Well, if the GPIOs are the same, then the Lantiq image for the 3490 might at least boot on the 7490.
1 Like
BTW This is what I can find on GPIO, device 7490:
[ 0.620000] Lantiq GPIO driver, version 1.3.2, (c) 2001-2013 Lantiq Deutschland GmbH
[ 8.830000] [LED] use GPIO 45 for 'gpio_avm_led_power'
[ 8.830000] [LED] use GPIO 47 for 'gpio_avm_led_internet'
[ 8.840000] [LED] use GPIO 36 for 'gpio_avm_led_festnetz'
[ 8.840000] [LED] use GPIO 35 for 'gpio_avm_led_wlan'
[ 8.850000] [LED] use GPIO 33 for 'gpio_avm_led_info'
[ 8.850000] [LED] use GPIO 46 for 'gpio_avm_led_info_red'
[ 8.860000] [BUTTON] use GPIO 29 for 'gpio_avm_button_wlan'
[ 8.860000] [BUTTON] use GPIO 1 for 'gpio_avm_button_dect'
[ 9.770000] [piglet]use settings for 185(7 gpios from hw_config)
root@fritz:/# find /proc | grep gpio
/proc/gpio
/proc/irq/160/gpio pushbuttons
/proc/irq/129/gpio pushbuttons
/proc/driver/ifx_gpio
/proc/driver/ifx_gpio/slewrate
/proc/driver/ifx_gpio/slewrate/gpio8
/proc/driver/ifx_gpio/slewrate/gpio18
/proc/driver/ifx_gpio/slewrate/gpio19
/proc/driver/ifx_gpio/slewrate/mii0_tx
/proc/driver/ifx_gpio/slewrate/mii0_rx
/proc/driver/ifx_gpio/slewrate/mii1_tx
/proc/driver/ifx_gpio/slewrate/mii1_rx
/proc/driver/ifx_gpio/slewrate/mii2_tx
/proc/driver/ifx_gpio/slewrate/mii2_rx
/proc/driver/ifx_gpio/slewrate/pciclk
/proc/driver/ifx_gpio/board
/proc/driver/ifx_gpio/module
/proc/driver/ifx_gpio/setup
/proc/driver/ifx_gpio/dbg
/proc/driver/ifx_gpio/version
And this.. Not sure waht it means 
root@fritz:/# cat /proc/driver/ifx_gpio/setup
IFX GPIO Pin Settings
OUT : FEDCBA9876543210
-------------------------
P0: XXX X
P1: X X XXX
P2: XX X X XXX
P3:
~~~~~~~~~~~~~~~~~~~~~~~~~
IN : FEDCBA9876543210
-------------------------
P0: XX XXX XX XXX
P1: XXXXXX XXXXX XX
P2: XX X XX XX X XXX
P3: XX
~~~~~~~~~~~~~~~~~~~~~~~~~
DIR : FEDCBA9876543210
-------------------------
P0: XXXX X X X
P1: XX X XXXXXX XX
P2: XXXXX XXXXXX
P3: X
~~~~~~~~~~~~~~~~~~~~~~~~~
ALTSEL0: FEDCBA9876543210
-------------------------
P0: XXX X X X XX
P1: X XXXX XXX
P2: XX
P3: XX
~~~~~~~~~~~~~~~~~~~~~~~~~
ALTSEL1: FEDCBA9876543210
-------------------------
P0: XX X
P1: X
P2: XX
P3:
~~~~~~~~~~~~~~~~~~~~~~~~~
OD : FEDCBA9876543210
-------------------------
P0: XXXX XX X X X
P1: XX X XXXXXX XXX
P2: XXXXXX XXXXXX
P3: X
~~~~~~~~~~~~~~~~~~~~~~~~~
STOFF : FEDCBA9876543210
-------------------------
P0:
P1:
P2:
P3:
~~~~~~~~~~~~~~~~~~~~~~~~~
PUDSEL : FEDCBA9876543210
-------------------------
P0: XX X
P1: X X X X X
P2: X XXX X X
P3:
~~~~~~~~~~~~~~~~~~~~~~~~~
PUDEN : FEDCBA9876543210
-------------------------
P0: X X
P1: X X XX X X X
P2: X XXX X
P3:
If I can help port this device (7490) let me know what I can do..
