Has anyone tried the MSM460 instructions/bootloader on the MSM466? (looks like same hardware but with RP SMA ). (edit: MSM460 also has two dual band radios but limited in software per checking another thread)
Starting a thread as I should have a number of units coming in the hope of getting them working on OpenWrt.
Cheers.
What hardware are you talking about? Deskjet? Probook?
Thanks for reaching out.
It's in the same family as this:
https://openwrt.org/toh/hwdata/hpe/hpe_msm460
My teardown for the MSM466 on WikiDevi page shows the only difference is the antennas.
Probably read 10 years old news. Got fcc id to locate official pictures?
Thanks Yeah after looking closely the board numbers appear to be the same. (edit: clarifying, between the ones uploaded to WikiDevi)
Can you get FCC ID from the unit?
I guess see WikiDevi?
I'll report back on further info once I have the units in hand and give it a go myself. Probably next week given interstate shipping though =(
OK, heads up then.
would be great to get this merged: https://github.com/openwrt/openwrt/pull/16248
So it is same with reversed plugs?
Looks like that's just changing the DTS for MSM460.
Good to have that pointed out for when I do my test builds though.
Looks like this sets the mac address in the DTS rather than in hotplug.d in userspace. As well as moving LED pin definitions? Nothing to do with MSM466 support specifically?
You stand a stronger chance of getting your changes merged if you add submit description and the Signed-off-by: tag. See https://openwrt.org/submitting-patches#submission_guidelines.
Hi All.
So I tried the MSM460 instructions on the MSM466 and was successful.
Of note is Colubris_BID has the board number in it at 0x197. (J9622-6001, i.e. j9622-WW in my case). From what I think that means, to add this device properly I would need to do some detection and select the device tree in the bootloader?
Flashing ended up dropping the max transmit power in 5ghz? I ended up from 20dbm max (both bands) in factory with a 2dbi antenna set to 17-18dbM in 5ghz and 22dBm max in 2.4 at least as reported by iw phy0 info and iw phy1 info
I don't know how max transmit power is set, nor how to set antenna gain and will have to look into.
I'll be working on a quick patch to get the board name right first. i.e. user decides which firmware to use?
Also of note is that it's 115200 baud rate as per the default in the factory firmware. not 9600 like it is on the TOH
As an aside:
I was getting gibberish on my USB converters which worked fine with other 115200 devices but using a proper hardware one in a desktop worked fine.
Posting bootlog as I haven't seen an MSM460/MSM466 bootlog posted anywhere where it has been flashed to openwrt? No wiki page yet? Not sure whether I should create one yet.
Also modified the wiki page for 115200 per the device tree.
NAND boot...
Second program loader running in sram...transfering control
WARNING: Calling __hwconfig without a buffer and before environment is ready
WARNING: Calling __hwconfig without a buffer and before environment is ready
Tertiary program loader running in sram...transfering control
U-Boot 2014.04-00001-g4d68b09daa (May 28 2024 - 22:56:30)
CPU0: P1020E, Version: 1.1, (0x80ec0011)
Core: e500, Version: 5.1, (0x80212051)
Clock Configuration:
CPU0:800 MHz, CPU1:800 MHz,
CCB:400 MHz,
DDR:333.333 MHz (666.667 MT/s data rate) (Asynchronous), LBC:50 MHz
L1: D-cache 32 KiB enabled
I-cache 32 KiB enabled
Board: HP MSM460
I2C: ready
SPI: ready
DRAM: 256 MiB (DDR3, 32-bit, CL=5, ECC off)
L2: 256 KiB already enabled
NAND: 128 MiB
*** Warning - bad CRC, using default environment
PCIe1: Root Complex of mini PCIe SLOT, x1 gen1, regs @ 0xffe0a000
01:00.0 - 168c:0030 - Network controller
PCIe1: Bus 00 - 01
PCIe2: Root Complex of PCIe SLOT, x1 gen1, regs @ 0xffe09000
03:00.0 - 168c:0030 - Network controller
PCIe2: Bus 02 - 03
In: serial
Out: serial
Err: serial
Net: eTSEC1 [PRIME]
Hewlett-Packard MSM460 Pre-Boot
NAND read: device 0 offset 0xc0000, size 0x40000
262144 bytes read: OK
Ethernet MAC address: 14:58:d0:67:29:d3
WLAN MAC address: 50:65:f3:db:57:20
Device IP-Address: 192.168.1.111
Press reset button to enter recovery mode...
