No internet on Wifi Client Mode

vlad.rusin.poltava · February 1, 2023, 5:44pm

Hi.
I can not set up the Internet acsess:
LTE Internet ----> MIFI LTE ROUTER ----> OPEN WRT (wifi client) ----> LOCAL ----> this PC

MIFI LTE ROUTER: 192.168.11.1
OPEN WRT: 192.168.1.1

LOCAL TO OPEN WRT - access deny
LOCAL TO MIFI LTE ROUTER - access deny
LOCAL TO INTERNET - access fail
Ping in LUCI:

PING openwrt.org (139.59.209.225): 56 data bytes

--- openwrt.org ping statistics ---
5 packets transmitted, 0 packets received, 100% packet loss

frollic · February 1, 2023, 5:48pm

in which firewall zone is the wifi client connection, on the openwrt router ?

vlad.rusin.poltava · February 1, 2023, 7:05pm

config defaults
        option input 'ACCEPT'
        option output 'ACCEPT'
        option forward 'REJECT'

config zone
        option name 'lan'
        option input 'ACCEPT'
        option output 'ACCEPT'
        option forward 'ACCEPT'
        list network 'lan'

config zone
        option name 'wan'
        option input 'REJECT'
        option output 'ACCEPT'
        option forward 'REJECT'
        option masq '1'
        option mtu_fix '1'
        list network 'wan'
        list network 'wan6'
        list network 'wwan'

config forwarding
        option src 'lan'
        option dest 'wan'

config rule
        option name 'Allow-DHCP-Renew'
        option src 'wan'
        option proto 'udp'
        option dest_port '68'
        option target 'ACCEPT'
        option family 'ipv4'

config rule
        option name 'Allow-Ping'
        option src 'wan'
        option proto 'icmp'
        option icmp_type 'echo-request'
        option family 'ipv4'
        option target 'ACCEPT'

config rule
        option name 'Allow-IGMP'
        option src 'wan'
        option proto 'igmp'
        option family 'ipv4'
        option target 'ACCEPT'

config rule
        option name 'Allow-DHCPv6'
        option src 'wan'
        option proto 'udp'
        option dest_port '546'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-MLD'
        option src 'wan'
        option proto 'icmp'
        option src_ip 'fe80::/10'
        list icmp_type '130/0'
        list icmp_type '131/0'
        list icmp_type '132/0'
        list icmp_type '143/0'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-ICMPv6-Input'
        option src 'wan'
        option proto 'icmp'
        list icmp_type 'echo-request'
        list icmp_type 'echo-reply'
        list icmp_type 'destination-unreachable'
        list icmp_type 'packet-too-big'
        list icmp_type 'time-exceeded'
        list icmp_type 'bad-header'
        list icmp_type 'unknown-header-type'
        list icmp_type 'router-solicitation'
        list icmp_type 'neighbour-solicitation'
        list icmp_type 'router-advertisement'
        list icmp_type 'neighbour-advertisement'
        option limit '1000/sec'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-ICMPv6-Forward'
        option src 'wan'
        option dest '*'
        option proto 'icmp'
        list icmp_type 'echo-request'
        list icmp_type 'echo-reply'
        list icmp_type 'destination-unreachable'
        list icmp_type 'packet-too-big'
        list icmp_type 'time-exceeded'
        list icmp_type 'bad-header'
        list icmp_type 'unknown-header-type'
        option limit '1000/sec'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-IPSec-ESP'
        option src 'wan'
        option dest 'lan'
        option proto 'esp'
        option target 'ACCEPT'

config rule
        option name 'Allow-ISAKMP'
        option src 'wan'
        option dest 'lan'
        option dest_port '500'
        option proto 'udp'
        option target 'ACCEPT'

frollic · February 1, 2023, 7:06pm

what's wan and wwan in this configuration ?

vlad.rusin.poltava · February 1, 2023, 7:50pm

vlad.rusin.poltava · February 1, 2023, 7:51pm

psherman · February 1, 2023, 7:53pm

I'd check two things:

from the OpenWrt router itself, can you ping an IP address successfully (for example 8.8.8.8)?
If you connect your PC to the Mifi LTE router, do you get internet access as expected?

vlad.rusin.poltava · February 1, 2023, 7:57pm

No
Yes, i get access.
I can also access the Mifi web panel through the OpenWRT network

psherman · February 1, 2023, 7:59pm

When connected to the Mifi device, what IP address does your computer get?

