Thu Jan 31 03:59:23 2019 kern.info kernel: [ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0
Detected at startup openwrt chip QCA9533, true chip QCA9531
https://openwrt.org/toh/hwdata/mikrotik/mikrotik_rb952ui-5ac2nd_hap_ac_lite
As a result, if you force a card, it is flashed normally, but there is no switch configuration and port LEDs. WLAN 5g (QCA9887) does not work, USB does not have a power port, port 5 is lit red (gpio14) it turns off if the gpio value is 0
Chip photo
@Pahalan
Hey,
In the meantime a similar fix landed in the master tree, so images should je available.
Regards,
Koen
@xback
I checked today the image from the master tree, the problem persists
root@OpenWrt:~# cat /tmp/sysinfo/board_name unknown
Could you share the output of:
dmesg
cat /proc/cpuinfo
I'll take a look as soon as I can.
Thanks,
Koen
BusyBox v1.31.0 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r10243-4d11c4c378
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:~# dmesg
[ 0.000000] Linux version 4.14.125 (buildbot@602ce18687ab) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r10243-4d11c4c378)) #0 Mon Jun 17 04:53:07 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 805cd3e0, node_mem_map 81000020
[ 0.000000] Normal zone: 144 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] random: get_random_bytes called from start_kernel+0x98/0x4a8 with crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240
[ 0.000000] Kernel command line: no-uart no-buzzer no-nand parts=1 boot_part_size=16777216 gpio=8520495 HZ=325000000 mem=64M kmac=B8:69:F4:97:62:F8 board=952-hb board=952-hb hw_opt=00294005 boot=0 mlc=11 console=ttyS0,115200 rootfstype=squashfs noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 56500K/65536K available (4400K kernel code, 191K rwdata, 968K rodata, 2176K init, 218K bss, 9036K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] Clocks: CPU:650.000MHz, DDR:600.000MHz, AHB:300.000MHz, Ref:25.000MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5880801374 ns
[ 0.000009] sched_clock: 32 bits at 325MHz, resolution 3ns, wraps every 6607641598ns
[ 0.008865] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688)
[ 0.075995] pid_max: default: 32768 minimum: 301
[ 0.081503] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.089017] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.100046] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.111266] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.119497] NET: Registered protocol family 16
[ 0.128149] MIPS: machine is MikroTik RouterBOARD RB952Ui-5ac2nD
[ 0.139303] registering PCI controller with io_map_base unset
[ 0.644258] PCI host bridge to bus 0000:00
[ 0.648977] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[ 0.656777] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.663106] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.670810] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.679834] pci 0000:00:00.0: [168c:0050] type 00 class 0x028000
[ 0.679899] pci 0000:00:00.0: reg 0x10: [mem 0x10000000-0x101fffff 64bit]
[ 0.679979] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.680053] pci 0000:00:00.0: supports D1
[ 0.680062] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.680271] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.680299] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
[ 0.688614] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref]
[ 0.700340] clocksource: Switched to clocksource MIPS
[ 0.707213] NET: Registered protocol family 2
[ 0.713054] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.721034] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.728258] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.735628] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.742313] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.749714] NET: Registered protocol family 1
[ 0.754742] PCI: CLS 0 bytes, default 32
[ 2.590349] random: fast init done
[ 3.806756] Crashlog allocated RAM at address 0x3f00000
[ 3.814220] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[ 3.827549] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 3.834225] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 3.982063] io scheduler noop registered
[ 3.986516] io scheduler deadline registered (default)
[ 3.992828] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 4.002085] console [ttyS0] disabled
[ 4.026288] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[ 4.036094] console [ttyS0] enabled
[ 4.043654] bootconsole [early0] disabled
[ 4.059920] m25p80 spi0.0: found w25q128jv, expected m25p80
[ 4.075521] m25p80 spi0.0: w25q128jv (16384 Kbytes)
[ 4.122017] Creating 6 MTD partitions on "spi0.0":
[ 4.126989] 0x000000000000-0x00000000e000 : "routerboot"
[ 4.154752] 0x00000000e000-0x00000000f000 : "hard_config"
[ 4.182649] 0x00000000f000-0x000000010000 : "bios"
