Hi Daniel, tried to install the kmod you mentioned, I have an incompatible kernel version for the opkg package apparently, and I cant modprobe it. I have tried multiple times to reflash your 0.5.3 release and even downgrade to 0.5.2 using the instructions flash ie force-flash xxx-ubi-initramfs-recovery-installer.itb for that version, followed by flashing the xxx-ubi-initramfs-squashfs-sysupgrade.itb for that version. Both via the Luci interface and cli with -F -n flags. It always comes back after reboot with the currently flashed version which is my snapshot upgrade on top of virgin stock fw->0.5.3 ---SNAPSHOT r17443-90e167abaa. Every flash seems to come back to the current build with erased config (-n switch). I'm wondering if this symptom means that the flashing is unsuccessful and it reverts back or to the second fw? I dont have a serial cable hooked up to see the full output of CLI sysupgrade, but the first few lines look successful before dropbear/ssh die and my console session ends.
@base0010 are you sure you have used the right file and have downloaded the binary from github or built yourself?
There is no point in downgrading the installer to v0.5.2, though it also doesn't hurt or change anything of v0.5.3 has already been installed before (because v0.5.3 applies a 1-time fix for the factory ECC data, downgrading won't revert that).
If a flashed firmware doesn't come up (but rather the recovery firmware comes up instead) this is usually because the flashed file has been corrupted. Please make sure all the files you are using are the correct size and hash.
If the system keeps booting into recovery a cause can also be that there has previously been a kernel crash and crashlogs have not been cleared yet. Check if you see any files in /sys/fs/pstore/ and if so, take a look at them (maybe post them here) and delete them as the flashed firmware will only be loaded if pstore is empty.
4 Likes
To whom it may concern, I've updated the upgrade server to use more differentiated caching should resolve any further checksum issues with auc. Thanks for reporting the issues earlier!
5 Likes
Can you open an issue on MT76 repo?
Do I need to open a bug report for MT76 for the snapshot releases? Sorry I haven't done that before, can you tell me where I need to open the issue.
I have been running the RT3200 (UBI install, snapshot on 8/31/2021, r17457) for a few days now without any issues, but I woke up to recovery mode this morning -- it looks related to the similar oops linked previously by a few users (0000000000000053). These were the two files in the /sys/fs/pstore folder:
Oops#1 Part1
<6>[ 5370.776151] br-lan: port 5(wlan0) entered blocking state
<6>[ 5370.781555] br-lan: port 5(wlan0) entered forwarding state
<6>[ 5371.366785] br-lan: port 5(wlan0) entered disabled state
<6>[ 5372.130752] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
<6>[ 5372.137289] br-lan: port 5(wlan0) entered blocking state
<6>[ 5372.142602] br-lan: port 5(wlan0) entered forwarding state
<6>[118488.919642] device wlan0 left promiscuous mode
<6>[118488.924348] br-lan: port 5(wlan0) entered disabled state
<6>[118488.954141] device wlan1 left promiscuous mode
<6>[118488.958808] br-lan: port 6(wlan1) entered disabled state
<6>[118489.542443] br-lan: port 5(wlan0) entered blocking state
<6>[118489.547927] br-lan: port 5(wlan0) entered disabled state
<6>[118489.553594] device wlan0 entered promiscuous mode
<6>[118489.558536] br-lan: port 5(wlan0) entered blocking state
<6>[118489.563995] br-lan: port 5(wlan0) entered forwarding state
<6>[118489.766174] br-lan: port 6(wlan1) entered blocking state
<6>[118489.771715] br-lan: port 6(wlan1) entered disabled state
<6>[118489.777489] device wlan1 entered promiscuous mode
<6>[118489.782431] br-lan: port 6(wlan1) entered blocking state
<6>[118489.787930] br-lan: port 6(wlan1) entered forwarding state
<6>[118490.235668] br-lan: port 5(wlan0) entered disabled state
<6>[118490.253180] br-lan: port 6(wlan1) entered disabled state
<6>[118490.540228] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
<6>[118490.546863] br-lan: port 6(wlan1) entered blocking state
<6>[118490.552273] br-lan: port 6(wlan1) entered forwarding state
<6>[118490.944491] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
<6>[118490.951075] br-lan: port 5(wlan0) entered blocking state
<6>[118490.956562] br-lan: port 5(wlan0) entered forwarding state
<6>[119774.042645] mt7530 mdio-bus:00 lan1: Link is Down
<6>[119774.047630] br-lan: port 1(lan1) entered disabled state
<6>[119781.324603] mt7530 mdio-bus:00 lan1: Link is Up - 1Gbps/Full - flow control rx/tx
<6>[119781.332232] br-lan: port 1(lan1) entered blocking state
<6>[119781.337547] br-lan: port 1(lan1) entered forwarding state
<4>[120205.955517] ------------[ cut here ]------------
<6>[120205.960228] NETDEV WATCHDOG: eth0 (mtk_soc_eth): transmit queue 0 timed out
<4>[120205.967311] WARNING: CPU: 0 PID: 0 at dev_watchdog+0x2a8/0x2b0
<7>[120205.973221] Modules linked in: pppoe ppp_async iptable_nat xt_state xt_nat xt_conntrack xt_REDIRECT xt_MASQUERADE xt_FLOWOFFLOAD xt_CT pppox ppp_generic nf_nat nf_flow_table nf_conntrack_netlink nf_conntrack mt7915e mt7615e mt7615_common mt76_connac_lib mt76 mac80211 ipt_REJECT cfg80211 xt_time xt_tcpudp xt_multiport xt_mark xt_mac xt_limit xt_comment xt_TCPMSS xt_LOG slhc nfnetlink nf_reject_ipv4 nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 iptable_mangle iptable_filter ip_tables hwmon crc_ccitt compat nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 vfat fat autofs4 nls_utf8 nls_iso8859_1 nls_cp437 seqiv uas usb_storage leds_gpio xhci_plat_hcd gpio_button_hotplug
