You probably wiped the wifi calibration data.
if i start device normaly no boot
F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 0236 [010F]
Jump to BL
NOTICE: BL2: v2.9(release):OpenWrt v2023-07-24-00ac6db3-2 (mt7981-spim-nand-ddr3)
NOTICE: BL2: Built : 12:34:46, Sep 23 2024
NOTICE: WDT: Cold boot
NOTICE: WDT: disabled
NOTICE: EMI: Using DDR3 settings
if start with mtk_uartboot -s com3 --aarch64 -p mt7981-ram-ddr4-bl2.bin -f mt7981-rfb-spim-nand-bl31-uboot.fip
mtk_uartboot - 0.1.1
Using serial port: com3
Handshake...
hw code: 0x7981
hw sub code: 0x8a00
hw ver: 0xca00
sw ver: 0x1
Baud rate set to 460800
sending payload to 0x201000...
Checksum: 0x2bf3
Setting baudrate back to 115200
Jumping to 0x201000 in aarch64...
Waiting for BL2. Message below:
==================================
NOTICE: BL2: v2.10.0 (release):OpenWrt v2024.01.17~bacca82a-3 (mt7981-ram-ddr4)
NOTICE: BL2: Built : 13:32:43, Jan 27 2025
NOTICE: WDT: Cold boot
NOTICE: WDT: disabled
NOTICE: EMI: Using DDR4 settings
NOTICE: EMI: Detected DRAM size: 1024MB
NOTICE: EMI: complex R/W mem test passed
NOTICE: CPU: MT7981 (1300MHz)
NOTICE: Starting UART download handshake ...
==================================
BL2 UART DL version: 0x10
Baudrate set to: 921600
FIP sent.
==================================
==================================40400000 ...
boot
MT7981> bootm
## Loading kernel from FIT Image at 46000000 ...
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-5.15.167
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x460000ec
Data Size: 3781454 Bytes = 3.6 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x48000000
Entry Point: 0x48000000
Hash algo: crc32
Hash value: ed237e3a
Hash algo: sha1
Hash value: 62362639aecdfc48a48ab20b70286ac97e1ca56f
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 46000000 ...
Using 'config-1' configuration
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt glinet_gl-mt3000 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x4639b57c
Data Size: 22489 Bytes = 22 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: ce6dc19b
Hash algo: sha1
Hash value: 251c2c669793bcb9e69186ca5ea7bbf28b2a5f94
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x4639b57c
Working FDT set to 4639b57c
Uncompressing Kernel Image
Loading Device Tree to 000000007f7f3000, end 000000007f7fb7d8 ... OK
Working FDT set to 7f7f3000
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.15.167 (builder@buildhost) (aarch64-openwrt-linux -musl-gcc (OpenWrt GCC 12.3.0 r24106-10cc5fcd00) 12.3.0, GNU ld (GNU Binutils) 2 .40.0) #0 SMP Mon Sep 23 12:34:46 2024
[ 0.000000] Machine model: GL.iNet GL-MT3000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff]
[ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff]
[ 0.000000] node 0: [mem 0x0000000043030000-0x0000000047c7ffff]
[ 0.000000] node 0: [mem 0x0000000047c80000-0x0000000047ffffff]
[ 0.000000] node 0: [mem 0x0000000048000000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.4
[ 0.000000] percpu: Embedded 18 pages/cpu s33112 r8192 d32424 u73728
[ 0.000000] pcpu-alloc: s33112 r8192 d32424 u73728 alloc=18*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: kernel page table isolation disabled by kernel conf iguration
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048
[ 0.000000] Kernel command line:
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, li near)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 1012768K/1048576K available (8448K kernel code, 904K rwda ta, 1488K rodata, 448K init, 302K bss, 35808K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jif fies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 640 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] Root IRQ handler: 0xffffffc008010090
[ 0.000000] GICv3: 16 PPIs implemented
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
[ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
[ 0.000001] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 43980 46511101ns
[ 0.000142] Calibrating delay loop (skipped), value calculated using timer fr equency.. 26.00 BogoMIPS (lpj=130000)
[ 0.000153] pid_max: default: 32768 minimum: 301
[ 0.000452] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, line ar)
[ 0.000466] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.001819] rcu: Hierarchical SRCU implementation.
[ 0.002205] smp: Bringing up secondary CPUs ...
[ 0.002538] Detected VIPT I-cache on CPU1
[ 0.002566] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000
[ 0.002596] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.002664] smp: Brought up 1 node, 2 CPUs
[ 0.002678] SMP: Total of 2 processors activated.
