Hi Daniel,
Please find the output below.
root@OpenWrt:~# cat /sys/fs/pstore/*
Oops#1 Part1
<5>[ 7.338224] UBIFS (ubi0:5): UBIFS: mounted UBI device 0, volume 5, name "rootfs_data"
<5>[ 7.346056] UBIFS (ubi0:5): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
<5>[ 7.355979] UBIFS (ubi0:5): FS size: 91295744 bytes (87 MiB, 719 LEBs), journal size 4571136 bytes (4 MiB, 36 LEBs)
<5>[ 7.366410] UBIFS (ubi0:5): reserved for root: 4312123 bytes (4211 KiB)
<5>[ 7.373017] UBIFS (ubi0:5): media format: w5/r0 (latest is w5/r0), UUID 3015F212-EFD6-4299-9110-AB7B1C57E37D, small LPT model
<14>[ 7.513643] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
<14>[ 7.523378] block: extroot: not configured
<14>[ 7.528842] mount_root: switching to ubifs overlay
<6>[ 7.536458] overlayfs: "xino" feature enabled using 2 upper inode bits.
<15>[ 7.545939] urandom-seed: Seeding with /etc/urandom.seed
<6>[ 7.589196] mt7530 mdio-bus:00 lan1: Link is Down
<14>[ 7.598434] procd: - early -
<14>[ 7.601352] procd: - watchdog -
<14>[ 8.144788] procd: - watchdog -
<14>[ 8.149874] procd: - ubus -
<14>[ 8.203933] procd: - init -
<14>[ 8.497159] urngd: v1.0.2 started.
<14>[ 8.568882] kmodloader: loading kernel modules from /etc/modules.d/*
<6>[ 8.600475] Loading modules backported from Linux version v5.10.42-0-g65859eca4dff
<6>[ 8.608094] Backport generated by backports.git v5.10.42-1-0-gbee5c545
<6>[ 8.627198] xt_time: kernel timezone is -0000
<7>[ 8.683467] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
<7>[ 8.694264] mt7915e 0000:01:00.0: assign IRQ: got 144
<7>[ 8.699463] pci 0000:00:00.0: enabling bus mastering
<6>[ 8.704450] mt7915e 0000:01:00.0: enabling device (0000 -> 0002)
<7>[ 8.710564] mt7915e 0000:01:00.0: enabling bus mastering
<6>[ 8.746674] mt7622-wmac 18000000.wmac: HW/SW Version: 0x8a108a10, Build Time: 20190801210006a
<6>[ 8.746674]
<6>[ 8.778842] mt7915e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20201105222230a
<6>[ 8.778842]
<6>[ 8.847393] mt7622-wmac 18000000.wmac: N9 Firmware Version: 2.0, Build Time: 20200131180931
<6>[ 8.912506] mt7915e 0000:01:00.0: WM Firmware Version: ____000000, Build Time: 20201105222304
<6>[ 8.937183] mt7915e 0000:01:00.0: WA Firmware Version: DEV_000000, Build Time: 20201105222323
<6>[ 9.061285] PPP generic driver version 2.4.2
<6>[ 9.066766] NET: Registered protocol family 24
<14>[ 9.078466] kmodloader: done loading kernel modules from /etc/modules.d/*
<6>[ 11.727781] mtk_soc_eth 1b100000.ethernet eth0: Link is Down
<6>[ 11.736732] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
<6>[ 11.745239] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
<6>[ 11.753947] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
<6>[ 11.768929] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode
<6>[ 11.777996] 8021q: adding VLAN 0 to HW filter on device lan1
<6>[ 11.786055] br-lan: port 1(lan1) entered blocking state
<6>[ 11.791400] br-lan: port 1(lan1) entered disabled state
<6>[ 11.798499] device lan1 entered promiscuous mode
<6>[ 11.803122] device eth0 entered promiscuous mode
<6>[ 11.821101] mt7530 mdio-bus:00 lan2: configuring for phy/gmii link mode
