Devolo Wifi Pro 1200e - openwrt-23.05.3 - Often Wifi Clients Disconnects or wifi interface outages

Tested with multiple OpenWrt 23 Versions and my devices do disconnect often from Wifi AP. It is just configured to be Wifi AP. DHCP, DNS, WAN Modem is handled by other devices. Android Wifi status is often: Access point temporarily fully occupied. This is the first time I ask the community for help. I was using the search first, but no one else with my device type posts here a simmilar issue. I will try to find our more esspacially about the errors in the logs. From the device i got the following logs:

kernel.log

[    0.000000] Linux version 5.15.150 (builder@buildhost) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r23809-234f1a2efa) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 Fri Mar 22 22:09:42 2024
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[    0.000000] MIPS: machine is devolo WiFi pro 1200e
[    0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 120816K/131072K available (6082K kernel code, 597K rwdata, 780K rodata, 1236K init, 216K bss, 10256K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] CPU clock: 720.000 MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
[    0.000001] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
[    0.008355] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[    0.075024] pid_max: default: 32768 minimum: 301
[    0.080815] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.088605] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.102785] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.113294] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.120728] pinctrl core: initialized pinctrl subsystem
[    0.127959] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.134807] thermal_sys: Registered thermal governor 'step_wise'
[    0.147411] clocksource: Switched to clocksource MIPS
[    0.160557] NET: Registered PF_INET protocol family
[    0.165941] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.174591] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.183641] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.191904] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.200076] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.207599] TCP: Hash tables configured (established 1024 bind 1024)
[    0.214488] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.221496] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.229300] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.235366] PCI: CLS 0 bytes, default 32
[    0.242443] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    0.254191] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.260460] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.272202] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.283774] pinctrl-single 1804002c.pinmux: 544 pins, size 68
[    0.291023] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.300200] printk: console [ttyS0] disabled
[    0.304811] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 2500000) is a 16550A
[    0.314046] printk: console [ttyS0] enabled
[    0.322947] printk: bootconsole [early0] disabled
[    0.349100] spi-nor spi0.0: mx25l12805d (16384 Kbytes)
[    0.354383] 5 fixed-partitions partitions found on MTD device spi0.0
[    0.360904] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[    0.367666] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[    0.374961] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[    0.381761] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[    0.388731] Creating 5 MTD partitions on "spi0.0":
[    0.393625] 0x000000000000-0x000000040000 : "u-boot"
[    0.403549] 0x000000040000-0x000000050000 : "u-boot-env"
[    0.409864] 0x000000050000-0x000000060000 : "art"
[    0.416934] 0x000000060000-0x000000070000 : "art_bak"
[    0.423108] 0x000000070000-0x000001000000 : "firmware"
[    0.430842] 2 uimage-fw partitions found on MTD device firmware
[    0.436863] Creating 2 MTD partitions on "firmware":
[    0.441933] 0x000000000000-0x000000240000 : "kernel"
[    0.447979] 0x000000240000-0x000000f90000 : "rootfs"
[    0.455171] mtd: setting mtd6 (rootfs) as root device
[    0.460424] 1 squashfs-split partitions found on MTD device rootfs
[    0.466707] 0x000000610000-0x000000f90000 : "rootfs_data"
[    0.938008] ag71xx 19000000.eth: connected to PHY at mdio.0:04 [uid=004dd072, driver=Qualcomm Atheros AR8035]
[    0.948713] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii-rxid
[    1.378170] ag71xx 1a000000.eth: connected to PHY at mdio.1:01 [uid=004dd074, driver=Qualcomm Atheros AR8031/AR8033]
[    1.389482] eth1: Atheros AG71xx at 0xba000000, irq 5, mode: sgmii
[    1.396265] i2c_dev: i2c /dev entries driver
[    1.400788] ath79-wdt 18060008.wdt: unable to register misc device, err=-16
[    1.407891] ath79-wdt: probe of 18060008.wdt failed with error -16
[    1.415962] NET: Registered PF_INET6 protocol family
[    1.428476] Segment Routing with IPv6
[    1.432283] In-situ OAM (IOAM) with IPv6
[    1.436364] NET: Registered PF_PACKET protocol family
[    1.441608] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.455046] 8021q: 802.1Q VLAN Support v1.8
[    1.460470] PCI host bridge to bus 0000:00
[    1.464645] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[    1.471667] pci_bus 0000:00: root bus resource [io  0x0000]
[    1.477321] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.485405] pci 0000:00:00.0: [168c:003c] type 00 class 0x028000
[    1.491550] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    1.498499] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    1.505376] pci 0000:00:00.0: supports D1
[    1.509456] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    1.516331] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    1.523106] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
[    1.530559] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref]
[    1.548336] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[    1.559853] Freeing unused kernel image (initmem) memory: 1236K
[    1.565865] This architecture does not have kernel memory protection.
[    1.572433] Run /sbin/init as init process
[    1.576583]   with arguments:
[    1.576587]     /sbin/init
[    1.576593]   with environment:
[    1.576597]     HOME=/
[    1.576601]     TERM=linux
[    2.249840] init: Console is alive
[    2.253755] init: - watchdog -
[    3.623258] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.698949] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.716780] init: - preinit -
[    5.357217] random: jshn: uninitialized urandom read (4 bytes read)
[    5.799113] random: jshn: uninitialized urandom read (4 bytes read)
[    5.836404] random: jshn: uninitialized urandom read (4 bytes read)
[    8.315503] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[    8.322903] jffs2_build_filesystem(): unlocking the mtd device... 
[    8.322932] done.
[    8.331164] jffs2_build_filesystem(): erasing all blocks after the end marker... 
[   10.259704] eth0: link up (1000Mbps/Full duplex)
[   10.282346] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   49.792213] done.
[   49.794201] jffs2: notice: (395) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   49.811466] mount_root: overlay filesystem has not been fully initialized yet
[   49.824737] mount_root: switching to jffs2 overlay
[   49.832748] overlayfs: upper fs does not support tmpfile.
