OpenWrt support for Netgear WAX620

For Developers
1

Ahoy,
Now that the WAX218, I picked up a WAX620 to figure out.
Internal photos aren't available online, I'll follow up with those. The board has a different layout, from the WAX218, with different LEDs. Same case, and antenna layout. And same general hardware:

IQP8072a
RAM 512MiB
Flash : NAND 256 MiB

Bootlog: (serial : 115200 / 8N1 / No handshake)

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00163
S - IMAGE_VARIANT_STRING=HAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e5
B -       203 - PBL, Start
B -      2740 - bootable_media_detect_entry, Start
B -      3448 - bootable_media_detect_success, Start
B -      3453 - elf_loader_entry, Start
B -      6122 - auth_hash_seg_entry, Start
B -      6365 - auth_hash_seg_exit, Start
B -     68354 - elf_segs_hash_verify_entry, Start
B -    131210 - PBL, End
B -    218837 - SBL1, Start
B -    298595 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B -    308538 - pm_device_init, Start
B -    493551 - PM_SET_VAL:Skip
D -    183030 - pm_device_init, Delta
B -    495960 - pm_driver_init, Start
D -      5368 - pm_driver_init, Delta
B -    502335 - clock_init, Start
D -      2135 - clock_init, Delta
B -    506269 - boot_flash_init, Start
D -     12444 - boot_flash_init, Delta
B -    522495 - boot_config_data_table_init, Start
D -      3080 - boot_config_data_table_init, Delta - (575 Bytes)
B -    529968 - Boot Setting :  0x00000618
B -    533902 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:6
B -    540826 - sbl1_ddr_set_params, Start
B -    544638 - CPR configuration: 0x30c
B -    548085 - cpr_init, Start
B -    550860 - Rail:0 Mode: 5 Voltage: 816000
B -    556076 - CL CPR settled at 768000mV
B -    558882 - Rail:1 Mode: 5 Voltage: 880000
B -    563091 - Rail:1 Mode: 7 Voltage: 904000
D -     16500 - cpr_init, Delta
B -    569953 - Pre_DDR_clock_init, Start
B -    573979 - Pre_DDR_clock_init, End
B -    577365 - DDR Type : PCDDR4
B -    583983 - do ddr sanity test, Start
D -      1067 - do ddr sanity test, Delta
B -    587765 - DDR: Start of HAL DDR Boot Training
B -    592523 - DDR: End of HAL DDR Boot Training
B -    598196 - DDR: Checksum to be stored on flash is -495557553
B -    608627 - Image Load, Start
D -    222253 - QSEE Image Loaded, Delta - (1371968 Bytes)
B -    830942 - Image Load, Start
D -        61 - SEC Image Loaded, Delta - (0 Bytes)
B -    838628 - Image Load, Start
D -     10675 - DEVCFG Image Loaded, Delta - (26088 Bytes)
B -    849394 - Image Load, Start
D -     22021 - RPM Image Loaded, Delta - (86660 Bytes)
B -    871507 - Image Load, Start
D -     91042 - APPSBL Image Loaded, Delta - (559610 Bytes)
B -    962671 - QSEE Execution, Start
D -        61 - QSEE Execution, Delta
B -    968497 - USB D+ check, Start
D -         0 - USB D+ check, Delta
B -    974871 - SBL1, End
D -    758352 - SBL1, Delta
S - Flash Throughput, 6741 KB/s  (2045573 Bytes,  303408 us)
S - DDR Frequency, 600 MHz
S - Core 0 Frequency, 1651 MHz


U-Boot 2016.01-V9.5.0.7 (Jan 20 2021 - 09:15:03 -0800)

DRAM:  smem ram ptable found: ver: 1 len: 4
1 GiB
NAND:  Could not find nand_gpio in dts, using defaults
ONFI device found
ID = 1590aac2
Vendor = c2
Device = aa
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
256 MiB
MMC:   sdhci: Node Not found, skipping initialization

PCI0 is not defined in the device tree
PCI1 is not defined in the device tree
In:    serial@78B3000
Out:   serial@78B3000
Err:   serial@78B3000
Product ID: WAX620
HW Version: 1.0
machid: 8010006
adp_value:1, poe_value:1
Power Source: PoE 802.3at
MMC Device 0 not found
eth2 MAC Address from ART is not valid
eth3 MAC Address from ART is not valid
eth4 MAC Address from ART is not valid
eth5 MAC Address from ART is not valid
Hit any key to stop autoboot:  0
Erasing NAND...
Erasing at 0xd60000 -- 100% complete.
Writing to NAND... OK
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=0", size 60 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 480, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 7/2, WL threshold: 4096, image sequence number: 1120416420
ubi0: available PEBs: 0, total reserved PEBs: 480, PEBs reserved for bad PEB handling: 40
Read 0 bytes from volume kernel to 44000000
No size specified -> Using max size (6094848)
## Loading kernel from FIT Image at 44000000 ...
   Using 'config@hk07' configuration
   Trying 'kernel@1' kernel subimage
     Description:  ARM OpenWrt Linux-4.4.60
     Type:         Kernel Image
     Compression:  gzip compressed
     Data Start:   0x440000e4
     Data Size:    3923165 Bytes = 3.7 MiB
     Architecture: ARM
     OS:           Linux
     Load Address: 0x41208000
     Entry Point:  0x41208000
     Hash algo:    crc32
     Hash value:   589d5a6d
     Hash algo:    sha1
     Hash value:   b924441063f7d39ccdc078ad5418e446d5608f68
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
   Using 'config@hk07' configuration
   Trying 'fdt@hk07' fdt subimage
     Description:  ARM OpenWrt qcom-ipq807x-hkxx device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x443bdf04
     Data Size:    81180 Bytes = 79.3 KiB
     Architecture: ARM
     Hash algo:    crc32
     Hash value:   cd849bdc
     Hash algo:    sha1
     Hash value:   032e67b7a887fda4bf41a737356ccde0e0722b40
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Booting using the fdt blob at 0x443bdf04
   Uncompressing Kernel Image ... OK
   Loading Device Tree to 4a3e9000, end 4a3ffd1b ... OK
Could not find PCI in device tree
Using machid 0x8010006 from environment

Starting kernel ...
2

boot output continued:

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.60-V10.4.0.5 (dineshkb@NTGUSTNC) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 e330ccd+r49254) ) #5 SMP PREEMPT Wed Mar 1 22:34:12 GMT 2023
[    0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c0383d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Qualcomm Technologies, Inc. IPQ807x/AP-HK07
[    0.000000] Ignoring memory range 0x40000000 - 0x41000000
[    0.000000] Reserved memory: OVERLAP DETECTED!
[    0.000000] wifi_dump@51100000 (0x51100000--0x51700000) overlaps with wigig_dump@51300000 (0x51300000--0x51700000)
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] PERCPU: Embedded 11 pages/cpu @be6b4000 s14592 r8192 d22272 u45056
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 226340
[    0.000000] Kernel command line: WAX620 1.0 console=ttyMSM0,115200n8 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait swiotlb=1 coherent_pool=2M
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 894096K/914432K available (6302K kernel code, 371K rwdata, 1896K rodata, 1024K init, 326K bss, 20336K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xbf800000 - 0xff800000   (1024 MB)
[    0.000000]     lowmem  : 0x80000000 - 0xbf000000   (1008 MB)
[    0.000000]     pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
[    0.000000]     modules : 0x7f000000 - 0x7fe00000   (  14 MB)
[    0.000000]       .text : 0x80208000 - 0x80b019f8   (9191 kB)
[    0.000000]       .init : 0x80c00000 - 0x80d00000   (1024 kB)
[    0.000000]       .data : 0x80d00000 - 0x80d5cf58   ( 372 kB)
[    0.000000]        .bss : 0x80d5f000 - 0x80db0940   ( 327 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] Architected cp15 timer(s) running at 19.20MHz (virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.000016] Switching to timer-based delay loop, resolution 52ns
[    0.000663] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[    0.000674] pid_max: default: 32768 minimum: 301
[    0.000765] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000774] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.001296] Initializing cgroup subsys io
[    0.001312] Initializing cgroup subsys memory
[    0.001334] Initializing cgroup subsys devices
[    0.001345] Initializing cgroup subsys freezer
[    0.001355] Initializing cgroup subsys net_cls
[    0.001364] Initializing cgroup subsys pids
[    0.001385] CPU: Testing write buffer coherency: ok
[    0.001608] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.001656] Setting up static identity map for 0x41300000 - 0x41300058
[    0.052462] MSM Memory Dump base table set up
[    0.052484] MSM Memory Dump apps data table set up
[    0.090177] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.120165] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.150198] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.150250] Brought up 4 CPUs
[    0.150270] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[    0.150276] CPU: All CPU(s) started in SVC mode.
[    0.171432] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
[    0.171748] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.171769] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.171988] pinctrl core: initialized pinctrl subsystem
[    0.173036] NET: Registered protocol family 16
[    0.174131] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[    0.200034] cpuidle: using governor ladder
[    0.230053] cpuidle: using governor menu
[    0.230289] NET: Registered protocol family 42
[    0.232282] Soc version is not 1, changing clock offsets
[    0.239751] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel !
[    0.242029] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel !
[    0.258226] CPU: IPQ8072A, SoC Version: 2.0
[    0.258780] qcom,cpr3-npu-regulator a4000.npu-cpr: NPU CPR valid fuse count: 2
[    0.259144] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[    0.260011] spmi spmi-0: PMIC Arb Version-2 (0x20010000)
[    0.261711] IPC logging disabled
[    0.261718] IPC logging disabled
[    0.261723] IPC logging disabled
[    0.261727] IPC logging disabled
[    0.261732] IPC logging disabled
[    0.261959] sps:sps is ready.
[    0.292117] pps_core: LinuxPPS API ver. 1 registered
[    0.292125] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.292152] PTP clock support registered
[    0.293807] Advanced Linux Sound Architecture Driver Initialized.
[    0.294592] clocksource: Switched to clocksource arch_sys_counter
[    0.298450] NET: Registered protocol family 2
[    0.299080] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.299165] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.299307] TCP: Hash tables configured (established 8192 bind 8192)
[    0.299357] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.299393] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.299562] NET: Registered protocol family 1
[    0.308139] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.308156] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.312055] Key type asymmetric registered
[    0.312068] Asymmetric key parser 'x509' registered
[    0.312099] io scheduler noop registered
[    0.312109] io scheduler deadline registered (default)
[    0.319785] msm_rpm_log_probe: OK
[    0.320140] msm-dcc b3000.dcc: DCC XPU is not specified
[    0.320401] msm-dcc b3000.dcc: jiffies_64: 0xffff8aef, cntvct_64: 0x5c88451
[    0.320414] msm-dcc b3000.dcc: gcnt_hi: 0x00000000(0xbfb02004)
[    0.320425] msm-dcc b3000.dcc: gcnt_lo: 0x05c8863f(0xbfb02000)
[    0.321068] TZ SMMU State: SMMU Stage2 Enabled
[    0.321120] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set
[    0.322962] msm_serial 78b3000.serial: msm_serial: detected port #0
[    0.323001] msm_serial 78b3000.serial: uartclk = 3686400
[    0.323034] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 23, base_baud = 230400) is a MSM
[    0.323053] msm_serial: console setup on port #0
[    0.984853] console [ttyMSM0] enabled
[    0.989883] msm_serial 78b1000.serial: msm_serial: detected port #1
[    0.993106] msm_serial 78b1000.serial: uartclk = 19200000
[    0.999190] 78b1000.serial: ttyMSM1 at MMIO 0x78b1000 (irq = 24, base_baud = 1200000) is a MSM
[    1.005095] msm_serial: driver initialized
[    1.013550] msm_serial_hsl_init: driver initialized
[    1.026790] brd: module loaded