<7>[120206.036900] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G S 5.10.61 #0
<7>[120206.044370] Hardware name: Linksys E8450 (UBI) (DT)
<7>[120206.049326] pstate: 40000005 (nZcv daif -PAN -UAO -TCO BTYPE=--)
<7>[120206.055410] pc : dev_watchdog+0x2a8/0x2b0
<7>[120206.059497] lr : dev_watchdog+0x2a8/0x2b0
<7>[120206.063584] sp : ffffffc010bcbd80
<7>[120206.066975] x29: ffffffc010bcbd80 x28: ffffffc010a7d580
<7>[120206.072366] x27: 0000000000000140 x26: 00000000ffffffff
<7>[120206.077756] x25: 0000000000000000 x24: 0000000000000000
<7>[120206.083147] x23: ffffff8000c55480 x22: 0000000000000001
<7>[120206.088538] x21: ffffffc010a96000 x20: ffffff8000c55000
<7>[120206.093928] x19: 0000000000000000 x18: 000000000000018f
<7>[120206.099318] x17: 0000000000000000 x16: 0000000000000000
<7>[120206.104709] x15: ffffffc010aa6a60 x14: 00000000000004ad
<7>[120206.110100] x13: 000000000000018f x12: ffffffc010bcba58
<7>[120206.115491] x11: ffffffc010afea60 x10: 00000000fffff000
<7>[120206.120881] x9 : ffffffc010afea60 x8 : 0000000000000000
<7>[120206.126272] x7 : 80000000fffff000 x6 : 0000000000000001
<7>[120206.131662] x5 : 0000000000000000 x4 : 0000000000000000
<7>[120206.137052] x3 : 0000000000000000 x2 : ffffff801febb028
<7>[120206.142443] x1 : ffffffc00f437000 x0 : 000000000000003f
<7>[120206.147833] Call trace:
<7>[120206.150358] dev_watchdog+0x2a8/0x2b0
<7>[120206.154101] call_timer_fn.constprop.0+0x20/0x80
<7>[120206.158796] expire_timers+0xa8/0x110
<7>[120206.162536] run_timer_softirq+0x110/0x290
<7>[120206.166710] _stext+0x124/0x28c
<7>[120206.169931] irq_exit+0xd8/0xf4
<7>[120206.173151] __handle_domain_irq+0x7c/0xdc
<7>[120206.177327] gic_handle_irq+0x68/0x8c
<7>[120206.181066] el1_irq+0xc8/0x180
<7>[120206.184287] arch_cpu_idle+0x14/0x2c
<7>[120206.187941] do_idle+0xc4/0x140
<7>[120206.191159] cpu_startup_entry+0x24/0x50
<7>[120206.195160] rest_init+0xb8/0xc4
<7>[120206.198467] arch_call_rest_init+0xc/0x14
<7>[120206.202554] start_kernel+0x470/0x488
<4>[120206.206294] ---[ end trace 6f84a83193b17c4a ]---
<3>[120206.211036] mtk_soc_eth 1b100000.ethernet eth0: transmit timed out
<6>[120206.220347] mtk_soc_eth 1b100000.ethernet eth0: Link is Down
<6>[120206.251108] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
<6>[120206.259598] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
<3>[120218.195395] mtk_soc_eth 1b100000.ethernet eth0: transmit timed out
<6>[120218.201789] mtk_soc_eth 1b100000.ethernet eth0: Link is Down
<6>[120218.231465] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
<6>[120218.239939] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
<1>[283993.888652] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000053
<1>[283993.897523] Mem abort info:
<1>[283993.900423] ESR = 0x96000005
<1>[283993.903555] EC = 0x25: DABT (current EL), IL = 32 bits
<1>[283993.908997] SET = 0, FnV = 0
<1>[283993.912166] EA = 0, S1PTW = 0
<1>[283993.915382] Data abort info:
<1>[283993.918390] ISV = 0, ISS = 0x00000005
<1>[283993.922341] CM = 0, WnR = 0
<1>[283993.925388] user pgtable: 4k pages, 39-bit VAs, pgdp=00000000428db000
<1>[283993.931911] [0000000000000053] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000
<0>[283993.940786] Internal error: Oops: 96000005 [#1] SMP
<7>[283993.945741] Modules linked in: pppoe ppp_async iptable_nat xt_state xt_nat xt_conntrack xt_REDIRECT xt_MASQUERADE xt_FLOWOFFLOAD xt_CT pppox ppp_generic nf_nat nf_flow_table nf_conntrack_netlink nf_conntrack mt7915e mt7615e mt7615_common mt76_connac_lib mt76 mac80211 ipt_REJECT cfg80211 xt_time xt_tcpudp xt_multiport xt_mark xt_mac xt_limit xt_comment xt_TCPMSS xt_LOG slhc nfnetlink nf_reject_ipv4 nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 iptable_mangle iptable_filter ip_tables hwmon crc_ccitt compat nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 vfat fat autofs4 nls_utf8 nls_iso8859_1 nls_cp437 seqiv uas usb_storage leds_gpio xhci_plat_hcd gpio_button_hotplug
<7>[283994.009413] CPU: 0 PID: 1155 Comm: napi/phy1-9 Tainted: G S W 5.10.61 #0
<7>[283994.017318] Hardware name: Linksys E8450 (UBI) (DT)
<7>[283994.022274] pstate: 60000005 (nZCv daif -PAN -UAO -TCO BTYPE=--)
<7>[283994.028366] pc : mt76_tx_status_skb_done+0x0/0x80 [mt76]
<7>[283994.033759] lr : mt7915_queue_rx_skb+0xa04/0x154c [mt7915e]
<7>[283994.039407] sp : ffffffc010e9bc20
<7>[283994.042798] x29: ffffffc010e9bc20 x28: ffffff800222de00
<7>[283994.048188] x27: 0000000040000000 x26: ffffff800222b8d0
<7>[283994.053579] x25: ffffff800222dec0 x24: ffffff8002068828
<7>[283994.058969] x23: 0000000000000000 x22: 000000000000000b
<7>[283994.064360] x21: ffffff8002717bb8 x20: ffffff8002068828
<7>[283994.069750] x19: ffffff800222a800 x18: ffffff80019543b0
<7>[283994.075141] x17: 00000000ffffffff x16: 0000000000000000
<7>[283994.080531] x15: 0000000000000004 x14: ffffff800222c918
<7>[283994.085922] x13: 0000000000000000 x12: ffffff8001fc0c48
<7>[283994.091313] x11: ffffff800222c800 x10: ffffffc010a96000
<7>[283994.096704] x9 : 0000000000000064 x8 : ffffff800222a800
<7>[283994.102094] x7 : ffffff800222c950 x6 : 0000000101b0e2f2
<7>[283994.107485] x5 : fffffffefe4f1d5c x4 : ffffff8003c48200
<7>[283994.112875] x3 : ffffffc010e9bd18 x2 : ffffffc010e9bd18
<7>[283994.118266] x1 : 0000000000000000 x0 : ffffff800222a800
<7>[283994.123657] Call trace:
<7>[283994.126185] mt76_tx_status_skb_done+0x0/0x80 [mt76]
<7>[283994.131229] mt76_dma_rx_poll+0x284/0xb70 [mt76]
<7>[283994.135928] __napi_poll+0x34/0x140