<6>[ 11.835735] 8021q: adding VLAN 0 to HW filter on device lan2
<6>[ 11.849040] br-lan: port 2(lan2) entered blocking state
<6>[ 11.854269] br-lan: port 2(lan2) entered disabled state
<6>[ 11.896612] device lan2 entered promiscuous mode
<6>[ 11.913070] mt7530 mdio-bus:00 lan3: configuring for phy/gmii link mode
<6>[ 11.924644] 8021q: adding VLAN 0 to HW filter on device lan3
<6>[ 11.945679] br-lan: port 3(lan3) entered blocking state
<6>[ 11.951030] br-lan: port 3(lan3) entered disabled state
<6>[ 11.973057] device lan3 entered promiscuous mode
<6>[ 11.989451] mt7530 mdio-bus:00 lan4: configuring for phy/gmii link mode
<6>[ 12.002761] 8021q: adding VLAN 0 to HW filter on device lan4
<6>[ 12.028403] br-lan: port 4(lan4) entered blocking state
<6>[ 12.033644] br-lan: port 4(lan4) entered disabled state
<6>[ 12.041889] device lan4 entered promiscuous mode
<6>[ 12.054669] mt7530 mdio-bus:00 wan: configuring for phy/gmii link mode
<6>[ 12.062419] 8021q: adding VLAN 0 to HW filter on device wan
<6>[ 14.787495] br-lan: port 5(wlan1) entered blocking state
<6>[ 14.792824] br-lan: port 5(wlan1) entered disabled state
<6>[ 14.798399] device wlan1 entered promiscuous mode
<6>[ 14.803234] br-lan: port 5(wlan1) entered blocking state
<6>[ 14.808612] br-lan: port 5(wlan1) entered forwarding state
<6>[ 14.814995] br-lan: port 5(wlan1) entered disabled state
<6>[ 14.930986] mt7530 mdio-bus:00 lan1: Link is Up - 1Gbps/Full - flow control off
<6>[ 14.938413] br-lan: port 1(lan1) entered blocking state
<6>[ 14.943664] br-lan: port 1(lan1) entered forwarding state
<6>[ 14.952336] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
<6>[ 15.015310] br-lan: port 6(wlan0) entered blocking state
<6>[ 15.020718] br-lan: port 6(wlan0) entered disabled state
<6>[ 15.026305] device wlan0 entered promiscuous mode
<6>[ 15.031145] br-lan: port 6(wlan0) entered blocking state
<6>[ 15.036514] br-lan: port 6(wlan0) entered forwarding state
<6>[ 15.886372] br-lan: port 6(wlan0) entered disabled state
<6>[ 22.870463] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
<6>[ 22.876977] br-lan: port 6(wlan0) entered blocking state
<6>[ 22.882291] br-lan: port 6(wlan0) entered forwarding state
<6>[ 35.207122] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
<6>[ 35.213608] br-lan: port 5(wlan1) entered blocking state
<6>[ 35.218942] br-lan: port 5(wlan1) entered forwarding state
<1>[ 71.169440] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000053
<1>[ 71.178258] Mem abort info:
<1>[ 71.181043] ESR = 0x96000005
<1>[ 71.184089] EC = 0x25: DABT (current EL), IL = 32 bits
<1>[ 71.189405] SET = 0, FnV = 0
<1>[ 71.192449] EA = 0, S1PTW = 0
<1>[ 71.195579] Data abort info:
<1>[ 71.198458] ISV = 0, ISS = 0x00000005
<1>[ 71.202283] CM = 0, WnR = 0
<1>[ 71.205243] user pgtable: 4k pages, 39-bit VAs, pgdp=000000004140d000
<1>[ 71.211681] [0000000000000053] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000
<0>[ 71.220455] Internal error: Oops: 96000005 [#1] SMP