[   50.340566] urandom-seed: Seed file not found (/etc/urandom.seed)
[   50.469476] eth0: link down
[   50.483511] procd: - early -
[   50.486715] procd: - watchdog -
[   51.226284] procd: - watchdog -
[   51.230102] procd: - ubus -
[   51.360485] random: ubusd: uninitialized urandom read (4 bytes read)
[   51.369595] random: ubusd: uninitialized urandom read (4 bytes read)
[   51.376499] random: ubusd: uninitialized urandom read (4 bytes read)
[   51.386510] procd: - init -
[   52.460790] random: jshn: uninitialized urandom read (4 bytes read)
[   52.522558] random: ubusd: uninitialized urandom read (4 bytes read)
[   52.557784] random: ubus: uninitialized urandom read (4 bytes read)
[   52.603088] kmodloader: loading kernel modules from /etc/modules.d/*
[   53.179005] Loading modules backported from Linux version v6.1.24-0-g0102425ac76b
[   53.186612] Backport generated by backports.git v5.15.92-1-44-gd6ea70fafd36
[   53.851976] PPP generic driver version 2.4.2
[   53.868289] NET: Registered PF_PPPOX protocol family
[   53.930341] ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x3c.
[   53.948427] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002)
[   53.957016] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[   54.931982] urngd: v1.0.2 started.
[   56.777723] random: crng init done
[   56.781192] random: 25 urandom warning(s) missed due to ratelimiting
[   59.423603] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[   59.433020] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   59.444936] ath10k_pci 0000:00:00.0: firmware ver 10.1-ct-8x-__fW-022-ecad3248 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT crc32 3e4cf97f
[   59.567908] ath10k_pci 0000:00:00.0: Loading BDF type 0
[   60.490133] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[   61.504396] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
[   61.521055] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[   61.527371] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424  sw-crypt: 0 ct-sta: 0'
[   61.535536] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 24984 iram: 38672'
[   61.585426] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[   61.598385] ath10k_pci 0000:00:00.0: NOTE:  Firmware DBGLOG output disabled in debug_mask: 0x10000000
[   61.741114] ath: EEPROM regdomain: 0x0
[   61.741132] ath: EEPROM indicates default country code should be used
[   61.741138] ath: doing EEPROM country->regdmn map search
[   61.741151] ath: country maps to regdmn code: 0x3a
[   61.741159] ath: Country alpha2 being used: US
[   61.741165] ath: Regpair used: 0x3a
[   61.824160] ath: EEPROM regdomain: 0x0
[   61.824181] ath: EEPROM indicates default country code should be used
[   61.824186] ath: doing EEPROM country->regdmn map search
[   61.824200] ath: country maps to regdmn code: 0x3a
[   61.824207] ath: Country alpha2 being used: US
[   61.824214] ath: Regpair used: 0x3a
[   61.839791] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[   61.841623] ieee80211 phy1: Atheros AR9550 Rev:0 mem=0xb8100000, irq=13
[   61.927896] kmodloader: done loading kernel modules from /etc/modules.d/*
[   82.431021] br-lan: port 1(eth0) entered blocking state
[   82.436343] br-lan: port 1(eth0) entered disabled state
[   82.441967] device eth0 entered promiscuous mode
[   82.490487] br-lan: port 2(eth1) entered blocking state
[   82.495804] br-lan: port 2(eth1) entered disabled state
[   82.501405] device eth1 entered promiscuous mode
[   84.551377] ath: EEPROM regdomain: 0x8114
[   84.555460] ath: EEPROM indicates we should expect a country code
[   84.561687] ath: doing EEPROM country->regdmn map search
[   84.567075] ath: country maps to regdmn code: 0x37
[   84.571945] ath: Country alpha2 being used: DE
[   84.576446] ath: Regpair used: 0x37
[   84.579993] ath: regdomain 0x8114 dynamically updated by user
[   84.585898] ath: EEPROM regdomain: 0x8114
[   84.589981] ath: EEPROM indicates we should expect a country code
[   84.596167] ath: doing EEPROM country->regdmn map search
[   84.601565] ath: country maps to regdmn code: 0x37
[   84.606419] ath: Country alpha2 being used: DE
[   84.610934] ath: Regpair used: 0x37
[   84.614471] ath: regdomain 0x8114 dynamically updated by user
[   85.538823] eth0: link up (1000Mbps/Full duplex)
[   85.543547] br-lan: port 1(eth0) entered blocking state
[   85.548883] br-lan: port 1(eth0) entered forwarding state
[   85.558727] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   88.132110] br-lan: port 3(phy1-ap0) entered blocking state
[   88.137822] br-lan: port 3(phy1-ap0) entered disabled state
[   88.143740] device phy1-ap0 entered promiscuous mode
[   90.598162] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
[   90.615063] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[   90.621831] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424  sw-crypt: 0 ct-sta: 0'
[   90.630027] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 24984 iram: 38672'
[   90.722860] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
[   90.764682] ath10k_pci 0000:00:00.0: rts threshold -1
[   90.773394] br-lan: port 4(phy0-ap0) entered blocking state
[   90.779118] br-lan: port 4(phy0-ap0) entered disabled state
[   90.785036] device phy0-ap0 entered promiscuous mode
[   97.328999] IPv6: ADDRCONF(NETDEV_CHANGE): phy1-ap0: link becomes ready
[   97.335881] br-lan: port 3(phy1-ap0) entered blocking state
[   97.341589] br-lan: port 3(phy1-ap0) entered forwarding state
[  108.620694] IPv6: ADDRCONF(NETDEV_CHANGE): phy0-ap0: link becomes ready
[  108.627623] br-lan: port 4(phy0-ap0) entered blocking state
[  108.633320] br-lan: port 4(phy0-ap0) entered forwarding state
[  143.699532] ath10k_pci 0000:00:00.0: mac flush vdev 0 drop 0 queues 0x1 ar->paused: 0x0  arvif->paused: 0x0
[  194.116705] ath10k_pci 0000:00:00.0: mac flush vdev 0 drop 0 queues 0x1 ar->paused: 0x0  arvif->paused: 0x0
[  286.170974] ath10k_pci 0000:00:00.0: mac flush vdev 0 drop 0 queues 0x1 ar->paused: 0x0  arvif->paused: 0x0
[  286.495002] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  286.597417] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  286.699812] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  286.802213] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  286.904614] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  287.007012] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  287.109416] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  287.211819] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  287.314212] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  287.416619] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  287.519011] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  287.621410] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  287.723812] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  287.826215] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  287.928613] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  288.031017] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  288.133412] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  288.235809] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  288.338210] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  288.440605] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  288.543011] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  288.645409] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  288.747808] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  288.850202] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  288.952602] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  289.054998] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  289.157409] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  289.259802] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  289.362209] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  289.376421] ath10k_pci 0000:00:00.0: Cannot communicate with firmware, previous wmi cmds: 36954:-1354 36904:-1366 36904:-1366 36904:-1366, jiffies: -1064, attempting restart restart firmware, dev-flags: 0 x142
[  289.395434] ath10k_pci 0000:00:00.0: failed to transmit management frame via WMI: -11
