So i started this project as my current location has no proper method of internet, however i can get decent 5g. on my GLiNET Slate AX3000 which uses RM520N-GL i get 700/100 (official firmware).
i however sold that device to a friend. i then purchased a ZBT Z8102AX (official OpenWRT from here) also with a RM520N-GL and things were great. however, my parents provide increased prices so much that we have to rejoin them as new customers to get 50% discount. very silly so in the mean time they are using it. i have another ZBT Z8102AX(Official OpenWRT from here) and purchased a FM190W-GL as it uses a newer Snapdragon modem. unfortunately i was unable to ever get the modem to work and have since been plugging my device and tethering instead. i kept getting a sim not found message or SIM_ILLEGAL_STATE.
the FM190W-GL seller insisted it was due to it being unsupported by ZBT.
low behold a new purchase, Banana PI R4.
i have since built on firmware selector an image with QMI and all its modules. still i get the illegal state message on the banana pi r4 as before.
anyone got any tips to get it working?
read OpenWrt with FM190W-GL module - cannot detect SIM
and FM190W-GL OpenWrt Built-in (Request Guidance) ?
read both of them. followed the instructions. ive been trying for a few months. been reading the forum a lot. i cant get the sim read properly by the fibocom module it seems and i dont know why as the sim works in other devices
Did you read the modem documentation? As I mentioned on another thread, the SIM is read by the modem itself, that has nothing to do with OpenWrt (most of the time).
Show the output of the following commands:
AT+MSMPD?
AT+GTDUALSIM?
AT+GTUSBMODE?
Thanks Andrew, i did read your link and used it when i was on the ZBT Z8102AX. i didn't have much luck. however, i'm trying to do it now in the banana pi and i can't even see my modem as a usb device. i can see cdc-wdm0 when i dmesg. i am booting of the SD Card currently in the banana pi
root@OpenWrt:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd090]
[ 0.000000] Linux version 6.6.63 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r28161-ea17e958b9) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Tue Dec 3 11:41:08 2024
[ 0.000000] Machine model: Bananapi BPI-R4
[ 0.000000] OF: reserved mem: 0x0000000042ff0000..0x0000000042ffffff (64 KiB) map non-reusable ramoops@42ff0000
[ 0.000000] OF: reserved mem: 0x0000000043000000..0x000000004304ffff (320 KiB) nomap non-reusable secmon@43000000
[ 0.000000] OF: reserved mem: 0x0000000047cc0000..0x0000000047dbffff (1024 KiB) nomap non-reusable wmcpu-reserved@47cc0000
[ 0.000000] OF: reserved mem: 0x000000004f600000..0x000000004f63ffff (256 KiB) nomap non-reusable wo-emi@4f600000
[ 0.000000] OF: reserved mem: 0x000000004f640000..0x000000004f67ffff (256 KiB) nomap non-reusable wo-emi@4f640000
[ 0.000000] OF: reserved mem: 0x000000004f680000..0x000000004f6bffff (256 KiB) nomap non-reusable wo-emi@4f680000
[ 0.000000] OF: reserved mem: 0x000000004f700000..0x000000004fefffff (8192 KiB) nomap non-reusable wo-data@4f700000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x00000000ffffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal [mem 0x0000000100000000-0x000000013fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff]
[ 0.000000] node 0: [mem 0x0000000043000000-0x000000004304ffff]
[ 0.000000] node 0: [mem 0x0000000043050000-0x0000000047cbffff]
[ 0.000000] node 0: [mem 0x0000000047cc0000-0x0000000047dbffff]
[ 0.000000] node 0: [mem 0x0000000047dc0000-0x000000004f5fffff]
[ 0.000000] node 0: [mem 0x000000004f600000-0x000000004f6bffff]
[ 0.000000] node 0: [mem 0x000000004f6c0000-0x000000004f6fffff]
[ 0.000000] node 0: [mem 0x000000004f700000-0x000000004fefffff]
[ 0.000000] node 0: [mem 0x000000004ff00000-0x000000013fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000013fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.4
[ 0.000000] percpu: Embedded 18 pages/cpu s35560 r8192 d29976 u73728
[ 0.000000] pcpu-alloc: s35560 r8192 d29976 u73728 alloc=18*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: detected: Spectre-BHB
[ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Kernel command line: console=ttyS0,115200n1 pci=pcie_bus_perf root=/dev/fit0 rootwait
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1032192
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: area num 4.
