@bobafetthotmail
During upgrade between version:
Linux version 4.4.42 (gcc version 5.4.0 (LEDE GCC 5.4.0 r3114-1a83d4d) ) #0 Tue Jan 24 19:33:45 2017
to
Linux version 4.4.49 (gcc version 5.4.0 (LEDE GCC 5.4.0 r3410-6c61676) ) #0 Fri Feb 17 13:42:13 2017
kernel modules are not loaded.
console log (over serial):
Watchdog handover: fd=3
-
watchdog -
killall: telnetd: no process killed
Sending TERM to remaining processes ... sysupgrade ubus ubusd logd rpcd portmap netifd hd-idle minidlna uhttpd smbd nmbd ntpd rpc.statd rpc.mountd watchcat.sh watchcat.sh sleep sleep
Sending KILL to remaining processes ... watchcat.sh watchcat.sh sleep sleep
Switching to ramdisk...
[685285.929386] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" stops
[685285.958563] UBIFS (ubi0:2): un-mount UBI device 0
removing ubiblock0_1
[685287.274760] block ubiblock0_1: released
Volume ID 0, size 16 LEBs (2064384 bytes, 2.0 MiB), LEB size 129024 bytes (126.0 KiB), dynamic, name "kernel", alignment 1
Volume ID 1, size 120 LEBs (15482880 bytes, 14.8 MiB), LEB size 129024 bytes (126.0 KiB), dynamic, name "rootfs", alignment 1
Set volume size to 110186496
Volume ID 2, size 854 LEBs (110186496 bytes, 105.1 MiB), LEB size 129024 bytes (126.0 KiB), dynamic, name "rootfs_data", alignment 1
[685294.199422] UBIFS (ubi0:2): default file-system created
[685294.231401] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 10485
[685294.293625] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[685294.301710] UBIFS (ubi0:2): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[685294.311778] UBIFS (ubi0:2): FS size: 108767232 bytes (103 MiB, 843 LEBs), journal size 5419008 bytes (5 MiB, 42 LEBs)
[685294.322530] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB)
[685294.329276] UBIFS (ubi0:2): media format: w4/r0 (latest is w4/r0), UUID 06932663-A520-4179-9A3D-C18095FE0C1F, small LPT model
[685294.360728] UBIFS (ubi0:2): un-mount UBI device 0
[685294.365562] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" stops
sysupgrade successful
umount: can't unmount /dev: Resource busy
umount: can't unmount /tmp: Resource busy
[685294.393348] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[685294.416970] reboot: Restarting systemU-Boot 2016.05-tld-1 (Jun 12 2016 - 13:59:20 -0700)
ZyXEL NSA310 1-Bay Power Media ServerSoC: Kirkwood 88F6281_A1
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
PHY reset timed out
MV88E1318 PHY initialized on egiga0
Hit any key to stop autoboot: 10 9 8 7 6 5 4 3 2 1 0Error: "scan_disk" not defined
Error: "bootcmd_linux" not defined
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=2", size 126 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
ubi0: VID header offset: 512 (aligned 512), data offset: 2048
ubi0: good PEBs: 1007, bad PEBs: 7, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 833779665
ubi0: available PEBs: 0, total reserved PEBs: 1007, PEBs reserved for bad PEB handling: 13
Read 0 bytes from volume kernel to 800000
No size specified -> Using max size (2064384)Booting kernel from Legacy Image at 00800000 ...
Image Name: ARM LEDE Linux-4.4.49 Created: 2017-02-17 13:42:13 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1952178 Bytes = 1.9 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.49 (kofec@E5420Mint) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3410-6c61676) ) #0 Fri Feb 17 13:42:13 2017
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine model: ZyXEL NSA310b
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 253784K/262144K available (3978K kernel code, 138K rwdata, 1484K rodata, 168K init, 196K bss, 8360K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc055ddb4 (5464 kB)
[ 0.000000] .init : 0xc055e000 - 0xc0588000 ( 168 kB)
[ 0.000000] .data : 0xc0588000 - 0xc05aa808 ( 139 kB)
[ 0.000000] .bss : 0xc05aa808 - 0xc05dbb64 ( 197 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000009] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.000090] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[ 0.090083] pid_max: default: 32768 minimum: 301
[ 0.090193] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090212] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090744] CPU: Testing write buffer coherency: ok
[ 0.091108] Setting up static identity map for 0x81e0 - 0x821c
[ 0.091425] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[ 0.096474] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.096631] pinctrl core: initialized pinctrl subsystem
[ 0.097734] NET: Registered protocol family 16
[ 0.098080] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.098983] cpuidle: using governor ladder
[ 0.099333] Feroceon L2: Enabling L2
[ 0.099377] Feroceon L2: Cache support initialised.