[ 4.209937] 0x000000010000-0x00000001f000 : "routerboot2"
[ 4.237837] 0x00000001f000-0x000000020000 : "soft_config"
[ 4.265770] 0x000000020000-0x000001000000 : "firmware"
[ 4.272207] 2 minor-fw partitions found on MTD device firmware
[ 4.278249] 0x000000020000-0x000000190000 : "kernel"
[ 4.284154] 0x000000190000-0x000001000000 : "rootfs"
[ 4.289920] mtd: device 7 (rootfs) set to be root filesystem
[ 4.295858] 1 squashfs-split partitions found on MTD device rootfs
[ 4.302256] 0x0000003d0000-0x000001000000 : "rootfs_data"
[ 4.332885] libphy: Fixed MDIO Bus: probed
[ 4.462982] libphy: ag71xx_mdio: probed
[ 5.092988] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[ 5.103015] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 5.732888] ag71xx-mdio.1: Found an AR934X built-in switch
[ 5.786102] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 5.796869] NET: Registered protocol family 10
[ 5.805154] Segment Routing with IPv6
[ 5.809035] NET: Registered protocol family 17
[ 5.813761] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 5.827156] 8021q: 802.1Q VLAN Support v1.8
[ 5.848128] Freeing unused kernel memory: 2176K
[ 5.852842] This architecture does not have kernel memory protection.
[ 5.875685] init: Console is alive
[ 5.879449] init: - watchdog -
[ 5.903995] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.913291] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.931287] init: - preinit -
[ 6.108813] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 8.203979] eth0: link up (100Mbps/Full duplex)
[ 8.208698] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 9.285316] eth0: link down
[ 9.299513] procd: - early -
[ 9.303403] procd: - watchdog -
[ 9.892134] procd: - watchdog -
[ 9.895693] procd: - ubus -
[ 9.905726] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.949196] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.956277] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.963848] procd: - init -
[ 10.420964] kmodloader: loading kernel modules from /etc/modules.d/*
[ 10.445211] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.468106] Loading modules backported from Linux version v4.19.32-0-g3a2156c839c7
[ 10.476009] Backport generated by backports.git v4.19.32-1-0-g1c4f7569
[ 10.499910] urngd: v1.0.0 started.
[ 10.506021] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.528907] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 10.654068] xt_time: kernel timezone is -0000
[ 10.775952] PPP generic driver version 2.4.2
[ 10.791368] NET: Registered protocol family 24
[ 10.864560] ath: EEPROM regdomain: 0x0
[ 10.864569] ath: EEPROM indicates default country code should be used
[ 10.864573] ath: doing EEPROM country->regdmn map search
[ 10.864587] ath: country maps to regdmn code: 0x3a
[ 10.864592] ath: Country alpha2 being used: US
[ 10.864596] ath: Regpair used: 0x3a
[ 10.877520] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 10.879485] ieee80211 phy0: Atheros AR9531 Rev:2 mem=0xb8100000, irq=47
[ 10.917689] random: crng init done
[ 10.921258] random: 7 urandom warning(s) missed due to ratelimiting
[ 10.950859] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 21.654327] br-lan: port 1(eth0) entered blocking state
[ 21.659738] br-lan: port 1(eth0) entered disabled state
[ 21.665506] device eth0 entered promiscuous mode
[ 21.686213] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 21.799683] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 24.763901] eth0: link up (100Mbps/Full duplex)
[ 24.768632] br-lan: port 1(eth0) entered blocking state
[ 24.774078] br-lan: port 1(eth0) entered forwarding state
[ 24.781707] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 27.882416] eth0: link down
[ 27.886030] br-lan: port 1(eth0) entered disabled state
[ 29.042810] eth1: link up (1000Mbps/Full duplex)
[ 29.047614] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 93.811718] eth1: link down
[ 95.484019] eth0: link up (100Mbps/Full duplex)
[ 95.488755] br-lan: port 1(eth0) entered blocking state
[ 95.494207] br-lan: port 1(eth0) entered forwarding state
root@OpenWrt:~# cat /proc/cpuinfo
system type : Qualcomm Atheros QCA9533 ver 2 rev 0
machine : MikroTik RouterBOARD RB952Ui-5ac2nD
processor : 0
cpu model : MIPS 24Kc V7.4
BogoMIPS : 432.53
wait instruction : yes
microsecond timers : yes
tlb_entries : 16
extra interrupt vector : yes
hardware watchpoint : yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb]
isa : mips1 mips2 mips32r1 mips32r2
ASEs implemented : mips16
Options implemented : tlb 4kex 4k_cache prefetch mcheck ejtag llsc dc_aliases perf_cntr_intr_bit nan_legacy nan_2008 perf
shadow register sets : 1
kscratch registers : 0
package : 0
core : 0
VCED exceptions : not available
VCEI exceptions : not available
Hi,
A large fix for Mikrotik board detection landed shortly after your build above.