[    1.027421] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[    1.030387] m25p80 spi32766.0: unrecognized JEDEC id bytes: ff, ff, ff
[    1.036787] QPIC controller hw version Major:1, Minor:5
[    1.042555] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xaa
[    1.047458] nand: ONFI 10-Compliant Macronix MX30UF2G18AC
[    1.053995] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.059434] 26 ofpart partitions found on MTD device qcom_nand.0
[    1.066771] Creating 26 MTD partitions on "qcom_nand.0":
[    1.072921] 0x000000000000-0x000000100000 : "0:SBL1"
[    1.079838] 0x000000100000-0x000000200000 : "0:MIBIB"
[    1.084724] 0x000000200000-0x000000280000 : "0:BOOTCONFIG"
[    1.089279] 0x000000280000-0x000000300000 : "0:BOOTCONFIG1"
[    1.094685] 0x000000300000-0x000000600000 : "0:QSEE"
[    1.102014] 0x000000600000-0x000000900000 : "0:QSEE_1"
[    1.107238] 0x000000900000-0x000000980000 : "0:DEVCFG"
[    1.110241] 0x000000980000-0x000000a00000 : "0:DEVCFG_1"
[    1.115351] 0x000000a00000-0x000000a80000 : "0:APDP"
[    1.120848] 0x000000a80000-0x000000b00000 : "0:APDP_1"
[    1.125797] 0x000000b00000-0x000000b80000 : "0:RPM"
[    1.130751] 0x000000b80000-0x000000c00000 : "0:RPM_1"
[    1.135538] 0x000000c00000-0x000000c80000 : "0:CDT"
[    1.140772] 0x000000c80000-0x000000d00000 : "0:CDT_1"
[    1.145510] 0x000000d00000-0x000000d80000 : "0:APPSBLENV"
[    1.150691] 0x000000d80000-0x000000e80000 : "0:APPSBL"
[    1.156359] 0x000000e80000-0x000000f80000 : "0:APPSBL_1"
[    1.161386] 0x000000f80000-0x000001000000 : "0:ART"
[    1.166517] 0x000001000000-0x000004c00000 : "rootfs"
[    1.215312] mtd: device 18 (rootfs) set to be root filesystem
[    1.215571] mtdsplit: no squashfs found in "rootfs"
[    1.220037] 0x000004c00000-0x000005500000 : "0:WIFIFW"
[    1.232215] 0x000005500000-0x000009100000 : "rootfs_1"
[    1.277580] 0x000009100000-0x000009a00000 : "0:WIFIFW_1"
[    1.285180] 0x000009a00000-0x000009a80000 : "0:ETHPHYFW"
[    1.286397] 0x000009a80000-0x000009c00000 : "0:MFGDATA"
[    1.291387] 0x000009c00000-0x00000e400000 : "0:NTGRDATA"
[    1.345819] 0x00000e400000-0x000010000000 : "0:Oops_log"
[    1.559979] random: nonblocking pool is initialized
[    1.952998] mtdoops: Attached to MTD device 25
[    1.954416] libphy: Fixed MDIO Bus: probed
[    2.177047] qca-mdio 90000.mdio: Could not find phy-reset-gpio
[    2.177177] libphy: qca_mdio: probed
[    2.182284] qca-mdio 90000.mdio: qca-mdio driver was registered
[    2.185728] Unable to create IPC log context!
[    2.191430] Skip QCA8074V1 in V2 platform
[    2.195925] cnss[2]: INFO: Platform driver probed successfully. plat bdb80010 tgt 0xfffe
[    2.199895] i2c /dev entries driver
[    2.214565] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[    2.215065] sdhci: Secure Digital Host Controller Interface driver
[    2.222060] sdhci: Copyright(c) Pierre Ossman
[    2.228071] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.233929] qcom_ice_get_device_tree_data: No vdd-hba-supply regulator, assuming not needed
[    2.238282] ICE IRQ = 27
[    2.246843]
[    2.246843] Version Rollback Feature Disabled
[    2.251580] qcom-q6v5-wcss-pil cd00000.qcom_q6v5_wcss: ssr registeration success qcom_q6v5_wcss
[    2.254818] remoteproc remoteproc0: cd00000.qcom_q6v5_wcss is available
[    2.263882] SPMI VADC - Min ch: 0 Max ch: 15
[    2.271762] of_graph_get_next_endpoint(): no port node found in /soc/csr@6001000
[    2.274503] coresight-csr 6001000.csr: CSR initialized
[    2.281972] of_graph_get_next_endpoint(): no port node found in /soc/cti@6010000
[    2.286948] of_graph_get_next_endpoint(): no port node found in /soc/cti@6011000
[    2.294482] of_graph_get_next_endpoint(): no port node found in /soc/cti@6012000
[    2.301870] of_graph_get_next_endpoint(): no port node found in /soc/cti@6013000
[    2.309256] of_graph_get_next_endpoint(): no port node found in /soc/cti@6014000
[    2.316600] of_graph_get_next_endpoint(): no port node found in /soc/cti@6015000
[    2.323965] of_graph_get_next_endpoint(): no port node found in /soc/cti@6016000
[    2.331359] of_graph_get_next_endpoint(): no port node found in /soc/cti@6017000
[    2.338751] of_graph_get_next_endpoint(): no port node found in /soc/cti@6018000
[    2.346119] of_graph_get_next_endpoint(): no port node found in /soc/cti@6019000
[    2.353485] of_graph_get_next_endpoint(): no port node found in /soc/cti@601a000
[    2.360878] of_graph_get_next_endpoint(): no port node found in /soc/cti@601b000
[    2.368264] of_graph_get_next_endpoint(): no port node found in /soc/cti@601c000
[    2.375641] of_graph_get_next_endpoint(): no port node found in /soc/cti@601d000
[    2.383001] of_graph_get_next_endpoint(): no port node found in /soc/cti@601e000
[    2.390399] of_graph_get_next_endpoint(): no port node found in /soc/cti@601f000
[    2.397774] of_graph_get_next_endpoint(): no port node found in /soc/cti@6198000
[    2.405164] of_graph_get_next_endpoint(): no port node found in /soc/cti@6199000
[    2.412527] of_graph_get_next_endpoint(): no port node found in /soc/cti@619a000
[    2.419931] of_graph_get_next_endpoint(): no port node found in /soc/cti@619b000
[    2.427310] of_graph_get_next_endpoint(): no port node found in /soc/cti@610c000
[    2.434835] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x06044000
[    2.441859] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x06044000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x06044000
[    2.457581] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x06044000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x06044000
[    2.472077] sps:BAM 0x06044000 is registered.[    2.479135] coresight-tmc 6028000.tmc: TMC initialized
[    2.483155] coresight-tmc 6027000.tmc: TMC initialized
[    2.488319] coresight-funnel 6021000.funnel: FUNNEL initialized
[    2.493323] coresight-funnel 6100000.funnel: FUNNEL initialized
[    2.499148] coresight-funnel 6120000.funnel: FUNNEL initialized
[    2.505050] coresight-funnel 6130000.funnel: FUNNEL initialized
[    2.510954] coresight-funnel 61a1000.funnel: FUNNEL initialized
[    2.517506] coresight-etm4x 619c000.etm: ETM 4.0 initialized
[    2.523100] coresight-etm4x 619d000.etm: ETM 4.0 initialized
[    2.529031] coresight-etm4x 619e000.etm: ETM 4.0 initialized
[    2.534693] coresight-etm4x 619f000.etm: ETM 4.0 initialized
[    2.539978] coresight-replicator-qcom 6026000.replicator: REPLICATOR 1.0 initialized