[ 0.002684] CPU features: detected: 32-bit EL0 Support
[ 0.002689] CPU features: detected: CRC32 instructions
[ 0.002720] CPU features: emulated: Privileged Access Never (PAN) using TTBR0 _EL1 switching
[ 0.002785] CPU: All CPU(s) started at EL2
[ 0.002796] alternatives: patching kernel code
[ 0.006287] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns
[ 0.006313] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.006471] pinctrl core: initialized pinctrl subsystem
[ 0.007337] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.007661] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.007693] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allo cations
[ 0.007716] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic al locations
[ 0.008071] thermal_sys: Registered thermal governor 'fair_share'
[ 0.008075] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.008079] thermal_sys: Registered thermal governor 'step_wise'
[ 0.008084] thermal_sys: Registered thermal governor 'user_space'
[ 0.008266] ASID allocator initialised with 65536 entries
[ 0.008734] pstore: Registered ramoops as persistent store backend
[ 0.008740] ramoops: using 0x10000@0x42ff0000, ecc: 0
[ 0.019909] cryptd: max_cpu_qlen set to 1000
[ 0.022781] SCSI subsystem initialized
[ 0.022963] libata version 3.00 loaded.
[ 0.024221] clocksource: Switched to clocksource arch_sys_counter
[ 0.024865] NET: Registered PF_INET protocol family
[ 0.024999] IP idents hash table entries: 16384 (order: 5, 131072 bytes, line ar)
[ 0.025657] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.025681] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.025691] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.025753] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear )
[ 0.025857] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.025953] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.025980] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.026138] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.026163] PCI: CLS 0 bytes, default 64
[ 0.028709] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[ 0.032454] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.032472] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc.
[ 0.065933] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 51)
[ 0.067146] pwm-mediatek 10048000.pwm: clock: top fail: -517
[ 0.077732] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.080089] printk: console [ttyS0] disabled
[ 0.100293] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 18, base_baud = 2500000) is a ST16650V2
[ 0.722553] printk: console [ttyS0] enabled
[ 0.727642] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.737252] loop: module loaded
[ 0.740399] Loading iSCSI transport class v2.0-870.
[ 0.747363] spi spi0.0: setup: ignoring unsupported mode bits a00
[ 0.754699] spi-nand spi0.0: calibration result: 0x3
[ 0.759758] spi-nand spi0.0: Winbond SPI NAND was found.
[ 0.765084] spi-nand spi0.0: 256 MiB, block size: 128 KiB, page size: 2048, O OB size: 128
[ 0.773833] Signature found at block 2047 [0x0ffe0000]
[ 0.778983] NMBM management region starts at block 1920 [0x0f000000]
[ 0.787858] First info table with writecount 0 found in block 1920
[ 0.801565] Second info table with writecount 0 found in block 1923
[ 0.807838] NMBM has been successfully attached
[ 0.812685] 6 fixed-partitions partitions found on MTD device spi0.0
[ 0.819594] Creating 6 MTD partitions on "spi0.0":
[ 0.824419] 0x000000000000-0x000000100000 : "BL2"
[ 0.830217] 0x000000100000-0x000000180000 : "u-boot-env"
[ 0.836362] 0x000000180000-0x000000380000 : "Factory"
[ 0.843115] 0x000000380000-0x000000580000 : "FIP"
[ 0.849500] 0x000000580000-0x0000005c0000 : "log"
[ 0.854898] 0x0000005c0000-0x00000fc00000 : "ubi"
[ 0.859607] mtd: partition "ubi" extends beyond the end of device "spi0.0" -- size truncated to 0xea40000
[ 1.135908] mtk_soc_eth 15100000.ethernet: generated random MAC address 02:46 :0a:cd:92:15
[ 1.144601] mtk_soc_eth 15100000.ethernet: generated random MAC address c6:e8 :c5:cc:bc:e1
[ 1.212085] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xff ffffc009500000, irq 82
[ 1.222018] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xff ffffc009500000, irq 82
[ 1.231734] i2c_dev: i2c /dev entries driver
[ 1.237474] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowa yout=0)
[ 1.246375] NET: Registered PF_INET6 protocol family
[ 1.252291] Segment Routing with IPv6
[ 1.256013] In-situ OAM (IOAM) with IPv6
[ 1.259991] NET: Registered PF_PACKET protocol family
[ 1.265077] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.278203] 8021q: 802.1Q VLAN Support v1.8
[ 1.283438] pstore: Using crash dump compression: deflate
[ 1.298475] phy phy-usb-phy@11e10000.1: type_sw - reg 0x218, index 0
[ 1.306316] UBI: auto-attach mtd5
[ 1.309641] ubi0: default fastmap pool size: 90
[ 1.314160] ubi0: default fastmap WL pool size: 45
[ 1.318964] ubi0: attaching mtd5
[ 2.454182] random: crng init done
[ 2.855263] ubi0: scanning is finished
[ 2.869330] ubi0 warning: 0xffffffc00856dd14: cannot reserve enough PEBs for bad PEB handling, reserved 36, need 38