[  289.403455] ath10k_pci 0000:00:00.0: failed to transmit management frame via WMI: -143
[  289.411553] ath10k_pci 0000:00:00.0: failed to transmit management frame via WMI: -143
[  289.419643] ath10k_pci 0000:00:00.0: failed to transmit management frame via WMI: -143
[  289.427727] ath10k_pci 0000:00:00.0: failed to transmit management frame via WMI: -143
[  289.435900] ath10k_pci 0000:00:00.0: failed to transmit management frame via WMI: -143
[  289.444021] ath10k_pci 0000:00:00.0: failed to transmit management frame via WMI: -143
[  289.464615] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  289.536463] ath10k_pci 0000:00:00.0: failed to send wmi nop: -143
[  289.542670] ath10k_pci 0000:00:00.0: could not request stats (type -268435456 ret -143 specifier 1)
[  289.552388] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request: -143
[  289.561675] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer 7794af8d vdev: 0 addr: 38:f9:d3:19:85:f8 
[  289.572900] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer b88e1568 vdev: 0 addr: f4:06:8d:df:27:4d 
[  289.584102] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  289.721958] ieee80211 phy0: Hardware restart was requested
[  290.693848] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
[  290.710522] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[  290.716905] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424  sw-crypt: 0 ct-sta: 0'
[  290.725044] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 24984 iram: 38672'
[  290.789294] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
[  290.796671] ath10k_pci 0000:00:00.0: set-coverage-class, phyclk: 88  value: 0
[  290.804541] ath10k_pci 0000:00:00.0: rts threshold -1
[  290.819707] ath10k_pci 0000:00:00.0: device successfully recovered
[  291.189926] ath10k_pci 0000:00:00.0: mac flush vdev 0 drop 0 queues 0x1 ar->paused: 0x0  arvif->paused: 0x0
[  291.256936] ath10k_pci 0000:00:00.0: mac flush vdev 0 drop 0 queues 0x1 ar->paused: 0x0  arvif->paused: 0x0
[  307.491945] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  307.594346] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  307.696738] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  307.799145] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  307.901542] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  308.003934] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  308.106342] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  308.208732] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  308.311125] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  308.413541] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  308.515937] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  308.618338] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  308.720730] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  308.823126] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  308.925535] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  309.027938] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  309.130331] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  309.232732] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  309.335116] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  309.437532] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  309.539938] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  309.642336] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  309.744729] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  309.847132] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  309.949536] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  310.051931] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  310.154334] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  310.256738] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  310.359131] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  310.461533] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  310.496433] ath10k_pci 0000:00:00.0: Cannot communicate with firmware, previous wmi cmds: 36954:742 36904:728 36952:728 40859:728, jiffies: 1048, attempting restart restart firmware, dev-flags: 0 x142
[  310.514677] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request: -143
[  310.523279] ath10k_pci 0000:00:00.0: failed to send wmi nop: -143
[  310.529845] ath10k_pci 0000:00:00.0: could not request stats (type -268435456 ret -143 specifier 1)
[  310.541570] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -143
[  310.549073] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -143
[  310.557724] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer fb5c7a4b vdev: 0 addr: f4:06:8d:df:27:4d 
[  310.568991] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
[  310.710515] ieee80211 phy0: Hardware restart was requested
[  310.716241] ath10k_pci 0000:00:00.0: failed to set cts protection for vdev 0: -143
[  310.723942] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -143
[  310.732557] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -143
[  310.740002] ath10k_pci 0000:00:00.0: failed to set mgmt tx rate -143
[  311.715197] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
[  311.731870] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[  311.738247] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424  sw-crypt: 0 ct-sta: 0'
[  311.746442] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 24984 iram: 38672'
[  311.811185] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
[  311.825358] ath10k_pci 0000:00:00.0: rts threshold -1
[  311.839425] ath10k_pci 0000:00:00.0: device successfully recovered
[  466.151857] ath10k_pci 0000:00:00.0: mac flush vdev 0 drop 0 queues 0x1 ar->paused: 0x0  arvif->paused: 0x0

a shortened system.log:

Jun  1 19:14:50 kern.notice kernel: [    0.000000] Linux version 5.15.150 (builder@buildhost) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r23809-234f1a2efa) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 Fri Mar 22 22:09:42 2024
Jun  1 19:14:50 kern.debug kernel: [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Jun  1 19:14:50 kern.debug kernel: [    0.000000] pcpu-alloc: [0] 0
Jun  1 19:14:50 kern.notice kernel: [    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
Jun  1 19:14:50 kern.notice kernel: [    0.354383] 5 fixed-partitions partitions found on MTD device spi0.0
Jun  1 19:14:50 kern.err kernel: [    0.360904] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
Jun  1 19:14:50 kern.err kernel: [    0.367666] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
Jun  1 19:14:50 kern.err kernel: [    0.374961] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
Jun  1 19:14:50 kern.err kernel: [    0.381761] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
Jun  1 19:14:50 kern.notice kernel: [    0.388731] Creating 5 MTD partitions on "spi0.0":
Jun  1 19:14:50 kern.notice kernel: [    0.393625] 0x000000000000-0x000000040000 : "u-boot"
Jun  1 19:14:50 kern.notice kernel: [    0.403549] 0x000000040000-0x000000050000 : "u-boot-env"
Jun  1 19:14:50 kern.notice kernel: [    0.409864] 0x000000050000-0x000000060000 : "art"
Jun  1 19:14:50 kern.notice kernel: [    0.416934] 0x000000060000-0x000000070000 : "art_bak"
Jun  1 19:14:50 kern.notice kernel: [    0.423108] 0x000000070000-0x000001000000 : "firmware"
Jun  1 19:14:50 kern.notice kernel: [    0.430842] 2 uimage-fw partitions found on MTD device firmware
Jun  1 19:14:50 kern.notice kernel: [    0.436863] Creating 2 MTD partitions on "firmware":
Jun  1 19:14:50 kern.notice kernel: [    0.441933] 0x000000000000-0x000000240000 : "kernel"
Jun  1 19:14:50 kern.notice kernel: [    0.447979] 0x000000240000-0x000000f90000 : "rootfs"
Jun  1 19:14:50 kern.notice kernel: [    0.460424] 1 squashfs-split partitions found on MTD device rootfs
Jun  1 19:14:50 kern.notice kernel: [    0.466707] 0x000000610000-0x000000f90000 : "rootfs_data"
Jun  1 19:14:50 kern.err kernel: [    1.400788] ath79-wdt 18060008.wdt: unable to register misc device, err=-16
Jun  1 19:14:50 kern.warn kernel: [    1.407891] ath79-wdt: probe of 18060008.wdt failed with error -16
Jun  1 19:14:50 kern.warn kernel: [    1.565865] This architecture does not have kernel memory protection.