Also, does the Mifi have any specific limitations in terms of the number of devices that it will service or required MAC address registrations or authentication (or even a captive portal/splash page)?

vlad.rusin.poltava · February 1, 2023, 8:03pm

There are no limitations in Mifi. Only OpenWRT is connected to Mifi.
Снимок

psherman · February 1, 2023, 8:04pm

ok... let's see your complete config:

Please copy the output of the following commands and post it here using the "Preformatted text </> " button:

Remember to redact passwords, MAC addresses and any public IP addresses you may have:

cat /etc/config/network
cat /etc/config/wireless
cat /etc/config/dhcp
cat /etc/config/firewall

AndrewZ · February 1, 2023, 8:08pm

... and the output of ip r please

vlad.rusin.poltava · February 1, 2023, 8:16pm

Thank's

cat /etc/config/network
config interface 'loopback'
        option device 'lo'
        option proto 'static'
        option ipaddr '127.0.0.1'
        option netmask '255.0.0.0'

config globals 'globals'
        option ula_prefix 'fd34:0587:bd27::/48'

config device
        option name 'br-lan'
        option type 'bridge'
        list ports 'eth0.1'

config interface 'lan'
        option device 'br-lan'
        option proto 'static'
        option ipaddr '192.168.1.1'
        option netmask '255.255.255.0'
        option ip6assign '60'

config interface 'wan'
        option device 'eth0.2'
        option proto 'dhcp'

config interface 'wan6'
        option device 'eth0.2'
        option proto 'dhcpv6'

config switch
        option name 'switch0'
        option reset '1'
        option enable_vlan '1'

config switch_vlan
        option device 'switch0'
        option vlan '1'
        option ports '1 2 3 4 5t'

config switch_vlan
        option device 'switch0'
        option vlan '2'
        option ports '0 5t'

config interface 'wwan'
        option proto 'dhcp'
        option device 'wlan0'

cat /etc/config/wireless
config wifi-device 'radio0'
        option type 'mac80211'
        option path 'platform/ahb/180c0000.wmac'
        option band '2g'
        option htmode 'HT20'
        option channel 'auto'
        option cell_density '0'

config wifi-iface 'default_radio0'
        option device 'radio0'
        option network 'lan'
        option mode 'ap'
        option ssid 'OpenWrt'
        option encryption 'none'

config wifi-iface 'wifinet1'
        option device 'radio0'
        option mode 'sta'
        option network 'wwan'
        option ssid 'ExR.ntw'
        option bssid '28:80:A2:XXXX:D9'
        option encryption 'psk2'
        option key '*'


cat /etc/config/dhcp
config dnsmasq
        option domainneeded '1'
        option boguspriv '1'
        option filterwin2k '0'
        option localise_queries '1'
        option rebind_protection '1'
        option rebind_localhost '1'
        option local '/lan/'
        option domain 'lan'
        option expandhosts '1'
        option nonegcache '0'
        option authoritative '1'
        option readethers '1'
        option leasefile '/tmp/dhcp.leases'
        option resolvfile '/tmp/resolv.conf.d/resolv.conf.auto'
        option nonwildcard '1'
        option localservice '1'
        option ednspacket_max '1232'

config dhcp 'lan'
        option interface 'lan'
        option start '100'
        option limit '150'
        option leasetime '12h'
        option dhcpv4 'server'
        option dhcpv6 'server'
        option ra 'server'
        option ra_slaac '1'
        list ra_flags 'managed-config'
        list ra_flags 'other-config'

config dhcp 'wan'
        option interface 'wan'
        option ignore '1'

config odhcpd 'odhcpd'
        option maindhcp '0'
        option leasefile '/tmp/hosts/odhcpd'
        option leasetrigger '/usr/sbin/odhcpd-update'
        option loglevel '4'

cat /etc/config/firewall
config defaults
        option input 'ACCEPT'
        option output 'ACCEPT'
        option forward 'REJECT'

config zone
        option name 'lan'
        option input 'ACCEPT'
        option output 'ACCEPT'
        option forward 'ACCEPT'
        list network 'lan'