<7>[ 71.225356] Modules linked in: pppoe ppp_async iptable_nat xt_state xt_nat xt_conntrack xt_REDIRECT xt_MASQUERADE xt_FLOWOFFLOAD xt_CT pppox ppp_generic nf_nat nf_flow_table nf_conntrack mt7915e mt7615e mt7615_common mt76_connac_lib mt76 mac80211 ipt_REJECT cfg80211 xt_time xt_tcpudp xt_multiport xt_mark xt_mac xt_limit xt_comment xt_TCPMSS xt_LOG slhc nf_reject_ipv4 nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 ipvlan iptable_mangle iptable_filter ip_tables hwmon crc_ccitt compat nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 vfat fat autofs4 nls_utf8 nls_iso8859_1 nls_cp437 seqiv uas usb_storage leds_gpio xhci_plat_hcd gpio_button_hotplug
<7>[ 71.286861] CPU: 0 PID: 1157 Comm: napi/phy1-9 Tainted: G S 5.10.58 #0
<7>[ 71.294680] Hardware name: Linksys E8450 (UBI) (DT)
<7>[ 71.299549] pstate: 60000005 (nZCv daif -PAN -UAO -TCO BTYPE=--)
<7>[ 71.305557] pc : mt76_tx_status_skb_add+0x1b0/0x230 [mt76]
<7>[ 71.311035] lr : mt76_tx_status_skb_done+0x14/0x20 [mt76]
<7>[ 71.316422] sp : ffffffc010e23c10
<7>[ 71.319726] x29: ffffffc010e23c10 x28: ffffff800221a800
<7>[ 71.325031] x27: 00000000000036c0 x26: ffffff8002a6a300
<7>[ 71.330335] x25: 0000000040000000 x24: 0000000000000000
<7>[ 71.335640] x23: ffffff80038f7848 x22: ffffff800187bbb8
<7>[ 71.340945] x21: 0000000000000000 x20: ffffff80038f7828
<7>[ 71.346249] x19: ffffff800221a800 x18: 00000000419b6780
<7>[ 71.351553] x17: 0000000000000000 x16: 0000000000000001
<7>[ 71.356858] x15: 000000000000c5c0 x14: ffffff8002280000
<7>[ 71.362162] x13: 00000000000062e0 x12: 0000000000000000
<7>[ 71.367466] x11: 0000000000000000 x10: ffffffc010a89570
<7>[ 71.372771] x9 : ffffff801fec0530 x8 : 0000000003000000
<7>[ 71.378076] x7 : ffffff80022c0e80 x6 : 00000000ffffa688
<7>[ 71.383380] x5 : 00000000ffffa698 x4 : 0000000000000000
<7>[ 71.388684] x3 : ffffffc010e23d18 x2 : 0000000000000002
<7>[ 71.393989] x1 : 0000000000000000 x0 : ffffff800221a800
<7>[ 71.399294] Call trace:
<7>[ 71.401735] mt76_tx_status_skb_add+0x1b0/0x230 [mt76]
<7>[ 71.406868] mt7915_queue_rx_skb+0xbcc/0x1598 [mt7915e]
<7>[ 71.412087] mt76_dma_rx_poll+0x2bc/0xc98 [mt76]
<7>[ 71.416700] __napi_poll+0x38/0x170
<7>[ 71.420180] napi_threaded_poll+0x80/0xe8
<7>[ 71.424185] kthread+0x120/0x128
<7>[ 71.427407] ret_from_fork+0x10/0x18
<0>[ 71.430978] Code: a94153f3 a8c27bfd d65f03c0 d503201f (39414c24)
<4>[ 71.437062] ---[ end trace 92fbbbfe12521edd ]---
Panic#2 Part1
<5>[ 7.355979] UBIFS (ubi0:5): FS size: 91295744 bytes (87 MiB, 719 LEBs), journal size 4571136 bytes (4 MiB, 36 LEBs)
<5>[ 7.366410] UBIFS (ubi0:5): reserved for root: 4312123 bytes (4211 KiB)
<5>[ 7.373017] UBIFS (ubi0:5): media format: w5/r0 (latest is w5/r0), UUID 3015F212-EFD6-4299-9110-AB7B1C57E37D, small LPT model
<14>[ 7.513643] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
<14>[ 7.523378] block: extroot: not configured
<14>[ 7.528842] mount_root: switching to ubifs overlay
<6>[ 7.536458] overlayfs: "xino" feature enabled using 2 upper inode bits.
<15>[ 7.545939] urandom-seed: Seeding with /etc/urandom.seed
<6>[ 7.589196] mt7530 mdio-bus:00 lan1: Link is Down
<14>[ 7.598434] procd: - early -
<14>[ 7.601352] procd: - watchdog -
<14>[ 8.144788] procd: - watchdog -
<14>[ 8.149874] procd: - ubus -
<14>[ 8.203933] procd: - init -
<14>[ 8.497159] urngd: v1.0.2 started.