Jun  1 19:14:50 kern.debug kernel: [    1.576583]   with arguments:
Jun  1 19:14:50 kern.debug kernel: [    1.576587]     /sbin/init
Jun  1 19:14:50 kern.debug kernel: [    1.576593]   with environment:
Jun  1 19:14:50 kern.debug kernel: [    1.576597]     HOME=/
Jun  1 19:14:50 kern.debug kernel: [    1.576601]     TERM=linux
Jun  1 19:14:50 kern.notice kernel: [    5.357217] random: jshn: uninitialized urandom read (4 bytes read)
Jun  1 19:14:50 kern.notice kernel: [    5.799113] random: jshn: uninitialized urandom read (4 bytes read)
Jun  1 19:14:50 kern.notice kernel: [    5.836404] random: jshn: uninitialized urandom read (4 bytes read)
Jun  1 19:14:50 kern.warn kernel: [    8.315503] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
Jun  1 19:14:50 kern.warn kernel: [    8.322903] jffs2_build_filesystem(): unlocking the mtd device...
Jun  1 19:14:50 kern.warn kernel: [    8.322932] done.
Jun  1 19:14:50 kern.warn kernel: [    8.331164] jffs2_build_filesystem(): erasing all blocks after the end marker...
Jun  1 19:14:50 kern.warn kernel: [   49.792213] done.
Jun  1 19:14:50 kern.notice kernel: [   49.794201] jffs2: notice: (395) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Jun  1 19:14:50 kern.warn kernel: [   49.832748] overlayfs: upper fs does not support tmpfile.
Jun  1 19:14:50 user.warn kernel: [   50.340566] urandom-seed: Seed file not found (/etc/urandom.seed)
Jun  1 19:14:50 kern.notice kernel: [   51.360485] random: ubusd: uninitialized urandom read (4 bytes read)
Jun  1 19:14:50 kern.notice kernel: [   51.369595] random: ubusd: uninitialized urandom read (4 bytes read)
Jun  1 19:14:50 kern.notice kernel: [   51.376499] random: ubusd: uninitialized urandom read (4 bytes read)
Jun  1 19:14:50 kern.notice kernel: [   56.777723] random: crng init done
Jun  1 19:14:50 kern.notice kernel: [   56.781192] random: 25 urandom warning(s) missed due to ratelimiting
Jun  1 19:14:50 kern.warn kernel: [   61.504396] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
Jun  1 19:14:50 kern.debug kernel: [   61.741114] ath: EEPROM regdomain: 0x0
Jun  1 19:14:50 kern.debug kernel: [   61.741132] ath: EEPROM indicates default country code should be used
Jun  1 19:14:50 kern.debug kernel: [   61.741138] ath: doing EEPROM country->regdmn map search
Jun  1 19:14:50 kern.debug kernel: [   61.741151] ath: country maps to regdmn code: 0x3a
Jun  1 19:14:50 kern.debug kernel: [   61.741159] ath: Country alpha2 being used: US
Jun  1 19:14:50 kern.debug kernel: [   61.741165] ath: Regpair used: 0x3a
Jun  1 19:14:50 kern.debug kernel: [   61.824160] ath: EEPROM regdomain: 0x0
Jun  1 19:14:50 kern.debug kernel: [   61.824181] ath: EEPROM indicates default country code should be used
Jun  1 19:14:50 kern.debug kernel: [   61.824186] ath: doing EEPROM country->regdmn map search
Jun  1 19:14:50 kern.debug kernel: [   61.824200] ath: country maps to regdmn code: 0x3a
Jun  1 19:14:50 kern.debug kernel: [   61.824207] ath: Country alpha2 being used: US
Jun  1 19:14:50 kern.debug kernel: [   61.824214] ath: Regpair used: 0x3a
Jun  1 19:14:50 kern.debug kernel: [   61.839791] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
Jun  1 19:14:52 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Jun  1 19:14:52 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Jun  1 19:14:53 daemon.warn dnsmasq[1]: no servers found in /tmp/resolv.conf.d/resolv.conf.auto, will retry
Jun  1 19:14:57 daemon.notice wpa_supplicant[1624]: Successfully initialized wpa_supplicant
Jun  1 19:14:58 user.notice : Added device handler type: bonding
Jun  1 19:14:58 user.notice : Added device handler type: 8021ad
Jun  1 19:14:58 user.notice : Added device handler type: 8021q
Jun  1 19:14:58 user.notice : Added device handler type: macvlan
Jun  1 19:14:58 user.notice : Added device handler type: veth
Jun  1 19:14:58 user.notice : Added device handler type: bridge
Jun  1 19:14:58 user.notice : Added device handler type: Network device
Jun  1 19:14:58 user.notice : Added device handler type: tunnel
Jun  1 19:15:01 user.notice ucitrack: Setting up /etc/config/dhcp reload dependency on /etc/config/network
Jun  1 19:15:01 user.notice ucitrack: Setting up /etc/config/network reload dependency on /etc/config/wireless
Jun  1 19:15:02 user.notice ucitrack: Setting up /etc/config/luci-splash reload dependency on /etc/config/firewall
Jun  1 19:15:02 user.notice ucitrack: Setting up /etc/config/qos reload dependency on /etc/config/firewall
Jun  1 19:15:02 user.notice ucitrack: Setting up /etc/config/miniupnpd reload dependency on /etc/config/firewall
Jun  1 19:15:02 user.notice ucitrack: Setting up /etc/config/odhcpd reload dependency on /etc/config/dhcp
Jun  1 19:15:03 user.notice ucitrack: Setting up non-init /etc/config/fstab reload handler: /sbin/block mount
Jun  1 19:15:03 user.notice ucitrack: Setting up /etc/config/system reload trigger for non-procd /etc/init.d/led
Jun  1 19:15:03 user.notice ucitrack: Setting up /etc/config/luci_statistics reload dependency on /etc/config/system
Jun  1 19:15:03 user.notice ucitrack: Setting up /etc/config/dhcp reload dependency on /etc/config/system
Jun  1 19:15:05 daemon.warn netifd: You have delegated IPv6-prefixes but haven't assigned them to any interface. Did you forget to set option ip6assign on your lan-interfaces?
