After change OpenWrt from 18.08 to 21.02 , usb devices don't work !
HiLink Huawei do not charge and don't work, other devices like usb flash dont work.
After back to 18.08 works.
Easy box 802 Astoria ARV752DPW EasyBox 802 R01
data from openwrt 21.02
Model : Arcor 802
fw OpenWrt 21.02.0 r16279-5cc0535800 / LuCI openwrt-21.02 branch git-21.231.26241-422c175
installed the packages required for usb support ?
Danube is seeing barely any usage/ testing, so regressions can happen…
The very least you should confirm as a first step though, is where the breakage happened, with 19.07.x or 21.02.x. Given the very limited developer- and device coverage for non-vr9 lantiq SOCs, you'd probably have to debug further from there, but you'd have to start somewhere to pin point the breakage point.
@slh There is no 19.07 image for this router.
@ frollic I have installed all packges form https://eko.one.pl/?p=openwrt-3ginfo and other.
then you should probably as at eko.one.pl, but what does lsusb and dmesg say when you plug in your Huawei device ?
I think the problem is in power on usb port.
I conected Huawei HiLink modem and it do not loading battery.
USB Flash don't flashing
.
This problem is in Openwrt 21.x.x. , but I don't know how to fix it.
lsusb
-ash: lsusb: not found
root@OpenWrt:~# dmesg
[ 0.000000] Linux version 5.4.143 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16279-5cc0535800)) #0 Tue Aug 31 22:20:08 2021
[ 0.000000] SoC: Danube rev 1.5
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019641 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Arcor 802
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] Normal zone: 144 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240
[ 0.000000] Kernel command line: console=ttyLTQ0,115200
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.000000] Writing ErrCtl register=0005febc
[ 0.000000] Readback ErrCtl register=0005febc
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 56764K/65536K available (5679K kernel code, 214K rwdata, 768K rodata, 1192K init, 203K bss, 8772K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] random: get_random_bytes called from 0x80686a28 with crng_init=0
[ 0.000000] CPU Clock: 333MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[ 0.000018] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[ 0.008009] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[ 0.054262] pid_max: default: 32768 minimum: 301
[ 0.059355] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.066613] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.086950] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.096639] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.103688] pinctrl core: initialized pinctrl subsystem
[ 0.115199] NET: Registered protocol family 16
[ 0.131054] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.138117] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20
[ 0.149603] PCI host bridge /fpi@10000000/pci@e105400 ranges:
[ 0.155313] MEM 0x0000000018000000..0x0000000019ffffff
[ 0.160590] IO 0x000000001ae00000..0x000000001affffff
[ 0.243725] usbcore: registered new interface driver usbfs
[ 0.249380] usbcore: registered new interface driver hub
[ 0.254803] usbcore: registered new device driver usb
[ 0.260598] PCI host bridge to bus 0000:00
[ 0.264653] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[ 0.271575] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff]
[ 0.278518] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.285368] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.295037] pci 0000:00:0e.0: [1814:0601] type 00 class 0x028000
[ 0.301046] pci 0000:00:0e.0: reg 0x10: [mem 0xffff0000-0xffffffff]
[ 0.307463] pci 0000:00:0e.0: PME# supported from D0 D3hot D3cold
[ 0.315937] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.322524] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[ 0.329551] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[ 0.354324] clocksource: Switched to clocksource MIPS
[ 0.361843] thermal_sys: Registered thermal governor 'step_wise'
[ 0.362691] NET: Registered protocol family 2
[ 0.373385] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.382111] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.390492] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.398177] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.405278] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.411964] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.418496] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.426054] NET: Registered protocol family 1
[ 0.430502] PCI: CLS 0 bytes, default 32
[ 0.441691] gptu: totally 6 16-bit timers/counters
[ 0.446660] gptu: misc_register on minor 63
[ 0.450842] gptu: succeeded to request irq 126
[ 0.455344] gptu: succeeded to request irq 127
[ 0.459859] gptu: succeeded to request irq 128
[ 0.464394] gptu: succeeded to request irq 129
[ 0.468889] gptu: succeeded to request irq 130
[ 0.473400] gptu: succeeded to request irq 131
[ 0.484710] lantiq,vmmc 1f107000.vmmc: requested GPIO 465
[ 0.490073] lantiq,vmmc 1f107000.vmmc: reserved 1MB at 0x(ptrval)
[ 0.502116] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[ 0.526713] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.532490] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.581269] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.596138] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[ 0.605111] printk: console [ttyLTQ0] enabled
[ 0.613576] printk: bootconsole [early0] disabled
[ 0.624816] lantiq nor flash device: 00800000 at 10000000
[ 0.629100] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[ 0.638060] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.643072] Amd/Fujitsu Extended Query version 1.1.