[ 0.117502] SCSI subsystem initialized
[ 0.118259] usbcore: registered new interface driver usbfs
[ 0.118335] usbcore: registered new interface driver hub
[ 0.118395] usbcore: registered new device driver usb
[ 0.119320] clocksource: Switched to clocksource orion_clocksource
[ 0.120436] NET: Registered protocol family 2
[ 0.120969] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.121005] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.121034] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.121086] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.121112] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.121262] NET: Registered protocol family 1
[ 0.123044] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.123118] Crashlog allocated RAM at address 0x3f00000
[ 0.136131] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.136155] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.138823] io scheduler noop registered
[ 0.138841] io scheduler deadline registered (default)
[ 0.140080] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 0.140669] irq: Cannot allocate irq_descs @ IRQ33, assuming pre-allocated
[ 0.141018] irq: Cannot allocate irq_descs @ IRQ65, assuming pre-allocated
[ 0.141583] mvebu-pcie mbus:pcie-controller: PCI host bridge to bus 0000:00
[ 0.141601] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
[ 0.141612] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[ 0.141626] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.141910] PCI: bus0: Fast back to back transfers disabled
[ 0.141925] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.142444] PCI: bus1: Fast back to back transfers disabled
[ 0.142542] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe00fffff]
[ 0.142557] pci 0000:00:01.0: BAR 7: assigned [io 0x10000-0x10fff]
[ 0.142575] pci 0000:01:00.0: BAR 6: assigned [mem 0xe0000000-0xe000ffff pref]
[ 0.142590] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0010000-0xe0013fff 64bit pref]
[ 0.142612] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0014000-0xe0014fff 64bit pref]
[ 0.142631] pci 0000:01:00.0: BAR 0: assigned [io 0x10000-0x100ff]
[ 0.142645] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.142656] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff]
[ 0.142669] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff]
[ 0.173165] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.174197] console [ttyS0] disabled
[ 0.174271] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A
[ 0.708835] console [ttyS0] enabled
[ 0.713530] sata_mv f1080000.sata: slots 32 ports 2
[ 0.721658] scsi host0: sata_mv
[ 0.725567] scsi host1: sata_mv
[ 0.728929] ata1: SATA max UDMA/133 irq 32
[ 0.733081] ata2: SATA max UDMA/133 irq 32
[ 0.737809] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
[ 0.744217] nand: Samsung NAND 128MiB 3,3V 8-bit
[ 0.748858] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.756482] Scanning device for bad blocks
[ 0.793935] Bad eraseblock 348 at 0x000002b80000
[ 0.799189] Bad eraseblock 355 at 0x000002c60000
[ 0.834959] Bad eraseblock 681 at 0x000005520000
[ 0.841472] Bad eraseblock 701 at 0x0000057a0000
[ 0.854288] Bad eraseblock 787 at 0x000006260000
[ 0.872269] Bad eraseblock 927 at 0x0000073e0000
[ 0.883084] Bad eraseblock 992 at 0x000007c00000
[ 0.890717] 3 ofpart partitions found on MTD device orion_nand
[ 0.896573] Creating 3 MTD partitions on "orion_nand":
[ 0.901755] 0x000000000000-0x0000000c0000 : "uboot"
[ 0.908165] 0x0000000c0000-0x000000140000 : "uboot_env"
[ 0.914518] 0x000000140000-0x000008000000 : "ubi"
[ 0.921152] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.927718] ehci-pci: EHCI PCI platform driver
[ 0.932277] ehci-orion: EHCI orion driver
[ 0.936466] orion-ehci f1050000.ehci: EHCI Host Controller
[ 0.942028] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 0.949860] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000
[ 0.969337] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 0.976047] hub 1-0:1.0: USB hub found
[ 0.980017] hub 1-0:1.0: 1 port detected
[ 0.984420] usbcore: registered new interface driver usb-storage
[ 0.990908] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0
[ 0.997863] i2c /dev entries driver
[ 1.002666] orion_wdt: Initial timeout 21 sec
[ 1.012400] marvell-cesa f1030000.crypto: CESA device successfully registered