Jun  1 19:15:05 daemon.notice netifd: Interface 'lan' is enabled
Jun  1 19:15:05 daemon.notice netifd: Interface 'loopback' is enabled
Jun  1 19:15:05 daemon.notice netifd: Interface 'loopback' is setting up now
Jun  1 19:15:05 daemon.notice netifd: Interface 'loopback' is now up
Jun  1 19:15:05 daemon.notice netifd: Network device 'lo' link is up
Jun  1 19:15:05 daemon.notice netifd: Interface 'loopback' has link connectivity
Jun  1 19:15:06 daemon.notice netifd: radio1 (2253): WARNING: Variable 'data' does not exist or is not an array/object
Jun  1 19:15:06 daemon.notice netifd: radio0 (2252): WARNING: Variable 'data' does not exist or is not an array/object
Jun  1 19:15:07 kern.debug kernel: [   84.551377] ath: EEPROM regdomain: 0x8114
Jun  1 19:15:07 kern.debug kernel: [   84.555460] ath: EEPROM indicates we should expect a country code
Jun  1 19:15:07 kern.debug kernel: [   84.561687] ath: doing EEPROM country->regdmn map search
Jun  1 19:15:07 kern.debug kernel: [   84.567075] ath: country maps to regdmn code: 0x37
Jun  1 19:15:07 kern.debug kernel: [   84.571945] ath: Country alpha2 being used: DE
Jun  1 19:15:07 kern.debug kernel: [   84.576446] ath: Regpair used: 0x37
Jun  1 19:15:07 kern.debug kernel: [   84.579993] ath: regdomain 0x8114 dynamically updated by user
Jun  1 19:15:07 kern.debug kernel: [   84.585898] ath: EEPROM regdomain: 0x8114
Jun  1 19:15:07 kern.debug kernel: [   84.589981] ath: EEPROM indicates we should expect a country code
Jun  1 19:15:07 kern.debug kernel: [   84.596167] ath: doing EEPROM country->regdmn map search
Jun  1 19:15:07 kern.debug kernel: [   84.601565] ath: country maps to regdmn code: 0x37
Jun  1 19:15:07 kern.debug kernel: [   84.606419] ath: Country alpha2 being used: DE
Jun  1 19:15:07 kern.debug kernel: [   84.610934] ath: Regpair used: 0x37
Jun  1 19:15:07 kern.debug kernel: [   84.614471] ath: regdomain 0x8114 dynamically updated by user
Jun  1 19:15:08 daemon.notice netifd: Network device 'eth0' link is up
Jun  1 19:15:08 daemon.notice netifd: bridge 'br-lan' link is up
Jun  1 19:15:08 daemon.notice netifd: Interface 'lan' has link connectivity
Jun  1 19:15:08 daemon.notice netifd: Interface 'lan' is setting up now
Jun  1 19:15:08 daemon.notice hostapd: Set new config for phy phy1:
Jun  1 19:15:08 daemon.notice wpa_supplicant[1624]: Set new config for phy phy1
Jun  1 19:15:08 daemon.notice hostapd: Set new config for phy phy0:
Jun  1 19:15:08 daemon.notice wpa_supplicant[1624]: Set new config for phy phy0
Jun  1 19:15:08 daemon.notice netifd: lan (2462): udhcpc: started, v1.36.1
Jun  1 19:15:09 daemon.notice netifd: lan (2462): udhcpc: broadcasting discover
Jun  1 19:15:09 daemon.notice netifd: lan (2462): udhcpc: broadcasting select for 192.168.3.2, server 192.168.3.1
Jun  1 19:15:09 daemon.notice netifd: lan (2462): udhcpc: lease of 192.168.3.2 obtained from 192.168.3.1, lease time 4294967295
Jun  1 19:15:10 daemon.notice netifd: Interface 'lan' is now up
Jun  1 19:15:10 daemon.notice wpa_supplicant[1624]: Set new config for phy phy1
Jun  1 19:15:10 daemon.notice wpa_supplicant[1624]: Set new config for phy phy0
Jun  1 19:15:11 daemon.notice hostapd: Set new config for phy phy1: /var/run/hostapd-phy1.conf
Jun  1 19:15:11 daemon.notice hostapd: Restart interface for phy phy1
Jun  1 19:15:11 daemon.notice hostapd: Configuration file: data: driver=nl80211 logger_syslog=127 logger_syslog_level=2 logger_stdout=127 logger_stdout_level=2 country_code=DE ieee80211d=1 hw_mode=g supported_rates=60 90 120 180 240 360 480 540 basic_rates=60 120 240 beacon_int=100 #num_global_macaddr=1 ieee80211n=1 ht_coex=0 ht_capab=[LDPC][SHORT-GI-20][SHORT-GI-40][TX-STBC][RX-STBC1][DSSS_CCK-40] channel=acs_survey  interface=phy1-ap0 bssid=f4:06:8d:df:27:4c ctrl_interface=/var/run/hostapd ap_isolate=1 bss_load_update_period=60 chan_util_avg_period=600 disassoc_low_ack=1 skip_inactivity_poll=0 preamble=1 wmm_enabled=1 ignore_broadcast_ssid=0 uapsd_advertisement_enabled=1 utf8_ssid=1 multi_ap=0 sae_require_mfp=1 sae_pwe=2 wpa_passphrase=@J`.cC,#AZjXVT+%d85RWSNq6 wpa_psk_file=/var/run/hostapd-phy1-ap0.psk auth_algs=1 wpa=2 wpa_pairwise=CCMP ssid=Hiddensee bridge=br-lan wds_bridge= snoop_iface=br-lan wpa_disable_eapol_key_retries=0 wpa_key_mgmt=WPA-PSK WPA-PSK-SHA256 SAE okc=1 ieee80211w=1 group_mgmt_cipher=AES-128-CMA
Jun  1 19:15:11 daemon.notice hostapd: phy1-ap0: interface state UNINITIALIZED->COUNTRY_UPDATE