Press reset button for 5 seconds.
Reset button not pressed, continuing boot...
Hit any key to stop autoboot: 0
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=5"
UBI: MTD device size: 95 MiB
UBI: number of good PEBs: 760
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 3
UBI: available PEBs: 13
UBI: total number of reserved PEBs: 747
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 2/0
Read 0 bytes from volume kernel to 4000000
No size specified -> Using max size (3174400)
## Loading kernel from FIT Image at 04000000 ...
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: POWERPC OpenWrt Linux-5.15.162
Created: 2024-07-15 22:14:18 UTC
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x040000ec
Data Size: 3084429 Bytes = 2.9 MiB
Architecture: PowerPC
OS: Linux
Load Address: 0x00000000
Entry Point: 0x00000000
Hash algo: crc32
Hash value: 2fa15725
Hash algo: sha1
Hash value: cd65e38b9e7f2615420ad26794f368d895ecebcf
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 04000000 ...
Using 'config-1' configuration
Trying 'fdt-1' fdt subimage
Description: POWERPC OpenWrt hpe_msm460 device tree blob
Created: 2024-07-15 22:14:18 UTC
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x042f12b8
Data Size: 11456 Bytes = 11.2 KiB
Architecture: PowerPC
Hash algo: crc32
Hash value: c5c6f75a
Hash algo: sha1
Hash value: e0f016e96402513cbca8ec5dcac1c3595e6738d2
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x42f12b8
Uncompressing Kernel Image ... OK
Loading Device Tree to 02ffa000, end 02fffcbf ... OK
[ 0.000000] Memory CAM mapping: 256 Mb, residual: 0Mb
[ 0.000000] Linux version 5.15.162 (builder@buildhost) (powerpc-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r24012-d8dd03c46f) 12.3.0, GNU4
[ 0.000000] Using P1020 RDB machine description
[ 0.000000] printk: bootconsole [udbg0] enabled
[ 0.000000] CPU maps initialized for 1 thread per core
[ 0.000000] -----------------------------------------------------
[ 0.000000] phys_mem_size = 0x10000000
[ 0.000000] dcache_bsize = 0x20
[ 0.000000] icache_bsize = 0x20
[ 0.000000] cpu_features = 0x0000000010010108
[ 0.000000] possible = 0x0000000010010108
[ 0.000000] always = 0x0000000010010108
[ 0.000000] cpu_user_features = 0x84e08000 0x08000000
[ 0.000000] mmu_features = 0x00020010
[ 0.000000] -----------------------------------------------------
msm_setup_arch()
[ 0.000000] ioremap() called early from 0xc083a3dc. Use early_ioremap() instead
[ 0.000000] MSM460 board from HPE
[ 0.000000] barrier-nospec: using isync; sync as speculation barrier
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[ 0.000000] percpu: Embedded 11 pages/cpu s15820 r8192 d21044 u45056
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,115200 ubi.mtd=5,2048
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xffbdf000..0xfffff000 : fixmap
[ 0.000000] * 0xffbdd000..0xffbdf000 : early ioremap
[ 0.000000] * 0xd1000000..0xffbdd000 : vmalloc & ioremap
[ 0.000000] Memory: 249900K/262144K available (7476K kernel code, 660K rwdata, 916K rodata, 228K init, 236K bss, 12244K reserved, 0K cma-)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 512, nr_irqs: 512, preallocated irqs: 16
[ 0.000000] mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000, max 2 CPUs
[ 0.000000] mpic: ISU size: 256, shift: 8, mask: ff
[ 0.000000] mpic: Initializing for 256 sources
[ 0.000006] clocksource: timebase: mask: 0xffffffffffffffff max_cycles: 0xb8812736b, max_idle_ns: 440795202655 ns
[ 0.010179] clocksource: timebase mult[14000000] shift[24] registered
[ 0.016727] pid_max: default: 32768 minimum: 301
[ 0.021895] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.029165] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.038604] mpic: requesting IPIs...