<14>[ 8.568882] kmodloader: loading kernel modules from /etc/modules.d/*
<6>[ 8.600475] Loading modules backported from Linux version v5.10.42-0-g65859eca4dff
<6>[ 8.608094] Backport generated by backports.git v5.10.42-1-0-gbee5c545
<6>[ 8.627198] xt_time: kernel timezone is -0000
<7>[ 8.683467] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
<7>[ 8.694264] mt7915e 0000:01:00.0: assign IRQ: got 144
<7>[ 8.699463] pci 0000:00:00.0: enabling bus mastering
<6>[ 8.704450] mt7915e 0000:01:00.0: enabling device (0000 -> 0002)
<7>[ 8.710564] mt7915e 0000:01:00.0: enabling bus mastering
<6>[ 8.746674] mt7622-wmac 18000000.wmac: HW/SW Version: 0x8a108a10, Build Time: 20190801210006a
<6>[ 8.746674]
<6>[ 8.778842] mt7915e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20201105222230a
<6>[ 8.778842]
<6>[ 8.847393] mt7622-wmac 18000000.wmac: N9 Firmware Version: 2.0, Build Time: 20200131180931
<6>[ 8.912506] mt7915e 0000:01:00.0: WM Firmware Version: ____000000, Build Time: 20201105222304
<6>[ 8.937183] mt7915e 0000:01:00.0: WA Firmware Version: DEV_000000, Build Time: 20201105222323
<6>[ 9.061285] PPP generic driver version 2.4.2
<6>[ 9.066766] NET: Registered protocol family 24
<14>[ 9.078466] kmodloader: done loading kernel modules from /etc/modules.d/*
<6>[ 11.727781] mtk_soc_eth 1b100000.ethernet eth0: Link is Down
<6>[ 11.736732] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
<6>[ 11.745239] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
<6>[ 11.753947] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
<6>[ 11.768929] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode
<6>[ 11.777996] 8021q: adding VLAN 0 to HW filter on device lan1
<6>[ 11.786055] br-lan: port 1(lan1) entered blocking state
<6>[ 11.791400] br-lan: port 1(lan1) entered disabled state
<6>[ 11.798499] device lan1 entered promiscuous mode
<6>[ 11.803122] device eth0 entered promiscuous mode
<6>[ 11.821101] mt7530 mdio-bus:00 lan2: configuring for phy/gmii link mode
<6>[ 11.835735] 8021q: adding VLAN 0 to HW filter on device lan2
<6>[ 11.849040] br-lan: port 2(lan2) entered blocking state
<6>[ 11.854269] br-lan: port 2(lan2) entered disabled state
<6>[ 11.896612] device lan2 entered promiscuous mode
<6>[ 11.913070] mt7530 mdio-bus:00 lan3: configuring for phy/gmii link mode
<6>[ 11.924644] 8021q: adding VLAN 0 to HW filter on device lan3
<6>[ 11.945679] br-lan: port 3(lan3) entered blocking state
<6>[ 11.951030] br-lan: port 3(lan3) entered disabled state
<6>[ 11.973057] device lan3 entered promiscuous mode
<6>[ 11.989451] mt7530 mdio-bus:00 lan4: configuring for phy/gmii link mode
<6>[ 12.002761] 8021q: adding VLAN 0 to HW filter on device lan4
<6>[ 12.028403] br-lan: port 4(lan4) entered blocking state
<6>[ 12.033644] br-lan: port 4(lan4) entered disabled state
<6>[ 12.041889] device lan4 entered promiscuous mode
<6>[ 12.054669] mt7530 mdio-bus:00 wan: configuring for phy/gmii link mode
<6>[ 12.062419] 8021q: adding VLAN 0 to HW filter on device wan
<6>[ 14.787495] br-lan: port 5(wlan1) entered blocking state
<6>[ 14.792824] br-lan: port 5(wlan1) entered disabled state
<6>[ 14.798399] device wlan1 entered promiscuous mode
<6>[ 14.803234] br-lan: port 5(wlan1) entered blocking state
<6>[ 14.808612] br-lan: port 5(wlan1) entered forwarding state
<6>[ 14.814995] br-lan: port 5(wlan1) entered disabled state
<6>[ 14.930986] mt7530 mdio-bus:00 lan1: Link is Up - 1Gbps/Full - flow control off
<6>[ 14.938413] br-lan: port 1(lan1) entered blocking state
<6>[ 14.943664] br-lan: port 1(lan1) entered forwarding state
<6>[ 14.952336] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
<6>[ 15.015310] br-lan: port 6(wlan0) entered blocking state
<6>[ 15.020718] br-lan: port 6(wlan0) entered disabled state
<6>[ 15.026305] device wlan0 entered promiscuous mode