[    2.545757] coresight-stm 6002000.stm: STM initialized
[    2.554320] of_graph_get_next_endpoint(): no port node found in /soc/hwevent@6101000
[    2.558141] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized
[    2.569684] NET: Registered protocol family 10
[    2.573994] NET: Registered protocol family 17
[    2.577599] bridge_nlevent_init: Initializing Bridge HTTP redirect event mechanism
[    2.581961] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    2.589570] br: HTTP redirect disabled
[    2.602314] Bridge firewalling registered
[    2.605846] 8021q: 802.1Q VLAN Support v1.8
[    2.610191] Registering SWP/SWPB emulation handler
[    2.615006] qcom,cpr3-npu-regulator a4000.npu-cpr: NPU CPR valid fuse count: 2
[    2.618923] pmd9655_s4: supplied by e-smps1-reg
[    2.626174] cpr3_mem_acc_init: npu: not using memory accelerator regulator
[    2.630398] npu_corner: fused      NOM: open-loop= 792000 uV
[    2.637372] npu_corner: fused    TURBO: open-loop= 856000 uV
[    2.643206] npu_corner: fused      NOM: open-loop= 792000 uV
[    2.648822] npu_corner: fused    TURBO: open-loop= 856000 uV
[    2.654468] npu_corner: Normal and Cold condition init done. Default to normal.
[    2.660421] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[    2.667242] pmd9655_s3: supplied by e-smps1-reg
[    2.674532] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
[    2.678938] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1
[    2.685534] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[    2.693185] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[    2.700715] cpr3_mem_acc_init: apc: not using memory accelerator regulator
[    2.709840] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused      SVS: open-loop= 704000 uV
[    2.716787] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused      NOM: open-loop= 808000 uV
[    2.726769] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused    TURBO: open-loop= 872000 uV
[    2.736578] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused   STURBO: open-loop= 968000 uV
[    2.746454] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused      SVS: quot[ 7]= 723, quot_offset[ 7]=   0
[    2.756201] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused      NOM: quot[ 7]= 927, quot_offset[ 7]= 200
[    2.767050] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused    TURBO: quot[ 7]=1040, quot_offset[ 7]= 110
[    2.777988] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused   STURBO: quot[ 7]=1216, quot_offset[ 7]= 175
[    2.789043] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
[    2.800786] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 800000 KHz
[    2.806772] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1017600 KHz
[    2.813983] ubi0: attaching mtd18
[    3.045651] ubi0: scanning is finished
[    3.050660] ubi0: attached mtd18 (name "rootfs", size 60 MiB)
[    3.050678] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    3.055380] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    3.062144] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    3.069007] ubi0: good PEBs: 480, bad PEBs: 0, corrupted PEBs: 0
[    3.075776] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    3.082023] ubi0: max/mean erase counter: 7/2, WL threshold: 4096, image sequence number: 1120416420
[    3.089063] ubi0: available PEBs: 0, total reserved PEBs: 480, PEBs reserved for bad PEB handling: 40
[    3.098358] ubi0: background thread "ubi_bgt0d" started, PID 115
[    3.108297] hctosys: unable to open rtc device (rtc0)
[    3.117864] pmd9655_ldo11: disabling
[    3.118873] ALSA device list:
[    3.122118]   No soundcards found.
[    3.126701] VFS: Mounted root (squashfs filesystem) readonly on device 31:27.
[    3.129343] Freeing unused kernel memory: 1024K (80c00000 - 80d00000)
[    3.353414] init: Console is alive
[    3.353495] init: - watchdog -
[    4.134506] Button Hotplug driver version 0.4.1
[    4.356091] init: - preinit -
Before mount_root
[    4.468001] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 133
[    4.493347] UBIFS (ubi0:2): recovery needed
[    4.556159] UBIFS (ubi0:2): recovery completed
[    4.556217] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[    4.559489] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    4.567404] UBIFS (ubi0:2): FS size: 21966848 bytes (20 MiB, 173 LEBs), journal size 1142784 bytes (1 MiB, 9 LEBs)
[    4.577293] UBIFS (ubi0:2): reserved for root: 1037548 bytes (1013 KiB)
[    4.587529] UBIFS (ubi0:2): media format: w4/r0 (latest is w4/r0), UUID 84B6DACD-2B00-4E8A-B3E0-EC0EA44F169A, small LPT model
[    4.597596] mount_root: switching to jffs2 overlay
After mount_root
12064+0 records in
12064+0 records out
12064 bytes (11.8KB) copied, 0.024986 seconds, 471.5KB/s
131072+0 records in
131072+0 records out
131072 bytes (128.0KB) copied, 0.242708 se[    4.901074] procd: - early -
[    4.903776] procd: - watchdog -
conds, 527.4KB/s
[    5.529025] procd: - ubus -
[    6.531868] procd: - init -
[    6.979399] ubi1: attaching mtd24
[    7.254073] ubi1: scanning is finished
[    7.259188] ubi1: attached mtd24 (name "0:NTGRDATA", size 72 MiB)
[    7.259209] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    7.264250] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    7.271033] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
[    7.277884] ubi1: good PEBs: 576, bad PEBs: 0, corrupted PEBs: 0
[    7.284654] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
[    7.290901] ubi1: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 245356283
[    7.297939] ubi1: available PEBs: 0, total reserved PEBs: 576, PEBs reserved for bad PEB handling: 40
[    7.306891] ubi1: background thread "ubi_bgt1d" started, PID 712
[    7.323277] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 718
[    7.375610] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "SYSCONFIG"
[    7.375634] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    7.382067] UBIFS (ubi1:0): FS size: 66281472 bytes (63 MiB, 522 LEBs), journal size 3301376 bytes (3 MiB, 26 LEBs)
[    7.392148] UBIFS (ubi1:0): reserved for root: 3130637 bytes (3057 KiB)
[    7.402381] UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 8B4891A4-2916-4EC2-A602-D2843C88E91E, small LPT model
 WIFI FW mount is successful

