Need New DavidC502 Thread

Bogey · June 6, 2018, 4:06am

So it is the upload speed after reassociation?

Let me put my results here also

Initial association

Connecting to host 192.168.1.33, port 5201
[  4] local 192.168.1.181 port 46364 connected to 192.168.1.33 port 5201
[ ID] Interval           Transfer     Bandwidth
[  4]   0.00-1.01   sec  77.7 MBytes   642 Mbits/sec                  
[  4]   1.01-2.00   sec  76.2 MBytes   646 Mbits/sec                  
[  4]   2.00-3.00   sec  75.0 MBytes   629 Mbits/sec                  
[  4]   3.00-4.02   sec  75.0 MBytes   622 Mbits/sec                  
[  4]   4.02-5.01   sec  77.5 MBytes   655 Mbits/sec                  
[  4]   5.01-6.00   sec  76.2 MBytes   644 Mbits/sec                  
[  4]   6.00-7.01   sec  75.0 MBytes   623 Mbits/sec                  
[  4]   7.01-8.01   sec  71.2 MBytes   596 Mbits/sec                  
[  4]   8.01-9.00   sec  60.0 MBytes   509 Mbits/sec                  
[  4]   9.00-10.02  sec  76.2 MBytes   627 Mbits/sec                  
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth
[  4]   0.00-10.02  sec   740 MBytes   620 Mbits/sec                  sender
[  4]   0.00-10.02  sec   740 MBytes   619 Mbits/sec                  receiver

iperf Done.

After reassociation


Connecting to host 192.168.1.33, port 5201
[  4] local 192.168.1.181 port 46300 connected to 192.168.1.33 port 5201
[ ID] Interval           Transfer     Bandwidth
[  4]   0.00-1.01   sec   947 KBytes  7.67 Mbits/sec                  
[  4]   1.01-2.04   sec  0.00 Bytes  0.00 bits/sec                  
[  4]   2.04-3.04   sec   368 KBytes  3.01 Mbits/sec                  
[  4]   3.04-4.04   sec  0.00 Bytes  0.00 bits/sec                  
[  4]   4.04-5.02   sec  0.00 Bytes  0.00 bits/sec                  
[  4]   5.02-6.04   sec   382 KBytes  3.08 Mbits/sec                  
[  4]   6.04-7.04   sec  0.00 Bytes  0.00 bits/sec                  
[  4]   7.04-8.02   sec  0.00 Bytes  0.00 bits/sec                  
[  4]   8.02-9.02   sec  0.00 Bytes  0.00 bits/sec                  
[  4]   9.02-10.04  sec   382 KBytes  3.07 Mbits/sec                  
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth
[  4]   0.00-10.04  sec  2.03 MBytes  1.70 Mbits/sec                  sender
[  4]   0.00-10.04  sec  1.10 MBytes   920 Kbits/sec                  receiver

iperf Done.

AddRemover · June 6, 2018, 3:13pm

Just installed r7093 on my Rango and appears DarkMatter theme is a bit broken.

spuriousoffspring · June 6, 2018, 3:30pm

Had the same issue with my WRT32X. Darkmatter Theme was jumbled. The Bootstrap and Material Themes were fine.
Also, Advanced Reboot doesn't recognize the dual-partitions.

Kherby · June 6, 2018, 4:34pm

Advanced Reboot working fine here @r7093.... edit: but i'm using a WRT3200ACM.
adv_re

davidc502 · June 6, 2018, 6:21pm

This is where in Github the theme is pulled from --> https://github.com/apollo-ng/luci-theme-darkmatter

Appears there are two contributors to the project.

phinn · June 6, 2018, 7:00pm

They only recently got Advanced Reboot working on the WRT32000ACM with help from hnyman and stangri. Post about the WRT32X from link below. Provide them necessary info so they can fix it so it works as well:

AddRemover · June 7, 2018, 9:23am

There were no cahnges on github for half a year, so something was broken elsewhere.

thencein · June 8, 2018, 3:04pm

Does anyone else here have issues with some Android devices being randomly being kicked off the wifi? The only solution to this problem is to restart the router. Restarting the wifi via Luci or re-authenticating on the phone itself doesn't work.

