctrl core: initialized pinctrl subsystem
[ 0.606447] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.618829] thermal_sys: Registered thermal governor 'step_wise'
[ 0.647564] clocksource: Switched to clocksource GIC
[ 0.658755] NET: Registered PF_INET protocol family
[ 0.668566] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.683633] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.700164] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.715521] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.730740] TCP bind hash table entries: 1024 (order: 2, 16384 bytes, linear)
[ 0.744951] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.757710] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.770617] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.784785] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.796023] PCI: CLS 0 bytes, default 32
[ 0.806934] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.825104] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.836621] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.860635] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.872039] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.883375] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.894884] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 0.908139] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 0.925601] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0060000000
[ 0.941828] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 1.317557] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 1.331332] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 1.340980] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 1.350674] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 1.364805] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 1.377337] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.388212] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.401855] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.414169] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 1.426060] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.438498] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.450999] pci 0000:00:00.0: supports D1
[ 1.458879] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.470877] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 1.482785] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.495175] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.507699] pci 0000:00:01.0: supports D1
[ 1.515536] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 1.528787] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.544632] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.560824] pci 0000:01:00.0: [14c3:7603] type 00 class 0x028000
[ 1.572710] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[ 1.585280] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 1.597610] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.607905] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.619983] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.633470] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref]
[ 1.647806] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.661245] pci 0000:02:00.0: [14c3:7663] type 00 class 0x000280
[ 1.673126] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[ 1.687440] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
[ 1.701781] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
[ 1.716222] pci 0000:02:00.0: supports D1 D2
[ 1.724580] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.737747] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.767578] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 1.777871] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 1.789950] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.803435] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff pref]
[ 1.817781] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 1.830946] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 1.844034] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.857860] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 1.870991] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.884826] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.898296] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[ 1.912639] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[ 1.926122] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x604fffff pref]
[ 1.940466] pci 0000:00:00.0: BAR 1: assigned [mem 0x60500000-0x6050ffff]
[ 1.953943] pci 0000:00:01.0: BAR 1: assigned [mem 0x60510000-0x6051ffff]
[ 1.967419] pci 0000:00:00.0: BAR 7: assigned [io 0x0000-0x0fff]
[ 1.979511] pci 0000:00:01.0: BAR 7: assigned [io 0x1000-0x1fff]
[ 1.991615] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
[ 2.005097] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.014936] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 2.027032] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 2.040513] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref]