(none) login: [    7.920881] cfg80211: World regulatory domain updated:
[    7.920905] cfg80211:  DFS Master region: unset
[    7.924975] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[    7.929514] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[    7.935809] Initializing XFRM netlink socket
[    7.936285] NET: Registered protocol family 15
[    7.951384] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[    7.955663] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[    7.965034] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[    7.972918] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[    7.982671] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[    7.992138] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[    8.000200] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[    8.708847] ssdk_switch_device_num_init[1108]:INFO:ess-switch dts node number: 1
[    8.708901] ssdk_dt_get_switch_node[936]:INFO:ess-switch DT exist!
[    8.715329] ssdk_dt_parse_access_mode[837]:INFO:switch_access_mode: local bus
[    8.721293] ssdk_dt_parse_access_mode[850]:INFO:switchreg_base_addr: 0x3a000000
[    8.728502] ssdk_dt_parse_access_mode[851]:INFO:switchreg_size: 0x1000000
[    8.735620] ssdk_dt_parse_mac_mode[289]:INFO:mac mode = 0x0
[    8.742557] ssdk_dt_parse_mac_mode[298]:INFO:mac mode1 = 0xff
[    8.747944] ssdk_dt_parse_mac_mode[307]:INFO:mac mode2 = 0xf
[    8.753854] ssdk_dt_parse_phy_info[641]:INFO:[PORT 6] port_mac_sel = QGMAC_PORT
[    8.759589] ssdk_dt_parse_uniphy[326]:INFO:ess-uniphy DT exist!
[    8.766767] ssdk_dt_parse_intf_mac[783]:INFO:dp6 MAC 80:cc:9c:5a:a2:1f
[    8.772516] ssdk_plat_init start
[    8.856253] ssdk_gcc_clock_init[938]:INFO:SSDK gcc clock init successfully!
[    8.856427] ssdk_probe[1997]:INFO:ess_rst doesn't exist!
[    8.862553] HPPE initializing...
[    8.867662] ssdk_phy_driver_init[328]:INFO:dev_id = 0, phy_adress = 0, phy_id = 0xffffffff phytype doesn't match
[    8.870807] ssdk_phy_driver_init[328]:INFO:dev_id = 0, phy_adress = 1, phy_id = 0xffffffff phytype doesn't match
[    8.881029] ssdk_phy_driver_init[328]:INFO:dev_id = 0, phy_adress = 2, phy_id = 0xffffffff phytype doesn't match
[    8.891135] ssdk_phy_driver_init[328]:INFO:dev_id = 0, phy_adress = 3, phy_id = 0xffffffff phytype doesn't match
[    8.901290] ssdk_phy_driver_init[328]:INFO:dev_id = 0, phy_adress = 4, phy_id = 0xffffffff phytype doesn't match
[    8.911449] qca808x_phy_api_ops_init[2188]:INFO:qca probe qca808x phy driver succeeded!
[    8.922382] qca808x_ptp_register[1407]:INFO:qca808x ptp clock registered
[    8.929338] regi_init[3525]:INFO:Initializing HPPE!!
[    9.154593] ssdk_ppe_reset_init[1169]:INFO:ppe reset successfully!
[    9.157599] qca_hppe_tdm_hw_init[674]:INFO:tdm setup num=96
[    9.159937] qca_hppe_portctrl_hw_init[105]:INFO:Hawkeye PPE port initializing
[   10.411646] ssdk_switch_register[1691]:INFO:Chip version 0x1500
[   10.411675] qca_link_polling_select[1307]:INFO:link-polling-required node does not exist
[   10.416367] ssdk_switch_register[1717]:INFO:polling is selected
[   10.424696] regi_init[3529]:INFO:Initializing HPPE Done!!
[   10.430388] regi_init[3589]:INFO:qca-ssdk module init succeeded!
[   10.440105] tun: Universal TUN/TAP device driver, 1.6
[   10.441963] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   10.449246] EDMA ver 1 hw init
[   10.453202] EDMA HW Reset completed succesfully
[   10.456109] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7)
[   10.460452] RxDesc:1 (15-15) RxFill:1 (7-7)
[   10.667743] nss_dp_probe: registered lldp0 ether interface
[   10.667823] **********************************************************
[   10.672120] * NSS Data Plane driver
[   10.678680] **********************************************************
[   10.687894] l2tp_core: L2TP core driver, V2.0
[   10.689056] l2tp_netlink: L2TP netlink interface
[   10.835026] nss_driver - fw of size 761364  bytes copied to load addr: 40000000, nss_id : 0
[   10.836252] Supported Frequencies -
[   10.842169] 748.8 MHz 1.4976 GHz
[   10.848153] 1.6896 GHz [   10.849198]
[   10.851554] 7f58af40: set sdma bbaf2200
[   10.853092] 7f58af40: meminfo init succeed
[   10.886992] node size 2 # items 4
[   10.887015] memory: 40000000 1073741824 (avl 938717184) items 4 active_cores 2
[   10.889286] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000
[   10.890324] nss_driver - fw of size 290476  bytes copied to load addr: 40800000, nss_id : 1
[   10.890951] Supported Frequencies -
[   10.890952] 748.8 MHz
[   10.890952] 1.4976 GHz
[   10.890953] 1.6896 GHz
[   10.890953]
[   10.891058] 7f58fbc0: set sdma bbaf2500
[   10.891118] 7f58fbc0: meminfo init succeed
[   10.892565] sit: IPv6 over IPv4 tunneling driver
[   10.893954] nat46: module (version 8ff2ae59ec9840a7b8b45f976c51cae80abe0226) loaded.
[   10.895304] gre: GRE over IPv4 demultiplexor driver
[   10.895745] ip_gre: GRE over IPv4 tunneling driver
[   10.896835] ip6_gre: GRE over IPv6 tunneling driver
[   10.901596] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[   10.901605] MII link monitoring set to 100 ms
[   10.907482] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   10.909778] rmnet_nss_init(): initializing rmnet_nss
[   10.912561] nf_conntrack version 0.5.0 (13986 buckets, 55944 max)
[   10.917067] QCA Hy-Fi multicast installation successfully
[   10.921185] PPP generic driver version 2.4.2
[   10.922272] nss_lag_init[352]:LAG Manager Installed
[   10.923142] NET: Registered protocol family 24
[   10.924747] PPTP driver version 0.8.5
[   10.930513] diag: IPC Logging disabled
[   10.930833] TRACK: P[0]      PMask[4]
[   10.930835] TRACK: P[1]      PMask[4]
[   10.930836] TRACK: P[2]      PMask[4]
[   10.930955] TRACK: P[3]      PMask[4]
[   10.930979] nik 4097 info->svc_id
[   10.932879] QCA multicast snooping installed successfully
[   10.934003] <NSS-CRYPTO>:module loaded Build_ID - 03/01/23, 21:17:47 SoC=ipq807x
[   10.940341] cannot find nss-macsec0 node
[   10.940366] nss-macsec1 DT exist!
[   10.979332] cannot find nss-macsec2 node
[   10.979333] nss_macsec init success
[   10.993085] u32 classifier
[   10.993086]     input device check on
[   10.993087]     Actions configured
[   10.993498] Mirror/redirect action on
3