<7>[283994.139495] napi_threaded_poll+0x84/0xf0
<7>[283994.143585] kthread+0x120/0x124
<7>[283994.146891] ret_from_fork+0x10/0x18
<0>[283994.150548] Code: 54fffa41 d2800000 d65f03c0 d503201f (39414c24)
<4>[283994.156718] ---[ end trace 6f84a83193b17c4b ]---
Panic#2 Part1
<6>[ 5372.137289] br-lan: port 5(wlan0) entered blocking state
<6>[ 5372.142602] br-lan: port 5(wlan0) entered forwarding state
<6>[118488.919642] device wlan0 left promiscuous mode
<6>[118488.924348] br-lan: port 5(wlan0) entered disabled state
<6>[118488.954141] device wlan1 left promiscuous mode
<6>[118488.958808] br-lan: port 6(wlan1) entered disabled state
<6>[118489.542443] br-lan: port 5(wlan0) entered blocking state
<6>[118489.547927] br-lan: port 5(wlan0) entered disabled state
<6>[118489.553594] device wlan0 entered promiscuous mode
<6>[118489.558536] br-lan: port 5(wlan0) entered blocking state
<6>[118489.563995] br-lan: port 5(wlan0) entered forwarding state
<6>[118489.766174] br-lan: port 6(wlan1) entered blocking state
<6>[118489.771715] br-lan: port 6(wlan1) entered disabled state
<6>[118489.777489] device wlan1 entered promiscuous mode
<6>[118489.782431] br-lan: port 6(wlan1) entered blocking state
<6>[118489.787930] br-lan: port 6(wlan1) entered forwarding state
<6>[118490.235668] br-lan: port 5(wlan0) entered disabled state
<6>[118490.253180] br-lan: port 6(wlan1) entered disabled state
<6>[118490.540228] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
<6>[118490.546863] br-lan: port 6(wlan1) entered blocking state
<6>[118490.552273] br-lan: port 6(wlan1) entered forwarding state
<6>[118490.944491] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
<6>[118490.951075] br-lan: port 5(wlan0) entered blocking state
<6>[118490.956562] br-lan: port 5(wlan0) entered forwarding state
<6>[119774.042645] mt7530 mdio-bus:00 lan1: Link is Down
<6>[119774.047630] br-lan: port 1(lan1) entered disabled state
<6>[119781.324603] mt7530 mdio-bus:00 lan1: Link is Up - 1Gbps/Full - flow control rx/tx
<6>[119781.332232] br-lan: port 1(lan1) entered blocking state
<6>[119781.337547] br-lan: port 1(lan1) entered forwarding state
<4>[120205.955517] ------------[ cut here ]------------
<6>[120205.960228] NETDEV WATCHDOG: eth0 (mtk_soc_eth): transmit queue 0 timed out
<4>[120205.967311] WARNING: CPU: 0 PID: 0 at dev_watchdog+0x2a8/0x2b0
<7>[120205.973221] Modules linked in: pppoe ppp_async iptable_nat xt_state xt_nat xt_conntrack xt_REDIRECT xt_MASQUERADE xt_FLOWOFFLOAD xt_CT pppox ppp_generic nf_nat nf_flow_table nf_conntrack_netlink nf_conntrack mt7915e mt7615e mt7615_common mt76_connac_lib mt76 mac80211 ipt_REJECT cfg80211 xt_time xt_tcpudp xt_multiport xt_mark xt_mac xt_limit xt_comment xt_TCPMSS xt_LOG slhc nfnetlink nf_reject_ipv4 nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 iptable_mangle iptable_filter ip_tables hwmon crc_ccitt compat nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 vfat fat autofs4 nls_utf8 nls_iso8859_1 nls_cp437 seqiv uas usb_storage leds_gpio xhci_plat_hcd gpio_button_hotplug
<7>[120206.036900] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G S 5.10.61 #0
<7>[120206.044370] Hardware name: Linksys E8450 (UBI) (DT)
<7>[120206.049326] pstate: 40000005 (nZcv daif -PAN -UAO -TCO BTYPE=--)
<7>[120206.055410] pc : dev_watchdog+0x2a8/0x2b0
<7>[120206.059497] lr : dev_watchdog+0x2a8/0x2b0
<7>[120206.063584] sp : ffffffc010bcbd80
<7>[120206.066975] x29: ffffffc010bcbd80 x28: ffffffc010a7d580
<7>[120206.072366] x27: 0000000000000140 x26: 00000000ffffffff
<7>[120206.077756] x25: 0000000000000000 x24: 0000000000000000
<7>[120206.083147] x23: ffffff8000c55480 x22: 0000000000000001
<7>[120206.088538] x21: ffffffc010a96000 x20: ffffff8000c55000
<7>[120206.093928] x19: 0000000000000000 x18: 000000000000018f
<7>[120206.099318] x17: 0000000000000000 x16: 0000000000000000
<7>[120206.104709] x15: ffffffc010aa6a60 x14: 00000000000004ad
<7>[120206.110100] x13: 000000000000018f x12: ffffffc010bcba58
<7>[120206.115491] x11: ffffffc010afea60 x10: 00000000fffff000
<7>[120206.120881] x9 : ffffffc010afea60 x8 : 0000000000000000
<7>[120206.126272] x7 : 80000000fffff000 x6 : 0000000000000001
<7>[120206.131662] x5 : 0000000000000000 x4 : 0000000000000000
<7>[120206.137052] x3 : 0000000000000000 x2 : ffffff801febb028
<7>[120206.142443] x1 : ffffffc00f437000 x0 : 000000000000003f
<7>[120206.147833] Call trace:
<7>[120206.150358] dev_watchdog+0x2a8/0x2b0
<7>[120206.154101] call_timer_fn.constprop.0+0x20/0x80
<7>[120206.158796] expire_timers+0xa8/0x110
<7>[120206.162536] run_timer_softirq+0x110/0x290
<7>[120206.166710] _stext+0x124/0x28c
<7>[120206.169931] irq_exit+0xd8/0xf4
<7>[120206.173151] __handle_domain_irq+0x7c/0xdc
<7>[120206.177327] gic_handle_irq+0x68/0x8c
<7>[120206.181066] el1_irq+0xc8/0x180
<7>[120206.184287] arch_cpu_idle+0x14/0x2c
<7>[120206.187941] do_idle+0xc4/0x140
<7>[120206.191159] cpu_startup_entry+0x24/0x50
<7>[120206.195160] rest_init+0xb8/0xc4
<7>[120206.198467] arch_call_rest_init+0xc/0x14
<7>[120206.202554] start_kernel+0x470/0x488
<4>[120206.206294] ---[ end trace 6f84a83193b17c4a ]---
<3>[120206.211036] mtk_soc_eth 1b100000.ethernet eth0: transmit timed out
<6>[120206.220347] mtk_soc_eth 1b100000.ethernet eth0: Link is Down
<6>[120206.251108] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
<6>[120206.259598] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
<3>[120218.195395] mtk_soc_eth 1b100000.ethernet eth0: transmit timed out
<6>[120218.201789] mtk_soc_eth 1b100000.ethernet eth0: Link is Down
<6>[120218.231465] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