[ 0.043941] rcu: Hierarchical SRCU implementation.
[ 0.049350] smp: Bringing up secondary CPUs ...
[ 0.055123] smp: Brought up 1 node, 2 CPUs
[ 0.062194] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.071999] futex hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.080325] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.087132] thermal_sys: Registered thermal governor 'step_wise'
[ 0.097693] Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->1
[ 0.111560] PCI host bridge /pcie@ffe09000 (primary) ranges:
[ 0.117181] MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000
[ 0.124395] IO 0x00000000ffc10000..0x00000000ffc1ffff -> 0x0000000000000000
[ 0.131528] /pcie@ffe09000: PCICSRBAR @ 0xfff00000
[ 0.136287] setup_pci_atmu: end of DRAM 10000000
[ 0.141534] Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->1
[ 0.149409] PCI host bridge /pcie@ffe0a000 ranges:
[ 0.154251] MEM 0x0000000080000000..0x000000009fffffff -> 0x0000000080000000
[ 0.161464] IO 0x00000000ffc00000..0x00000000ffc0ffff -> 0x0000000000000000
[ 0.168595] /pcie@ffe0a000: PCICSRBAR @ 0xfff00000
[ 0.173375] setup_pci_atmu: end of DRAM 10000000
[ 0.181459] PCI: Probing PCI hardware
[ 0.185214] fsl-pci ffe09000.pcie: PCI host bridge to bus 0000:00
[ 0.191231] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.197424] pci_bus 0000:00: root bus resource [mem 0xa0000000-0xbfffffff]
[ 0.204251] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.209735] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to ff
[ 0.216353] pci 0000:00:00.0: [1957:0100] type 01 class 0x060400
[ 0.222338] pci 0000:00:00.0: reg 0x10: [mem 0xfff00000-0xffffffff]
[ 0.228617] pci 0000:00:00.0: supports D1 D2
[ 0.232829] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.240715] pci 0000:01:00.0: [168c:0030] type 00 class 0x028000
[ 0.246728] pci 0000:01:00.0: reg 0x10: [mem 0xa0000000-0xa001ffff 64bit]
[ 0.253478] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.260249] pci 0000:01:00.0: supports D1
[ 0.264179] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[ 0.301126] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.306289] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 0.312402] pci 0000:00:00.0: bridge window [mem 0xa0000000-0xa00fffff]
[ 0.319145] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.325755] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[ 0.332583] fsl-pci ffe0a000.pcie: PCI host bridge to bus 0001:02
[ 0.338637] pci_bus 0001:02: root bus resource [io 0x20000-0x2ffff] (bus address [0x0000-0xffff])
[ 0.347539] pci_bus 0001:02: root bus resource [mem 0x80000000-0x9fffffff]
[ 0.354415] pci_bus 0001:02: root bus resource [bus 02-ff]
[ 0.359866] pci_bus 0001:02: busn_res: [bus 02-ff] end is updated to ff
[ 0.366518] pci 0001:02:00.0: [1957:0100] type 01 class 0x060400
[ 0.372463] pci 0001:02:00.0: reg 0x10: [mem 0xfff00000-0xffffffff]
[ 0.378811] pci 0001:02:00.0: supports D1 D2
[ 0.383003] pci 0001:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.390781] pci 0001:02:00.0: Primary bus is hard wired to 0
[ 0.396365] pci 0001:02:00.0: bridge configuration invalid ([bus 01-01]), reconfiguring
[ 0.404564] pci 0001:03:00.0: [168c:0030] type 00 class 0x028000
[ 0.410519] pci 0001:03:00.0: reg 0x10: [mem 0x80000000-0x8001ffff 64bit]
[ 0.417337] pci 0001:03:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.424059] pci 0001:03:00.0: supports D1