[ 0.647936] number of CFI chips: 1
[ 0.651295] 4 fixed-partitions partitions found on MTD device ltq_nor
[ 0.657467] Creating 4 MTD partitions on "ltq_nor":
[ 0.662212] 0x000000000000-0x000000010000 : "uboot"
[ 0.669092] 0x000000010000-0x000000020000 : "u-boot-env"
[ 0.675258] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.696977] 2 uimage-fw partitions found on MTD device firmware
[ 0.701444] 0x000000020000-0x00000023ed9d : "kernel"
[ 0.708469] 0x00000023ed9d-0x0000007f0000 : "rootfs"
[ 0.714020] mtd: device 4 (rootfs) set to be root filesystem
[ 0.718396] 1 squashfs-split partitions found on MTD device rootfs
[ 0.724232] 0x000000610000-0x0000007f0000 : "rootfs_data"
[ 0.731712] 0x0000007f0000-0x000000800000 : "board_config"
[ 0.741887] libphy: Fixed MDIO Bus: probed
[ 0.781452] libphy: ltq_mii: probed
[ 0.813889] Registering RTL8306SDM switch with Chip ID: 0x5988, version: 0x0000
[ 0.819731] Realtek RTL8306S 1e180000.etop-ffffffff:00: attached PHY driver [Realtek RTL8306S] (mii_bus:phy_addr=1e180000.etop-ffffffff:00, irq=POLL)
[ 0.843569] NET: Registered protocol family 10
[ 0.867007] Segment Routing with IPv6
[ 0.869373] NET: Registered protocol family 17
[ 0.873720] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 0.886153] 8021q: 802.1Q VLAN Support v1.8
[ 0.897269] OF: fdt: not creating '/sys/firmware/fdt': CRC check failed
[ 0.914830] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.927959] Freeing unused kernel memory: 1192K
[ 0.931061] This architecture does not have kernel memory protection.
[ 0.937280] Run /sbin/init as init process
[ 1.178381] random: fast init done
[ 2.798588] init: Console is alive
[ 2.801071] init: - watchdog -
[ 5.805594] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.134742] dwc2 1e101000.usb: 1e101000.usb supply vusb_d not found, using dummy regulator
[ 6.141673] dwc2 1e101000.usb: 1e101000.usb supply vusb_a not found, using dummy regulator
[ 6.163178] dwc2 1e101000.usb: dwc2_core_reset: HANG! Soft Reset timeout GRSTCTL GRSTCTL_CSFTRST
[ 6.171092] dwc2: probe of 1e101000.usb failed with error -16
[ 6.178733] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.195273] init: - preinit -
[ 8.747122] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 8.792645] random: procd: uninitialized urandom read (4 bytes read)
[ 13.529243] jffs2: notice: (471) jffs2_build_xattr_subsystem: complete building xattr subsystem, 28 of xdatum (25 unchecked, 3 orphan) and 36 of xref (3 dead, 0 orphan) found.
[ 13.588899] mount_root: loading kmods from internal overlay
[ 14.868721] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 16.042205] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 16.219061] SCSI subsystem initialized
[ 16.277322] ehci-fsl: Freescale EHCI Host controller driver
[ 16.285914] ehci-platform: EHCI generic platform driver
[ 16.579238] usbcore: registered new interface driver usb-storage
[ 16.585708] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 17.371057] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 17.385664] block: extroot: not configured
[ 17.390484] mount_root: switching to jffs2 overlay
[ 17.400772] overlayfs: upper fs does not support tmpfile.