[ 0.000000] software IO TLB: mapped [mem 0x00000000fa7dd000-0x00000000fe7dd000] (64MB)
[ 0.000000] Memory: 4024564K/4194304K available (9024K kernel code, 996K rwdata, 1664K rodata, 448K init, 307K bss, 169740K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 416 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] Root IRQ handler: 0xffffffc080010080
[ 0.000000] GICv3: GICv3 features: 16 PPIs
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
[ 0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns
[ 0.000064] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000)
[ 0.000071] pid_max: default: 32768 minimum: 301
[ 0.002146] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.002159] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.003645] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.003931] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[ 0.004009] rcu: Hierarchical SRCU implementation.
[ 0.004011] rcu: Max phase no-delay instances is 1000.
[ 0.004301] smp: Bringing up secondary CPUs ...
[ 0.004518] Detected VIPT I-cache on CPU1
[ 0.004554] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000
[ 0.004575] CPU1: Booted secondary processor 0x0000000001 [0x411fd090]
[ 0.004822] Detected VIPT I-cache on CPU2
[ 0.004842] GICv3: CPU2: found redistributor 2 region 0:0x000000000c0c0000
[ 0.004852] CPU2: Booted secondary processor 0x0000000002 [0x411fd090]
[ 0.005083] Detected VIPT I-cache on CPU3
[ 0.005103] GICv3: CPU3: found redistributor 3 region 0:0x000000000c0e0000
[ 0.005112] CPU3: Booted secondary processor 0x0000000003 [0x411fd090]
[ 0.005142] smp: Brought up 1 node, 4 CPUs
[ 0.005146] SMP: Total of 4 processors activated.
[ 0.005149] CPU features: detected: 32-bit EL0 Support
[ 0.005151] CPU features: detected: CRC32 instructions
[ 0.005167] spectre-bhb mitigation disabled by compile time option
[ 0.005180] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.005184] CPU: All CPU(s) started at EL2
[ 0.005185] alternatives: applying system-wide alternatives
[ 0.008692] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.008703] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.009647] pinctrl core: initialized pinctrl subsystem
[ 0.010502] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.010793] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
[ 0.010895] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.010988] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.011269] thermal_sys: Registered thermal governor 'fair_share'
[ 0.011271] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.011273] thermal_sys: Registered thermal governor 'step_wise'
[ 0.011275] thermal_sys: Registered thermal governor 'user_space'
[ 0.011322] ASID allocator initialised with 65536 entries
[ 0.011982] pstore: Using crash dump compression: deflate
[ 0.011987] printk: console [ramoops-1] enabled
[ 0.012222] pstore: Registered ramoops as persistent store backend
[ 0.012226] ramoops: using 0x10000@0x42ff0000, ecc: 0
[ 0.019625] Modules: 29616 pages in range for non-PLT usage
[ 0.019633] Modules: 521136 pages in range for PLT usage
[ 0.020434] cryptd: max_cpu_qlen set to 1000
[ 0.021242] SCSI subsystem initialized
[ 0.021310] libata version 3.00 loaded.
[ 0.022187] clocksource: Switched to clocksource arch_sys_counter
[ 0.023835] NET: Registered PF_INET protocol family
[ 0.023971] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.026546] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[ 0.026569] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.026578] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.026678] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear)
[ 0.027089] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.027414] MPTCP token hash table entries: 4096 (order: 4, 98304 bytes, linear)
[ 0.027542] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.027591] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.027901] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.027934] PCI: CLS 0 bytes, default 64
[ 0.028877] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[ 0.032568] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.032575] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.053258] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.054225] mtk-xsphy soc:xphy@11e10000: failed to get ref_clk(id-1)
[ 0.054828] mtk-pcie-gen3 11280000.pcie: host bridge /soc/pcie@11280000 ranges:
[ 0.054847] mtk-pcie-gen3 11280000.pcie: Parsing ranges property...
[ 0.054859] mtk-pcie-gen3 11280000.pcie: IO 0x0020000000..0x00201fffff -> 0x0020000000
[ 0.054872] mtk-pcie-gen3 11280000.pcie: MEM 0x0020200000..0x0027ffffff -> 0x0020200000
[ 0.054961] mtk-pcie-gen3 11290000.pcie: host bridge /soc/pcie@11290000 ranges:
[ 0.054971] mtk-pcie-gen3 11290000.pcie: Parsing ranges property...
[ 0.054981] mtk-pcie-gen3 11290000.pcie: IO 0x0028000000..0x00281fffff -> 0x0028000000
[ 0.054991] mtk-pcie-gen3 11290000.pcie: MEM 0x0028200000..0x002fffffff -> 0x0028200000
[ 0.055008] /soc/pcie@11290000: Failed to get clk index: 0 ret: -517
[ 0.055017] mtk-pcie-gen3 11290000.pcie: failed to get clocks
[ 0.055078] mtk-pcie-gen3 11300000.pcie: host bridge /soc/pcie@11300000 ranges:
[ 0.055089] mtk-pcie-gen3 11300000.pcie: Parsing ranges property...