last bit of boot log

[   11.002230] fuse init (API version 7.23)
[   11.003954] arp_tables: (C) 2002 David S. Miller
[   11.008617] Ebtables v2.0 registered
[   11.009340] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.012218] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[   11.086349] 7f58af40: nss core 0 booted successfully
[   11.091119] node size 2 # items 4
[   11.096060] memory: 40000000 1073741824 (avl 939020288) items 4 active_cores 2
[   11.099270] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000
[   11.106398] 7f58fbc0: nss core 1 booted successfully
[   11.218154] nf_conntrack_rtsp v0.6.21 loading
[   11.407194] nf_nat_rtsp v0.6.21 loading
[   11.409437] PPP MPPE Compression module registered
[   11.422777] xt_time: kernel timezone is -0000
qcawifi configuration is disable
[   15.782977] mem_manager: module license 'Proprietary' taints kernel.
[   15.783003] Disabling lock debugging due to kernel taint
[   17.821287] vmap allocation for size 3145728 failed: use vmalloc=<size> to increase size.
[   18.306678] vmap allocation for size 1482752 failed: use vmalloc=<size> to increase size.
[   18.503371] vmap allocation for size 819200 failed: use vmalloc=<size> to increase size.
[   18.509004] wlan: [1165:I:ANY] =======ol_if_register_wifi3_0==========
[   18.509004]
[   18.510546] wlan: [1165:I:ANY] osif_nss_register_module: 708: NSS wifi ops registered for target_type:1 with soc_ops:c9cbbaf0
[   18.518313] wlan: [1165:I:ANY] ol_ath_wifi_ssr: 298: ol_ath_wifi_ssr: SSR event 2 bus_type 1
[   18.529806] remoteproc remoteproc0: powering up cd00000.qcom_q6v5_wcss
[   18.550934] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668
[   19.437005] Subsystem error monitoring/handling services are up
[   19.437284] remoteproc remoteproc0: remote processor cd00000.qcom_q6v5_wcss is now up
[   19.441894] rpmsg_dev_probe: No pm domain
[   19.449919] rpmsg_dev_probe: No pm domain
[   19.453800] wlan: [1165:I:ANY] ol_ath_wifi_ssr: 298: ol_ath_wifi_ssr: SSR event 3 bus_type 1
[   19.457886] cnss[2]: INFO: Waiting for FW ready. Device: 0xfffe, FW ready timeout: 15 seconds
[   19.466519] cnss[2]: INFO: QMI WLFW service connected, state: 0x1
[   19.466813] diag: In diag_send_feature_mask_update, control channel is not open, p: 2, 7f79dbc4
[   19.480914] cnss[2]: INFO: device_id : 65534 mem mode : [0]
[   19.489243] cnss[2]: INFO: platform name: Qualcomm Technologies, Inc. IPQ807x/AP-HK07
[   19.495397] cnss[2]: INFO: Target capability: chip_id: 0x0, chip_family: 0x0, board_id: 0xff, soc_id: 0xffffffff, fw_version: 0x230404a5, fw_build_timestamp: 2021-06-08 04:20, otp_version: 0x0 eeprom_caldata_read_timeout 0s
[   19.502786] cnss[2]: INFO: Boardid from dts:290,FW:ff
[   19.526724] cnss[2]: INFO: BDF location : 0x4b0c0000
[   19.527578] cnss[2]: INFO: BDF IPQ8074/bdwlan.b290 size 131072
[   19.533156] cnss[2]: INFO: per device BDF location : 0x4b0e0000
[   19.538368] cnss[2]: INFO: CALDATA IPQ8074/caldata.bin size 131072 offset 0x20000
[   19.574596] cnss[2]: INFO: FW ready received for device 0xfffe
[   19.574839] wlan: [1165:I:ANY] pld_ahb_wlan_enable: 705: cnss_mode: Mission mode
[   19.579516] cnss[2]: INFO: Sending mode message, mode: MISSION(0), state: 0x7
[   19.596554] wlan: [1165:I:ANY] qca_napi_create: 373: qca_napi_create: napi instance 0 created on pipe 4
[   19.596709] wlan: [1165:I:ANY] __ol_ath_attach: 4044: Allocated soc b8680540
[   19.611839] wlan: [1165:I:ANY] osif_nss_wifi_soc_setup: 827: nss register id -1 nss config 0 Target Type 18
[   19.612051] wlan: [1165:I:ANY] __ol_ath_attach: 4248: dev name soc0
[   19.622236] wlan: [1165:I:ANY] ol_ath_soc_attach: 6558: WMI attached. wmi_handle b867fc00
[   19.643946] wlan: [1165:I:ANY] htc_wmi_init: 5597: HT Create . b5f58000
[   19.643978] wlan: [1165:I:ANY] htc_wmi_init: 5604: Skipping BMI Done
[   19.649485] wlan: [1165:I:ANY] htc_wmi_init: 5661: host_enable 0 nss_nwifi_offload 0
[   19.676982] wlan: [1165:I:ANY] ol_target_init_complete: 5732: CDP soc attach success
[   19.677015] wlan: [1165:I:ANY] ol_target_init_complete: 5739: Soc attach success NSS config 0
[   19.683939] wlan: [1165:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle b5f58000, ep 2, value 1
[   19.692322] wlan: [1165:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle b5f58000, ep 3, value 1
[   19.692344] wlan: [1159:E:ANY] send_filled_buffers_to_user: Send Failed -3 drop_count = 1
[   19.712161] wlan: [1150:I:TIF] HE_CAP Info = 1a08010d
[   19.719759] wlan: [1150:I:TIF] Num HW modes = 1
[   19.724804] wlan: [1150:I:TIF] Num PHY = 2
[   19.729113] wlan: [1150:I:TIF] FW Build Version (Ext.) = 0
[   19.733277] wlan: [1150:I:TIF] HDL Version: MajorVersion.MinorVersion = 0.0
[   19.738757] wlan: [1150:I:TIF] Preferred HW Mode = 1 Num Radios = 2
[   19.745669] wlan: [1150:I:TIF] init_deinit_add_11ax_modes: 2429: hw_mode_id = 1 phy_id = 0 wireless modes = f97f9001
[   19.751868] wlan: [1150:I:TIF] init_deinit_add_11ax_modes: 2429: hw_mode_id = 1 phy_id = 1 wireless modes = 680688c
[   19.762932] wlan: [1150:I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notification: 431: dfs_offload 1
[   19.772889] wlan: [1150:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_agile_soc_obj_init: 3417: dfs->dfs_psoc_idx: 0
[   19.783290] wlan: [1150:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_agile_soc_obj_init: 3423: dfs_soc_obj->num_dfs_privs: 1
[   19.793422] wlan: [1150:I:TIF] init_deinit_alloc_pdevs: 1550: CDP PDEV ATTACH success
[   19.803199] wlan: [1150:E:QDF] SOC0_PDEV2161124296 creation failed
[   19.810981] wlan: [1150:E:DIRECT_BUF_RX] target_if_direct_buf_pdev_debugfs_init: 325: error while creating direct_buf debugfs dir