<6>[120218.239939] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
<1>[283993.888652] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000053
<1>[283993.897523] Mem abort info:
<1>[283993.900423] ESR = 0x96000005
<1>[283993.903555] EC = 0x25: DABT (current EL), IL = 32 bits
<1>[283993.908997] SET = 0, FnV = 0
<1>[283993.912166] EA = 0, S1PTW = 0
<1>[283993.915382] Data abort info:
<1>[283993.918390] ISV = 0, ISS = 0x00000005
<1>[283993.922341] CM = 0, WnR = 0
<1>[283993.925388] user pgtable: 4k pages, 39-bit VAs, pgdp=00000000428db000
<1>[283993.931911] [0000000000000053] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000
<0>[283993.940786] Internal error: Oops: 96000005 [#1] SMP
<7>[283993.945741] Modules linked in: pppoe ppp_async iptable_nat xt_state xt_nat xt_conntrack xt_REDIRECT xt_MASQUERADE xt_FLOWOFFLOAD xt_CT pppox ppp_generic nf_nat nf_flow_table nf_conntrack_netlink nf_conntrack mt7915e mt7615e mt7615_common mt76_connac_lib mt76 mac80211 ipt_REJECT cfg80211 xt_time xt_tcpudp xt_multiport xt_mark xt_mac xt_limit xt_comment xt_TCPMSS xt_LOG slhc nfnetlink nf_reject_ipv4 nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 iptable_mangle iptable_filter ip_tables hwmon crc_ccitt compat nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 vfat fat autofs4 nls_utf8 nls_iso8859_1 nls_cp437 seqiv uas usb_storage leds_gpio xhci_plat_hcd gpio_button_hotplug
<7>[283994.009413] CPU: 0 PID: 1155 Comm: napi/phy1-9 Tainted: G S W 5.10.61 #0
<7>[283994.017318] Hardware name: Linksys E8450 (UBI) (DT)
<7>[283994.022274] pstate: 60000005 (nZCv daif -PAN -UAO -TCO BTYPE=--)
<7>[283994.028366] pc : mt76_tx_status_skb_done+0x0/0x80 [mt76]
<7>[283994.033759] lr : mt7915_queue_rx_skb+0xa04/0x154c [mt7915e]
<7>[283994.039407] sp : ffffffc010e9bc20
<7>[283994.042798] x29: ffffffc010e9bc20 x28: ffffff800222de00
<7>[283994.048188] x27: 0000000040000000 x26: ffffff800222b8d0
<7>[283994.053579] x25: ffffff800222dec0 x24: ffffff8002068828
<7>[283994.058969] x23: 0000000000000000 x22: 000000000000000b
<7>[283994.064360] x21: ffffff8002717bb8 x20: ffffff8002068828
<7>[283994.069750] x19: ffffff800222a800 x18: ffffff80019543b0
<7>[283994.075141] x17: 00000000ffffffff x16: 0000000000000000
<7>[283994.080531] x15: 0000000000000004 x14: ffffff800222c918
<7>[283994.085922] x13: 0000000000000000 x12: ffffff8001fc0c48
<7>[283994.091313] x11: ffffff800222c800 x10: ffffffc010a96000
<7>[283994.096704] x9 : 0000000000000064 x8 : ffffff800222a800
<7>[283994.102094] x7 : ffffff800222c950 x6 : 0000000101b0e2f2
<7>[283994.107485] x5 : fffffffefe4f1d5c x4 : ffffff8003c48200
<7>[283994.112875] x3 : ffffffc010e9bd18 x2 : ffffffc010e9bd18
<7>[283994.118266] x1 : 0000000000000000 x0 : ffffff800222a800
<7>[283994.123657] Call trace:
<7>[283994.126185] mt76_tx_status_skb_done+0x0/0x80 [mt76]
<7>[283994.131229] mt76_dma_rx_poll+0x284/0xb70 [mt76]
<7>[283994.135928] __napi_poll+0x34/0x140
<7>[283994.139495] napi_threaded_poll+0x84/0xf0
<7>[283994.143585] kthread+0x120/0x124
<7>[283994.146891] ret_from_fork+0x10/0x18
<0>[283994.150548] Code: 54fffa41 d2800000 d65f03c0 d503201f (39414c24)
<4>[283994.156718] ---[ end trace 6f84a83193b17c4b ]---
<0>[283994.169736] Kernel panic - not syncing: Oops: Fatal exception in interrupt
<2>[283994.176692] SMP: stopping secondary CPUs
<0>[283994.180697] Kernel Offset: disabled
<0>[283994.184264] CPU features: 0x0000002,04002004
<0>[283994.188610] Memory Limit: none
Related Posts:
#346
#265
#244
I will dump my pstore logs in the github issue as well:
4 Likes
helllo @waxhell and welcome do you have installed before the correclty recovery installer of dangowrt ?
not 0.5.2 but well 0.5.3 ? thanks
1 Like
I am running the 0.5.3 version of the recovery installer.
1 Like
Likely that has no relation to the WiFi driver crash, which has surfaced much earlier than the new flash driver.
Ps.
Nice debugging in that GitHub issue ticket that you linked. Sounds like the culprit is found, but no patch had yet been made/merged.
1 Like
Failed to boot the firmware if it is using non-ubi version....
openwrt-mediatek-mt7622-linksys_e8450-squashfs-sysupgrade.bin
================================================
bootargs=console=ttyS0,115200 rootdelay=1 rootfstype=squashfs earlyprintk mtdparts=slave
================================================
[ 2.344458] UBI error: no valid UBI magic found inside mtd10
[ 2.350811] Waiting 1 sec before mounting root device...
[ 3.431045] /dev/root: Can't open blockdev
[ 3.435134] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[ 3.442618] Please append a correct "root=" boot option; here are the available partitions:
[ 3.450976] 1f00 512 mtdblock0
[ 3.450978] (driver?)
[ 3.457500] 1f02 256 mtdblock1
[ 3.457502] (driver?)
[ 3.464029] 1f04 512 mtdblock2
[ 3.464031] (driver?)
[ 3.470554] 1f06 512 mtdblock3
[ 3.470556] (driver?)
[ 3.477083] 1f08 1024 mtdblock4
[ 3.477085] (driver?)
[ 3.483611] 1f0a 128 mtdblock5
[ 3.483613] (driver?)
[ 3.490136] 1f0c 128 mtdblock6
[ 3.490137] (driver?)
[ 3.496668] 1f0e 128 mtdblock7
[ 3.496669] (driver?)
[ 3.503196] 1f10 30720 mtdblock8
[ 3.503197] (driver?)
[ 3.509721] 1f12 30720 mtdblock9
[ 3.509722] (driver?)
[ 3.516250] 1f14 25600 mtdblock10
[ 3.516252] (driver?)
[ 3.522865] 1f16 20480 mtdblock11
[ 3.522867] (driver?)
[ 3.529476] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 3.537731] SMP: stopping secondary CPUs
[ 3.541646] Kernel Offset: disabled
[ 3.545125] CPU features: 0x0000002,04002004
[ 3.549385] Memory Limit: none
[ 3.557161] Rebooting in 1 seconds..