[ 2.880629] ubi0: attached mtd5 (name "ubi", size 234 MiB)
[ 2.886138] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 2.893003] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 2.899782] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 2.906734] ubi0: good PEBs: 1874, bad PEBs: 0, corrupted PEBs: 0
[ 2.912813] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 12 8
[ 2.920025] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequ ence number: 0
[ 2.928366] ubi0: available PEBs: 0, total reserved PEBs: 1874, PEBs reserved for bad PEB handling: 36
[ 2.937673] ubi0: background thread "ubi_bgt0d" started, PID 435
[ 2.939630] block ubiblock0_1: created from ubi0:1(rootfs)
[ 2.949170] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 2.956364] clk: Disabling unused clocks
[ 2.967822] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 2.975185] Freeing unused kernel memory: 448K
[ 2.979664] Run /sbin/init as init process
[ 2.983748] with arguments:
[ 2.986711] /sbin/init
[ 2.989406] with environment:
[ 2.992533] HOME=/
[ 2.994885] TERM=linux
[ 3.230669] init: Console is alive
[ 3.234262] init: - watchdog -
[ 3.793877] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.833910] usbcore: registered new interface driver usbfs
[ 3.839474] usbcore: registered new interface driver hub
[ 3.844842] usbcore: registered new device driver usb
[ 3.854976] xhci-mtk 11200000.usb: xHCI Host Controller
[ 3.860219] xhci-mtk 11200000.usb: new USB bus registered, assigned bus numbe r 1
[ 3.870637] xhci-mtk 11200000.usb: hcc params 0x01403f99 hci version 0x110 qu irks 0x0000000000210010
[ 3.879820] xhci-mtk 11200000.usb: irq 87, io mem 0x11200000
[ 3.885590] xhci-mtk 11200000.usb: xHCI Host Controller
[ 3.890811] xhci-mtk 11200000.usb: new USB bus registered, assigned bus numbe r 2
[ 3.898213] xhci-mtk 11200000.usb: Host supports USB 3.2 Enhanced SuperSpeed
[ 3.905752] hub 1-0:1.0: USB hub found
[ 3.909540] hub 1-0:1.0: 1 port detected
[ 3.913810] usb usb2: We don't know the algorithms for LPM for this host, dis abling LPM.
[ 3.922370] hub 2-0:1.0: USB hub found
[ 3.926203] hub 2-0:1.0: 1 port detected
[ 3.933785] kmodloader: done loading kernel modules from /etc/modules-boot.d/ *
[ 3.946523] init: - preinit -
[ 4.338013] mtk_soc_eth 15100000.ethernet eth1: PHY [mdio-bus:00] driver [Med iaTek MT7981 PHY] (irq=POLL)
[ 4.352975] mtk_soc_eth 15100000.ethernet eth1: configuring for phy/gmii link mode
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.404411] mtk_soc_eth 15100000.ethernet eth1: Link is Up - 100Mbps/Full - f low control rx/tx
[ 6.404430] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 6.593292] mount_root: loading kmods from internal overlay
[ 6.608475] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 6.618949] kmodloader: done loading kernel modules from //etc/modules-boot.d /*
[ 6.813528] UBIFS (ubi0:2): Mounting in unauthenticated mode
[ 6.819319] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 577
[ 6.876761] UBIFS (ubi0:2): recovery needed
[ 7.032404] UBIFS (ubi0:2): recovery completed
[ 7.036934] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "root fs_data"
[ 7.044766] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O u nit sizes: 2048 bytes/2048 bytes
[ 7.054671] UBIFS (ubi0:2): FS size: 219033600 bytes (208 MiB, 1725 LEBs), ma x 1737 LEBs, journal size 10919936 bytes (10 MiB, 86 LEBs)
[ 7.066833] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB)
[ 7.073433] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 67AE6 D72-EEE5-418B-B38F-34904879AD9A, small LPT model
[ 7.086619] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 7.100609] block: extroot: not configured
[ 7.104858] UBIFS (ubi0:2): un-mount UBI device 0
[ 7.109574] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" stops
[ 7.119700] UBIFS (ubi0:2): Mounting in unauthenticated mode
[ 7.125468] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 580
[ 7.223709] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "root fs_data"
[ 7.231568] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O u nit sizes: 2048 bytes/2048 bytes
[ 7.241472] UBIFS (ubi0:2): FS size: 219033600 bytes (208 MiB, 1725 LEBs), ma x 1737 LEBs, journal size 10919936 bytes (10 MiB, 86 LEBs)
[ 7.253646] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB)
[ 7.260252] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 67AE6 D72-EEE5-418B-B38F-34904879AD9A, small LPT model
[ 7.361687] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 7.374820] block: extroot: not configured
[ 7.381199] mount_root: switching to ubifs overlay
[ 7.393310] overlayfs: null uuid detected in lower fs '/', falling back to xi no=off,index=off,nfs_export=off.
[ 7.408030] urandom-seed: Seeding with /etc/urandom.seed
[ 7.442487] mtk_soc_eth 15100000.ethernet eth1: Link is Down
[ 7.458383] procd: - early -
[ 7.461352] procd: - watchdog -
Failed to connect to ubus
[ 8.009193] procd: - watchdog -
[ 8.071443] procd: - ubus -
[ 8.234641] procd: - init -
Please press Enter to activate this console.