[   19.817103] wlan: [1150:I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notification: 403: Do not allocate DFS object for 2G, pdev_id = 1
[   19.829560] wlan: [1150:I:TIF] init_deinit_alloc_pdevs: 1550: CDP PDEV ATTACH success
[   19.841810] wlan: [1150:I:TIF] init_deinit_get_total_num_ema_vaps: 238: num_radios: 2
[   19.849640] wlan: [1150:I:TIF] init_deinit_get_total_num_ema_vaps: 256: ema_max_vap_cnt: 0
[   19.857430] wlan: [1150:I:TIF] init_deinit_get_total_num_vdevs_for_soc: 376: num_vdevs: 34
[   19.865646] wlan: [1150:I:TIF] init_deinit_get_total_num_ema_vaps: 238: num_radios: 2
[   19.873851] wlan: [1150:I:TIF] init_deinit_get_total_num_ema_vaps: 256: ema_max_vap_cnt: 0
[   19.881780] wlan: [1150:I:TIF] init_deinit_get_total_num_vdevs_for_soc: 376: num_vdevs: 34
[   19.889890] wlan: [1150:I:TIF] init_deinit_get_total_beaconing_vdevs_for_soc: 598: beacon_tx_offload_max_vdev: 32
[   19.898166] wlan: [1150:I:TIF] init_deinit_get_total_num_ema_vaps: 238: num_radios: 2
[   19.908467] wlan: [1150:I:TIF] init_deinit_get_total_num_ema_vaps: 256: ema_max_vap_cnt: 0
[   19.916280] wlan: [1150:I:TIF] init_deinit_get_total_num_vdevs_for_soc: 376: num_vdevs: 34
[   19.924459] wlan: [1150:I:TIF] init_deinit_get_total_num_ema_vaps: 238: num_radios: 1
[   19.932686] wlan: [1150:I:TIF] init_deinit_get_total_num_ema_vaps: 256: ema_max_vap_cnt: 0
[   19.940588] wlan: [1150:I:TIF] init_deinit_get_total_num_vdevs_for_soc: 376: num_vdevs: 17
[   19.948817] wlan: [1150:I:ANY] init_deinit_update_pdev_tgt_info: 1924: pdev id:0 wmi_handle:b867fc00
[   19.966389] wlan: [1150:I:ANY] init_deinit_update_pdev_tgt_info: 1995: Pdev = 0 Number of peers = 529 vdevs = 17
[   19.966431] wlan: [1150:I:TIF] init_deinit_update_pdev_tgt_info: 1998: CDP PDEV INIT success
[   19.976691] wlan: [1150:I:ANY] init_deinit_update_pdev_tgt_info: 1924: pdev id:1 wmi_handle:b54d1800
[   19.994220] wlan: [1150:I:ANY] init_deinit_update_pdev_tgt_info: 1995: Pdev = 1 Number of peers = 529 vdevs = 17
[   19.994269] wlan: [1150:I:TIF] init_deinit_update_pdev_tgt_info: 1998: CDP PDEV INIT success
[   20.104989] wlan: [1150:I:ANY] copy_fw_abi_version_tlv: 7216: copy_fw_abi_version_tlv: INIT_CMD version: 1, 0, 0x5f414351, 0x4c4d, 0x0, 0x0
[   20.308316] wlan: [1150:I:ANY] ready_extract_init_status_tlv: 9738: ready_extract_init_status_tlv:0
[   20.308349] wlan: [1150:I:ANY] dp_peer_map_attach_wifi3: 9617: dp_peer_map_attach_wifi3 max_peers 1109, max_ast_index: 4112
[   20.308349]
[   20.316367] wlan: [1165:I:ANY] ol_ath_connect_htc: 1256: WMI is ready
[   20.329229] wlan: [1165:I:ANY] ol_ath_soc_attach: 6686: connect HTC
[   20.335390] wlan: [1165:I:ANY] ol_ath_soc_attach: 6687: bypasswmi : 0
[   20.341452] wlan: [1165:I:ANY] ol_ath_soc_attach: 6761: UMAC attach
[   20.348129] wlan: [1165:I:ANY] __ol_ath_attach: 4371: ======before swapped======
[   20.348129]
[   20.354168] wlan: [1165:I:ANY] __ol_ath_attach: 4374: ======set 1st radio as wifi1======
[   20.354168]
[   20.363153] wlan: [1165:I:ANY] __ol_ath_attach: 4382: ========after swapped=======
[   20.363153]
[   20.372778] wlan: [1165:I:ANY] __ol_ath_attach: 4384: pdev_netdev name wifi1
[   20.381557] wlan: [1165:I:ANY] __ol_ath_attach: 4433: Skip txrx_pdev_attach_target
[   20.388836] wlan: [1165:I:ANY] __ol_ath_attach: 4459: BURSTING enabled by default
[   20.396309] wlan: [1165:I:ANY] ol_ath_pdev_attach: 8769: interface_id 1
[   20.403781] wlan: [1165:I:TIF] ol_ath_pdev_regdmn_init: 6922:  phy id = 0 Modes supported
[   20.410193] wlan: [1165:I:TIF] ol_ath_pdev_regdmn_init: 6929:  11b = 0 11g = 0 11a = 1 11n = 1 11ac = 1 11ax = 1
[   20.418541] wlan: [1165:I:TIF] ol_ath_pdev_regdmn_init: 6938:  Reg cap - phy_id = 0 supp_bnd = 2, modes = 793f9001, lo_2g = 0, hi_2g = 0 lo_g5 = 4900, hi_5g = 5920
[   20.428810] wlan: [1165:I:ANY] ol_ath_update_wireless_modes: 1331: wireless_modes = 793f9001 before update
[   20.443158] wlan: [1165:I:ANY] ol_ath_update_wireless_modes: 1347: Wireless_modes = 793f9001 after update
[   20.452842] wlan: [1165:I:ANY] ol_ath_update_ext_caps: 1939: 11ax 5G supported case
[   20.462582] wlan: [1165:I:MBSSIE] ieee80211_mbss_attach: 220: :>
[   20.469942] wlan: [1165:I:MBSSIE] ieee80211_mbss_attach: 233: :<
[   20.476184] wlan: [1165:I:ANY] ol_resmgr_create: 223: OL Resmgr Init-ed
[   20.482298] wlan: [1165:I:ANY] acfg_attach: 3339: acfg_attach: 3339: Netlink socket created:b825f400
[   20.488542] wlan: [1165:I:ANY] ol_ath_stats_attach: 2316: periodic_chan_stats: 1
[   20.498535] wlan: [1165:I:ANY] wlan_scan_update_channel_list: 1141: num_chan: 22
[   20.505283] wlan: [0:I:ANY] ol_ath_pdev_attach: 9085: Set global_ic[1], ptr:c78a59b4
[   20.512610] wlan: [0:I:RPTR] qca_multi_link_init_module: 245:
[   20.512610] ******QCA Repeater Initialization Done***********
[   20.512610]
[   20.520346] wlan: [0:I:ANY] dp_lag_soc_enable: 102: pdev(b54d1604) Enabling DBDC Repeater 0
[   20.533410] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: 55: pdev(b54d1604) is_primary 0
[   20.541997] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_handler: 50: twt enabled
[   20.551647] wlan: [1165:I:ANY] ol_ath_ucfg_set_rx_pkt_protocol_tagging: 2197: Set RX packet type TAG, opcode : 0, pkt_type : 18, metadata : 0xca0,pdev_id = 0, REO dest ring = 5
[   20.551647]
[   20.557908] wlan: [1165:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 612: cfg block channel list is empty
[   20.575111] wlan: [1165:I:ANY] ol_ath_configure_cong_ctrl_max_msdus: 3942: pdev_idx = 0 tx_desc_limit = 32768
[   20.584625] wlan: [1165:I:ANY] osif_wrap_attach: 239: osif wrap attached