4 Likes
r17469-9e9057f416 seems stable on my RT3200. Using 2.4Ghz (40Mhz) + 5Ghz (80Mhz) and WireGuard. All works fine. Wi-Fi coverage seems comparable to Asus RT-AX86u.
I am really struggling with something. What is the easiest way to add 'rclone' having flashed the latest snapshot? Could the 'rclone' package possibly be added to future snapshots please? Very useful package! Any help much appreciated.
1 Like
So I have a set of pstore logs now. The router again crashed overnight, and I have the following logs. Am I right in thinking I should turn off hardware flow offloading?
> BusyBox v1.33.1 (2021-09-01 13:40:27 UTC) built-in shell (ash)
>
> _______ ________ __
> | |.-----.-----.-----.| | | |.----.| |_
> | - || _ | -__| || | | || _|| _|
> |_______|| __|_____|__|__||________||__| |____|
> |__| W I R E L E S S F R E E D O M
> -----------------------------------------------------
> OpenWrt SNAPSHOT, r17469-9e9057f416
> -----------------------------------------------------
> === WARNING! =====================================
> There is no root password defined on this device!
> Use the "passwd" command to set up a new password
> in order to prevent unauthorized SSH logins.
> --------------------------------------------------
> root@OpenWrt:~# ls -1 /sys/fs/pstore
> dmesg-ramoops-0
> dmesg-ramoops-1
> root@OpenWrt:~# cat /sys/fs/pstore/*
> Oops#1 Part1
> <14>[ 7.490785] block: extroot: not configured
> <14>[ 7.495845] mount_root: switching to ubifs overlay
> <6>[ 7.503692] overlayfs: "xino" feature enabled using 2 upper inode bits.
> <15>[ 7.512829] urandom-seed: Seeding with /etc/urandom.seed
> <14>[ 7.563695] procd: - early -
> <14>[ 7.566661] procd: - watchdog -
> <14>[ 8.109276] procd: - watchdog -
> <14>[ 8.115024] procd: - ubus -
> <5>[ 8.146006] random: ubusd: uninitialized urandom read (4 bytes read)
> <5>[ 8.167503] random: ubusd: uninitialized urandom read (4 bytes read)
> <5>[ 8.175735] random: ubusd: uninitialized urandom read (4 bytes read)
> <14>[ 8.183278] procd: - init -
> <14>[ 8.459595] urngd: v1.0.2 started.
> <5>[ 8.488777] random: crng init done
> <5>[ 8.492201] random: 6 urandom warning(s) missed due to ratelimiting
> <14>[ 8.557709] kmodloader: loading kernel modules from /etc/modules.d/*
> <6>[ 8.594347] Loading modules backported from Linux version v5.10.42-0-g65859eca4dff
> <6>[ 8.601968] Backport generated by backports.git v5.10.42-1-0-gbee5c545
> <6>[ 8.627939] xt_time: kernel timezone is -0000
> <7>[ 8.691732] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
> <7>[ 8.702140] mt7915e 0000:01:00.0: assign IRQ: got 143
> <7>[ 8.707294] pci 0000:00:00.0: enabling bus mastering
> <6>[ 8.712276] mt7915e 0000:01:00.0: enabling device (0000 -> 0002)
> <7>[ 8.718388] mt7915e 0000:01:00.0: enabling bus mastering
> <6>[ 8.741484] mt7622-wmac 18000000.wmac: HW/SW Version: 0x8a108a10, Build Time: 20190801210006a
> <6>[ 8.741484]
> <6>[ 8.789984] mt7915e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20201105222230a
> <6>[ 8.789984]
> <6>[ 8.825538] mt7622-wmac 18000000.wmac: N9 Firmware Version: 2.0, Build Time: 20200131180931
> <6>[ 8.921497] mt7915e 0000:01:00.0: WM Firmware Version: ____000000, Build Time: 20201105222304
> <6>[ 8.944274] mt7915e 0000:01:00.0: WA Firmware Version: DEV_000000, Build Time: 20201105222323
> <6>[ 9.068630] PPP generic driver version 2.4.2
> <6>[ 9.073956] NET: Registered protocol family 24
> <14>[ 9.085015] kmodloader: done loading kernel modules from /etc/modules.d/*
> <6>[ 11.584030] mtk_soc_eth 1b100000.ethernet eth0: Link is Down
> <6>[ 11.593842] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
> <6>[ 11.602348] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
> <6>[ 11.611057] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> <6>[ 11.626000] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode
> <6>[ 11.637733] 8021q: adding VLAN 0 to HW filter on device lan1
> <6>[ 11.645848] br-lan: port 1(lan1) entered blocking state
> <6>[ 11.651112] br-lan: port 1(lan1) entered disabled state
> <6>[ 11.666598] device lan1 entered promiscuous mode
> <6>[ 11.671221] device eth0 entered promiscuous mode
> <6>[ 11.693539] mt7530 mdio-bus:00 lan2: configuring for phy/gmii link mode
> <6>[ 11.720320] 8021q: adding VLAN 0 to HW filter on device lan2
> <6>[ 11.738764] mt7530 mdio-bus:00 lan2: Link is Up - 100Mbps/Full - flow control rx/tx
> <6>[ 11.748896] br-lan: port 2(lan2) entered blocking state
> <6>[ 11.754128] br-lan: port 2(lan2) entered disabled state
> <6>[ 11.768569] device lan2 entered promiscuous mode
> <6>[ 11.789403] br-lan: port 2(lan2) entered blocking state
> <6>[ 11.794675] br-lan: port 2(lan2) entered forwarding state
> <6>[ 11.803837] mt7530 mdio-bus:00 lan3: configuring for phy/gmii link mode
> <6>[ 11.816766] 8021q: adding VLAN 0 to HW filter on device lan3
> <6>[ 11.824724] br-lan: port 3(lan3) entered blocking state
> <6>[ 11.830069] br-lan: port 3(lan3) entered disabled state
> <6>[ 11.840021] mt7530 mdio-bus:00 lan3: Link is Up - 1Gbps/Full - flow control rx/tx
> <6>[ 11.849200] device lan3 entered promiscuous mode
> <6>[ 11.860204] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
> <6>[ 11.870429] br-lan: port 3(lan3) entered blocking state
> <6>[ 11.875722] br-lan: port 3(lan3) entered forwarding state
> <6>[ 11.887849] mt7530 mdio-bus:00 lan4: configuring for phy/gmii link mode