[ 8.586170] kmodloader: loading kernel modules from /etc/modules.d/*
[ 8.642822] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433(alg:7fcdfc00)/0/0/0
[ 8.664044] usbcore: registered new interface driver cdc_wdm
[ 8.670820] Loading modules backported from Linux version v6.1.110-0-g5f55cad62cc9d
[ 8.678521] Backport generated by backports.git v6.1.110-1-0-g965f73fc
[ 8.696352] usbcore: registered new interface driver usbserial_generic
[ 8.702940] usbserial: USB Serial support registered for generic
[ 8.711047] usbcore: registered new interface driver cdc_ether
[ 8.718241] usbcore: registered new interface driver cdc_ncm
[ 8.737869] usbcore: registered new interface driver huawei_cdc_ncm
[ 8.872464] urngd: v1.0.2 started.
[ 9.067019] mt798x-wmac 18000000.wifi: HW/SW Version: 0x8a108a10, Build Time: 20221208201745a
[ 9.067019]
[ 9.299104] mt798x-wmac 18000000.wifi: WM Firmware Version: ____000000, Build Time: 20221208201806
[ 9.415312] mt798x-wmac 18000000.wifi: WA Firmware Version: DEV_000000, Build Time: 20221208202048
[ 9.506837] mt798x-wmac 18000000.wifi: eeprom load fail, use default bin
[ 9.513610] mt798x-wmac 18000000.wifi: Direct firmware load for mediatek/mt7981_eeprom_mt7976_dbdc.bin failed with error -2
[ 9.524749] mt798x-wmac 18000000.wifi: Falling back to sysfs fallback for: mediatek/mt7981_eeprom_mt7976_dbdc.bin
[ 10.131760] mt798x-wmac: probe of 18000000.wifi failed with error -12
[ 10.164080] PPP generic driver version 2.4.2
[ 10.169849] NET: Registered PF_PPPOX protocol family
[ 10.176213] usbcore: registered new interface driver qmi_wwan
[ 10.184699] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 10.192525] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 10.203170] usbcore: registered new interface driver cdc_mbim
[ 10.211915] usbcore: registered new interface driver option
[ 10.217646] usbserial: USB Serial support registered for GSM modem (1-port)
[ 10.226437] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 14.589905] mtk_soc_eth 15100000.ethernet eth1: PHY [mdio-bus:00] driver [MediaTek MT7981 PHY] (irq=POLL)
[ 14.605290] mtk_soc_eth 15100000.ethernet eth1: configuring for phy/gmii link mode
[ 14.616058] br-lan: port 1(eth1) entered blocking state
[ 14.621294] br-lan: port 1(eth1) entered disabled state
[ 14.626761] device eth1 entered promiscuous mode
[ 14.657272] mtk_soc_eth 15100000.ethernet eth0: validation of with support 0000000,00000000,00006000 and advertisement 0000000,00000000,00000000 failed: -22
[ 14.671542] mtk_soc_eth 15100000.ethernet eth0: mtk_open: could not attach PHY: -22
[ 16.724390] mtk_soc_eth 15100000.ethernet eth1: Link is Up - 100Mbps/Full - flow control rx/tx
[ 16.724414] br-lan: port 1(eth1) entered blocking state
[ 16.738228] br-lan: port 1(eth1) entered forwarding state
[ 16.743833] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
BusyBox v1.36.1 (2025-01-28 07:36:43 UTC) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt 23.05.5, r24106-10cc5fcd00
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/#
thank you preloader mt7981_openembed_som7981 work with my device and im able to work like charm now how make wifi work
ubi0: attaching mtd6
UBI: EOF marker found, PEBs from 74 will be erased
ubi0: scanning is finished
ubi0: volume 2 ("rootfs_data") re-sized from 9 to 1872 LEBs
ubi0: attached mtd6 (name "ubi", size 248 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 1988, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 17 32901136
ubi0: available PEBs: 0, total reserved PEBs: 1988, PEBs reserved for bad PEB ha ndling: 40
No size specified -> Using max size (4190208)
Read 4190208 bytes from volume kernel to 0000000046000000
## Loading kernel from FIT Image at 46000000 ...
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-6.6.63
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x460000e8
Data Size: 4109945 Bytes = 3.9 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x48000000
Entry Point: 0x48000000
Hash algo: crc32
Hash value: 3fc2f6cf
Hash algo: sha1
Hash value: 3f9e8d16ce876317e4638065fb4ca04834dabe54
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 46000000 ...