[ 0.428007] pci 0001:03:00.0: PME# supported from D0 D1 D3hot
[ 0.458984] pci 0001:02:00.0: PCI bridge to [bus 03-ff]
[ 0.464147] pci 0001:02:00.0: bridge window [io 0x20000-0x20fff]
[ 0.470435] pci 0001:02:00.0: bridge window [mem 0x80000000-0x800fffff]
[ 0.477177] pci_bus 0001:03: busn_res: [bus 03-ff] end is updated to 03
[ 0.483787] pci_bus 0001:02: busn_res: [bus 02-ff] end is updated to 03
[ 0.490485] PCI: Cannot allocate resource region 0 of device 0000:00:00.0, will remap
[ 0.498277] PCI: Cannot allocate resource region 0 of device 0001:02:00.0, will remap
[ 0.506107] pci 0000:00:00.0: BAR 0: no space for [mem size 0x00100000]
[ 0.512670] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x00100000]
[ 0.519600] pci 0000:01:00.0: BAR 6: assigned [mem 0xa0020000-0xa002ffff pref]
[ 0.526817] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.531745] pci 0000:00:00.0: bridge window [io 0x0000-0xffff]
[ 0.537857] pci 0000:00:00.0: bridge window [mem 0xa0000000-0xbfffffff]
[ 0.544592] pci_bus 0000:00: Some PCI device resources are unassigned, try booting with pci=realloc
[ 0.553639] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
[ 0.559170] pci_bus 0000:00: resource 5 [mem 0xa0000000-0xbfffffff]
[ 0.565436] pci_bus 0000:01: resource 0 [io 0x0000-0xffff]
[ 0.570975] pci_bus 0000:01: resource 1 [mem 0xa0000000-0xbfffffff]
[ 0.577253] pci 0001:02:00.0: BAR 0: no space for [mem size 0x00100000]
[ 0.583822] pci 0001:02:00.0: BAR 0: failed to assign [mem size 0x00100000]
[ 0.590796] pci 0001:03:00.0: BAR 6: assigned [mem 0x80020000-0x8002ffff pref]
[ 0.597972] pci 0001:02:00.0: PCI bridge to [bus 03]
[ 0.602941] pci 0001:02:00.0: bridge window [io 0x20000-0x2ffff]
[ 0.609170] pci 0001:02:00.0: bridge window [mem 0x80000000-0x9fffffff]
[ 0.615976] pci_bus 0001:02: Some PCI device resources are unassigned, try booting with pci=realloc
[ 0.624966] pci_bus 0001:02: resource 4 [io 0x20000-0x2ffff]
[ 0.630716] pci_bus 0001:02: resource 5 [mem 0x80000000-0x9fffffff]
[ 0.636944] pci_bus 0001:03: resource 0 [io 0x20000-0x2ffff]
[ 0.642686] pci_bus 0001:03: resource 1 [mem 0x80000000-0x9fffffff]
[ 0.660876] EDAC MC: Ver: 3.0.0
[ 0.665921] clocksource: Switched to clocksource timebase
[ 0.672586] NET: Registered PF_INET protocol family
[ 0.677628] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.685618] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.693951] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.701654] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.709326] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.716440] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.722852] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.729368] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.736605] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.742270] PCI: CLS 32 bytes, default 32
[ 0.748950] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.760628] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.766466] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.777386] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.786236] pcieport 0000:00:00.0: enabling device (0106 -> 0107)
[ 0.792522] pcieport 0001:02:00.0: enabling device (0106 -> 0107)
[ 0.799103] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.807915] printk: console [ttyS0] disabled
[ 0.812154] serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42, base_baud = 24999999) is a 16550A