[ 0.055098] mtk-pcie-gen3 11300000.pcie: IO 0x0030000000..0x00301fffff -> 0x0030000000
[ 0.055107] mtk-pcie-gen3 11300000.pcie: MEM 0x0030200000..0x0037ffffff -> 0x0030200000
[ 0.055122] /soc/pcie@11300000: Failed to get clk index: 0 ret: -517
[ 0.055130] mtk-pcie-gen3 11300000.pcie: failed to get clocks
[ 0.055210] mtk-pcie-gen3 11310000.pcie: host bridge /soc/pcie@11310000 ranges:
[ 0.055220] mtk-pcie-gen3 11310000.pcie: Parsing ranges property...
[ 0.055229] mtk-pcie-gen3 11310000.pcie: IO 0x0038000000..0x00381fffff -> 0x0038000000
[ 0.055238] mtk-pcie-gen3 11310000.pcie: MEM 0x0038200000..0x003fffffff -> 0x0038200000
[ 0.055254] /soc/pcie@11310000: Failed to get clk index: 0 ret: -517
[ 0.055262] mtk-pcie-gen3 11310000.pcie: failed to get clocks
[ 0.059756] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.061897] printk: console [ttyS0] disabled
[ 0.082191] 11000000.serial: ttyS0 at MMIO 0x11000000 (irq = 99, base_baud = 2500000) is a ST16650V2
[ 0.082226] printk: console [ttyS0] enabled
[ 1.096003] 11000100.serial: ttyS1 at MMIO 0x11000100 (irq = 100, base_baud = 2500000) is a ST16650V2
[ 1.125861] 11000200.serial: ttyS2 at MMIO 0x11000200 (irq = 101, base_baud = 2500000) is a ST16650V2
[ 1.137791] loop: module loaded
[ 1.142253] spi-nand spi0.0: Winbond SPI NAND was found.
[ 1.147572] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[ 1.155834] 2 fixed-partitions partitions found on MTD device spi0.0
[ 1.162200] OF: Bad cell count for /soc/spi@11007000/spi_nand@0/partitions
[ 1.169072] OF: Bad cell count for /soc/spi@11007000/spi_nand@0/partitions
[ 1.176159] Creating 2 MTD partitions on "spi0.0":
[ 1.180944] 0x000000000000-0x000000200000 : "bl2"
[ 1.187130] 0x000000200000-0x000008000000 : "ubi"
[ 1.267732] ubi0: default fastmap pool size: 50
[ 1.272268] ubi0: default fastmap WL pool size: 25
[ 1.277048] ubi0: attaching mtd1
[ 2.098317] ubi0: scanning is finished
[ 2.111704] ubi0: attached mtd1 (name "ubi", size 126 MiB)
[ 2.117193] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 2.124060] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 2.130835] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 2.137784] ubi0: good PEBs: 1008, bad PEBs: 0, corrupted PEBs: 0
[ 2.143867] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 2.151076] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1697192243
[ 2.160195] ubi0: available PEBs: 105, total reserved PEBs: 903, PEBs reserved for bad PEB handling: 20
[ 2.169578] ubi0: background thread "ubi_bgt0d" started, PID 306
[ 2.170323] block ubiblock0_1: created from ubi0:1(rootfs)
[ 2.181056] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 2.313693] i2c_dev: i2c /dev entries driver
[ 2.321120] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[ 2.329229] mtk-cpufreq mtk-cpufreq: failed to initialize dvfs info for cpu0
[ 2.336781] mtk-msdc 11230000.mmc: Got CD GPIO
[ 2.336953] NET: Registered PF_INET6 protocol family
[ 2.346608] Segment Routing with IPv6
[ 2.350274] In-situ OAM (IOAM) with IPv6
[ 2.354226] NET: Registered PF_PACKET protocol family
[ 2.359278] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.372311] 8021q: 802.1Q VLAN Support v1.8
[ 2.389514] phy phy-soc:xphy@11e10000.3: type_sw - reg 0x218, index 0
[ 2.396768] mtk-pcie-gen3 11280000.pcie: host bridge /soc/pcie@11280000 ranges:
[ 2.404115] mtk-pcie-gen3 11280000.pcie: Parsing ranges property...
[ 2.410391] mtk-pcie-gen3 11280000.pcie: IO 0x0020000000..0x00201fffff -> 0x0020000000
[ 2.418840] mtk-pcie-gen3 11280000.pcie: MEM 0x0020200000..0x0027ffffff -> 0x0020200000
[ 2.432939] mmc0: host does not support reading read-only switch, assuming write-enable
[ 2.444093] mmc0: new high speed SDXC card at address aaaa
[ 2.450156] mmcblk0: mmc0:aaaa SN128 119 GiB
[ 2.457453] Alternate GPT is invalid, using primary GPT.