Using 'config-1' configuration
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt openembed_som7981 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x463eb8a8
Data Size: 22253 Bytes = 21.7 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: 322f3d8e
Hash algo: sha1
Hash value: ccd2388b00f6de5b41c08943fa91ec9146b80212
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x463eb8a8
Working FDT set to 463eb8a8
Uncompressing Kernel Image
Loading Device Tree to 000000007f7f2000, end 000000007f7fa6ec ... OK
Working FDT set to 7f7f2000
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 6.6.63 (builder@buildhost) (aarch64-openwrt-linux-m usl-gcc (OpenWrt GCC 13.3.0 r28158-d276b4c91a) 13.3.0, GNU ld (GNU Binutils) 2.4 2) #0 SMP Fri Nov 29 17:25:36 2024
[ 0.000000] Machine model: OpenEmbed SOM7981
[ 0.000000] OF: reserved mem: 0x0000000042ff0000..0x0000000042ffffff (64 KiB) map non-reusable ramoops@42ff0000
[ 0.000000] OF: reserved mem: 0x0000000043000000..0x000000004302ffff (192 KiB ) nomap non-reusable secmon@43000000
[ 0.000000] OF: reserved mem: 0x0000000047c80000..0x0000000047d7ffff (1024 Ki B) nomap non-reusable wmcpu-reserved@47c80000
[ 0.000000] OF: reserved mem: 0x0000000047d80000..0x0000000047dbffff (256 KiB ) nomap non-reusable wo-emi@47d80000
[ 0.000000] OF: reserved mem: 0x0000000047dc0000..0x0000000047ffffff (2304 Ki B) nomap non-reusable wo-data@47dc0000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff]
[ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff]
[ 0.000000] node 0: [mem 0x0000000043030000-0x0000000047c7ffff]
[ 0.000000] node 0: [mem 0x0000000047c80000-0x0000000047ffffff]
[ 0.000000] node 0: [mem 0x0000000048000000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.4
[ 0.000000] percpu: Embedded 18 pages/cpu s35560 r8192 d29976 u73728
[ 0.000000] pcpu-alloc: s35560 r8192 d29976 u73728 alloc=18*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: kernel page table isolation disabled by kernel conf iguration
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Kernel command line:
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, li near)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 1MB
[ 0.000000] software IO TLB: area num 2.
[ 0.000000] software IO TLB: mapped [mem 0x000000007fb29000-0x000000007fc2900 0] (1MB)
[ 0.000000] Memory: 1010832K/1048576K available (9024K kernel code, 996K rwda ta, 1664K rodata, 448K init, 307K bss, 37744K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jif fies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 640 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] Root IRQ handler: 0xffffffc080010080
[ 0.000000] GICv3: GICv3 features: 16 PPIs
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
[ 0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 43980 46511101ns
[ 0.000080] Calibrating delay loop (skipped), value calculated using timer fr equency.. 26.00 BogoMIPS (lpj=130000)
[ 0.000088] pid_max: default: 32768 minimum: 301
[ 0.003066] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, line ar)
[ 0.003077] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.005345] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.005896] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adju st=1 rcu_task_cpu_ids=2.
[ 0.006052] rcu: Hierarchical SRCU implementation.
[ 0.006055] rcu: Max phase no-delay instances is 1000.
[ 0.006474] smp: Bringing up secondary CPUs ...
[ 0.006848] Detected VIPT I-cache on CPU1
[ 0.006895] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000
[ 0.006928] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.007005] smp: Brought up 1 node, 2 CPUs
[ 0.007010] SMP: Total of 2 processors activated.
[ 0.007013] CPU features: detected: 32-bit EL0 Support
[ 0.007017] CPU features: detected: CRC32 instructions
[ 0.007051] CPU features: emulated: Privileged Access Never (PAN) using TTBR0 _EL1 switching
[ 0.007054] CPU: All CPU(s) started at EL2
[ 0.007056] alternatives: applying system-wide alternatives
[ 0.010809] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns
[ 0.010830] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.012113] pinctrl core: initialized pinctrl subsystem
[ 0.013207] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.013798] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.013830] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allo cations
[ 0.013852] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic al locations
[ 0.014245] thermal_sys: Registered thermal governor 'fair_share'
[ 0.014251] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.014254] thermal_sys: Registered thermal governor 'step_wise'
[ 0.014256] thermal_sys: Registered thermal governor 'user_space'
[ 0.014299] ASID allocator initialised with 65536 entries
[ 0.015234] pstore: Using crash dump compression: deflate
[ 0.015240] pstore: Registered ramoops as persistent store backend
[ 0.015242] ramoops: using 0x10000@0x42ff0000, ecc: 0
[ 0.022450] Modules: 29616 pages in range for non-PLT usage
[ 0.022459] Modules: 521136 pages in range for PLT usage
[ 0.023479] cryptd: max_cpu_qlen set to 1000
[ 0.024636] SCSI subsystem initialized
[ 0.024878] libata version 3.00 loaded.
[ 0.026482] clocksource: Switched to clocksource arch_sys_counter
[ 0.028817] NET: Registered PF_INET protocol family
[ 0.028954] IP idents hash table entries: 16384 (order: 5, 131072 bytes, line ar)
[ 0.030737] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.030759] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.030770] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.030822] TCP bind hash table entries: 8192 (order: 6, 262144 bytes, linear )
[ 0.031021] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.031408] MPTCP token hash table entries: 1024 (order: 2, 24576 bytes, line ar)
[ 0.031542] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.031575] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.031878] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.031905] PCI: CLS 0 bytes, default 64
[ 0.033311] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[ 0.038250] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.038260] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc.
[ 0.071965] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 51)
[ 0.083436] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.087461] printk: console [ttyS0] disabled
[ 0.107858] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 72, base_baud = 2500000) is a ST16650V2
[ 0.107904] printk: console [ttyS0] enabled
[ 0.855628] loop: module loaded
[ 0.861118] spi-nand spi0.0: Winbond SPI NAND was found.