[ 0.820867] printk: console [ttyS0] enabled
[ 0.820867] printk: console [ttyS0] enabled
[ 0.829173] printk: bootconsole [udbg0] disabled
[ 0.829173] printk: bootconsole [udbg0] disabled
[ 0.838679] serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42, base_baud = 24999999) is a 16550A
[ 0.848003] printk: console [ttyS0] disabled
[ 0.852411] printk: console [ttyS0] enabled
[ 0.857195] ffe04600.serial: ttyS1 at MMIO 0xffe04600 (irq = 42, base_baud = 24999999) is a 16550
[ 0.869188] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xa1
[ 0.875558] nand: Micron MT29F1G08ABBDAHC
[ 0.879673] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.887802] Bad block table found at page 65472, version 0x01
[ 0.894330] Bad block table found at page 65408, version 0x01
[ 0.901367] 9 fixed-partitions partitions found on MTD device ff800000.flash
[ 0.908482] Creating 9 MTD partitions on "ff800000.flash":
[ 0.914014] 0x000000000000-0x0000000c0000 : "u-boot"
[ 0.919994] 0x0000000c0000-0x000000100000 : "colubris-bid"
[ 0.926606] 0x000000100000-0x000000180000 : "uboot-env0"
[ 0.932647] 0x000000180000-0x000000200000 : "uboot-env1"
[ 0.939227] 0x000000200000-0x000000500000 : "reserved"
[ 0.945505] 0x000000500000-0x000006400000 : "ubi"
[ 0.951305] 0x000006500000-0x000006900000 : "pool"
[ 0.956848] 0x000006900000-0x000007ee0000 : "flash"
[ 0.962549] 0x000007ee0000-0x000007f00000 : "pf"
[ 0.972111] eLBC NAND device at 0xff800000, bank 0
[ 0.977987] fsl_espi ffe07000.spi: irq = 59
[ 1.028717] fsl-gianfar soc@ffe00000:ethernet@b0000: enabled errata workarounds, flags: 0x4
[ 1.047996] fsl-gianfar soc@ffe00000:ethernet@b0000 eth0: mac: 14:58:d0:67:29:d3
[ 1.055420] fsl-gianfar soc@ffe00000:ethernet@b0000 eth0: Running with NAPI enabled
[ 1.063112] fsl-gianfar soc@ffe00000:ethernet@b0000 eth0: RX BD ring size for Q[0]: 256
[ 1.071140] fsl-gianfar soc@ffe00000:ethernet@b0000 eth0: RX BD ring size for Q[1]: 256
[ 1.079166] fsl-gianfar soc@ffe00000:ethernet@b0000 eth0: TX BD ring size for Q[0]: 256
[ 1.087193] fsl-gianfar soc@ffe00000:ethernet@b0000 eth0: TX BD ring size for Q[1]: 256
[ 1.095453] ucc_geth_driver: QE UCC Gigabit Ethernet Controller
[ 1.101817] i2c_dev: i2c /dev entries driver
[ 1.106416] mpc-i2c ffe03100.i2c: timeout 1000000 us
[ 1.111929] booke_wdt: powerpc book-e watchdog driver loaded
[ 1.117881] Freescale(R) MPC85xx EDAC driver, (C) 2006 Montavista Software
[ 1.124985] fsl_mc_err_probe: No ECC DIMMs discovered
[ 1.130890] EDAC DEVICE0: Giving out device to module MPC85xx_edac controller mpc85xx_l2_err: DEV mpc85xx_l2_err (INTERRUPT)
[ 1.142366] MPC85xx_edac acquired irq 16 for L2 Err
[ 1.147298] MPC85xx_edac L2 err registered
[ 1.151989] EDAC PCI0: Giving out device to module MPC85xx_edac controller mpc85xx_pci_err: DEV mpc85xx-pci-edac.0.auto (INTERRUPT)
[ 1.163915] MPC85xx_edac acquired irq 16 for PCI Err
[ 1.168920] MPC85xx_edac PCI err registered
[ 1.173297] EDAC PCI1: Giving out device to module MPC85xx_edac controller mpc85xx_pci_err: DEV mpc85xx-pci-edac.1.auto (INTERRUPT)
[ 1.185206] MPC85xx_edac acquired irq 16 for PCI Err
[ 1.190210] MPC85xx_edac PCI err registered
[ 1.195580] NET: Registered PF_INET6 protocol family
[ 1.202425] Segment Routing with IPv6
[ 1.206231] In-situ OAM (IOAM) with IPv6
[ 1.210241] NET: Registered PF_PACKET protocol family
[ 1.215397] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you nee.