[ 2.054860] pci 0000:02:00.0: BAR 0: assigned [mem 0x60300000-0x603fffff 64bit pref]
[ 2.070250] pci 0000:02:00.0: BAR 2: assigned [mem 0x60400000-0x60403fff 64bit pref]
[ 2.085623] pci 0000:02:00.0: BAR 4: assigned [mem 0x60404000-0x60404fff 64bit pref]
[ 2.100999] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 2.110839] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff]
[ 2.122935] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
[ 2.136420] pci 0000:00:01.0: bridge window [mem 0x60300000-0x604fffff pref]
[ 2.152567] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 2.166910] printk: console [ttyS0] disabled
[ 2.175434] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 18, base_baud = 3125000) is a 16550A
[ 2.193363] printk: console [ttyS0] enabled
[ 2.193363] printk: console [ttyS0] enabled
[ 2.209926] printk: bootconsole [early0] disabled
[ 2.209926] printk: bootconsole [early0] disabled
[ 2.232168] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 2.244399] spi-nor spi0.0: w25q128 (16384 Kbytes)
[ 2.254135] 8 fixed-partitions partitions found on MTD device spi0.0
[ 2.266832] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[ 2.281446] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[ 2.296371] Creating 8 MTD partitions on "spi0.0":
[ 2.305946] 0x000000000000-0x000000080000 : "u-boot"
[ 2.317191] 0x000000080000-0x000000090000 : "partition-table"
[ 2.329766] 0x000000090000-0x0000000a0000 : "product-info"
[ 2.341857] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[ 2.356794] 0x0000000a0000-0x000000dc0000 : "firmware"
[ 2.368536] 2 tplink-fw partitions found on MTD device firmware
[ 2.380365] Creating 2 MTD partitions on "firmware":
[ 2.390257] 0x000000000000-0x0000002b8a8b : "kernel"
[ 2.400150] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only
[ 2.417789] 0x0000002b8a8b-0x000000d20000 : "rootfs"
[ 2.427776] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only
[ 2.447132] mtd: setting mtd5 (rootfs) as root device
[ 2.457315] 1 squashfs-split partitions found on MTD device rootfs
[ 2.469631] 0x000000b50000-0x000000d20000 : "rootfs_data"
[ 2.481498] 0x000000dc0000-0x000000df0000 : "user-config"
[ 2.493507] 0x000000f30000-0x000000fb0000 : "mutil-log"
[ 2.505083] 0x000000fb0000-0x000000ff0000 : "oops"
[ 2.515832] 0x000000ff0000-0x000001000000 : "radio"
[ 2.526662] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[ 2.680600] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 2.703675] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 19
[ 2.723811] mtk_soc_eth 1e100000.ethernet lan0: mediatek frame engine at 0xbe100000, irq 19
[ 2.742220] i2c_dev: i2c /dev entries driver
[ 2.753440] NET: Registered PF_INET6 protocol family
[ 2.765897] Segment Routing with IPv6
[ 2.773331] In-situ OAM (IOAM) with IPv6
[ 2.781276] NET: Registered PF_PACKET protocol family
[ 2.791783] 8021q: 802.1Q VLAN Support v1.8
[ 2.809347] gpio-export gpio-export: 1 gpio(s) exported
[ 2.820191] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 2.930527] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode
[ 2.945175] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 2.948749] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=22)
[ 2.983422] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=23)
[ 3.006393] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=24)
[ 3.029443] device eth0 entered promiscuous mode
[ 3.038817] DSA: tree 0 setup
[ 3.053896] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 3.072230] Freeing unused kernel image (initmem) memory: 1244K
[ 3.084096] This architecture does not have kernel memory protection.
[ 3.096942] Run /sbin/init as init process
[ 3.707763] init: Console is alive
[ 3.714935] init: - watchdog -
[ 4.918958] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.000960] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.025875] init: - preinit -
[ 8.537544] random: crng init done
[ 8.974464] mtk_soc_eth 1e100000.ethernet lan0: validation of with support 00000000,00000000,00006000 and advertisement 00000000,00000000,00000000 failed: -EINVAL
[ 9.003873] mtk_soc_eth 1e100000.ethernet lan0: mtk_open: could not attach PHY: -22
ip: SIOCSIFFLAGS: Invalid argument
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
sendto(): Network unreachable
sendto(): Network unreachable
[ 11.306675] jffs2: notice: (444) jffs2_build_xattr_subsystem: complete building xattr subsystem, 23 of xdatum (11 unchecked, 10 orphan) and 25 of xref (10 dead, 0 orphan) found.
[ 11.340180] mount_root: switching to jffs2 overlay
[ 11.356166] overlayfs: upper fs does not support tmpfile.
[ 11.377431] urandom-seed: Seeding with /etc/urandom.seed
[ 11.515557] procd: - early -
[ 11.521641] procd: - watchdog -
[ 12.155630] procd: - watchdog -
[ 12.163290] procd: - ubus -
[ 12.310751] procd: - init -
Please press Enter to activate this console.
[ 13.358887] kmodloader: loading kernel modules from /etc/modules.d/*
[ 13.398333] mtk-eip93 1e004000.crypto: EIP93 Crypto Engine Initialized.
[ 13.653575] cryptodev: driver 1.12 loaded.