config zone
        option name 'wan'
        option input 'REJECT'
        option output 'ACCEPT'
        option forward 'REJECT'
        option masq '1'
        option mtu_fix '1'
        list network 'wan'
        list network 'wan6'
        list network 'wwan'

config forwarding
        option src 'lan'
        option dest 'wan'

config rule
        option name 'Allow-DHCP-Renew'
        option src 'wan'
        option proto 'udp'
        option dest_port '68'
        option target 'ACCEPT'
        option family 'ipv4'

config rule
        option name 'Allow-Ping'
        option src 'wan'
        option proto 'icmp'
        option icmp_type 'echo-request'
        option family 'ipv4'
        option target 'ACCEPT'

config rule
        option name 'Allow-IGMP'
        option src 'wan'
        option proto 'igmp'
        option family 'ipv4'
        option target 'ACCEPT'

config rule
        option name 'Allow-DHCPv6'
        option src 'wan'
        option proto 'udp'
        option dest_port '546'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-MLD'
        option src 'wan'
        option proto 'icmp'
        option src_ip 'fe80::/10'
        list icmp_type '130/0'
        list icmp_type '131/0'
        list icmp_type '132/0'
        list icmp_type '143/0'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-ICMPv6-Input'
        option src 'wan'
        option proto 'icmp'
        list icmp_type 'echo-request'
        list icmp_type 'echo-reply'
        list icmp_type 'destination-unreachable'
        list icmp_type 'packet-too-big'
        list icmp_type 'time-exceeded'
        list icmp_type 'bad-header'
        list icmp_type 'unknown-header-type'
        list icmp_type 'router-solicitation'
        list icmp_type 'neighbour-solicitation'
        list icmp_type 'router-advertisement'
        list icmp_type 'neighbour-advertisement'
        option limit '1000/sec'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-ICMPv6-Forward'
        option src 'wan'
        option dest '*'
        option proto 'icmp'
        list icmp_type 'echo-request'
        list icmp_type 'echo-reply'
        list icmp_type 'destination-unreachable'
        list icmp_type 'packet-too-big'
        list icmp_type 'time-exceeded'
        list icmp_type 'bad-header'
        list icmp_type 'unknown-header-type'
        option limit '1000/sec'
        option family 'ipv6'
        option target 'ACCEPT'

config rule
        option name 'Allow-IPSec-ESP'
        option src 'wan'
        option dest 'lan'
        option proto 'esp'
        option target 'ACCEPT'

config rule
        option name 'Allow-ISAKMP'
        option src 'wan'
        option dest 'lan'
        option dest_port '500'
        option proto 'udp'
        option target 'ACCEPT'

vlad.rusin.poltava · February 1, 2023, 8:19pm

 ip r

default via 192.168.11.1 dev wlan0  src 192.168.11.2
192.168.1.0/24 dev br-lan scope link  src 192.168.1.1
192.168.11.0/24 dev wlan0 scope link  src 192.168.11.2

psherman · February 1, 2023, 8:24pm

remove the device line below:

and then remove the BSSID (it's not necessary).

vlad.rusin.poltava:

config wifi-iface 'wifinet1'
        option device 'radio0'
        option mode 'sta'
        option network 'wwan'
        option ssid 'ExR.ntw'
        option bssid '28:80:A2:XXXX:D9'
        option encryption 'psk2'
        option key '*'

Then restart the router and see what happens.

vlad.rusin.poltava · February 1, 2023, 8:38pm

The WWAN interface has disappeared. The rest is unchanged

frollic · February 1, 2023, 8:46pm

I'd reset it,

then do scan -> join in the wifi section, and put the connection in the wan firewall zone,
that should be all you need to do.

mk24 · February 2, 2023, 12:14am

Yes absolutely start at defaults then:

In wifi, click the Advanced tab at the top and set to your country.
In wifi, click Scan then use the Join this Network wizard. (Use this only once after a reset to defaults. If you want to change something about the connection later, edit it in the regular configuration pages)
Make the IPv6 change described below.

This is interesting that DNS works (if it did not, you would get a "bad name" error), which means that some sort of connection to the Internet is active.

I note that the laptop connected with a dual-stack IPv4/IPv6 connection, so the ISP supports v6 and that may be why Internet usage on the laptop was possible. Change the wan6 device to @wwan to support dual stack over the wifi wan link.

ping 192.168.11.1 and traceroute 8.8.8.8 would be useful tests as well.