[ 2.462782] mmcblk0: p1 p2 p3 p4 p5 p6 p7
[ 2.762204] mtk-pcie-gen3 11280000.pcie: PCIe link down, current LTSSM state: detect.quiet (0x1)
[ 2.771011] mtk-pcie-gen3: probe of 11280000.pcie failed with error -110
[ 2.778085] mtk-pcie-gen3 11290000.pcie: host bridge /soc/pcie@11290000 ranges:
[ 2.785406] mtk-pcie-gen3 11290000.pcie: Parsing ranges property...
[ 2.791671] mtk-pcie-gen3 11290000.pcie: IO 0x0028000000..0x00281fffff -> 0x0028000000
[ 2.800107] mtk-pcie-gen3 11290000.pcie: MEM 0x0028200000..0x002fffffff -> 0x0028200000
[ 3.142190] mtk-pcie-gen3 11290000.pcie: PCIe link down, current LTSSM state: detect.quiet (0x1)
[ 3.150971] mtk-pcie-gen3: probe of 11290000.pcie failed with error -110
[ 3.157846] mtk-pcie-gen3 11300000.pcie: host bridge /soc/pcie@11300000 ranges:
[ 3.165157] mtk-pcie-gen3 11300000.pcie: Parsing ranges property...
[ 3.171417] mtk-pcie-gen3 11300000.pcie: IO 0x0030000000..0x00301fffff -> 0x0030000000
[ 3.179849] mtk-pcie-gen3 11300000.pcie: MEM 0x0030200000..0x0037ffffff -> 0x0030200000
[ 3.522190] mtk-pcie-gen3 11300000.pcie: PCIe link down, current LTSSM state: detect.quiet (0x1)
[ 3.530969] mtk-pcie-gen3: probe of 11300000.pcie failed with error -110
[ 3.537830] mtk-pcie-gen3 11310000.pcie: host bridge /soc/pcie@11310000 ranges:
[ 3.545141] mtk-pcie-gen3 11310000.pcie: Parsing ranges property...
[ 3.551400] mtk-pcie-gen3 11310000.pcie: IO 0x0038000000..0x00381fffff -> 0x0038000000
[ 3.559831] mtk-pcie-gen3 11310000.pcie: MEM 0x0038200000..0x003fffffff -> 0x0038200000
[ 3.902200] mtk-pcie-gen3 11310000.pcie: PCIe link down, current LTSSM state: detect.quiet (0x1)
[ 3.910979] mtk-pcie-gen3: probe of 11310000.pcie failed with error -110
[ 3.918440] FIT: Detected U-Boot 2024.10-OpenWrt-r28161-ea17e958b9
[ 3.924619] FIT: Selected configuration: "config-mt7988a-bananapi-bpi-r4" (OpenWrt bananapi_bpi-r4)
[ 3.933662] FIT: kernel sub-image 0x00001000..0x0055d00f "kernel-1" (ARM64 OpenWrt Linux-6.6.63)
[ 3.943398] FIT: flat_dt sub-image 0x0055e000..0x00569a15 "fdt-1" (ARM64 OpenWrt bananapi_bpi-r4 device tree blob)
[ 3.954608] FIT: flat_dt sub-image 0x0056a000..0x0056a609 "fdt-mt7988a-bananapi-bpi-r4-emmc" (ARM64 OpenWrt bananapi_bpi-r4 device tree overlay mt7988a-bananapi-bpi-r4-emmc)
[ 3.970937] FIT: flat_dt sub-image 0x0056b000..0x0056b11c "fdt-mt7988a-bananapi-bpi-r4-rtc" (ARM64 OpenWrt bananapi_bpi-r4 device tree overlay mt7988a-bananapi-bpi-r4-rtc)
[ 3.987091] FIT: flat_dt sub-image 0x0056c000..0x0056c5c1 "fdt-mt7988a-bananapi-bpi-r4-sd" (ARM64 OpenWrt bananapi_bpi-r4 device tree overlay mt7988a-bananapi-bpi-r4-sd)
[ 4.003073] FIT: flat_dt sub-image 0x0056d000..0x0056d8f0 "fdt-mt7988a-bananapi-bpi-r4-wifi-mt7996a" (ARM64 OpenWrt bananapi_bpi-r4 device tree overlay mt7988a-bananapi-bpi-r4-wifi-mt7996a)
[ 4.020787] FIT: filesystem sub-image 0x0056e000..0x01036fff "rootfs-1" (ARM64 OpenWrt bananapi_bpi-r4 rootfs)
[ 4.031650] block mmcblk0p7: mapped 1 uImage.FIT filesystem sub-image as /dev/fit0
[ 4.039398] block mmcblk0p7: mapped remaining space as /dev/fitrw
[ 4.173647] mtk_soc_eth 15100000.ethernet: generated random MAC address 65:74:68:25:64:00
[ 4.186062] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc082700000, irq 106
[ 4.195733] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc082700000, irq 106
[ 4.205393] mtk_soc_eth 15100000.ethernet eth2: mediatek frame engine at 0xffffffc082700000, irq 106
[ 4.296025] mt7530-mmio 15020000.switch: configuring for fixed/internal link mode
[ 4.303539] mt7530-mmio 15020000.switch: Link is Up - 10Gbps/Full - flow control rx/tx
[ 4.330118] mt7530-mmio 15020000.switch wan (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7988 PHY] (irq=115)
[ 4.368134] mt7530-mmio 15020000.switch lan1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7988 PHY] (irq=116)