[ 1.020670] NET: Registered protocol family 10
[ 1.026522] NET: Registered protocol family 17
[ 1.031083] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.043775] 8021q: 802.1Q VLAN Support v1.8
[ 1.050329] UBI: auto-attach mtd2
[ 1.053498] ubi0: attaching mtd2
[ 1.273013] ubi0: scanning is finished
[ 1.288336] ubi0: attached mtd2 (name "ubi", size 126 MiB)
[ 1.293881] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[ 1.300807] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[ 1.307538] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
[ 1.314370] ubi0: good PEBs: 1007, bad PEBs: 7, corrupted PEBs: 0
[ 1.320502] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 1.327752] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 833779665
[ 1.336851] ubi0: available PEBs: 0, total reserved PEBs: 1007, PEBs reserved for bad PEB handling: 13
[ 1.346519] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 1.353347] ubi0: background thread "ubi_bgt0d" started, PID 900
[ 1.360143] block ubiblock0_1: created from ubi0:1(rootfs)
[ 1.365658] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 1.372925] rtc-mv f1010300.rtc: setting system clock to 2017-02-21 18:27:20 UTC (1487701640)
[ 1.409351] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 1.429445] ata1.00: ATA-8: HGST HTS545050A7E680, GG2OAH10, max UDMA/100
[ 1.436179] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.479456] ata1.00: configured for UDMA/100
[ 1.484169] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AH10 PQ: 0 ANSI: 5
[ 1.493364] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[ 1.500915] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 1.506711] sd 0:0:0:0: [sda] Write Protect is off
[ 1.511714] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.523145] hub 1-1:1.0: USB hub found
[ 1.527248] hub 1-1:1.0: 4 ports detected
[ 1.583751] sda: sda1
[ 1.587187] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.809334] usb 1-1.2: new high-speed USB device number 3 using orion-ehci
[ 1.839343] ata2: SATA link down (SStatus 0 SControl F300)
[ 1.850145] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 1.857831] Freeing unused kernel memory: 168K (c055e000 - c0588000)
[ 2.009126] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 2.029849] scsi host2: usb-storage 1-1.2:1.0
[ 2.441801] init: Console is alive
[ 2.445360] init: - watchdog -
[ 2.560463] init: - preinit -
[ 3.014895] random: jshn: uninitialized urandom read (4 bytes read, 14 bits of entropy available)
[ 3.090580] random: jshn: uninitialized urandom read (4 bytes read, 14 bits of entropy available)
/bin/board_detect: /etc/board.d/02_network: line 1: mtd_get_mac_ascii: not found[ 3.123992] random: jshn: uninitialized urandom read (4 bytes read, 14 bits of entropy available)[ 3.158267] random: jshn: uninitialized urandom read (4 bytes read, 14 bits of entropy available)
[ 3.186138] random: jshn: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 3.195351] scsi 2:0:0:0: Direct-Access SMI USB DISK 1100 PQ: 0 ANSI: 4
[ 3.206515] random: procd: uninitialized urandom read (4 bytes read, 15 bits of entropy available)
[ 3.216554] sd 2:0:0:0: [sdb] 7866368 512-byte logical blocks: (4.03 GB/3.75 GiB)
[ 3.237507] sd 2:0:0:0: [sdb] Write Protect is off
[ 3.243194] sd 2:0:0:0: [sdb] No Caching mode page found
[ 3.248537] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 3.272574] sdb: sdb1
[ 3.278806] sd 2:0:0:0: [sdb] Attached SCSI removable disk
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.423149] mount_root: loading kmods from internal overlay
Segmentation fau[ 5.435046] mount_root: failed to launch kmodloader from internal overlay
lt
[ 6.349724] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 994
[ 6.460124] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 6.467994] UBIFS (ubi0:2): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 6.477981] UBIFS (ubi0:2): FS size: 108767232 bytes (103 MiB, 843 LEBs), journal size 5419008 bytes (5 MiB, 42 LEBs)
[ 6.488644] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB)
[ 6.495308] UBIFS (ubi0:2): media format: w4/r0 (latest is w4/r0), UUID 06932663-A520-4179-9A3D-C18095FE0C1F, small LPT model
[ 6.507093] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 6.514237] block: unable to load configuration (fstab: Entry not found)