[ 0.866432] spi-nand spi0.0: 256 MiB, block size: 128 KiB, page size: 2048, O OB size: 128
[ 0.875290] 6 fixed-partitions partitions found on MTD device spi0.0
[ 0.881797] Creating 6 MTD partitions on "spi0.0":
[ 0.886603] 0x000000000000-0x000000100000 : "bl2"
[ 0.892379] 0x000000100000-0x000000180000 : "u-boot-env"
[ 0.898524] 0x000000180000-0x000000280000 : "factory"
[ 0.904875] 0x000000280000-0x000000380000 : "config"
[ 0.910899] 0x000000380000-0x000000580000 : "fip"
[ 0.917195] 0x000000580000-0x00000fe00000 : "ubi"
[ 1.178413] mtk_soc_eth 15100000.ethernet: generated random MAC address 65:74 :68:25:64:00
[ 1.186819] mtk_soc_eth 15100000.ethernet: generated random MAC address 65:74 :68:25:64:00
[ 1.299882] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xff ffffc081680000, irq 75
[ 1.309855] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xff ffffc081680000, irq 75
[ 1.319649] i2c_dev: i2c /dev entries driver
[ 1.325863] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowa yout=0)
[ 1.335093] NET: Registered PF_INET6 protocol family
[ 1.341281] Segment Routing with IPv6
[ 1.344971] In-situ OAM (IOAM) with IPv6
[ 1.348963] NET: Registered PF_PACKET protocol family
[ 1.354030] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.367366] 8021q: 802.1Q VLAN Support v1.8
[ 1.396374] phy phy-soc:usb-phy@11e10000.1: type_sw - reg 0x218, index 0
[ 1.404451] UBI: auto-attach mtd5
[ 1.407798] ubi0: default fastmap pool size: 95
[ 1.412319] ubi0: default fastmap WL pool size: 47
[ 1.417126] ubi0: attaching mtd5
[ 1.896498] random: crng init done
[ 2.127866] ubi0: scanning is finished
[ 2.137092] ubi0 warning: 0xffffffc0805d2968: cannot reserve enough PEBs for bad PEB handling, reserved 38, need 40
[ 2.148580] ubi0: attached mtd5 (name "ubi", size 248 MiB)
[ 2.154073] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 2.160953] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 2.167737] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 2.174685] ubi0: good PEBs: 1988, bad PEBs: 0, corrupted PEBs: 0
[ 2.180769] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 12 8
[ 2.187981] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequ ence number: 1732901136
[ 2.197101] ubi0: available PEBs: 0, total reserved PEBs: 1988, PEBs reserved for bad PEB handling: 38
[ 2.206405] ubi0: background thread "ubi_bgt0d" started, PID 591
[ 2.213090] block ubiblock0_1: created from ubi0:1(rootfs)
[ 2.218607] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 2.225669] clk: Disabling unused clocks
[ 2.234656] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 2.241980] Freeing unused kernel memory: 448K
[ 2.246559] Run /sbin/init as init process
[ 2.250648] with arguments:
[ 2.253601] /sbin/init
[ 2.256295] with environment:
[ 2.259437] HOME=/
[ 2.261785] TERM=linux
[ 2.435999] init: Console is alive
[ 2.439633] init: - watchdog -
[ 2.845252] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.876712] usbcore: registered new interface driver usbfs
[ 2.882253] usbcore: registered new interface driver hub
[ 2.887649] usbcore: registered new device driver usb
[ 2.893438] gpio_button_hotplug: loading out-of-tree module taints kernel.
[ 2.905443] xhci-mtk 11200000.usb: supply vbus not found, using dummy regulat or
[ 2.913614] xhci-mtk 11200000.usb: xHCI Host Controller
[ 2.918951] xhci-mtk 11200000.usb: new USB bus registered, assigned bus numbe r 1
[ 2.929348] xhci-mtk 11200000.usb: hcc params 0x01403f99 hci version 0x110 qu irks 0x0000000000200010
[ 2.938594] xhci-mtk 11200000.usb: irq 79, io mem 0x11200000
[ 2.944351] xhci-mtk 11200000.usb: xHCI Host Controller
[ 2.949586] xhci-mtk 11200000.usb: new USB bus registered, assigned bus numbe r 2
[ 2.956983] xhci-mtk 11200000.usb: Host supports USB 3.2 Enhanced SuperSpeed
[ 2.964514] hub 1-0:1.0: USB hub found
[ 2.968407] hub 1-0:1.0: 1 port detected
[ 2.972736] usb usb2: We don't know the algorithms for LPM for this host, dis abling LPM.