[ 4.406637] mt7530-mmio 15020000.switch lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7988 PHY] (irq=117)
[ 4.444937] mt7530-mmio 15020000.switch lan3 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7988 PHY] (irq=118)
[ 4.455927] mtk_soc_eth 15100000.ethernet eth0: entered promiscuous mode
[ 4.462641] DSA: tree 0 setup
[ 4.465872] clk: Disabling unused clocks
[ 4.475824] VFS: Mounted root (squashfs filesystem) readonly on device 259:0.
[ 4.483064] Freeing unused kernel memory: 448K
[ 4.487538] Run /sbin/init as init process
[ 4.491622] with arguments:
[ 4.494585] /sbin/init
[ 4.497281] with environment:
[ 4.500410] HOME=/
[ 4.502796] TERM=linux
[ 4.638166] init: Console is alive
[ 4.641644] init: - watchdog -
[ 4.924872] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.949069] usbcore: registered new interface driver usbfs
[ 4.954614] usbcore: registered new interface driver hub
[ 4.959938] usbcore: registered new device driver usb
[ 4.965460] gpio_button_hotplug: loading out-of-tree module taints kernel.
[ 4.975235] xhci-mtk 11200000.usb: supply vbus not found, using dummy regulator
[ 4.982648] xhci-mtk 11200000.usb: supply vusb33 not found, using dummy regulator
[ 4.990549] xhci-mtk 11200000.usb: xHCI Host Controller
[ 4.995802] xhci-mtk 11200000.usb: new USB bus registered, assigned bus number 1
[ 5.006240] xhci-mtk 11200000.usb: hcc params 0x01403f99 hci version 0x110 quirks 0x0000000000200010
[ 5.015399] xhci-mtk 11200000.usb: irq 119, io mem 0x11200000
[ 5.021204] xhci-mtk 11200000.usb: xHCI Host Controller
[ 5.026447] xhci-mtk 11200000.usb: new USB bus registered, assigned bus number 2
[ 5.033840] xhci-mtk 11200000.usb: Host supports USB 3.2 Enhanced SuperSpeed
[ 5.041193] hub 1-0:1.0: USB hub found
[ 5.044996] hub 1-0:1.0: 1 port detected
[ 5.049104] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 5.057402] hub 2-0:1.0: USB hub found
[ 5.061156] hub 2-0:1.0: 1 port detected
[ 5.067411] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.077705] init: - preinit -
[ 5.303867] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/internal link mode
[ 5.312013] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 10Gbps/Full - flow control rx/tx
[ 5.331847] mt7530-mmio 15020000.switch lan1: configuring for phy/internal link mode
[ 5.512194] usb 1-1: new high-speed USB device number 2 using xhci-mtk
[ 5.704831] hub 1-1:1.0: USB hub found
[ 5.708748] hub 1-1:1.0: 5 ports detected
[ 5.852245] usb 2-1: new SuperSpeed USB device number 2 using xhci-mtk
[ 5.884753] hub 2-1:1.0: USB hub found
[ 5.888677] hub 2-1:1.0: 4 ports detected
[ 6.402184] usb 1-1.5: new high-speed USB device number 3 using xhci-mtk
[ 6.792187] random: crng init done
[ 9.819087] F2FS-fs (fitrw): Disable nat_bits due to incorrect cp_ver (3506757205867614403, 828914692461678773)
[ 9.832783] F2FS-fs (fitrw): Mounted with checkpoint version = 6147d0c3
[ 9.841032] mount_root: switching to f2fs overlay
[ 9.848793] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[ 9.860561] urandom-seed: Seeding with /etc/urandom.seed
[ 9.899876] procd: - early -
[ 9.902827] procd: - watchdog -
[ 10.436693] procd: - watchdog -
[ 10.440129] procd: - ubus -
[ 10.595241] procd: - init -
[ 10.817713] kmodloader: loading kernel modules from /etc/modules.d/*
[ 10.840717] pca954x 1-0070: supply vdd not found, using dummy regulator
[ 10.847970] i2c i2c-1: Added multiplexed i2c bus 2
[ 10.852896] i2c i2c-1: Added multiplexed i2c bus 3
[ 10.857766] i2c i2c-1: Added multiplexed i2c bus 4
[ 10.862638] i2c i2c-1: Added multiplexed i2c bus 5
[ 10.867422] pca954x 1-0070: registered 4 multiplexed busses for I2C switch pca9545
[ 10.878537] crypto-safexcel 15600000.crypto: can't request region for resource [mem 0x15600000-0x1577ffff]
[ 10.882882] urngd: v1.0.2 started.