> <6>[ 11.901091] 8021q: adding VLAN 0 to HW filter on device lan4
> <6>[ 11.916762] br-lan: port 4(lan4) entered blocking state
> <6>[ 11.922023] br-lan: port 4(lan4) entered disabled state
> <6>[ 11.929651] device lan4 entered promiscuous mode
> <6>[ 11.949530] mt7530 mdio-bus:00 wan: configuring for phy/gmii link mode
> <6>[ 11.960662] 8021q: adding VLAN 0 to HW filter on device wan
> <6>[ 11.966863] mt7530 mdio-bus:00 wan: Link is Up - 1Gbps/Full - flow control off
> <6>[ 11.974344] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready
> <6>[ 12.808204] br-lan: port 5(wlan0) entered blocking state
> <6>[ 12.813540] br-lan: port 5(wlan0) entered disabled state
> <6>[ 12.819127] device wlan0 entered promiscuous mode
> <6>[ 12.823932] br-lan: port 5(wlan0) entered blocking state
> <6>[ 12.829316] br-lan: port 5(wlan0) entered forwarding state
> <6>[ 12.835654] br-lan: port 5(wlan0) entered disabled state
> <6>[ 14.821089] br-lan: port 6(wlan1) entered blocking state
> <6>[ 14.826459] br-lan: port 6(wlan1) entered disabled state
> <6>[ 14.832008] device wlan1 entered promiscuous mode
> <6>[ 14.836895] br-lan: port 6(wlan1) entered blocking state
> <6>[ 14.842211] br-lan: port 6(wlan1) entered forwarding state
> <6>[ 14.848804] br-lan: port 6(wlan1) entered disabled state
> <6>[ 14.993569] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
> <6>[ 15.000083] br-lan: port 5(wlan0) entered blocking state
> <6>[ 15.005416] br-lan: port 5(wlan0) entered forwarding state
> <6>[ 80.697698] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
> <6>[ 80.704212] br-lan: port 6(wlan1) entered blocking state
> <6>[ 80.709531] br-lan: port 6(wlan1) entered forwarding state
> <1>[20022.809676] Unable to handle kernel paging request at virtual address dead000000000110
> <1>[20022.817603] Mem abort info:
> <1>[20022.820417] ESR = 0x96000004
> <1>[20022.823463] EC = 0x25: DABT (current EL), IL = 32 bits
> <1>[20022.828764] SET = 0, FnV = 0
> <1>[20022.831824] EA = 0, S1PTW = 0
> <1>[20022.834967] Data abort info:
> <1>[20022.837837] ISV = 0, ISS = 0x00000004
> <1>[20022.841718] CM = 0, WnR = 0
> <1>[20022.844679] [dead000000000110] address between user and kernel address ranges
> <0>[20022.851856] Internal error: Oops: 96000004 [#1] SMP
> <7>[20022.856756] Modules linked in: pppoe ppp_async iptable_nat xt_state xt_nat xt_conntrack xt_REDIRECT xt_MASQUERADE xt_FLOWOFFLOAD xt_CT pppox ppp_generic nf_nat nf_flow_table nf_conntrack mt7915e mt7615e mt7615_common mt76_connac_lib mt76 mac80211 ipt_REJECT cfg80211 xt_time xt_tcpudp xt_multiport xt_mark xt_mac xt_limit xt_comment xt_TCPMSS xt_LOG slhc nf_reject_ipv4 nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 iptable_mangle iptable_filter ip_tables hwmon crc_ccitt compat nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 vfat fat autofs4 nls_utf8 nls_iso8859_1 nls_cp437 seqiv uas usb_storage leds_gpio xhci_plat_hcd gpio_button_hotplug
> <7>[20022.917650] CPU: 0 PID: 4340 Comm: kworker/u4:4 Tainted: G S 5.10.61 #0
> <7>[20022.925556] Hardware name: Linksys E8450 (UBI) (DT)
> <7>[20022.930436] Workqueue: nf_ft_offload_stats nf_flow_table_offload_setup [nf_flow_table]
> <7>[20022.938346] pstate: 20000005 (nzCv daif -PAN -UAO -TCO BTYPE=--)
> <7>[20022.944345] pc : nf_flow_offload_ipv6_hook+0x6c8/0x1250 [nf_flow_table]
> <7>[20022.950950] lr : nf_flow_offload_ipv6_hook+0x6dc/0x1250 [nf_flow_table]
> <7>[20022.957554] sp : ffffffc014533c30
> <7>[20022.960858] x29: ffffffc014533c30 x28: 0000000000000000
> <7>[20022.966163] x27: ffffff8002b60ac8 x26: ffffffc010aa4520
> <7>[20022.971467] x25: 0000000000000003 x24: ffffffc014533d68
> <7>[20022.976771] x23: ffffffc008ad5648 x22: 0000000000000002
> <7>[20022.982076] x21: ffffffc008ad5638 x20: 0000000000000000
> <7>[20022.987379] x19: dead0000000000f0 x18: 0000000000000000
> <7>[20022.992683] x17: 0000000000000001 x16: 0000000000000003
> <7>[20022.997986] x15: 0000000000000000 x14: 0000000000000000
> <7>[20023.003290] x13: 0000000000000011 x12: ffffffffffffffff
> <7>[20023.008595] x11: 0000000000000040 x10: 0000000000000000
> <7>[20023.013899] x9 : 0000000000000001 x8 : 0000000000000000
> <7>[20023.019204] x7 : ffffffffffffffff x6 : 0000000000000000
> <7>[20023.024508] x5 : 0000000000000003 x4 : 0000000000000000
> <7>[20023.029812] x3 : ffffff8000ba8b00 x2 : 0000000000000000
> <7>[20023.035115] x1 : dead000000000100 x0 : 000000000000006d
> <7>[20023.040419] Call trace:
> <7>[20023.042859] nf_flow_offload_ipv6_hook+0x6c8/0x1250 [nf_flow_table]
> <7>[20023.049117] nf_flow_table_offload_setup+0x450/0x650 [nf_flow_table]
> <7>[20023.055464] process_one_work+0x1d4/0x370
> <7>[20023.059464] worker_thread+0x178/0x4e0
> <7>[20023.063204] kthread+0x120/0x124
> <7>[20023.066424] ret_from_fork+0x10/0x18
> <0>[20023.069994] Code: d1004013 eb0002bf 54000560 52800014 (f9401263)
> <4>[20023.076078] ---[ end trace 8a5e0377171e08b0 ]---
> Panic#2 Part1
> <14>[ 7.563695] procd: - early -
> <14>[ 7.566661] procd: - watchdog -
> <14>[ 8.109276] procd: - watchdog -
> <14>[ 8.115024] procd: - ubus -
> <5>[ 8.146006] random: ubusd: uninitialized urandom read (4 bytes read)
> <5>[ 8.167503] random: ubusd: uninitialized urandom read (4 bytes read)
> <5>[ 8.175735] random: ubusd: uninitialized urandom read (4 bytes read)
> <14>[ 8.183278] procd: - init -
> <14>[ 8.459595] urngd: v1.0.2 started.