I will help..
Please post your efforts in the 7490 porting thread (Support Fritzbox 7490). You are likely to get more response there, since this is the 3490 porting thread (although the two devices seem very similar).
3 Likes
I have tested the USB patch on an 7490 with USB power on..
I tested a few times with USB stick.:
[ 586.296119] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1
[ 586.301462] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
[ 586.307914] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 586.313052] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[ 586.325917] xhci_hcd 0000:01:00.0: hcc params 0x014051cf hci version 0x100 quirks 0x0000000100000090
[ 586.336049] hub 1-0:1.0: USB hub found
[ 586.338823] hub 1-0:1.0: 2 ports detected
[ 586.343984] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 586.348032] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[ 586.355360] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[ 586.362085] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 586.371567] hub 2-0:1.0: USB hub found
[ 586.374613] hub 2-0:1.0: 2 ports detected
[ 586.677664] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[ 586.814141] usb 1-1: device descriptor read/64, error 18
[ 587.054126] usb 1-1: device descriptor read/64, error 18
[ 587.293608] usb 1-1: new high-speed USB device number 3 using xhci_hcd
[ 587.426124] usb 1-1: device descriptor read/64, error 18
[ 587.666106] usb 1-1: device descriptor read/64, error 18
[ 587.777839] usb usb1-port1: attempt power cycle
[ 588.429563] usb 1-1: new high-speed USB device number 4 using xhci_hcd
[ 588.456225] usb 1-1: device descriptor read/all, error -61
[ 588.589557] usb 1-1: new high-speed USB device number 5 using xhci_hcd
[ 588.616213] usb 1-1: device descriptor read/all, error -61
[ 588.620628] usb usb1-port1: unable to enumerate USB device
[ 715.441287] usb 1-2: new high-speed USB device number 6 using xhci_hcd
[ 715.577804] usb 1-2: device descriptor read/64, error 18
[ 715.817805] usb 1-2: device descriptor read/64, error 18
[ 716.057302] usb 1-2: new high-speed USB device number 7 using xhci_hcd
[ 716.193782] usb 1-2: device descriptor read/64, error 18
[ 716.433767] usb 1-2: device descriptor read/64, error 18
[ 716.545520] usb usb1-port2: attempt power cycle
[ 717.197281] usb 1-2: new high-speed USB device number 8 using xhci_hcd
[ 717.224006] usb 1-2: device descriptor read/all, error -61
[ 717.357254] usb 1-2: new high-speed USB device number 9 using xhci_hcd
[ 717.383743] usb 1-2: device descriptor read/all, error -61
[ 717.388163] usb usb1-port2: unable to enumerate USB device
Hi, I also have a FRITZ!Box 3490 to play around. I'm happy to help, although I'm not experienced in openwrt development.
1 Like
can you tell me if i can safely buy a fb 3490? is it fully supported?
Did you actually read this thread? It is not supported at all. The only way you can get OpenWrt on this device is by building my experimental OpenWrt tree yourself.