[ 10.888197] crypto-safexcel 15600000.crypto: failed to get resource
[ 10.897835] crypto-safexcel: probe of 15600000.crypto failed with error -16
[ 10.908590] at24 2-0050: supply vcc not found, using dummy regulator
[ 10.944038] at24 2-0057: supply vcc not found, using dummy regulator
[ 10.950980] at24 2-0057: 256 byte 24c02 EEPROM, writable, 1 bytes/write
[ 10.958227] usbcore: registered new interface driver cdc_wdm
[ 10.964292] Loading modules backported from Linux version v6.11.2-0-g7aa21fec187b
[ 10.971764] Backport generated by backports.git v6.1.110-1-32-gc61f71fe0942
[ 10.981621] sfp sfp1: Host maximum power 3.0W
[ 10.986512] sfp sfp2: Host maximum power 3.0W
[ 10.993102] usbcore: registered new interface driver usbserial_generic
[ 10.999654] usbserial: USB Serial support registered for generic
[ 11.030739] PPP generic driver version 2.4.2
[ 11.035459] NET: Registered PF_PPPOX protocol family
[ 11.041049] usbcore: registered new interface driver qmi_wwan
[ 11.048777] usbcore: registered new interface driver qcserial
[ 11.054566] usbserial: USB Serial support registered for Qualcomm USB modem
[ 11.061617] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 12.760315] mtk_soc_eth 15100000.ethernet eth0: Link is Down
[ 12.785600] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/internal link mode
[ 12.793775] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 10Gbps/Full - flow control rx/tx
[ 12.796669] mt7530-mmio 15020000.switch lan1: configuring for phy/internal link mode
[ 12.810849] br-lan: port 1(lan1) entered blocking state
[ 12.816161] br-lan: port 1(lan1) entered disabled state
[ 12.821419] mt7530-mmio 15020000.switch lan1: entered allmulticast mode
[ 12.828057] mtk_soc_eth 15100000.ethernet eth0: entered allmulticast mode
[ 12.835048] mt7530-mmio 15020000.switch lan1: entered promiscuous mode
[ 12.846527] mt7530-mmio 15020000.switch lan2: configuring for phy/internal link mode
[ 12.855221] br-lan: port 2(lan2) entered blocking state
[ 12.860479] br-lan: port 2(lan2) entered disabled state
[ 12.865752] mt7530-mmio 15020000.switch lan2: entered allmulticast mode
[ 12.872565] mt7530-mmio 15020000.switch lan2: entered promiscuous mode
[ 12.881495] mt7530-mmio 15020000.switch lan3: configuring for phy/internal link mode
[ 12.890108] br-lan: port 3(lan3) entered blocking state
[ 12.895372] br-lan: port 3(lan3) entered disabled state
[ 12.900619] mt7530-mmio 15020000.switch lan3: entered allmulticast mode
[ 12.907480] mt7530-mmio 15020000.switch lan3: entered promiscuous mode
[ 12.915770] mtk_soc_eth 15100000.ethernet eth1: configuring for inband/10gbase-r link mode
[ 12.947991] br-lan: port 4(eth1) entered blocking state
[ 12.953258] br-lan: port 4(eth1) entered disabled state
[ 12.958511] mtk_soc_eth 15100000.ethernet eth1: entered allmulticast mode
[ 12.965583] mtk_soc_eth 15100000.ethernet eth1: entered promiscuous mode
[ 42.272336] usb 2-1.1: new SuperSpeed USB device number 3 using xhci-mtk
[ 42.303659] usb 2-1.1: LPM exit latency is zeroed, disabling LPM.