Could you retest by building the latest 19.07 branch?
Thanks
@xback
Hi!
I can not build the last branch 19.07. Maybe there is a built image ?. There is no download on the official page 19.07. Check 18.06.4 - does not work (
Hey. I experienced the same issues as you.
I just built a the 19.07 version for this device, but have not yet tested it.
You can find it here https://gitlab.com/nkay08/openwrt-ar71xx-mikrotik-rb-nor-flash-16m-ac/tree/master/19.07/ar71xx/mikrotik.
I will test it as soon as I get home.
a whole bunch of devices in a single mach file, it is really wonder there are no more problems than just a few. probably you need to first verify your hardware version and then compare it with hw version of a user that added initial support. after that recheck gpio settings and similar.
I updated my repository.
https://gitlab.com/nkay08/openwrt-ar71xx-mikrotik-rb-nor-flash-16m-ac
You can find builds in openwrt/bin/targets/.../.... I have several branches with different build options.
For example with the useful sqm package: https://gitlab.com/nkay08/openwrt-ar71xx-mikrotik-rb-nor-flash-16m-ac/tree/19.07-luci-extra
Have you tested Dynamic VLANs configuration in this device? In my configuration I am not able to make them work. I have successfully used 8021x in other OpenWRT devices though with the same config.
wireless:
config wifi-iface 'wifinet1'
option device 'radio1'
option mode 'ap'
option encryption 'wpa2'
option auth_secret 'radiussecret'
option dynamic_vlan '2'
option vlan_tagged_interface 'eth1'
option vlan_bridge 'br-vlan'
option vlan_naming '0'
option auth_server '192.168.2.1'
option ssid 'ssid-radius'
network:
config interface 'vlan1'
option type 'bridge'
option ifname 'eth1.1'
option proto 'static'
option netmask '255.255.255.0'
option gateway '192.168.2.1'
option ipaddr '192.168.2.251'
config interface 'vlan3'
option ifname 'eth1.3'
option proto 'static'
option ipaddr '192.168.3.251'
option netmask '255.255.255.0'
option type 'bridge'
config switch
option name 'switch0'
option reset '1'
option enable_vlan '1'
option ar8xxx_mib_type '0'
option ar8xxx_mib_poll_interval '500'
config switch_vlan
option device 'switch0'
option vlan '1'
option vid '1'
option ports '4 3 2 1t 0t'
config switch_vlan
option device 'switch0'
option vlan '2'
option vid '3'
option ports '1t 0t
One more Question/remark: Tagged & Untagged VLAN on the Same Port also does not work. Is this a device restriction?
Hi, anyone could install 21.02 on this router? If so, how, which image?
Thanks!
Not supported till now, have ask to help here:
Maybe someone can assist to develop 21.02 support...
21.02.x is done and dusted, apart from bugfixes, nothing is going to happen there.
22.03.x is branched and in its -rc phase, that /might/ still allow in (easy-) new device additions, but if you do want anything you to happen, someone (which might end up being you, yourself) will have to provide a patch set against master/ snapshots. Only master accepts new devices additions, only once it's been added there, it /might/ be backported to 22.03.x, but chances for 21.02.x are essentially zero at this point.
Already have run it successfully on 21.02.3. Thnx.)
What can be done - and what stands a chance for backporting to the official 21.02.x are two different pairs of shoes. The precondition is always to go through master, from there are still quite reasonable chances for 22.03.x, but only minimal ones for 22.02.x.