Jun  1 19:15:11 daemon.notice hostapd: ACS: Automatic channel selection started, this may take a bit
Jun  1 19:15:11 daemon.notice hostapd: phy1-ap0: interface state COUNTRY_UPDATE->ACS
Jun  1 19:15:11 daemon.notice hostapd: phy1-ap0: ACS-STARTED
Jun  1 19:15:11 daemon.notice hostapd: Set new config for phy phy0: /var/run/hostapd-phy0.conf
Jun  1 19:15:11 daemon.notice hostapd: Restart interface for phy phy0
Jun  1 19:15:11 daemon.notice netifd: lan (2462): udhcpc: sending renew to server 192.168.3.1
Jun  1 19:15:11 daemon.notice netifd: lan (2462): udhcpc: lease of 192.168.3.2 obtained from 192.168.3.1, lease time 4294967295
Jun  1 19:15:11 daemon.notice hostapd: Configuration file: data: driver=nl80211 logger_syslog=127 logger_syslog_level=2 logger_stdout=127 logger_stdout_level=2 country_code=DE ieee80211d=1 ieee80211h=1 hw_mode=a beacon_int=100 tx_queue_data2_burst=2.0 #num_global_macaddr=1 ieee80211n=1 ht_coex=0 ht_capab=[HT40+][LDPC][SHORT-GI-20][SHORT-GI-40][TX-STBC][RX-STBC1][MAX-AMSDU-7935][DSSS_CCK-40] ieee80211ac=1 vht_oper_chwidth=1 vht_oper_centr_freq_seg0_idx=-6 vht_capab=[RXLDPC][SHORT-GI-80][TX-STBC-2BY1][RX-ANTENNA-PATTERN][TX-ANTENNA-PATTERN][RX-STBC-1][MAX-MPDU-11454][MAX-A-MPDU-LEN-EXP7] channel=acs_survey  interface=phy0-ap0 bssid=f4:06:8d:df:27:4d ctrl_interface=/var/run/hostapd ap_isolate=1 bss_load_update_period=60 chan_util_avg_period=600 disassoc_low_ack=1 skip_inactivity_poll=0 preamble=1 wmm_enabled=1 ignore_broadcast_ssid=0 uapsd_advertisement_enabled=1 utf8_ssid=1 multi_ap=0 sae_require_mfp=1 sae_pwe=2 wpa_passphrase=@J`.cC,#AZjXVT+%d85RWSNq6 wpa_psk_file=/var/run/hostapd-phy0-ap0.psk auth_algs=1 wpa=2 wpa_pai
Jun  1 19:15:12 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Jun 12 22:37:45 kern.warn kernel: [   90.598162] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
Jun 12 22:37:45 kern.warn kernel: [   90.722860] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
Jun 12 22:37:45 daemon.notice hostapd: phy0-ap0: interface state UNINITIALIZED->COUNTRY_UPDATE
Jun 12 22:37:45 daemon.notice hostapd: ACS: Automatic channel selection started, this may take a bit
Jun 12 22:37:45 daemon.notice hostapd: phy0-ap0: interface state COUNTRY_UPDATE->ACS
Jun 12 22:37:45 daemon.notice hostapd: phy0-ap0: ACS-STARTED
Jun 12 22:37:46 daemon.notice netifd: Wireless device 'radio1' is now up
Jun 12 22:37:46 daemon.notice netifd: lan (2462): udhcpc: sending renew to server 192.168.3.1
Jun 12 22:37:46 daemon.notice netifd: lan (2462): udhcpc: lease of 192.168.3.2 obtained from 192.168.3.1, lease time 4294967295
Jun 12 22:37:46 daemon.notice netifd: Wireless device 'radio0' is now up
Jun 12 22:37:52 daemon.notice hostapd: phy1-ap0: ACS-COMPLETED freq=2437 channel=6
Jun 12 22:37:52 daemon.notice netifd: Network device 'phy1-ap0' link is up
Jun 12 22:37:52 daemon.notice hostapd: phy1-ap0: interface state ACS->ENABLED
Jun 12 22:37:52 daemon.notice hostapd: phy1-ap0: AP-ENABLED
Jun 12 22:37:53 daemon.notice hostapd: phy1-ap0: AP-STA-CONNECTED d8:49:2f:8c:03:95 auth_alg=open
Jun 12 22:37:53 daemon.notice hostapd: phy1-ap0: EAPOL-4WAY-HS-COMPLETED d8:49:2f:8c:03:95
Jun 12 22:37:57 daemon.notice hostapd: phy1-ap0: AP-STA-CONNECTED b0:4a:39:2e:51:ed auth_alg=open
Jun 12 22:37:57 daemon.notice hostapd: phy1-ap0: EAPOL-4WAY-HS-COMPLETED b0:4a:39:2e:51:ed
Jun 12 22:38:00 daemon.notice hostapd: phy0-ap0: ACS-COMPLETED freq=5805 channel=161
Jun 12 22:38:00 daemon.notice hostapd: phy0-ap0: interface state ACS->HT_SCAN
Jun 12 22:38:02 daemon.notice hostapd: phy1-ap0: AP-STA-CONNECTED 58:24:29:e1:c2:bb auth_alg=sae
Jun 12 22:38:02 daemon.notice hostapd: phy1-ap0: EAPOL-4WAY-HS-COMPLETED 58:24:29:e1:c2:bb
Jun 12 22:38:03 daemon.notice netifd: Network device 'phy0-ap0' link is up
Jun 12 22:38:03 daemon.notice hostapd: phy0-ap0: interface state HT_SCAN->ENABLED
Jun 12 22:38:03 daemon.notice hostapd: phy0-ap0: AP-ENABLED
Jun 12 22:38:06 daemon.notice hostapd: phy1-ap0: AP-STA-CONNECTED 38:f9:d3:19:85:f8 auth_alg=sae
Jun 12 22:38:06 daemon.notice hostapd: phy1-ap0: EAPOL-4WAY-HS-COMPLETED 38:f9:d3:19:85:f8
Jun 12 22:38:11 daemon.notice hostapd: phy1-ap0: Prune association for 38:f9:d3:19:85:f8
Jun 12 22:38:11 daemon.notice hostapd: phy1-ap0: AP-STA-DISCONNECTED 38:f9:d3:19:85:f8
Jun 12 22:38:11 daemon.notice hostapd: phy0-ap0: AP-STA-CONNECTED 38:f9:d3:19:85:f8 auth_alg=sae
Jun 12 22:38:11 daemon.notice hostapd: phy0-ap0: EAPOL-4WAY-HS-COMPLETED 38:f9:d3:19:85:f8
Jun 12 22:38:12 daemon.notice hostapd: phy1-ap0: AP-STA-CONNECTED 98:7b:f3:b8:dd:1c auth_alg=open