[ 13.664007] GACT probability on
[ 13.671828] Mirror/redirect action on
[ 13.689031] u32 classifier
[ 13.694442] input device check on
[ 13.701735] Actions configured
[ 13.734223] Loading modules backported from Linux version v6.5-0-g2dde18cd1d8f
[ 13.748648] Backport generated by backports.git v5.15.92-1-56-g5fb2ccb6b9e8
[ 13.831644] xt_time: kernel timezone is -0000
[ 14.069499] pci 0000:00:00.0: enabling device (0000 -> 0003)
[ 14.080843] mt7603e 0000:01:00.0: enabling device (0000 -> 0002)
[ 14.093007] mt7603e 0000:01:00.0: ASIC revision: 76030010
[ 14.297956] urngd: v1.0.2 started.
[ 15.120998] mt7603e 0000:01:00.0: Firmware Version: ap_pcie
[ 15.132282] mt7603e 0000:01:00.0: Build Time: 20160107100755
[ 15.164919] mt7603e 0000:01:00.0: firmware init done
[ 15.354191] mt7603e 0000:01:00.0: registering led 'mt76-phy0'
[ 15.376649] pci 0000:00:01.0: enabling device (0000 -> 0003)
[ 15.387984] mt7615e 0000:02:00.0: enabling device (0000 -> 0002)
[ 15.416279] mt7615e 0000:02:00.0: registering led 'mt76-phy1'
[ 15.462378] PPP generic driver version 2.4.2
[ 15.472971] NET: Registered PF_PPPOX protocol family
[ 15.491220] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 17.480585] mt7615e 0000:02:00.0: mediatek/mt7663pr2h.bin not found, switching to mediatek/mt7663pr2h_rebb.bin
[ 17.649922] mt7615e 0000:02:00.0: HW/SW Version: 0x65322d31, Build Time: 2009041715da1a1
[ 17.649922]
[ 17.865528] mt7615e 0000:02:00.0: N9 Firmware Version: 7663mp1827, Build Time: 20200904171623
[ 17.882659] mt7615e 0000:02:00.0: Region number: 0x3
[ 17.892628] mt7615e 0000:02:00.0: Parsing tailer Region: 0
[ 17.906734] mt7615e 0000:02:00.0: Region 0, override_addr = 0x00112c00
[ 17.920035] mt7615e 0000:02:00.0: Parsing tailer Region: 1
[ 17.931845] mt7615e 0000:02:00.0: Parsing tailer Region: 2
[ 17.943362] mt7615e 0000:02:00.0: override_addr = 0x00112c00, option = 3
[ 23.519505] mtk_soc_eth 1e100000.ethernet lan0: validation of with support 00000000,00000000,00006000 and advertisement 00000000,00000000,00000000 failed: -EINVAL
[ 23.549113] mtk_soc_eth 1e100000.ethernet lan0: mtk_open: could not attach PHY: -22
[ 23.566308] br-lan: port 1(lan0) entered blocking state
[ 23.576978] br-lan: port 1(lan0) entered disabled state
[ 23.588126] device lan0 entered promiscuous mode