[ 2.981306] hub 2-0:1.0: USB hub found
[ 2.985098] hub 2-0:1.0: 1 port detected
[ 2.993992] kmodloader: done loading kernel modules from /etc/modules-boot.d/ *
[ 3.011333] init: - preinit -
[ 3.456510] mtk_soc_eth 15100000.ethernet eth0: validation of with support 0 0,00000000,00000000,00006000 and advertisement 00,00000000,00000000,00000000 fai led: -EINVAL
[ 3.506495] mtk_soc_eth 15100000.ethernet eth0: mtk_open: could not attach PH Y: -22
ip: SIOCSIFFLAGS: Invalid argument
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 7.726336] UBIFS (ubi0:2): default file-system created
[ 7.731950] UBIFS (ubi0:2): Mounting in unauthenticated mode
[ 7.737704] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 754
[ 7.772747] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "root fs_data"
[ 7.780599] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O u nit sizes: 2048 bytes/2048 bytes
[ 7.790507] UBIFS (ubi0:2): FS size: 236175360 bytes (225 MiB, 1860 LEBs), ma x 1872 LEBs, journal size 11808768 bytes (11 MiB, 93 LEBs)
[ 7.802669] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB)
[ 7.809273] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 6A45C F67-29BA-43D9-BC39-5D5A68520311, small LPT model
[ 7.822036] mount_root: overlay filesystem has not been fully initialized yet
[ 7.829507] mount_root: switching to ubifs overlay
[ 7.836863] overlayfs: null uuid detected in lower fs '/', falling back to xi no=off,index=off,nfs_export=off.
[ 7.848837] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 7.899973] procd: - early -
[ 7.902925] procd: - watchdog -
[ 8.462752] procd: - watchdog -
[ 8.466362] procd: - ubus -
[ 8.622536] procd: - init -
Please press Enter to activate this console.
[ 8.959536] kmodloader: loading kernel modules from /etc/modules.d/*
[ 8.983593] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5 ),PE:150/433(alg:7fcdfc00)/0/0/0
[ 9.001438] Loading modules backported from Linux version v6.11.2-0-g7aa21fec 187b
[ 9.008963] Backport generated by backports.git v6.1.110-1-32-gc61f71fe0942
[ 9.162274] urngd: v1.0.2 started.
[ 9.438251] mt798x-wmac 18000000.wifi: HW/SW Version: 0x8a108a10, Build Time: 20240823161240a
[ 9.438251]
[ 9.616219] mt798x-wmac 18000000.wifi: WM Firmware Version: ____000000, Build Time: 20240823161304
[ 9.708935] mt798x-wmac 18000000.wifi: WA Firmware Version: DEV_000000, Build Time: 20240823161841
[ 9.805904] mt798x-wmac 18000000.wifi: eeprom load fail, use default bin
[ 9.812714] mt798x-wmac 18000000.wifi: Direct firmware load for mediatek/mt79 81_eeprom_mt7976_dbdc.bin failed with error -2
[ 9.823852] mt798x-wmac 18000000.wifi: Falling back to sysfs fallback for: me diatek/mt7981_eeprom_mt7976_dbdc.bin
[ 9.896208] mt798x-wmac: probe of 18000000.wifi failed with error -12
[ 9.927113] PPP generic driver version 2.4.2
[ 9.932620] NET: Registered PF_PPPOX protocol family
[ 9.941603] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 15.868351] mtk_soc_eth 15100000.ethernet eth1: PHY [mdio-bus:00] driver [Med iaTek MT7981 PHY] (irq=POLL)
[ 15.883753] mtk_soc_eth 15100000.ethernet eth1: configuring for phy/gmii link mode
[ 15.893928] br-lan: port 1(eth1) entered blocking state
[ 15.899258] br-lan: port 1(eth1) entered disabled state
[ 15.904528] mtk_soc_eth 15100000.ethernet eth1: entered allmulticast mode
[ 15.911604] mtk_soc_eth 15100000.ethernet eth1: entered promiscuous mode
[ 16.076568] mtk_soc_eth 15100000.ethernet eth0: validation of with support 0 0,00000000,00000000,00006000 and advertisement 00,00000000,00000000,00000000 fai led: -EINVAL
[ 16.156555] mtk_soc_eth 15100000.ethernet eth0: mtk_open: could not attach PH Y: -22
[ 17.996697] mtk_soc_eth 15100000.ethernet eth1: Link is Up - 100Mbps/Full - f low control rx/tx
[ 17.996742] br-lan: port 1(eth1) entered blocking state
[ 18.010535] br-lan: port 1(eth1) entered forwarding state
[ 50.236630] mtk_soc_eth 15100000.ethernet eth1: Link is Down
[ 50.243207] br-lan: port 1(eth1) entered disabled state
wan port not working etheir
i flash https://anduin.linuxfromscratch.org/sources/linux-firmware/mediatek/
mt7986_eeprom_mt7976_dbdc.bin and wifi work now wan what i do
It looks like there is a little Realtek chip near the wan port. That could be a separate PHY for the wan. If the model you're working from (1698?) doesn't have the same hardware you will need to make sure your build has the driver for that chip and also activate it in the DTS file.
can you tell what to do?
Please build an image which includes mdio-tools, this will allow you to scan the MDIO bus and see which exact type of PHY we are dealing with and what is the address you need to put into the device tree.