1 Like
Yes i read. I'm willing to compile your git tree. But i can't read out if it is fully working. (2.4ghz and 5ghz chip at same time). My first try to compile origin/avm_fritz3490 branch ends with error:
[root@t420]: /opt/sources/openwrt-fb3490># make menuconfig
fatal: Invalid revision range ee53a240ac902dc83209008a2671e7fdcf55957a..HEAD
fatal: Invalid revision range ee53a240ac902dc83209008a2671e7fdcf55957a..41126ccba6bb7929fcc46e81f3b12d0cb55cd35e
fatal: Invalid revision range ee53a240ac902dc83209008a2671e7fdcf55957a..HEAD
fatal: Invalid revision range ee53a240ac902dc83209008a2671e7fdcf55957a..41126ccba6bb7929fcc46e81f3b12d0cb55cd35e
WARNING: Makefile 'package/utils/busybox/Makefile' has a dependency on 'libpam', which does not exist
WARNING: Makefile 'package/utils/busybox/Makefile' has a build dependency on 'libpam', which does not exist
WARNING: Makefile 'package/network/utils/curl/Makefile' has a dependency on 'libgnutls', which does not exist
WARNING: Makefile 'package/network/utils/curl/Makefile' has a dependency on 'libopenldap', which does not exist
WARNING: Makefile 'package/network/utils/curl/Makefile' has a dependency on 'libidn2', which does not exist
WARNING: Makefile 'package/network/utils/curl/Makefile' has a dependency on 'libssh2', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-mesh-openssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-mesh-wolfssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-basic', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-mini', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-openssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-wolfssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpa-supplicant', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpa-supplicant-mesh-openssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpa-supplicant-mesh-wolfssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpa-supplicant-basic', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpa-supplicant-mini', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpa-supplicant-p2p', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpa-supplicant-openssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpa-supplicant-wolfssl||', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_hostapd-basic', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_hostapd-mini', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_hostapd-openssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_hostapd-wolfssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-mesh-openssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-mesh-wolfssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-basic', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-mini', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-openssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-wolfssl||', which does not exist
WARNING: Makefile 'package/network/utils/iproute2/Makefile' has a dependency on 'libcap', which does not exist
WARNING: Makefile 'package/network/utils/iproute2/Makefile' has a dependency on 'libcap', which does not exist
WARNING: Makefile 'package/network/utils/iproute2/Makefile' has a dependency on 'libcap', which does not exist
WARNING: Makefile 'package/network/utils/iproute2/Makefile' has a dependency on 'libcap', which does not exist
WARNING: Makefile 'package/network/utils/iproute2/Makefile' has a dependency on 'libcap', which does not exist
WARNING: Makefile 'package/network/utils/iproute2/Makefile' has a dependency on 'libcap', which does not exist
WARNING: Makefile 'package/network/utils/iproute2/Makefile' has a dependency on 'libcap', which does not exist
WARNING: Makefile 'package/network/utils/iproute2/Makefile' has a dependency on 'libcap', which does not exist
WARNING: Makefile 'package/boot/kexec-tools/Makefile' has a dependency on 'liblzma', which does not exist
WARNING: Makefile 'package/network/services/lldpd/Makefile' has a dependency on 'libnetsnmp', which does not exist
WARNING: Makefile 'package/network/utils/nftables/Makefile' has a dependency on 'jansson', which does not exist
tmp/.config-package.in:21668: syntax error
tmp/.config-package.in:21667: invalid option
tmp/.config-package.in:22516: syntax error
tmp/.config-package.in:22515: invalid option
make: *** [/opt/sources/openwrt-fb3490/include/toplevel.mk:142: menuconfig] Fehler 1
[root@t420]: /opt/sources/openwrt-fb3490># git status
Auf Branch avm_fritz3490
Ihr Branch ist auf demselben Stand wie 'origin/avm_fritz3490'.
nichts zu committen, Arbeitsverzeichnis unverändert
Did you only check out the branch or the complete repo? Your Invalid revision range errors could be due to only the branch being available.
It looks like you also didn't download and install the package feeds. Read up on how to compile OpenWrt from source in the Wiki.
That said, the branch is several months old so you might need to port the changes to the current OpenWrt tree if packages don't compile.
Generally, I had both WiFis working at the time I published the branch - with very limited testing, so I have no experience with stability etc.
what i did:
git clone https://github.com/andyboeh/openwrt.git
cd openwrt
git switch avm_fritz3490
make menuconfig
and i still get the error above.
ok, i'll try the other way around.
integrate your changes to the current openwrt sources.