[ 17.417434] urandom-seed: Seeding with /etc/urandom.seed
[ 17.832192] procd: - early -
[ 17.833859] procd: - watchdog -
[ 18.631357] procd: - watchdog -
[ 18.640365] procd: - ubus -
[ 18.926788] random: ubusd: uninitialized urandom read (4 bytes read)
[ 18.951622] random: ubusd: uninitialized urandom read (4 bytes read)
[ 18.967260] random: ubusd: uninitialized urandom read (4 bytes read)
[ 18.999147] procd: - init -
[ 21.590706] kmodloader: loading kernel modules from /etc/modules.d/*
[ 21.614411] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
[ 21.651739] Lantiq TAPI device driver, version 3.13.0.2, (c) 2001-2010 Lantiq Deutschland GmbH
[ 21.683347] NET: Registered protocol family 8
[ 21.686198] NET: Registered protocol family 20
[ 21.712885] PPP generic driver version 2.4.2
[ 21.781233] IFX MEI Version 5.00.00
[ 21.818746] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
[ 21.851410] Loading modules backported from Linux version v5.10.42-0-g65859eca4dff
[ 21.857477] Backport generated by backports.git v5.10.42-1-0-gbee5c545
[ 21.906724] Lantiq MIPS24KEc MPS driver, version 2.2.2.5, (c) 2006-2010 Lantiq Deutschland GmbH
[ 21.913917] request_timer(3, 0x000001AE, 1)...
[ 21.913953] successful!
[ 21.921015] Lantiq VMMC device driver, version 1.9.0.3, (c) 2006-2010 Lantiq Deutschland GmbH
[ 21.996150] NET: Registered protocol family 24
[ 22.034732] xt_time: kernel timezone is -0000
[ 22.582661] rt2800pci 0000:00:0e.0: enabling device (0000 -> 0002)
[ 22.588656] rt2800pci 0000:00:0e.0: loaded eeprom from mtd device "board_config"
[ 22.594583] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2860, rev 0103 detected
[ 22.602177] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0001 detected
[ 22.608946] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 22.698743] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 22.711771] urngd: v1.0.2 started.
[ 23.842933] random: crng init done
[ 23.844855] random: 6 urandom warning(s) missed due to ratelimiting
[ 31.868668] USB_VBUS: disabling
[ 57.892876] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 57.943241] br-lan: port 1(eth0.1) entered blocking state
[ 57.947207] br-lan: port 1(eth0.1) entered disabled state
[ 57.953091] device eth0.1 entered promiscuous mode
[ 57.957070] device eth0 entered promiscuous mode
[ 58.022525] br-lan: port 1(eth0.1) entered blocking state
[ 58.026486] br-lan: port 1(eth0.1) entered forwarding state
[ 58.903192] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
root@OpenWrt:~#
opkg update && opkg install usbutils
root@OpenWrt:~# Package usbutils (013-2) installed in root is up to date.
It works only when power on , when all leds ON for 1 - 2 seconds.
Normaly in other versions Openwrt the second led from left is red and then power on usb port is active.
others installed
root@OpenWrt:~# opkg list-installed | grep usb
kmod-usb-core - 5.4.143-1
kmod-usb-dwc2 - 5.4.143-1
kmod-usb-ehci - 5.4.143-1
kmod-usb-ledtrig-usbport - 5.4.143-1
kmod-usb-ohci - 5.4.143-1
kmod-usb-ohci-pci - 5.4.143-1
kmod-usb-storage - 5.4.143-1
kmod-usb-storage-uas - 5.4.143-1
kmod-usb-uhci - 5.4.143-1
kmod-usb2 - 5.4.143-1
kmod-usb2-pci - 5.4.143-1
kmod-usb3 - 5.4.143-1
libusb-1.0-0 - 1.0.24-4
usbids - 0.350-1
usbutils - 013-2
For my there is a problem with software openwrt, and don't turn usb port ON.