Jun 12 22:38:12 daemon.notice hostapd: phy1-ap0: EAPOL-4WAY-HS-COMPLETED 98:7b:f3:b8:dd:1c
Jun 12 22:38:31 daemon.notice hostapd: phy1-ap0: Prune association for 58:24:29:e1:c2:bb
Jun 12 22:38:31 daemon.notice hostapd: phy1-ap0: AP-STA-DISCONNECTED 58:24:29:e1:c2:bb
Jun 12 22:38:31 daemon.notice hostapd: phy0-ap0: AP-STA-CONNECTED 58:24:29:e1:c2:bb auth_alg=sae
Jun 12 22:38:31 daemon.notice hostapd: phy0-ap0: EAPOL-4WAY-HS-COMPLETED 58:24:29:e1:c2:bb
Jun 12 22:38:36 daemon.notice hostapd: phy0-ap0: Prune association for 58:24:29:e1:c2:bb
Jun 12 22:38:36 daemon.notice hostapd: phy0-ap0: AP-STA-DISCONNECTED 58:24:29:e1:c2:bb
Jun 12 22:38:36 daemon.notice hostapd: phy1-ap0: AP-STA-CONNECTED 58:24:29:e1:c2:bb auth_alg=sae
Jun 12 22:38:36 daemon.notice hostapd: phy1-ap0: EAPOL-4WAY-HS-COMPLETED 58:24:29:e1:c2:bb
Jun 12 22:38:40 daemon.notice hostapd: phy1-ap0: Prune association for 58:24:29:e1:c2:bb
Jun 12 22:38:40 daemon.notice hostapd: phy1-ap0: AP-STA-DISCONNECTED 58:24:29:e1:c2:bb
Jun 12 22:38:40 daemon.notice hostapd: phy0-ap0: AP-STA-CONNECTED 58:24:29:e1:c2:bb auth_alg=open
Jun 12 22:38:40 daemon.notice hostapd: phy0-ap0: EAPOL-4WAY-HS-COMPLETED 58:24:29:e1:c2:bb
Jun 12 22:39:23 daemon.notice hostapd: phy0-ap0: AP-STA-CONNECTED a2:a6:62:0a:c0:18 auth_alg=sae
Jun 12 22:39:23 daemon.notice hostapd: phy0-ap0: EAPOL-4WAY-HS-COMPLETED a2:a6:62:0a:c0:18
Jun 12 22:39:27 daemon.notice hostapd: phy0-ap0: Prune association for a2:a6:62:0a:c0:18
Jun 12 22:39:27 daemon.notice hostapd: phy0-ap0: AP-STA-DISCONNECTED a2:a6:62:0a:c0:18
Jun 12 22:39:27 daemon.notice hostapd: phy1-ap0: AP-STA-CONNECTED a2:a6:62:0a:c0:18 auth_alg=sae
Jun 12 22:39:27 daemon.notice hostapd: phy1-ap0: EAPOL-4WAY-HS-COMPLETED a2:a6:62:0a:c0:18
Jun 12 22:40:17 daemon.err uhttpd[1917]: [info] luci: accepted login on / for root from 192.168.3.8
Jun 12 22:41:01 daemon.notice hostapd: phy0-ap0: AP-STA-DISCONNECTED 58:24:29:e1:c2:bb
Jun 12 22:41:01 kern.warn kernel: [  286.495002] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Jun 12 22:41:01 kern.warn kernel: [  286.597417] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Jun 12 22:41:01 kern.warn kernel: [  286.699812] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Jun 12 22:41:01 kern.warn kernel: [  286.802213] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Jun 12 22:41:01 kern.warn kernel: [  286.904614] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Jun 12 22:41:01 kern.warn kernel: [  287.007012] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Jun 12 22:41:02 kern.warn kernel: [  287.109416] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Jun 12 22:41:02 kern.warn kernel: [  287.211819] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Jun 12 22:41:04 kern.err kernel: [  289.376421] ath10k_pci 0000:00:00.0: Cannot communicate with firmware, previous wmi cmds: 36954:-1354 36904:-1366 36904:-1366 36904:-1366, jiffies: -1064, attempting restart restart firmware, dev-flags: 0 x142
Jun 12 22:41:04 kern.warn kernel: [  289.395434] ath10k_pci 0000:00:00.0: failed to transmit management frame via WMI: -11
Jun 12 22:41:04 kern.warn kernel: [  289.403455] ath10k_pci 0000:00:00.0: failed to transmit management frame via WMI: -143
Jun 12 22:41:04 kern.warn kernel: [  289.411553] ath10k_pci 0000:00:00.0: failed to transmit management frame via WMI: -143
Jun 12 22:41:04 kern.warn kernel: [  289.419643] ath10k_pci 0000:00:00.0: failed to transmit management frame via WMI: -143
Jun 12 22:41:04 kern.warn kernel: [  289.464615] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Jun 12 22:41:04 kern.warn kernel: [  289.536463] ath10k_pci 0000:00:00.0: failed to send wmi nop: -143
Jun 12 22:41:04 kern.warn kernel: [  289.542670] ath10k_pci 0000:00:00.0: could not request stats (type -268435456 ret -143 specifier 1)
Jun 12 22:41:04 kern.warn kernel: [  289.552388] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request: -143
Jun 12 22:41:04 kern.warn kernel: [  289.561675] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer 7794af8d vdev: 0 addr: 38:f9:d3:19:85:f8
Jun 12 22:41:04 kern.warn kernel: [  289.572900] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer b88e1568 vdev: 0 addr: f4:06:8d:df:27:4d
Jun 12 22:41:04 kern.warn kernel: [  289.584102] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Jun 12 22:41:05 kern.warn kernel: [  290.693848] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