[ 23.642734] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 23.663702] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 23.685679] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 23.701177] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 23.715153] br-lan: port 2(lan1) entered blocking state
[ 23.725863] br-lan: port 2(lan1) entered disabled state
[ 23.742350] device lan1 entered promiscuous mode
[ 23.771336] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 23.787684] br-lan: port 3(lan2) entered blocking state
[ 23.798328] br-lan: port 3(lan2) entered disabled state
[ 23.811955] device lan2 entered promiscuous mode
[ 23.839392] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 23.855305] br-lan: port 4(lan3) entered blocking state
[ 23.865982] br-lan: port 4(lan3) entered disabled state
[ 23.879611] device lan3 entered promiscuous mode
BusyBox v1.36.1 (2024-02-10 14:00:51 UTC) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r25115+29-7181eb9f81
-----------------------------------------------------
Hardware: TP-Link EAP235-Wall v1
root@EAP235-ikkai:/# ip a s
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1504 qdisc mq state UP qlen 1000
link/ether a4:2b:b0:2e:e9:88 brd ff:ff:ff:ff:ff:ff
inet6 fe80::a62b:b0ff:fe2e:e988/64 scope link
valid_lft forever preferred_lft forever
3: lan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop master br-lan state DOWN qlen 1000
link/ether a4:2b:b0:2e:e9:88 brd ff:ff:ff:ff:ff:ff
4: lan3@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue master br-lan state LOWERLAYERDOWN qlen 1000
link/ether a4:2b:b0:2e:e9:88 brd ff:ff:ff:ff:ff:ff
5: lan2@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue master br-lan state LOWERLAYERDOWN qlen 1000
link/ether a4:2b:b0:2e:e9:88 brd ff:ff:ff:ff:ff:ff
6: lan1@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue master br-lan state LOWERLAYERDOWN qlen 1000
link/ether a4:2b:b0:2e:e9:88 brd ff:ff:ff:ff:ff:ff
7: br-lan: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN qlen 1000
link/ether a4:2b:b0:2e:e9:88 brd ff:ff:ff:ff:ff:ff
8: br-lan.1@br-lan: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state LOWERLAYERDOWN qlen 1000
link/ether a4:2b:b0:2e:e9:88 brd ff:ff:ff:ff:ff:ff
inet 10.0.0.3/24 brd 10.0.0.255 scope global br-lan.1
valid_lft forever preferred_lft forever
root@EAP235-ikkai:/#
```
</details>
### Diffconfig
```text
CONFIG_TARGET_ramips=y
CONFIG_TARGET_ramips_mt7621=y
CONFIG_TARGET_MULTI_PROFILE=y
CONFIG_TARGET_DEVICE_ramips_mt7621_DEVICE_asus_rt-ac57u-v1=y