[ 6.521042] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 6.527603] block: unable to load configuration (fstab: Entry not found)
[ 6.534399] block: attempting to load /etc/config/fstab
[ 6.542758] block: unable to load configuration (fstab: Entry not found)
[ 6.549580] block: no usable configuration
[ 6.558875] UBIFS (ubi0:2): un-mount UBI device 0
[ 6.563645] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" stops
[ 6.599845] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 996
[ 6.710343] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 6.718214] UBIFS (ubi0:2): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 6.728201] UBIFS (ubi0:2): FS size: 108767232 bytes (103 MiB, 843 LEBs), journal size 5419008 bytes (5 MiB, 42 LEBs)
[ 6.738865] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB)
[ 6.745523] UBIFS (ubi0:2): media format: w4/r0 (latest is w4/r0), UUID 06932663-A520-4179-9A3D-C18095FE0C1F, small LPT model
[ 7.422090] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 7.429215] block: unable to load configuration (fstab: Entry not found)
[ 7.436040] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 7.442624] block: unable to load configuration (fstab: Entry not found)
[ 7.449557] block: attempting to load /etc/config/fstab
[ 7.454900] block: unable to load configuration (fstab: Entry not found)
[ 7.461696] block: no usable configuration
[ 7.466509] mount_root: overlay filesystem has not been fully initialized yet
[ 7.474787] mount_root: switching to ubifs overlay- config restore -
[ 7.564701] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 7.627362] procd: - early -
[ 7.630757] procd: - watchdog -
[ 8.090705] random: jshn: uninitialized urandom read (4 bytes read, 68 bits of entropy available)
[ 8.180194] random: jshn: uninitialized urandom read (4 bytes read, 68 bits of entropy available)
[ 8.268516] random: jshn: uninitialized urandom read (4 bytes read, 68 bits of entropy available)
[ 8.546828] procd: - ubus -
[ 8.644681] random: ubusd: uninitialized urandom read (4 bytes read, 92 bits of entropy available)
[ 8.707991] procd: - init -
Please press Enter to activate this console.
[ 9.203134] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts:
[ 9.366161] random: nonblocking pool is initialized
BusyBox v1.26.2 () built-in shell (ash)
_________ / /\ _ ___ ___ ___ / LE / \ | | | __| \| __| / DE / \ | |__| _|| |) | _|
/___/ LE \ |||/|| lede-project.org
\ \ DE /
\ LE \ / -----------------------------------------------------------
\ DE \ / Reboot (SNAPSHOT, r3521-7df998b)
________/ -----------------------------------------------------------root@LEDEnsa310:/# ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN qlen 1
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
root@LEDEnsa310:/# insmod mii
root@LEDEnsa310:/lib/modules/4.4.49# insmod r8169.ko
[ 685.528153] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 685.533845] pci 0000:00:01.0: enabling device (0140 -> 0143)
[ 685.539572] r8169 0000:01:00.0: enabling device (0140 -> 0143)
[ 685.546452] r8169 0000:01:00.0 eth0: RTL8168d/8111d at 0xd095e000, 00:00:00:00:00:30, XID 083000c0 IRQ 83
[ 685.556107] r8169 0000:01:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
root@LEDEnsa310:/lib/modules/4.4.49# [ 685.890228] r8169 0000:01:00.0 eth0: link down
[ 685.894999] r8169 0000:01:00.0 eth0: link down
[ 685.915235] device eth0 entered promiscuous mode
[ 685.931303] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 688.567495] r8169 0000:01:00.0 eth0: link up
[ 688.572588] br-lan: port 1(eth0) entered forwarding state
[ 688.578046] br-lan: port 1(eth0) entered forwarding state
[ 688.584461] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 690.569331] br-lan: port 1(eth0) entered forwarding state
root@LEDEnsa310:/lib/modules/4.4.49# ip adrdr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN qlen 1
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel master br-lan state UP qlen 1000
link/ether 00:00:00:00:00:30 brd ff:ff:ff:ff:ff:ff
3: br-lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP qlen 1000
link/ether 50:67:f0:69:4e:a5 brd ff:ff:ff:ff:ff:ff
inet 192.168.1.31/24 brd 192.168.1.255 scope global br-lan
valid_lft forever preferred_lft forever
inet6 fe80::5267:f0ff:fe69:4ea5/64 scope link
valid_lft forever preferred_lft forever
root@LEDEnsa310:/lib/modules/4.4.49#[details=Summary] - config restore -
This text will be hidden
[/details]