I had your previous image from your repo 2023-01-08-1438 working well and something is or went wrong when I flashed your last image 2023-01-09-2026-openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin from today.
After flash the router gets into a boot loop, with orange led on for a period of time, then off briefly, then repeats.
This what I capture from UART:
resetting ...
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00147
S - IMAGE_VARIANT_STRING=HAACANAAA
S - OEM_IMAGE_VERSION_STRING=xiaoyang-gv
S - Boot Config, 0x000002e5
B - 201 - PBL, Start
B - 2736 - bootable_media_detect_entry, Start
B - 3444 - bootable_media_detect_success, Start
B - 3448 - elf_loader_entry, Start
B - 6116 - auth_hash_seg_entry, Start
B - 6359 - auth_hash_seg_exit, Start
B - 68593 - elf_segs_hash_verify_entry, Start
B - 131293 - PBL, End
B - 207095 - SBL1, Start
B - 283467 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B - 292861 - pm_device_init, Start
B - 466436 - PM_SET_VAL:Skip
D - 171593 - pm_device_init, Delta
B - 468724 - pm_driver_init, Start
D - 5368 - pm_driver_init, Delta
B - 475159 - clock_init, Start
D - 2135 - clock_init, Delta
B - 479216 - boot_flash_init, Start
D - 11864 - boot_flash_init, Delta
B - 494771 - boot_config_data_table_init, Start
D - 3202 - boot_config_data_table_init, Delta - (575 Bytes)
B - 502274 - Boot Setting : 0x00000600
B - 506208 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:16
B - 513132 - sbl1_ddr_set_params, Start
B - 516975 - CPR configuration: 0x300
B - 520452 - cpr_init, Start
B - 523227 - Rail:0 Mode: 5 Voltage: 784000
B - 528382 - CL CPR settled at 736000mV
B - 531218 - Rail:1 Mode: 5 Voltage: 880000
B - 535397 - Rail:1 Mode: 7 Voltage: 888000
D - 16470 - cpr_init, Delta
B - 542259 - Pre_DDR_clock_init, Start
B - 546285 - Pre_DDR_clock_init, End
B - 549671 - DDR Type : PCDDR3
B - 555374 - do ddr sanity test, Start
D - 1067 - do ddr sanity test, Delta
B - 560132 - DDR: Start of HAL DDR Boot Training
B - 564890 - DDR: End of HAL DDR Boot Training
B - 570563 - DDR: Checksum to be stored on flash is 1155630626
B - 580964 - Image Load, Start
D - 224144 - QSEE Image Loaded, Delta - (1373936 Bytes)
B - 805200 - Image Load, Start
D - 61 - SEC Image Loaded, Delta - (0 Bytes)
B - 812855 - Image Load, Start
D - 10706 - DEVCFG Image Loaded, Delta - (26004 Bytes)
B - 823652 - Image Load, Start
D - 25254 - RPM Image Loaded, Delta - (105964 Bytes)
B - 848967 - Image Load, Start
D - 96563 - APPSBL Image Loaded, Delta - (589900 Bytes)
B - 945652 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 951447 - USB D+ check, Start
D - 0 - USB D+ check, Delta
B - 957852 - SBL1, End
D - 753075 - SBL1, Delta
S - Flash Throughput, 6749 KB/s (2096379 Bytes, 310607 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 800 MHz
U-Boot 2016.01 (Sep 28 2020 - 09:05:55 +0000), Build: jenkins-common_router_openwrt_ota_publish-383
DRAM: smem ram ptable found: ver: 1 len: 4
512 MiB
NAND: ONFI device found
ID = 1590aac8
Vendor = c8
Device = aa
qpic_nand: changing oobsize to 64 from 128 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
256 MiB
MMC: sdhci: Node Not found, skipping initialization
PCI Link Intialized
PCI1 is not defined in the device tree
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
Boot failure detected on both systems
machid: 8010010
MMC Device 0 not found
eth5 MAC Address from ART is not valid
write phy_id=1, reg(0x8074):0x0670
write phy_id=2, reg(0x8074):0x0670
write phy_id=3, reg(0x8074):0x0670
write phy_id=4, reg(0x8074):0x0670
bootwait is on, bootdelay=5
Hit any key to stop autoboot: 5 4 3 2 1 0
trigger button release!
Boot failure detected on both systems
boot from rootfs 1
miwifi: check crash in rmem !
ubi0: attaching mtd1
ubi0: scanning is finished
UBI init error 22
Erasing NAND...
Erasing at 0x680000 -- 25% complete.
Erasing at 0x6a0000 -- 50% complete.
Erasing at 0x6c0000 -- 75% complete.
Erasing at 0x6e0000 -- 100% complete.
Writing to NAND... OK
resetting ...
IPQ807x# smeminfo
flash_type: 0x2
flash_index: 0x0
flash_chip_select: 0x0
flash_block_size: 0x20000
flash_density: 0x100000
partition table offset 0x0
No.: Name Attributes Start Size
0: 0:SBL1 0x0000ffff 0x0 0x100000
1: 0:MIBIB 0x0000ffff 0x100000 0x100000
2: 0:QSEE 0x0000ffff 0x200000 0x300000
3: 0:DEVCFG 0x0000ffff 0x500000 0x80000
4: 0:RPM 0x0000ffff 0x580000 0x80000
5: 0:CDT 0x0000ffff 0x600000 0x80000
6: 0:APPSBLENV 0x0000ffff 0x680000 0x80000
7: 0:APPSBL 0x0000ffff 0x700000 0x100000
8: 0:ART 0x0000ffff 0x800000 0x80000
9: bdata 0x0000ffff 0x880000 0x80000
10: crash 0x0000ffff 0x900000 0x80000
11: crash_syslog 0x0000ffff 0x980000 0x80000
12: rootfs 0x0000ffff 0xa00000 0x23c0000
13: rootfs_1 0x0000ffff 0x2dc0000 0x23c0000
14: overlay 0x0000ffff 0x5180000 0x1ec0000
15: rsvd0 0x0000ffff 0x7040000 0x80000
I don't understand why I got the old partitions back, with rootfs and rootfs_1.
I'm 100% sure, I had the expanded rootfs before, I did confirmed it.