Jun 12 22:41:05 kern.warn kernel: [  290.789294] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
Jun 12 22:41:05 kern.warn kernel: [  290.796671] ath10k_pci 0000:00:00.0: set-coverage-class, phyclk: 88  value: 0
Jun 12 22:41:05 daemon.notice hostapd: phy0-ap0: AP-STA-DISCONNECTED 38:f9:d3:19:85:f8
Jun 12 22:41:06 daemon.err hostapd: nl80211: NL80211_ATTR_STA_VLAN (addr=38:f9:d3:19:85:f8 ifname=phy0-ap0 vlan_id=0) failed: -2 (No such file or directory)
Jun 12 22:41:06 daemon.notice hostapd: phy1-ap0: AP-STA-CONNECTED 58:24:29:e1:c2:bb auth_alg=sae
Jun 12 22:41:06 daemon.notice hostapd: phy1-ap0: EAPOL-4WAY-HS-COMPLETED 58:24:29:e1:c2:bb
Jun 12 22:41:12 daemon.notice hostapd: phy1-ap0: AP-STA-CONNECTED 38:f9:d3:19:85:f8 auth_alg=open
Jun 12 22:41:12 daemon.notice hostapd: phy1-ap0: EAPOL-4WAY-HS-COMPLETED 38:f9:d3:19:85:f8
Jun 12 22:41:22 kern.warn kernel: [  307.491945] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Jun 12 22:41:22 kern.warn kernel: [  307.594346] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Jun 12 22:41:22 kern.warn kernel: [  307.696738] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Jun 12 22:41:22 kern.warn kernel: [  307.799145] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Jun 12 22:41:25 kern.err kernel: [  310.496433] ath10k_pci 0000:00:00.0: Cannot communicate with firmware, previous wmi cmds: 36954:742 36904:728 36952:728 40859:728, jiffies: 1048, attempting restart restart firmware, dev-flags: 0 x142
Jun 12 22:41:25 kern.warn kernel: [  310.514677] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request: -143
Jun 12 22:41:25 kern.warn kernel: [  310.523279] ath10k_pci 0000:00:00.0: failed to send wmi nop: -143
Jun 12 22:41:25 kern.warn kernel: [  310.529845] ath10k_pci 0000:00:00.0: could not request stats (type -268435456 ret -143 specifier 1)
Jun 12 22:41:25 kern.warn kernel: [  310.541570] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -143
Jun 12 22:41:25 kern.warn kernel: [  310.549073] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -143
Jun 12 22:41:25 kern.warn kernel: [  310.557724] ath10k_pci 0000:00:00.0: removing peer, cleanup-all, deleting: peer fb5c7a4b vdev: 0 addr: f4:06:8d:df:27:4d
Jun 12 22:41:25 kern.warn kernel: [  310.568991] ath10k_pci 0000:00:00.0: SWBA overrun on vdev 0, skipped old beacon
Jun 12 22:41:25 kern.warn kernel: [  310.716241] ath10k_pci 0000:00:00.0: failed to set cts protection for vdev 0: -143
Jun 12 22:41:25 kern.warn kernel: [  310.723942] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -143
Jun 12 22:41:25 kern.warn kernel: [  310.732557] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -143
Jun 12 22:41:25 kern.warn kernel: [  310.740002] ath10k_pci 0000:00:00.0: failed to set mgmt tx rate -143
Jun 12 22:41:26 kern.warn kernel: [  311.715197] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
Jun 12 22:41:26 kern.warn kernel: [  311.811185] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
Jun 12 22:41:40 daemon.notice hostapd: phy1-ap0: Prune association for 38:f9:d3:19:85:f8
Jun 12 22:41:40 daemon.notice hostapd: phy1-ap0: AP-STA-DISCONNECTED 38:f9:d3:19:85:f8
Jun 12 22:41:40 daemon.notice hostapd: phy0-ap0: AP-STA-CONNECTED 38:f9:d3:19:85:f8 auth_alg=open
Jun 12 22:41:40 daemon.notice hostapd: phy0-ap0: EAPOL-4WAY-HS-COMPLETED 38:f9:d3:19:85:f8
Jun 12 22:42:28 daemon.notice hostapd: phy1-ap0: AP-STA-CONNECTED f2:7f:ba:ea:42:9c auth_alg=sae
Jun 12 22:42:28 daemon.notice hostapd: phy1-ap0: EAPOL-4WAY-HS-COMPLETED f2:7f:ba:ea:42:9c
Jun 12 22:42:28 daemon.notice hostapd: phy1-ap0: AP-STA-DISCONNECTED f2:7f:ba:ea:42:9c
Jun 12 22:43:54 daemon.notice hostapd: phy1-ap0: Prune association for 58:24:29:e1:c2:bb
Jun 12 22:43:54 daemon.notice hostapd: phy1-ap0: AP-STA-DISCONNECTED 58:24:29:e1:c2:bb
Jun 12 22:43:54 daemon.notice hostapd: phy0-ap0: AP-STA-CONNECTED 58:24:29:e1:c2:bb auth_alg=sae
Jun 12 22:43:54 daemon.notice hostapd: phy0-ap0: EAPOL-4WAY-HS-COMPLETED 58:24:29:e1:c2:bb
Jun 12 22:43:59 daemon.notice hostapd: phy0-ap0: Prune association for 58:24:29:e1:c2:bb
Jun 12 22:43:59 daemon.notice hostapd: phy0-ap0: AP-STA-DISCONNECTED 58:24:29:e1:c2:bb
Jun 12 22:43:59 daemon.notice hostapd: phy1-ap0: AP-STA-CONNECTED 58:24:29:e1:c2:bb auth_alg=open
Jun 12 22:43:59 daemon.notice hostapd: phy1-ap0: EAPOL-4WAY-HS-COMPLETED 58:24:29:e1:c2:bb

Change to non-ct driver and firmware

This topic was automatically closed 10 days after the last reply. New replies are no longer allowed.