> <5>[ 8.488777] random: crng init done
> <5>[ 8.492201] random: 6 urandom warning(s) missed due to ratelimiting
> <14>[ 8.557709] kmodloader: loading kernel modules from /etc/modules.d/*
> <6>[ 8.594347] Loading modules backported from Linux version v5.10.42-0-g65859eca4dff
> <6>[ 8.601968] Backport generated by backports.git v5.10.42-1-0-gbee5c545
> <6>[ 8.627939] xt_time: kernel timezone is -0000
> <7>[ 8.691732] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
> <7>[ 8.702140] mt7915e 0000:01:00.0: assign IRQ: got 143
> <7>[ 8.707294] pci 0000:00:00.0: enabling bus mastering
> <6>[ 8.712276] mt7915e 0000:01:00.0: enabling device (0000 -> 0002)
> <7>[ 8.718388] mt7915e 0000:01:00.0: enabling bus mastering
> <6>[ 8.741484] mt7622-wmac 18000000.wmac: HW/SW Version: 0x8a108a10, Build Time: 20190801210006a
> <6>[ 8.741484]
> <6>[ 8.789984] mt7915e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20201105222230a
> <6>[ 8.789984]
> <6>[ 8.825538] mt7622-wmac 18000000.wmac: N9 Firmware Version: 2.0, Build Time: 20200131180931
> <6>[ 8.921497] mt7915e 0000:01:00.0: WM Firmware Version: ____000000, Build Time: 20201105222304
> <6>[ 8.944274] mt7915e 0000:01:00.0: WA Firmware Version: DEV_000000, Build Time: 20201105222323
> <6>[ 9.068630] PPP generic driver version 2.4.2
> <6>[ 9.073956] NET: Registered protocol family 24
> <14>[ 9.085015] kmodloader: done loading kernel modules from /etc/modules.d/*
> <6>[ 11.584030] mtk_soc_eth 1b100000.ethernet eth0: Link is Down
> <6>[ 11.593842] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
> <6>[ 11.602348] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
> <6>[ 11.611057] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> <6>[ 11.626000] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode
> <6>[ 11.637733] 8021q: adding VLAN 0 to HW filter on device lan1
> <6>[ 11.645848] br-lan: port 1(lan1) entered blocking state
> <6>[ 11.651112] br-lan: port 1(lan1) entered disabled state
> <6>[ 11.666598] device lan1 entered promiscuous mode
> <6>[ 11.671221] device eth0 entered promiscuous mode
> <6>[ 11.693539] mt7530 mdio-bus:00 lan2: configuring for phy/gmii link mode
> <6>[ 11.720320] 8021q: adding VLAN 0 to HW filter on device lan2
> <6>[ 11.738764] mt7530 mdio-bus:00 lan2: Link is Up - 100Mbps/Full - flow control rx/tx
> <6>[ 11.748896] br-lan: port 2(lan2) entered blocking state
> <6>[ 11.754128] br-lan: port 2(lan2) entered disabled state
> <6>[ 11.768569] device lan2 entered promiscuous mode
> <6>[ 11.789403] br-lan: port 2(lan2) entered blocking state
> <6>[ 11.794675] br-lan: port 2(lan2) entered forwarding state
> <6>[ 11.803837] mt7530 mdio-bus:00 lan3: configuring for phy/gmii link mode
> <6>[ 11.816766] 8021q: adding VLAN 0 to HW filter on device lan3
> <6>[ 11.824724] br-lan: port 3(lan3) entered blocking state
> <6>[ 11.830069] br-lan: port 3(lan3) entered disabled state
> <6>[ 11.840021] mt7530 mdio-bus:00 lan3: Link is Up - 1Gbps/Full - flow control rx/tx
> <6>[ 11.849200] device lan3 entered promiscuous mode
> <6>[ 11.860204] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
> <6>[ 11.870429] br-lan: port 3(lan3) entered blocking state
> <6>[ 11.875722] br-lan: port 3(lan3) entered forwarding state
> <6>[ 11.887849] mt7530 mdio-bus:00 lan4: configuring for phy/gmii link mode
> <6>[ 11.901091] 8021q: adding VLAN 0 to HW filter on device lan4
> <6>[ 11.916762] br-lan: port 4(lan4) entered blocking state
> <6>[ 11.922023] br-lan: port 4(lan4) entered disabled state
> <6>[ 11.929651] device lan4 entered promiscuous mode
> <6>[ 11.949530] mt7530 mdio-bus:00 wan: configuring for phy/gmii link mode
> <6>[ 11.960662] 8021q: adding VLAN 0 to HW filter on device wan
> <6>[ 11.966863] mt7530 mdio-bus:00 wan: Link is Up - 1Gbps/Full - flow control off
> <6>[ 11.974344] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready
> <6>[ 12.808204] br-lan: port 5(wlan0) entered blocking state
> <6>[ 12.813540] br-lan: port 5(wlan0) entered disabled state
> <6>[ 12.819127] device wlan0 entered promiscuous mode
> <6>[ 12.823932] br-lan: port 5(wlan0) entered blocking state
> <6>[ 12.829316] br-lan: port 5(wlan0) entered forwarding state
> <6>[ 12.835654] br-lan: port 5(wlan0) entered disabled state
> <6>[ 14.821089] br-lan: port 6(wlan1) entered blocking state
> <6>[ 14.826459] br-lan: port 6(wlan1) entered disabled state
> <6>[ 14.832008] device wlan1 entered promiscuous mode
> <6>[ 14.836895] br-lan: port 6(wlan1) entered blocking state
> <6>[ 14.842211] br-lan: port 6(wlan1) entered forwarding state
> <6>[ 14.848804] br-lan: port 6(wlan1) entered disabled state
> <6>[ 14.993569] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
> <6>[ 15.000083] br-lan: port 5(wlan0) entered blocking state
> <6>[ 15.005416] br-lan: port 5(wlan0) entered forwarding state
> <6>[ 80.697698] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
> <6>[ 80.704212] br-lan: port 6(wlan1) entered blocking state
> <6>[ 80.709531] br-lan: port 6(wlan1) entered forwarding state
> <1>[20022.809676] Unable to handle kernel paging request at virtual address dead000000000110
> <1>[20022.817603] Mem abort info:
> <1>[20022.820417] ESR = 0x96000004
> <1>[20022.823463] EC = 0x25: DABT (current EL), IL = 32 bits
> <1>[20022.828764] SET = 0, FnV = 0
> <1>[20022.831824] EA = 0, S1PTW = 0
> <1>[20022.834967] Data abort info:
> <1>[20022.837837] ISV = 0, ISS = 0x00000004
> <1>[20022.841718] CM = 0, WnR = 0
> <1>[20022.844679] [dead000000000110] address between user and kernel address ranges
> <0>[20022.851856] Internal error: Oops: 96000004 [#1] SMP
> <7>[20022.856756] Modules linked in: pppoe ppp_async iptable_nat xt_state xt_nat xt_conntrack xt_REDIRECT xt_MASQUERADE xt_FLOWOFFLOAD xt_CT pppox ppp_generic nf_nat nf_flow_table nf_conntrack mt7915e mt7615e mt7615_common mt76_connac_lib mt76 mac80211 ipt_REJECT cfg80211 xt_time xt_tcpudp xt_multiport xt_mark xt_mac xt_limit xt_comment xt_TCPMSS xt_LOG slhc nf_reject_ipv4 nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 iptable_mangle iptable_filter ip_tables hwmon crc_ccitt compat nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 vfat fat autofs4 nls_utf8 nls_iso8859_1 nls_cp437 seqiv uas usb_storage leds_gpio xhci_plat_hcd gpio_button_hotplug