CONFIG_TARGET_DEVICE_PACKAGES_ramips_mt7621_DEVICE_asus_rt-ac57u-v1="kmod-mt76 kmod-usb-net-rndis luci-app-unbound unbound-anchor unbound-control luci-proto-wireguard -wpad-basic-mbedtls -libustream-mbedtls -libmbedtls"
CONFIG_TARGET_DEVICE_ramips_mt7621_DEVICE_dlink_dir-860l-b1=y
CONFIG_TARGET_DEVICE_PACKAGES_ramips_mt7621_DEVICE_dlink_dir-860l-b1="kmod-mt76 kmod-usb-net-rndis luci-app-unbound unbound-anchor unbound-control luci-proto-wireguard -wpad-basic-mbedtls -libustream-mbedtls -libmbedtls"
CONFIG_TARGET_DEVICE_ramips_mt7621_DEVICE_dlink_dir-878-a1=y
CONFIG_TARGET_DEVICE_PACKAGES_ramips_mt7621_DEVICE_dlink_dir-878-a1="kmod-mt7615e kmod-mt7615-firmware luci-app-unbound unbound-anchor unbound-control luci-proto-wireguard -wpad-basic-mbedtls -libustream-mbedtls -libmbedtls"
CONFIG_TARGET_DEVICE_ramips_mt7621_DEVICE_netgear_r6800=y
CONFIG_TARGET_DEVICE_PACKAGES_ramips_mt7621_DEVICE_netgear_r6800="kmod-mt7615e kmod-mt7615-firmware kmod-usb-net-rndis luci-app-unbound unbound-anchor unbound-control luci-proto-wireguard -wpad-basic-mbedtls -libustream-mbedtls -libmbedtls"
CONFIG_TARGET_DEVICE_ramips_mt7621_DEVICE_netgear_wax202=y
CONFIG_TARGET_DEVICE_PACKAGES_ramips_mt7621_DEVICE_netgear_wax202="kmod-mt7915e luci-app-unbound unbound-anchor unbound-control luci-proto-wireguard -wpad-basic-mbedtls -libustream-mbedtls -libmbedtls"
CONFIG_TARGET_DEVICE_ramips_mt7621_DEVICE_tplink_eap235-wall-v1=y
CONFIG_TARGET_DEVICE_PACKAGES_ramips_mt7621_DEVICE_tplink_eap235-wall-v1="kmod-mt7615e kmod-mt7663-firmware-ap -luci-app-ddns -ddns-scripts -odhcpd -wpad-basic-mbedtls -libustream-mbedtls -libmbedtls"
CONFIG_TARGET_DEVICE_ramips_mt7621_DEVICE_tplink_eap615-wall-v1=y
CONFIG_TARGET_DEVICE_PACKAGES_ramips_mt7621_DEVICE_tplink_eap615-wall-v1="kmod-mt7915e -luci-app-ddns -ddns-scripts -odhcpd -wpad-basic-mbedtls -libustream-mbedtls -libmbedtls"
CONFIG_DEVEL=y
CONFIG_TARGET_PER_DEVICE_ROOTFS=y
CONFIG_DROPBEAR_ECC=y
CONFIG_DROPBEAR_ECC_FULL=y
CONFIG_DROPBEAR_ECDSA_SK=y
CONFIG_IMAGEOPT=y
CONFIG_INCLUDE_CONFIG=y
CONFIG_KERNEL_BUILD_DOMAIN="crunchbot"
CONFIG_KERNEL_BUILD_USER="5800X"
CONFIG_KERNEL_CGROUP_NET_PRIO=y
# CONFIG_KERNEL_KALLSYMS is not set
CONFIG_LIBCURL_COOKIES=y
CONFIG_LIBCURL_FILE=y
CONFIG_LIBCURL_HTTP=y
CONFIG_LIBCURL_NGHTTP2=y
CONFIG_LIBCURL_NO_SMB="!"
CONFIG_LIBCURL_OPENSSL=y
CONFIG_LIBCURL_PROXY=y
CONFIG_LIBCURL_UNIX_SOCKETS=y
CONFIG_LINUX_6_1=y
CONFIG_LUCI_SRCDIET=y