[   20.584625]
[   20.594495] wlan: [1165:I:ANY] osif_wrap_devt_init: 201: osif wrap dev table init done
[   20.594495]
[   20.602726] wlan: [1165:I:ANY] osif_wrap_attach: 247:  Wrap Attached: Wrap_com =b1e30600 ic->ic_wrap_com=b1e30600 &wrap_com->wc_devt=b1e30600
[   20.602726]
[   20.611949] wlan: [1165:I:ANY] __ol_ath_attach: 4632: needed_headroom reservation 60
[   20.626304] wlan: [1165:I:ANY] ieee80211_cfg80211_radio_attach: 13330: ic: 0xb5500540, wdev: 0xb5517d60, wiphy: 0xb50b7160, netdev: 0xb5500000
[   20.634662] wlan: [1165:I:ANY] __ol_ath_attach: 4371: ======before swapped======
[   20.634662]
[   20.646796] wlan: [1165:I:ANY] __ol_ath_attach: 4378: ======set 2nd radio as wifi0======
[   20.646796]
[   20.655750] wlan: [1165:I:ANY] __ol_ath_attach: 4382: ========after swapped=======
[   20.655750]
[   20.665291] wlan: [1165:I:ANY] __ol_ath_attach: 4384: pdev_netdev name wifi0
[   20.674152] wlan: [1165:I:ANY] __ol_ath_attach: 4433: Skip txrx_pdev_attach_target
[   20.681389] wlan: [1165:I:ANY] __ol_ath_attach: 4459: BURSTING enabled by default
[   20.688833] wlan: [1165:I:ANY] ol_ath_pdev_attach: 8769: interface_id 0
[   20.696442] wlan: [1165:I:TIF] ol_ath_pdev_regdmn_init: 6922:  phy id = 1 Modes supported
[   20.702731] wlan: [1165:I:TIF] ol_ath_pdev_regdmn_init: 6929:  11b = 1 11g = 1 11a = 0 11n = 1 11ac = 1 11ax = 1
[   20.711078] wlan: [1165:I:TIF] ol_ath_pdev_regdmn_init: 6938:  Reg cap - phy_id = 1 supp_bnd = 1, modes = 680680c, lo_2g = 2312, hi_2g = 2732 lo_g5 = 0, hi_5g = 0
[   20.721418] wlan: [1165:I:ANY] ol_ath_update_wireless_modes: 1331: wireless_modes = 680680c before update
[   20.735649] wlan: [1165:I:ANY] ol_ath_update_wireless_modes: 1347: Wireless_modes = 680680c after update
[   20.745288] wlan: [1165:I:ANY] ol_ath_update_ext_caps: 1947: 11ax 2G supported case
[   20.754957] wlan: [1165:I:MBSSIE] ieee80211_mbss_attach: 220: :>
[   20.762191] wlan: [1165:I:MBSSIE] ieee80211_mbss_attach: 233: :<
[   20.768456] wlan: [1165:I:ANY] ol_resmgr_create: 223: OL Resmgr Init-ed
[   20.774647] wlan: [1165:I:ANY] acfg_attach: 3314: Offload using existing sock b825f400
[   20.780775] wlan: [1165:I:ANY] ol_ath_stats_attach: 2316: periodic_chan_stats: 1
[   20.788949] wlan: [1165:I:ANY] wlan_scan_update_channel_list: 1141: num_chan: 11
[   20.796367] wlan: [0:I:ANY] ol_ath_pdev_attach: 9085: Set global_ic[2], ptr:c78a59b4
[   20.803673] wlan: [0:I:ANY] dp_lag_soc_enable: 102: pdev(b54d1e04) Enabling DBDC Repeater 0
[   20.811430] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: 55: pdev(b54d1e04) is_primary 0
[   20.820038] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_handler: 50: twt enabled
[   20.829821] wlan: [1165:I:ANY] ol_ath_ucfg_set_rx_pkt_protocol_tagging: 2197: Set RX packet type TAG, opcode : 0, pkt_type : 18, metadata : 0xca0,pdev_id = 1, REO dest ring = 5
[   20.829821]
[   20.835949] wlan: [1165:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 612: cfg block channel list is empty
[   20.853143] wlan: [1165:I:ANY] ol_ath_configure_cong_ctrl_max_msdus: 3942: pdev_idx = 1 tx_desc_limit = 32768
[   20.862722] wlan: [1165:I:ANY] osif_wrap_attach: 239: osif wrap attached
[   20.862722]
[   20.872559] wlan: [1165:I:ANY] osif_wrap_devt_init: 201: osif wrap dev table init done
[   20.872559]
[   20.880699] wlan: [1165:I:ANY] osif_wrap_attach: 247:  Wrap Attached: Wrap_com =b1e31e00 ic->ic_wrap_com=b1e31e00 &wrap_com->wc_devt=b1e31e00
[   20.880699]
[   20.889917] wlan: [1165:I:ANY] __ol_ath_attach: 4632: needed_headroom reservation 60
[   20.904178] wlan: [1165:I:ANY] wlan_cfg80211_init: 13147: Number of 2G channels: 11
[   20.912271] wlan: [1165:I:ANY] ieee80211_cfg80211_radio_attach: 13330: ic: 0xb5640540, wdev: 0xb5657d60, wiphy: 0xb1b59160, netdev: 0xb5640000
[   20.920394] wlan: [1165:I:Dynamic Mode Change] ol_ath_check_and_reconfig_hw_mode: 3911: Running with HW mode = 1
[   20.932931] wlan: [1165:E:QLD] qld_register: 108: Handle or address is NULL
[   20.943127] wlan: [1165:I:ANY] wlan_pdev_operation: 802: num_radios=1, wifi_radios[0].sc = b5500540_radio_type = 2
[   20.949655] wlan: [1165:I:ANY] wlan_pdev_operation: 802: num_radios=2, wifi_radios[1].sc = b5640540_radio_type = 2
[   20.960063] wlan: [1165:I:ANY] init_ath_pci_3_0: 183: 6ath_ol_pci_wifi3.0 :  (Atheros/multi-bss)
[   21.022100] wlan: [1201:I:ANY] osif_nss_register_module: 708: NSS wifi ops registered for target_type:0 with soc_ops:7fdf2010
[   21.022406] wlan: [1201:I:ANY] init_ath_pci_2_0: 147: 6ath_ol_pci_2_0:  (Atheros/multi-bss)
acfg_tool: Issuing blocking call to wait for events
[   23.392882] vmap allocation for size 888832 failed: use vmalloc=<size> to increase size.
[   23.410837] ECM init
[   23.410887] ECM database jhash random seed: 0x58b9db60
[   23.412871] ECM init complete
[   23.569615] device eth0 entered promiscuous mode
[   23.570854] br-lan: port 1(eth0) entered forwarding state
[   23.573367] br-lan: port 1(eth0) entered forwarding state
[   24.564634] br-lan: port 1(eth0) entered disabled state
[   27.664639] nss-dp 3a001a00.dp6 eth0: PHY Link up speed: 1000
[   27.664710] br-lan: port 1(eth0) entered forwarding state
[   27.669382] br-lan: port 1(eth0) entered forwarding state
[   29.664610] br-lan: port 1(eth0) entered forwarding state
[   39.396435] mc_attach: enabled snooping on br-lan.
4

Well, this device seems to work out of the gate with the WAX218 builds. The root file system lives on mtd19, if you're using the ubiformat method.

LED layout does need some work, as the WAX620 has more less, and they're in a different order than the WAX218. Will get that together as a PR here shortly.

1 Like