hnyman · June 8, 2018, 4:42pm

Have you read the mwlwifi driver bug tracker?

github.com/kaloz/mwlwifi

Connection problems with Android clients

opened 08:14PM - 18 Jan 18 UTC

Alexander-r

On wrt3200acm with 10.3.4.0-20180118 and 9.3.2.4 firmware I have problems with A…ndroid clients. If i use wrt3200acm as a dhcp server and try to connect my phone then it may take around a minute to get an IP address and the client reconnects to the network a couple of times before it gets the address. If I set up wrt3200acm as a bridge and use another routers dhcp for lan clients then it takes 10-20 seconds for my phone to connect but after that it shows "Connected, no Internet". If it's the first time I connect to the network it asks if I want to stay connected. If I stay connected the network starts to work after some time. If on the phone I turn wi-fi off and on and it starts reconnecting automatically then after it gets "Connected, no Internet" it disconnects from the network and tries reconnecting to it again. It stays in this connect/disconnect loop until I connect to the network manually again. In both setups clients have access to internet. This problem only affects my Android devices. My notebooks connects to the network without any problems. I did not experience this problem with official 1.0.6.186168 firmware in both when wrt3200acm was a dhcp server and when it was in bridge mode. All the phones that I tested have at least Android 7 on them.

Kherby · June 8, 2018, 5:23pm

Running davidc's latest build on my WRT3200acm and i have zero problems so far ! Uptime: 5d 22h
I'm using SQM, dnscrypt-proxy, adblock, vlan's, ebtables and everything is working fine.
Wifi performance and range could be abit better but that's not related to his build quality...

btw if you use SQM and your ISP is enforcing a 24h disconnect@pppoe like my ISP, check out the following thread: [Solved/hotfixed] SQM does not reinitialize after ifdown/ifup

marcmicalizzi · June 8, 2018, 5:57pm

I wonder if the only difference is setup or maybe my router is screwed up somehow, latest build on my 3200acm starts having the wireless not work after a couple hours, and then after 8 or so hours runs out of memory

Kherby · June 8, 2018, 6:12pm

I had this "running out memory" problem with an earlier build, not sure what the reason was.
Than i haven't used the device for a while as i tried out a different router and when i jumped back and flashed a newer build the problem was gone... Pretty weird tho !
I think it's somehow related to mwlwifi...

antonsamoziv · June 9, 2018, 8:56am

@davidc502 It doesn't really make sense for everyone to be posting in this
thread with the current title since it looks like everyone's decided to migrate

JW0914 · June 10, 2018, 11:37am

I didn't bother to check his new repo the first time around, but it appears what he had previously said on the OpenWrt forum regarding no longer doing community builds, except for his own devices, is true, as he no longer offers WRT AC Series builds.

With that being said, I encourage users to at least check out the config files @escalade uses in his builds, as he truly has one of the most highly customized OpenWrt builds.

Kherby · June 10, 2018, 7:37pm

Uhm... so davidc doesn't offer community builds anymore for the WRT3200acm ?
If that's true im very sad !!

dos · June 10, 2018, 7:43pm

I don’t recall seeing anything about stopping. The latest are June 2.

https://davidc502sis.dynamic-dns.net

anomeome · June 10, 2018, 7:56pm

Yes, I did not mean to imply that the full gamut of devices that were being built before was still the case. just that the individual was still here about, with a build on offering.

davidc502 · June 11, 2018, 12:27pm

It's all good... I'm still here, and builds are still available on the website. Currently, the plan is to continue.

JW0914 · June 11, 2018, 12:30pm

@anomeome Ah, I misunderstood your post.

My post was in reply to a post regarding arokh's build repo, not @davidc502's, which was regarding an older post explaining the lack of 3rd party community builds

In order to see the post someone is replying to, click on the forward arrow next to the username in the upper right hand corner of a reply.

YummyHamster · June 11, 2018, 12:30pm

Thanks for all the work, time and effort you put into this. I'm using the builds for over a year now without any big issues.