<6>[ 15.031145] br-lan: port 6(wlan0) entered blocking state
<6>[ 15.036514] br-lan: port 6(wlan0) entered forwarding state
<6>[ 15.886372] br-lan: port 6(wlan0) entered disabled state
<6>[ 22.870463] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
<6>[ 22.876977] br-lan: port 6(wlan0) entered blocking state
<6>[ 22.882291] br-lan: port 6(wlan0) entered forwarding state
<6>[ 35.207122] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
<6>[ 35.213608] br-lan: port 5(wlan1) entered blocking state
<6>[ 35.218942] br-lan: port 5(wlan1) entered forwarding state
<1>[ 71.169440] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000053
<1>[ 71.178258] Mem abort info:
<1>[ 71.181043] ESR = 0x96000005
<1>[ 71.184089] EC = 0x25: DABT (current EL), IL = 32 bits
<1>[ 71.189405] SET = 0, FnV = 0
<1>[ 71.192449] EA = 0, S1PTW = 0
<1>[ 71.195579] Data abort info:
<1>[ 71.198458] ISV = 0, ISS = 0x00000005
<1>[ 71.202283] CM = 0, WnR = 0
<1>[ 71.205243] user pgtable: 4k pages, 39-bit VAs, pgdp=000000004140d000
<1>[ 71.211681] [0000000000000053] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000
<0>[ 71.220455] Internal error: Oops: 96000005 [#1] SMP
<7>[ 71.225356] Modules linked in: pppoe ppp_async iptable_nat xt_state xt_nat xt_conntrack xt_REDIRECT xt_MASQUERADE xt_FLOWOFFLOAD xt_CT pppox ppp_generic nf_nat nf_flow_table nf_conntrack mt7915e mt7615e mt7615_common mt76_connac_lib mt76 mac80211 ipt_REJECT cfg80211 xt_time xt_tcpudp xt_multiport xt_mark xt_mac xt_limit xt_comment xt_TCPMSS xt_LOG slhc nf_reject_ipv4 nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 ipvlan iptable_mangle iptable_filter ip_tables hwmon crc_ccitt compat nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 vfat fat autofs4 nls_utf8 nls_iso8859_1 nls_cp437 seqiv uas usb_storage leds_gpio xhci_plat_hcd gpio_button_hotplug
<7>[ 71.286861] CPU: 0 PID: 1157 Comm: napi/phy1-9 Tainted: G S 5.10.58 #0
<7>[ 71.294680] Hardware name: Linksys E8450 (UBI) (DT)
<7>[ 71.299549] pstate: 60000005 (nZCv daif -PAN -UAO -TCO BTYPE=--)
<7>[ 71.305557] pc : mt76_tx_status_skb_add+0x1b0/0x230 [mt76]
<7>[ 71.311035] lr : mt76_tx_status_skb_done+0x14/0x20 [mt76]
<7>[ 71.316422] sp : ffffffc010e23c10
<7>[ 71.319726] x29: ffffffc010e23c10 x28: ffffff800221a800
<7>[ 71.325031] x27: 00000000000036c0 x26: ffffff8002a6a300
<7>[ 71.330335] x25: 0000000040000000 x24: 0000000000000000
<7>[ 71.335640] x23: ffffff80038f7848 x22: ffffff800187bbb8
<7>[ 71.340945] x21: 0000000000000000 x20: ffffff80038f7828
<7>[ 71.346249] x19: ffffff800221a800 x18: 00000000419b6780
<7>[ 71.351553] x17: 0000000000000000 x16: 0000000000000001
<7>[ 71.356858] x15: 000000000000c5c0 x14: ffffff8002280000
<7>[ 71.362162] x13: 00000000000062e0 x12: 0000000000000000
<7>[ 71.367466] x11: 0000000000000000 x10: ffffffc010a89570
<7>[ 71.372771] x9 : ffffff801fec0530 x8 : 0000000003000000
<7>[ 71.378076] x7 : ffffff80022c0e80 x6 : 00000000ffffa688
<7>[ 71.383380] x5 : 00000000ffffa698 x4 : 0000000000000000
<7>[ 71.388684] x3 : ffffffc010e23d18 x2 : 0000000000000002
<7>[ 71.393989] x1 : 0000000000000000 x0 : ffffff800221a800
<7>[ 71.399294] Call trace:
<7>[ 71.401735] mt76_tx_status_skb_add+0x1b0/0x230 [mt76]
<7>[ 71.406868] mt7915_queue_rx_skb+0xbcc/0x1598 [mt7915e]
<7>[ 71.412087] mt76_dma_rx_poll+0x2bc/0xc98 [mt76]
<7>[ 71.416700] __napi_poll+0x38/0x170
<7>[ 71.420180] napi_threaded_poll+0x80/0xe8
<7>[ 71.424185] kthread+0x120/0x128
<7>[ 71.427407] ret_from_fork+0x10/0x18
<0>[ 71.430978] Code: a94153f3 a8c27bfd d65f03c0 d503201f (39414c24)
<4>[ 71.437062] ---[ end trace 92fbbbfe12521edd ]---
<0>[ 71.447848] Kernel panic - not syncing: Oops: Fatal exception in interrupt
<2>[ 71.454719] SMP: stopping secondary CPUs
<0>[ 71.458637] Kernel Offset: disabled
<0>[ 71.462118] CPU features: 0x0000002,04002004
<0>[ 71.466377] Memory Limit: none
root@OpenWrt:~#
Regards,
Bob