> <7>[20022.917650] CPU: 0 PID: 4340 Comm: kworker/u4:4 Tainted: G S 5.10.61 #0
> <7>[20022.925556] Hardware name: Linksys E8450 (UBI) (DT)
> <7>[20022.930436] Workqueue: nf_ft_offload_stats nf_flow_table_offload_setup [nf_flow_table]
> <7>[20022.938346] pstate: 20000005 (nzCv daif -PAN -UAO -TCO BTYPE=--)
> <7>[20022.944345] pc : nf_flow_offload_ipv6_hook+0x6c8/0x1250 [nf_flow_table]
> <7>[20022.950950] lr : nf_flow_offload_ipv6_hook+0x6dc/0x1250 [nf_flow_table]
> <7>[20022.957554] sp : ffffffc014533c30
> <7>[20022.960858] x29: ffffffc014533c30 x28: 0000000000000000
> <7>[20022.966163] x27: ffffff8002b60ac8 x26: ffffffc010aa4520
> <7>[20022.971467] x25: 0000000000000003 x24: ffffffc014533d68
> <7>[20022.976771] x23: ffffffc008ad5648 x22: 0000000000000002
> <7>[20022.982076] x21: ffffffc008ad5638 x20: 0000000000000000
> <7>[20022.987379] x19: dead0000000000f0 x18: 0000000000000000
> <7>[20022.992683] x17: 0000000000000001 x16: 0000000000000003
> <7>[20022.997986] x15: 0000000000000000 x14: 0000000000000000
> <7>[20023.003290] x13: 0000000000000011 x12: ffffffffffffffff
> <7>[20023.008595] x11: 0000000000000040 x10: 0000000000000000
> <7>[20023.013899] x9 : 0000000000000001 x8 : 0000000000000000
> <7>[20023.019204] x7 : ffffffffffffffff x6 : 0000000000000000
> <7>[20023.024508] x5 : 0000000000000003 x4 : 0000000000000000
> <7>[20023.029812] x3 : ffffff8000ba8b00 x2 : 0000000000000000
> <7>[20023.035115] x1 : dead000000000100 x0 : 000000000000006d
> <7>[20023.040419] Call trace:
> <7>[20023.042859] nf_flow_offload_ipv6_hook+0x6c8/0x1250 [nf_flow_table]
> <7>[20023.049117] nf_flow_table_offload_setup+0x450/0x650 [nf_flow_table]
> <7>[20023.055464] process_one_work+0x1d4/0x370
> <7>[20023.059464] worker_thread+0x178/0x4e0
> <7>[20023.063204] kthread+0x120/0x124
> <7>[20023.066424] ret_from_fork+0x10/0x18
> <0>[20023.069994] Code: d1004013 eb0002bf 54000560 52800014 (f9401263)
> <4>[20023.076078] ---[ end trace 8a5e0377171e08b0 ]---
> <0>[20023.087013] Kernel panic - not syncing: Oops: Fatal exception
> <2>[20023.092755] SMP: stopping secondary CPUs
> <0>[20023.096673] Kernel Offset: disabled
> <0>[20023.100152] CPU features: 0x0000002,04002004
> <0>[20023.104412] Memory Limit: none
> root@OpenWrt:~#
No error on old firmware, but many error I/O on new firmware (non-ubi)
[ 1.371250] blk_update_request: I/O error, dev mtdblock3, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 1.381610] Buffer I/O error on dev mtdblock3, logical block 0, async page read
[ 1.389056] blk_update_request: I/O error, dev mtdblock3, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 1.399404] Buffer I/O error on dev mtdblock3, logical block 0, async page read
[ 1.406848] blk_update_request: I/O error, dev mtdblock3, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 1.417193] Buffer I/O error on dev mtdblock3, logical block 0, async page read
[ 1.424504] mtdblock3: unable to read partition table
[ 1.432542] blk_update_request: I/O error, dev mtdblock6, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 1.442894] Buffer I/O error on dev mtdblock6, logical block 0, async page read
[ 1.450335] blk_update_request: I/O error, dev mtdblock6, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 1.460681] Buffer I/O error on dev mtdblock6, logical block 0, async page read
[ 1.468127] blk_update_request: I/O error, dev mtdblock6, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 1.478473] Buffer I/O error on dev mtdblock6, logical block 0, async page read
[ 1.485780] mtdblock6: unable to read partition table
[ 1.491280] blk_update_request: I/O error, dev mtdblock7, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 1.501627] Buffer I/O error on dev mtdblock7, logical block 0, async page read
[ 1.509071] blk_update_request: I/O error, dev mtdblock7, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 1.519418] Buffer I/O error on dev mtdblock7, logical block 0, async page read
[ 1.526861] blk_update_request: I/O error, dev mtdblock7, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 1.537206] Buffer I/O error on dev mtdblock7, logical block 0, async page read
hello @bobbythomas my device android don't connect to OpenWrt too
do you have a solution found in the past , thanks
Try using WPA2 AES and disable 802.11w
ok thanks i will try if i understand i disable
Where Wi-Fi Multimedia (WMM) Mode QoS is disabled, clients may be limited to 802.11a/802.11g rate
No Julien, I'm still trying to identify the issue. To clarify, I don't have any problem with android devices connecting to wifi, but the problem is with communication between WiFi devices (and wired devices - started seeing recently)
The issues seems to be not only related to wifi but also there are some issues in communication between wired and wireless. Sometimes there will be connectivity at other times there won't be any connectivity. With wired if I manually add the ARP entry of the WiFi device then I can communicate with them, so it something with ARP being blocked by the Openwrt AP.
1 Like
Ok, it's the xiaomi box that doesn't connect to wifi and if I put my classic livebox it connects directly
I tried this but still have issues with client to client or host to host communication (both wired and wireless). I don't think it's something related to WPA2 or 802.11w.
1 Like
ok it connects now by disabling wmm but has no internet access
while on my pc yes besides my wifi tests are really bad I do not understand in 2.4 ghz you put what bandwidth I put 20mhz
I settings in auto and put my country that is to say France
what else should I do ?
edit: dslreports is broken tonight