# CONFIG_MBEDTLS_ECP_DP_SECP521R1_ENABLED is not set
CONFIG_OPENSSL_ENGINE=y
CONFIG_OPENSSL_OPTIMIZE_SPEED=y
CONFIG_OPENSSL_PREFER_CHACHA_OVER_GCM=y
CONFIG_OPENSSL_WITH_ASM=y
CONFIG_OPENSSL_WITH_CHACHA_POLY1305=y
CONFIG_OPENSSL_WITH_CMS=y
CONFIG_OPENSSL_WITH_DEPRECATED=y
CONFIG_OPENSSL_WITH_ERROR_MESSAGES=y
CONFIG_OPENSSL_WITH_IDEA=y
CONFIG_OPENSSL_WITH_MDC2=y
CONFIG_OPENSSL_WITH_NPN=y
CONFIG_OPENSSL_WITH_PSK=y
CONFIG_OPENSSL_WITH_SEED=y
CONFIG_OPENSSL_WITH_SRP=y
CONFIG_OPENSSL_WITH_TLS13=y
CONFIG_OPENSSL_WITH_WHIRLPOOL=y
CONFIG_PACKAGE_adblock=m
CONFIG_PACKAGE_arp-scan=y
CONFIG_PACKAGE_attendedsysupgrade-common=m
CONFIG_PACKAGE_bridge=y
CONFIG_PACKAGE_cgi-io=y
CONFIG_PACKAGE_collectd=y
CONFIG_PACKAGE_collectd-mod-cpu=y
CONFIG_PACKAGE_collectd-mod-dhcpleases=y
CONFIG_PACKAGE_collectd-mod-dns=y
CONFIG_PACKAGE_collectd-mod-interface=y
CONFIG_PACKAGE_collectd-mod-iwinfo=y
CONFIG_PACKAGE_collectd-mod-load=y
CONFIG_PACKAGE_collectd-mod-logfile=y
CONFIG_PACKAGE_collectd-mod-memory=y
CONFIG_PACKAGE_collectd-mod-network=y
CONFIG_PACKAGE_collectd-mod-rrdtool=y
CONFIG_PACKAGE_collectd-mod-thermal=y
CONFIG_PACKAGE_coreutils=m
CONFIG_PACKAGE_coreutils-sort=m
CONFIG_PACKAGE_curl=y
CONFIG_PACKAGE_dawn=y
CONFIG_PACKAGE_ddns-scripts=y
CONFIG_PACKAGE_ddns-scripts-services=y
CONFIG_PACKAGE_dmesg=y
CONFIG_PACKAGE_dnsmasq=m
CONFIG_PACKAGE_etherwake=m
CONFIG_PACKAGE_ethtool=y
CONFIG_PACKAGE_hostapd-utils=m
CONFIG_PACKAGE_htop=y
CONFIG_PACKAGE_ip-bridge=y
CONFIG_PACKAGE_iperf3=m
CONFIG_PACKAGE_ipset=y
CONFIG_PACKAGE_ipset-dns=y
CONFIG_PACKAGE_iptables-mod-ipopt=y
CONFIG_PACKAGE_iptables-nft=y
CONFIG_PACKAGE_irqbalance=y
CONFIG_PACKAGE_iw=y
CONFIG_PACKAGE_kmod-bonding=m
CONFIG_PACKAGE_kmod-cfg80211=y
CONFIG_PACKAGE_kmod-crypto-ccm=y
CONFIG_PACKAGE_kmod-crypto-cmac=y
CONFIG_PACKAGE_kmod-crypto-ctr=y
CONFIG_PACKAGE_kmod-crypto-gcm=y
CONFIG_PACKAGE_kmod-crypto-gf128=y
CONFIG_PACKAGE_kmod-crypto-ghash=y
CONFIG_PACKAGE_kmod-crypto-hmac=y
CONFIG_PACKAGE_kmod-crypto-kpp=m
CONFIG_PACKAGE_kmod-crypto-lib-chacha20=m
CONFIG_PACKAGE_kmod-crypto-lib-chacha20poly1305=m
CONFIG_PACKAGE_kmod-crypto-lib-curve25519=m
CONFIG_PACKAGE_kmod-crypto-lib-poly1305=m
CONFIG_PACKAGE_kmod-crypto-rng=y
CONFIG_PACKAGE_kmod-crypto-seqiv=y
CONFIG_PACKAGE_kmod-crypto-sha512=y
CONFIG_PACKAGE_kmod-cryptodev=y
CONFIG_PACKAGE_kmod-dummy=m
CONFIG_PACKAGE_kmod-ifb=y
CONFIG_PACKAGE_kmod-ip6tables=y
CONFIG_PACKAGE_kmod-ipt-conntrack=y