[ 1.228856] 8021q: 802.1Q VLAN Support v1.8
[ 1.233124] drmem: No dynamic reconfiguration memory found
[ 1.241327] ubi0: attaching mtd5
[ 1.691834] ubi0: scanning is finished
[ 1.704344] ubi0: attached mtd5 (name "ubi", size 95 MiB)
[ 1.709819] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.716730] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[ 1.723437] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.730418] ubi0: good PEBs: 760, bad PEBs: 0, corrupted PEBs: 0
[ 1.736451] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 1.743677] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1721081658
[ 1.752830] ubi0: available PEBs: 0, total reserved PEBs: 760, PEBs reserved for bad PEB handling: 20
[ 1.762134] ubi0: background thread "ubi_bgt0d" started, PID 252
[ 1.763282] block ubiblock0_1: created from ubi0:1(rootfs)
[ 1.773725] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 1.785410] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 1.793101] Freeing unused kernel image (initmem) memory: 228K
[ 1.799023] This architecture does not have kernel memory protection.
[ 1.805479] Run /sbin/init as init process
[ 2.100787] init: Console is alive
[ 2.104592] init: - watchdog -
[ 2.685190] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.732176] usbcore: registered new interface driver usbfs
[ 2.737829] usbcore: registered new interface driver hub
[ 2.743228] usbcore: registered new device driver usb
[ 2.751709] Button Hotplug driver version 0.4.1
[ 2.758161] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.765613] fsl-ehci: Freescale EHCI Host controller driver
[ 2.772207] ehci-platform: EHCI generic platform driver
[ 2.782805] input: buttons as /devices/platform/buttons/input/input0
[ 2.790142] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 2.805152] init: - preinit -
[ 3.410851] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.560468] UBIFS (ubi0:2): Mounting in unauthenticated mode
[ 5.566459] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 371
[ 5.602894] UBIFS (ubi0:2): recovery needed
[ 5.683139] UBIFS (ubi0:2): recovery completed
[ 5.687756] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 5.695615] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 5.705566] UBIFS (ubi0:2): FS size: 84819968 bytes (80 MiB, 668 LEBs), max 679 LEBs, journal size 4190208 bytes (3 MiB, 33 LEBs)
[ 5.717250] UBIFS (ubi0:2): reserved for root: 4006256 bytes (3912 KiB)
[ 5.723870] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID E2405C8B-AD47-4E06-8256-1EE70FCAFD61, small LPT model
[ 5.738550] mount_root: switching to ubifs overlay
[ 5.754358] urandom-seed: Seeding with /etc/urandom.seed
[ 5.892908] procd: - early -
[ 5.896086] procd: - watchdog -
[ 6.488118] procd: - watchdog -
[ 6.492010] procd: - ubus -
[ 6.538301] random: ubusd: uninitialized urandom read (4 bytes read)
[ 6.547562] random: ubusd: uninitialized urandom read (4 bytes read)
[ 6.554340] random: ubusd: uninitialized urandom read (4 bytes read)
[ 6.566575] procd: - init -
Please press Enter to activate this console.
[ 7.042877] kmodloader: loading kernel modules from /etc/modules.d/*
[ 7.264356] Loading modules backported from Linux version v6.1.97-0-g7753af06eebfb
[ 7.272029] Backport generated by backports.git v6.1.97-1-0-g2431d56e
[ 7.501154] PPP generic driver version 2.4.2
[ 7.508285] NET: Registered PF_PPPOX protocol family
[ 7.667871] ieee80211 phy0: Atheros AR9300 Rev:3 mem=0x(ptrval), irq=17
[ 7.802519] ieee80211 phy1: Atheros AR9300 Rev:3 mem=0x(ptrval), irq=18
[ 7.815725] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 8.067109] mtdblock: MTD device 'colubris-bid' is NAND, please consider using UBI block devices instead.
[ 8.121283] urngd: v1.0.2 started.
[ 8.317701] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.770427] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.793176] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.278601] random: crng init done
[ 9.282018] random: 28 urandom warning(s) missed due to ratelimiting
[ 9.299752] mtdblock: MTD device 'colubris-bid' is NAND, please consider using UBI block devices instead.
[ 17.125048] device phy0-ap0 entered promiscuous mode
[ 17.141814] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 17.666504] fsl-gianfar soc@ffe00000:ethernet@b0000 eth0: Link is Up - 1Gbps/Full - flow control off
BusyBox v1.36.1 (2024-07-15 22:14:18 UTC) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt 23.05.4, r24012-d8dd03c46f
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------