[ 42.321994] qmi_wwan 2-1.1:1.4: cdc-wdm0: USB WDM device
[ 42.327969] qmi_wwan 2-1.1:1.4 wwan0: register 'qmi_wwan' at usb-11200000.usb-1.1, WWAN/QMI device, xx:xx:xx:xx:xx:xx
[ 1984.907565] mt7530-mmio 15020000.switch lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 1984.908156] br-lan: port 1(lan1) entered blocking state
[ 1984.921054] br-lan: port 1(lan1) entered forwarding state
so i can't picocom the right device and send the AT commands currently
That's weird because I can:
Please show the output of cat /sys/kernel/debug/usb/devices
i see that but not as a USBtty device like i used to in the other device and when i type picocom /dev/cdc-wdm0 i get a fatal error
here is the output
root@OpenWrt:~# cat /sys/kernel/debug/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 6.06
S: Manufacturer=Linux 6.6.63 xhci-hcd
S: Product=xHCI Host Controller
S: SerialNumber=11200000.usb
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 5
D: Ver= 2.10 Cls=09(hub ) Sub=00 Prot=02 MxPS=64 #Cfgs= 1
P: Vendor=2109 ProdID=2822 Rev= 0.30
S: Manufacturer=VIA Labs, Inc.
S: Product=USB2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=01 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
I:* If#= 0 Alt= 1 #EPs= 1 Cls=09(hub ) Sub=00 Prot=02 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
T: Bus=01 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=11(blbrd) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2109 ProdID=8822 Rev= 0.01
S: Manufacturer=VIA Labs, Inc.
S: Product=USB Billboard Device
S: SerialNumber=0000000000000001
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 0 Cls=11(blbrd) Sub=00 Prot=00 Driver=(none)
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=10000 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 3.10 Cls=09(hub ) Sub=00 Prot=03 MxPS= 9 #Cfgs= 1
P: Vendor=1d6b ProdID=0003 Rev= 6.06
S: Manufacturer=Linux 6.6.63 xhci-hcd
S: Product=xHCI Host Controller
S: SerialNumber=11200000.usb
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 4
D: Ver= 3.10 Cls=09(hub ) Sub=00 Prot=03 MxPS= 9 #Cfgs= 1
P: Vendor=2109 ProdID=0822 Rev= 0.30
S: Manufacturer=VIA Labs, Inc.
S: Product=USB3.1 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=13(Int.) MxPS= 2 Ivl=16ms
T: Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=2cb7 ProdID=0104 Rev= 5.15
S: Manufacturer=QCOM
S: Product=SDXPINN-IDP _SN:D33XXXXX
S: SerialNumber=d33xxxxx
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=896mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none)
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=(none)
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=87(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
Install kmod-usb-serial-option if not installed and re-read USB information again.
can that be installed at the same time as kmod-usb-serial-qualcomm?
part of the QMI tutorial it says to use kmod-usb-serial-option or kmod-usb-serial-qualcomm
i opted for qualcomm as the chip is qualcomm based. can i have both installed or do they have a comflict?
Yes, but kmod-usb-serial-qualcomm is not needed.
root@OpenWrt:~# cat /sys/kernel/debug/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 6.06
S: Manufacturer=Linux 6.6.63 xhci-hcd
S: Product=xHCI Host Controller
S: SerialNumber=11200000.usb
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 5
D: Ver= 2.10 Cls=09(hub ) Sub=00 Prot=02 MxPS=64 #Cfgs= 1
P: Vendor=2109 ProdID=2822 Rev= 0.30
S: Manufacturer=VIA Labs, Inc.
S: Product=USB2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=01 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
I:* If#= 0 Alt= 1 #EPs= 1 Cls=09(hub ) Sub=00 Prot=02 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
T: Bus=01 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=11(blbrd) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2109 ProdID=8822 Rev= 0.01
S: Manufacturer=VIA Labs, Inc.
S: Product=USB Billboard Device
S: SerialNumber=0000000000000001
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 0 Cls=11(blbrd) Sub=00 Prot=00 Driver=(none)
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=10000 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 3.10 Cls=09(hub ) Sub=00 Prot=03 MxPS= 9 #Cfgs= 1
P: Vendor=1d6b ProdID=0003 Rev= 6.06
S: Manufacturer=Linux 6.6.63 xhci-hcd
S: Product=xHCI Host Controller
S: SerialNumber=11200000.usb
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 4
D: Ver= 3.10 Cls=09(hub ) Sub=00 Prot=03 MxPS= 9 #Cfgs= 1
P: Vendor=2109 ProdID=0822 Rev= 0.30
S: Manufacturer=VIA Labs, Inc.