CONFIG_PACKAGE_kmod-ipt-conntrack-extra=m
CONFIG_PACKAGE_kmod-ipt-core=y
CONFIG_PACKAGE_kmod-ipt-filter=y
CONFIG_PACKAGE_kmod-ipt-ipopt=y
CONFIG_PACKAGE_kmod-ipt-iprange=y
CONFIG_PACKAGE_kmod-ipt-ipset=y
CONFIG_PACKAGE_kmod-ipt-raw=m
CONFIG_PACKAGE_kmod-ipt-raw6=y
CONFIG_PACKAGE_kmod-lib-textsearch=y
CONFIG_PACKAGE_kmod-mac80211=y
CONFIG_PACKAGE_kmod-mii=m
CONFIG_PACKAGE_kmod-mt76=m
CONFIG_PACKAGE_kmod-mtd-rw=m
CONFIG_PACKAGE_kmod-nf-conncount=m
CONFIG_PACKAGE_kmod-nf-conntrack-netlink=y
CONFIG_PACKAGE_kmod-nf-ipt=y
CONFIG_PACKAGE_kmod-nf-ipt6=y
CONFIG_PACKAGE_kmod-nft-compat=y
CONFIG_PACKAGE_kmod-sched=m
CONFIG_PACKAGE_kmod-sched-cake=y
CONFIG_PACKAGE_kmod-sched-core=y
CONFIG_PACKAGE_kmod-udptunnel4=m
CONFIG_PACKAGE_kmod-udptunnel6=m
CONFIG_PACKAGE_kmod-usb-net=m
CONFIG_PACKAGE_kmod-usb-net-cdc-ether=m
CONFIG_PACKAGE_kmod-usb-net-rndis=m
CONFIG_PACKAGE_kmod-wireguard=m
CONFIG_PACKAGE_libatomic=y
CONFIG_PACKAGE_libcap=y
CONFIG_PACKAGE_libcurl=y
CONFIG_PACKAGE_libevent2=y
CONFIG_PACKAGE_libevent2-core=y
CONFIG_PACKAGE_libevent2-pthreads=y
CONFIG_PACKAGE_libexpat=m
CONFIG_PACKAGE_libgcrypt=y
CONFIG_PACKAGE_libgpg-error=y
CONFIG_PACKAGE_libiperf3=m
CONFIG_PACKAGE_libipset=y
CONFIG_PACKAGE_libiptext=y
CONFIG_PACKAGE_libiptext-nft=y
CONFIG_PACKAGE_libiptext6=y
CONFIG_PACKAGE_libiwinfo-lua=y
CONFIG_PACKAGE_libltdl=y
CONFIG_PACKAGE_liblua=y
CONFIG_PACKAGE_liblucihttp=y
CONFIG_PACKAGE_liblucihttp-lua=y
CONFIG_PACKAGE_liblucihttp-ucode=y
CONFIG_PACKAGE_libmbedtls=m
CONFIG_PACKAGE_libncurses=y
CONFIG_PACKAGE_libnghttp2=y
CONFIG_PACKAGE_libopenssl=y
CONFIG_PACKAGE_libopenssl-conf=y
CONFIG_PACKAGE_libopenssl-devcrypto=y
CONFIG_PACKAGE_libopenssl-legacy=y
CONFIG_PACKAGE_libpcap=y
CONFIG_PACKAGE_libqrencode=y
CONFIG_PACKAGE_librrd1=y
CONFIG_PACKAGE_librt=y
CONFIG_PACKAGE_libubus-lua=y
CONFIG_PACKAGE_libunbound=y
CONFIG_PACKAGE_libunbound_ipset=y
CONFIG_PACKAGE_libunbound_libevent=y
CONFIG_PACKAGE_libunbound_libpthread=y
CONFIG_PACKAGE_libustream-mbedtls=m
CONFIG_PACKAGE_libustream-openssl=y
CONFIG_PACKAGE_libxtables=y
CONFIG_PACKAGE_lua=y
CONFIG_PACKAGE_luci=m
CONFIG_PACKAGE_luci-app-adblock=m
CONFIG_PACKAGE_luci-app-attendedsysupgrade=m
CONFIG_PACKAGE_luci-app-commands=y
CONFIG_PACKAGE_luci-app-dawn=y
CONFIG_PACKAGE_luci-app-ddns=y
CONFIG_PACKAGE_luci-app-diag-core=y
CONFIG_PACKAGE_luci-app-firewall=y
CONFIG_PACKAGE_luci-app-nlbwmon=y
CONFIG_PACKAGE_luci-app-opkg=y