You need to to run:
./scripts feeds update -a
./scripts feeds install -a
After git switch avm_fritz3490
makes no difference. still the same. (without invalid version lines)
[root@t420]: /opt/sources/openwrt-fb3490># make menuconfig
WARNING: Makefile 'package/feeds/packages/apache/Makefile' has a dependency on 'jansson', which does not exist
WARNING: Makefile 'package/feeds/telephony/asterisk-16.x/Makefile' has a dependency on 'jansson', which does not exist
WARNING: Makefile 'package/feeds/packages/bcm27xx-eeprom/Makefile' has a dependency on 'bcm27xx-userland', which does not exist
WARNING: Makefile 'package/feeds/packages/gnunet/Makefile' has a dependency on 'jansson', which does not exist
WARNING: Makefile 'package/feeds/packages/gnunet/Makefile' has a dependency on 'jansson', which does not exist
WARNING: Makefile 'package/feeds/packages/gnunet/Makefile' has a dependency on 'jansson', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-mesh-openssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-mesh-wolfssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-basic', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-mini', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-openssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-wolfssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpa-supplicant', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpa-supplicant-mesh-openssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpa-supplicant-mesh-wolfssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpa-supplicant-basic', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpa-supplicant-mini', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpa-supplicant-p2p', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpa-supplicant-openssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpa-supplicant-wolfssl||', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_hostapd-basic', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_hostapd-mini', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_hostapd-openssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_hostapd-wolfssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-mesh-openssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-mesh-wolfssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-basic', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-mini', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-openssl', which does not exist
WARNING: Makefile 'package/network/services/hostapd/Makefile' has a dependency on 'PACKAGE_wpad-wolfssl||', which does not exist
WARNING: Makefile 'package/feeds/packages/jose/Makefile' has a dependency on 'jansson', which does not exist
WARNING: Makefile 'package/feeds/telephony/kamailio-5.x/Makefile' has a dependency on 'jansson', which does not exist
WARNING: Makefile 'package/feeds/telephony/kamailio-5.x/Makefile' has a dependency on 'jansson', which does not exist
WARNING: Makefile 'package/feeds/packages/libsearpc/Makefile' has a dependency on 'jansson', which does not exist
WARNING: Makefile 'package/network/utils/nftables/Makefile' has a dependency on 'jansson', which does not exist
WARNING: Makefile 'package/feeds/packages/samba4/Makefile' has a dependency on 'jansson', which does not exist
WARNING: Makefile 'package/feeds/packages/seafile-ccnet/Makefile' has a dependency on 'jansson', which does not exist
WARNING: Makefile 'package/feeds/packages/seafile-server/Makefile' has a dependency on 'jansson', which does not exist
WARNING: Makefile 'package/feeds/packages/seafile-server/Makefile' has a dependency on 'jansson', which does not exist
WARNING: Makefile 'package/feeds/packages/sqm-scripts/Makefile' has a dependency on 'kmod-sched-cake-oot', which does not exist
WARNING: Makefile 'package/feeds/packages/ulogd/Makefile' has a dependency on 'jansson', which does not exist
WARNING: Makefile 'package/feeds/packages/yara/Makefile' has a dependency on 'jansson', which does not exist
tmp/.config-package.in:63305:warning: leading whitespace ignored
tmp/.config-package.in:130680: syntax error
tmp/.config-package.in:130679: invalid option
tmp/.config-package.in:135389: syntax error
tmp/.config-package.in:135388: invalid option
tmp/.config-package.in:149144: syntax error
tmp/.config-package.in:149143: invalid option
make: *** [/opt/sources/openwrt-fb3490/include/toplevel.mk:142: menuconfig] Error 1
This is probably because my repository is from February while the package feed is newer. I suspect that some base packages have changed in the meantime.
basically what do i have to do to make this work on the current openwrt tree? is there some easy way?
do i have to apply all changes from this?: https://github.com/andyboeh/openwrt/commit/41126ccba6bb7929fcc46e81f3b12d0cb55cd35e
and what is avm_fritzbox3490_wasp? (wasp?)
Yes
I explained how it all works together in the 7490 porting thread just a few hours ago: Support Fritzbox 7490 - #63 by andyboeh
is it possible to merge that commit to the current branch with just a few git commands (git-cherry-pick?)? i would really appreciate it if someone can make me a step by step tutorial for the current branch. i will get my fritzbox 3490 today and i have the feeling i will never get this to work until it's officially supported... 
I'm sorry to say that, but: At least from my side, there won't be a step-by-step guide and it won't be officially supported. Personally, I'm done with 3390 and 3490.
For official support, a lot of changes are necessary, including writing a kernel module for uploading the WiFi files. There was a lengthy discussion on this in the 3390 PR at https://github.com/openwrt/openwrt/pull/2662. I abandoned the work on it because nobody cared (and it works for me). Feel free to carry on the work.
i dont understand how nobody cares 
... this is excelent dsl router hardware for openwrt. is there any comparable that is official supported? i'm running fritzbox 3370 at the moment, but has no dual 2.4/5ghz support.