Hello expert,
I also see this problem on my Meraki MR33 platform. The error message as below:
Thu Jun 9 23:19:11 2022 kern.info kernel: [ 18.319701] ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x50.
Thu Jun 9 23:19:11 2022 kern.info kernel: [ 18.320525] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
Thu Jun 9 23:19:11 2022 kern.info kernel: [ 18.327006] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
Thu Jun 9 23:19:11 2022 kern.info kernel: [ 20.060182] ath10k_pci 0000:01:00.0: qca9887 hw1.0 target 0x4100016d chip_id 0x004000ff sub 0000:0000
Thu Jun 9 23:19:11 2022 kern.info kernel: [ 20.060238] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
Thu Jun 9 23:19:11 2022 kern.info kernel: [ 20.070276] ath10k_pci 0000:01:00.0: firmware ver 10.1-ct-87-__fW-022-ecad3248 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT crc32 61a92df5
Thu Jun 9 23:19:11 2022 kern.info kernel: [ 20.197474] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 546cca0d
Thu Jun 9 23:19:11 2022 kern.err kernel: [ 20.198037] ath10k_pci 0000:01:00.0: failed to read device EEPROM at 0000
Thu Jun 9 23:19:11 2022 kern.warn kernel: [ 20.203731] ath10k_pci 0000:01:00.0: failed to read calibration data from EEPROM: -22
Thu Jun 9 23:19:11 2022 kern.err kernel: [ 20.238607] ath10k_pci 0000:01:00.0: otp calibration failed: 2
Thu Jun 9 23:19:11 2022 kern.err kernel: [ 20.238654] ath10k_pci 0000:01:00.0: failed to run otp: -22 (download-cal-data)
Thu Jun 9 23:19:11 2022 kern.err kernel: [ 20.243423] ath10k_pci 0000:01:00.0: could not init core (-22)
Thu Jun 9 23:19:11 2022 kern.err kernel: [ 20.250727] ath10k_pci 0000:01:00.0: could not probe fw (-22)
Thu Jun 9 23:19:11 2022 kern.info kernel: [ 21.559596] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003900ff sub 0000:0000
Thu Jun 9 23:19:11 2022 kern.info kernel: [ 21.559654] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
Thu Jun 9 23:19:11 2022 kern.info kernel: [ 21.572451] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
Thu Jun 9 23:19:11 2022 kern.err kernel: [ 21.650540] ath10k_ahb a000000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000,variant=Meraki-MR33 from ath10k/QCA4019/hw1.0/board-2.bin
Thu Jun 9 23:19:11 2022 kern.err kernel: [ 21.698362] ath10k_ahb a000000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0
Thu Jun 9 23:19:11 2022 kern.err kernel: [ 21.698419] ath10k_ahb a000000.wifi: failed to fetch board file: -12
Thu Jun 9 23:19:11 2022 kern.err kernel: [ 21.706904] ath10k_ahb a000000.wifi: could not probe fw (-12)
Thu Jun 9 23:19:11 2022 kern.info kernel: [ 22.911417] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003900ff sub 0000:0000
Thu Jun 9 23:19:11 2022 kern.info kernel: [ 22.911474] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
Thu Jun 9 23:19:11 2022 kern.info kernel: [ 22.924252] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
Thu Jun 9 23:19:11 2022 kern.err kernel: [ 22.955212] ath10k_ahb a800000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000,variant=Meraki-MR33 from ath10k/QCA4019/hw1.0/board-2.bin
Thu Jun 9 23:19:11 2022 kern.err kernel: [ 23.050161] ath10k_ahb a800000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0
Thu Jun 9 23:19:11 2022 kern.err kernel: [ 23.050218] ath10k_ahb a800000.wifi: failed to fetch board file: -12
Thu Jun 9 23:19:11 2022 kern.err kernel: [ 23.058612] ath10k_ahb a800000.wifi: could not probe fw (-12)
Thu Jun 9 23:19:11 2022 user.info kernel: [ 23.078074] kmodloader: done loading kernel modules from /etc/modules.d/*
Now I am compiling the code and hope it works well.
Regards