S: Product=USB3.1 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=13(Int.) MxPS= 2 Ivl=16ms
T: Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=2cb7 ProdID=0104 Rev= 5.15
S: Manufacturer=QCOM
S: Product=SDXPINN-IDP _SN:D33XXXXX
S: SerialNumber=d33xxxxx
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=896mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=87(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
and now i do get an dmesg
root@OpenWrt:~# dmesg | grep -A 1 -B 12 ttyUSB
[ 10.968597] usbserial: USB Serial support registered for generic
[ 10.975765] usbcore: registered new interface driver cdc_ether
[ 10.982394] usbcore: registered new interface driver cdc_ncm
[ 11.015639] PPP generic driver version 2.4.2
[ 11.020528] NET: Registered PF_PPPOX protocol family
[ 11.031502] qmi_wwan 2-1.1:1.4: cdc-wdm0: USB WDM device
[ 11.040811] qmi_wwan 2-1.1:1.4 wwan0: register 'qmi_wwan' at usb-11200000.usb-1.1, WWAN/QMI device, be:a3:ae:e6:ef:7a
[ 11.051602] usbcore: registered new interface driver qmi_wwan
[ 11.058951] usbcore: registered new interface driver cdc_mbim
[ 11.066155] usbcore: registered new interface driver option
[ 11.071790] usbserial: USB Serial support registered for GSM modem (1-port)
[ 11.078982] option 2-1.1:1.0: GSM modem (1-port) converter detected
[ 11.085456] usb 2-1.1: GSM modem (1-port) converter now attached to ttyUSB0
[ 11.092637] option 2-1.1:1.1: GSM modem (1-port) converter detected
[ 11.099083] usb 2-1.1: GSM modem (1-port) converter now attached to ttyUSB1
[ 11.106250] option 2-1.1:1.2: GSM modem (1-port) converter detected
[ 11.112723] usb 2-1.1: GSM modem (1-port) converter now attached to ttyUSB2
[ 11.119867] option 2-1.1:1.3: GSM modem (1-port) converter detected
[ 11.126335] usb 2-1.1: GSM modem (1-port) converter now attached to ttyUSB3
[ 11.134581] kmodloader: done loading kernel modules from /etc/modules.d/*
so i will try find a port that does accept my picocom AT commands and report back
Hi Andrew,
picocom is now hanging on all /dev/ttyUSB0,/dev/ttyUSB1,/dev/ttyUSB2,/dev/ttyUSB3
1 of them should work so a bit confused
Try to reboot/reset and then try the 3rd interface only, /dev/ttyUSB2
`type or paste code here`
seems to have worked. to get the data
AT+MSMPD?
+MSMPD: 0
OK
AT+GTDUALSIM?
+GTDUALSIM: 1,"SUB2","No Service"
OK
AT+GTUSBMODE?
+GTUSBMODE: 32
OK
Set AT+GTDUALSIM=0
I would also change the mode to MBIM with AT+GTUSBMODE=30 and then follow https://openwrt.org/docs/guide-user/network/wan/wwan/ltedongle
I was told to change the mode to 32 but i have changed it back to 30
17 DIAG + MODEM + AT + PIPE + RMNET + ADB
18 DIAG + MODEM + AT + PIPE + ECM + ADB
20 MODEM
21 MODEM + AT
24 RNDIS + MODEM + DIAG + ADB
29 MBIM+AT+ DIAG
30 MBIM + MODEM + DIAG + AT
31 DIAG + MODEM + RMNET + DPL + QDSS + ADB
32 DIAG + MODEM + AT + PIPE + RMNET
33 DIAG + MODEM + AT + PIPE + EC
will this utilise the modem in full speed, i.e. not in usb mode but in pcie mode?
This only changes configuration or composition while the modem is in USB mode.
is there any other mode it can be in apart from USB mode for max speeds? i'm trying to run when i'm not even crawling
The illegal state error has re-appeared and i've made no changes apart from the previous instructions you sent
i appreciate the assistance
Your modem is currently working on USB3. I have not seen any mention of this modem operating via PCI probably besides this one.
Please show the current state of:
AT+GTDUALSIM?
AT+CPIN?
AT+CGDCONT?
haha guess what modem i have? the same one as that guy and he's using the banana pi too.
+GTUSBMODE: 30
OK
+GTDUALSIM: 0,"SUB1","L"
OK
+CPIN: READY
OK
+CGDCONT: 1,"IP","mob.asm.net","10.79.255.38",1,0,0,0,,,,,,,,,"",,,,0
+CGDCONT: 2,"IPV4V6","ims","0.0.0.0,42.4.74.67.2.189.60.247.0.0.0.0.78.249.219.160",0,0,0,0,,,,,,,,,"",,,,0
+CGDCONT: 3,"IPV4V6","sos","0.0.0.0,0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,1,,,,,,,,,"",,,,0
OK
should i blank out the apn and IP?