Try
mdio mdio-bus
This should show you the built-in PHY of the MT7981 SoC on address 0 and another PHY (RealTek is 001c...., for example) on another address. Once we know the ID and the address, you can put that into device tree and it should work.
root@OpenWrt:~#
root@OpenWrt:~# mdio mdio-bus
DEV PHY-ID LINK
0x00 0x03a29461 up
0x01 0x00000000 down
0x02 0x00000000 down
0x03 0x00000000 down
0x04 0x00000000 down
0x05 0x00000000 down
0x06 0x001cc849 down
0x07 0x00000000 down
0x08 0x00000000 down
0x09 0x00000000 down
0x0a 0x00000000 down
0x0b 0x00000000 down
0x0c 0x00000000 down
0x0d 0x00000000 down
0x0e 0x00000000 down
0x0f 0x00000000 down
0x10 0x00000000 down
0x11 0x00000000 down
0x12 0x00000000 down
0x13 0x00000000 down
0x14 0x00000000 down
0x15 0x00000000 down
0x16 0x00000000 down
0x17 0x00000000 down
0x18 0x00000000 down
0x19 0x00000000 down
0x1a 0x00000000 down
0x1b 0x00000000 down
0x1c 0x00000000 down
0x1d 0x00000000 down
0x1e 0x00000000 down
0x1f 0x00000000 down
0x06 0x001cc849 up wan port
what now?
every time update i loss wifi untill put frimware files
mt7986_eeprom_mt7976_dbdc.bin how to config this permanently
So now we know that we got a RealTek RTL8221B-VB-CG at MDIO address 6.
The next step is to find the PHY reset GPIO. Almost all MT7981 boards use GPIO 39 as reset. You can try by exporting that GPIO to sysfs and see if toggling it's value makes the PHY disappear in mdio mdio-bus output:
cd /sys/class/gpio
gn=$(( 512 + 39 ))
echo $gn > export
cd gpio$gn
echo out > direction
echo 0 > value
# no see if PHY 0x001cc849 disappeared and on DEV 0x6 you should see 0x00000000
mdio mdio-bus
echo 1 > value
# check again
mdio mdio-bus
If the PHY does not disappear ever during this procedure you need to try other GPIOs than 39, eg. 3, 5, 12 or 14 are other popular choices.
If you can download the stock firmware from somewhere this can also help, either by extracting the Device Tree from it or by running it and inspecting at runtime via cat /sys/kernel/debug/gpio which GPIOs are in use. Apart from the PHY reset GPIO you may also want to find out about PHY interrupt, buttons and LEDs, maybe power and reset for the mPCIe and M.2 socket.
1 Like
The fact that the WiFi driver requests this file means that it is lacking WiFi EEPROM data. Typically this data (calibration specific for the board and antennas as well as MAC addresses) is kept in a dedicated MTD partition or UBI volume. The best is to run the stock firmware and follow the boot log to find out about the names of MTD partitions. If there is a partition called factory, art bdinfo or eeprom that's usually where to find this data.
Once you found out, you need to tell the driver to load the firmware from there. This is done by introducing nvmem-layout to the MTD partition or UBI volume, and referencing it using nvmem-cells for the WiFi driver. See the dts of any other MT7981 board, there are plenty of examples.
i wiped everything there was factory
Then you’re out of luck.
With no calibration data you can’t get the wifi to function.
Okee dokee, sorry for kinda ghosting after reaching out. Had some RLBS to deal with. However I did manage to finally track down and sweet talk the oem into giving me a complete firmware image. 212.5MB gz if anyone wants to try there hand at un-fk'n it. I'll see about posting a google drive link once I get it UL'd
Update - Current fw image direct from Huasifei; zx7981-sdk-open.tar.gz https://drive.google.com/file/d/1UIQa0nRibHRExh-0S55M9U3KwP7R8wsb/view?usp=sharing
gpiochip0: GPIOs 455-511, parent: platform/11d00000.pinctrl, pinctrl_moore:
gpio-455 ( |wps ) in lo ACTIVE LOW
gpio-456 ( |reset ) in hi ACTIVE LOW
gpio-459 ( |5greset ) out lo ACTIVE LOW
gpio-460 ( |5gpower ) out hi ACTIVE LOW
gpio-461 ( |lede:blue:4g ) out lo ACTIVE LOW
gpio-462 ( |lede:blue:5g ) out hi ACTIVE LOW
gpio-463 ( |lede:blue:lan ) out hi ACTIVE LOW
gpio-464 ( |lede:blue:sim2 ) out lo ACTIVE LOW
gpio-465 ( |lede:blue:wifi ) out lo ACTIVE LOW
gpio-466 ( |lede:blue:sim1 ) out hi ACTIVE LOW
gpio-485 ( |ws222-scl ) out lo
gpio-486 ( |ws222-sda ) out hi
stock fw
add support to ws1610
i need to know how to get flash layout
i used mt3000 layout beacuse i dont know how get it
Just noticed ROOter autobuilds just posted 2 builds for the ws1610 on the 6th and a new one yesterday. Just fyi
1 Like