CONFIG_PACKAGE_luci-app-sqm=y
CONFIG_PACKAGE_luci-app-statistics=y
CONFIG_PACKAGE_luci-app-unbound=y
CONFIG_PACKAGE_luci-app-watchcat=m
CONFIG_PACKAGE_luci-app-wifischedule=y
CONFIG_PACKAGE_luci-app-wol=m
CONFIG_PACKAGE_luci-base=y
CONFIG_PACKAGE_luci-compat=y
CONFIG_PACKAGE_luci-lib-base=y
CONFIG_PACKAGE_luci-lib-ip=y
CONFIG_PACKAGE_luci-lib-ipkg=y
CONFIG_PACKAGE_luci-lib-iptparser=y
CONFIG_PACKAGE_luci-lib-json=y
CONFIG_PACKAGE_luci-lib-jsonc=y
CONFIG_PACKAGE_luci-lib-nixio=y
CONFIG_PACKAGE_luci-light=y
CONFIG_PACKAGE_luci-lua-runtime=y
CONFIG_PACKAGE_luci-mod-admin-full=y
CONFIG_PACKAGE_luci-mod-dashboard=m
CONFIG_PACKAGE_luci-mod-network=y
CONFIG_PACKAGE_luci-mod-status=y
CONFIG_PACKAGE_luci-mod-system=y
CONFIG_PACKAGE_luci-proto-bonding=m
CONFIG_PACKAGE_luci-proto-ipv6=y
CONFIG_PACKAGE_luci-proto-ppp=y
CONFIG_PACKAGE_luci-proto-wireguard=m
CONFIG_PACKAGE_luci-ssl-openssl=y
CONFIG_PACKAGE_luci-theme-bootstrap=y
CONFIG_PACKAGE_nlbwmon=y
CONFIG_PACKAGE_ntp-utils=y
CONFIG_PACKAGE_odhcpd=y
CONFIG_PACKAGE_odhcpd-ipv6only=m
CONFIG_PACKAGE_odhcpd_full_ext_cer_id=0
CONFIG_PACKAGE_openssl-util=y
CONFIG_PACKAGE_proto-bonding=m
CONFIG_PACKAGE_px5g-standalone=y
CONFIG_PACKAGE_qrencode=y
CONFIG_PACKAGE_rpcd=y
CONFIG_PACKAGE_rpcd-mod-file=y
CONFIG_PACKAGE_rpcd-mod-iwinfo=y
CONFIG_PACKAGE_rpcd-mod-luci=y
CONFIG_PACKAGE_rpcd-mod-rpcsys=m
CONFIG_PACKAGE_rpcd-mod-rrdns=y
CONFIG_PACKAGE_rpcd-mod-ucode=y
CONFIG_PACKAGE_rrdtool1=y
CONFIG_PACKAGE_sqm-scripts=y
CONFIG_PACKAGE_sqm-scripts-extra=m
CONFIG_PACKAGE_tc-tiny=y
CONFIG_PACKAGE_terminfo=y
CONFIG_PACKAGE_tmux=y
CONFIG_PACKAGE_ucode-mod-html=y
CONFIG_PACKAGE_ucode-mod-lua=y
CONFIG_PACKAGE_ucode-mod-math=y
CONFIG_PACKAGE_uhttpd=y
CONFIG_PACKAGE_uhttpd-mod-ubus=y
CONFIG_PACKAGE_umdns=y
CONFIG_PACKAGE_unbound-anchor=m
CONFIG_PACKAGE_unbound-control=m
CONFIG_PACKAGE_unbound-daemon=y
CONFIG_PACKAGE_usteer=y
CONFIG_PACKAGE_watchcat=m
CONFIG_PACKAGE_wifi-scripts=y
CONFIG_PACKAGE_wifischedule=y
CONFIG_PACKAGE_wireguard-tools=m
CONFIG_PACKAGE_wireless-regdb=y
CONFIG_PACKAGE_wpa-supplicant-openssl=m
CONFIG_PACKAGE_wpad-basic-mbedtls=m
CONFIG_PACKAGE_wpad-openssl=y
CONFIG_PACKAGE_xtables-nft=y
CONFIG_PACKAGE_zlib=y
CONFIG_PREINITOPT=y
CONFIG_TARGET_PREINIT_BROADCAST="10.0.0.255"
CONFIG_TARGET_PREINIT_IP="10.0.0.254"
CONFIG_TESTING_KERNEL=y
# CONFIG_LIBCURL_FTP is not set
```
### Terms
- [X] I am reporting an issue for OpenWrt, not an unsupported fork.