I'm not too sure on the answer to your question, maybe @robimarko any knowledge on this?
yeah this didnt work for me got cant get kernel image
Sadly, I have no information about the Linksys dual FW logic
This is what the partition layout looks like in OEM firmware:
and after install OpenWrt:
s_env partition is used for saving information about boot count. After 3 unsuccessful boots partitions are switched.
In the OEM firmware we have only one partition (syscfg) where changes are saved.
After installing OpenWrt on both partitions we have two separate rootfs_data volumes.
Ok, so they are using one partition as a big overlay.
But I am failing to see what is the issue with OpenWrt except for the smaller space?
If we are currently on partition1 and we are doing sysupgrade on partition2 with keeping the configuration (without -n option) should we synchronize rootfs_data between two separate ubi volumes?
No, rootfs_data is the upperdir for overlayfs and should not be synced, it should just be wiped during sysupgrade.
Config data is packaged during sysupgrade and appended so it gets restored on first boot
Currently, it works like this: if I configure WiFi and then upgrade, this WiFi configuration is not there after the restart.
Can you post the whole bootlog
partition1:
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00147
S - IMAGE_VARIANT_STRING=HAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e5
B - 201 - PBL, Start
B - 2736 - bootable_media_detect_entry, Start
B - 3443 - bootable_media_detect_success, Start
B - 3447 - elf_loader_entry, Start
B - 6112 - auth_hash_seg_entry, Start
B - 6355 - auth_hash_seg_exit, Start
B - 68495 - elf_segs_hash_verify_entry, Start
B - 131191 - PBL, End
B - 213561 - SBL1, Start
B - 291397 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B - 301096 - pm_device_init, Start
B - 480741 - PM_SET_VAL:Skip
D - 177662 - pm_device_init, Delta
B - 483028 - pm_driver_init, Start
D - 5368 - pm_driver_init, Delta
B - 489464 - clock_init, Start
D - 2104 - clock_init, Delta
B - 493520 - boot_flash_init, Start
D - 12688 - boot_flash_init, Delta
B - 509960 - boot_config_data_table_init, Start
D - 3141 - boot_config_data_table_init, Delta - (575 Bytes)
B - 517432 - Boot Setting : 0x00000618
B - 521458 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:8
B - 528260 - sbl1_ddr_set_params, Start
B - 532072 - CPR configuration: 0x30c
B - 535549 - cpr_init, Start
B - 538325 - Rail:0 Mode: 5 Voltage: 832000
B - 543510 - CL CPR settled at 784000mV
B - 546346 - Rail:1 Mode: 5 Voltage: 904000
B - 550525 - Rail:1 Mode: 7 Voltage: 944000
D - 16531 - cpr_init, Delta
B - 557418 - Pre_DDR_clock_init, Start
B - 561413 - Pre_DDR_clock_init, End
B - 564829 - DDR Type : PCDDR3
B - 570563 - do ddr sanity test, Start
D - 1067 - do ddr sanity test, Delta
B - 575321 - DDR: Start of HAL DDR Boot Training
B - 579957 - DDR: End of HAL DDR Boot Training
B - 585752 - DDR: Checksum to be stored on flash is 96661726
B - 595878 - Image Load, Start
D - 225822 - QSEE Image Loaded, Delta - (1373936 Bytes)
B - 821792 - Image Load, Start
D - 61 - SEC Image Loaded, Delta - (0 Bytes)
B - 829478 - Image Load, Start
D - 10736 - DEVCFG Image Loaded, Delta - (26004 Bytes)
B - 840305 - Image Load, Start
D - 25407 - RPM Image Loaded, Delta - (105964 Bytes)
B - 865803 - Image Load, Start
D - 102785 - APPSBL Image Loaded, Delta - (627152 Bytes)
B - 968710 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 974536 - USB D+ check, Start
D - 0 - USB D+ check, Delta
B - 980941 - SBL1, End
D - 769667 - SBL1, Delta
S - Flash Throughput, 6681 KB/s (2134303 Bytes, 319449 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 1651 MHz
U-Boot 2016.01 (Mar 13 2020 - 17:34:10 +0800)
version: 0.3.14
DRAM: smem ram ptable found: ver: 1 len: 4
1 GiB
board_devinfo_offset=1060000, board_devinfo_size=20000
board_senv_offset=1040000, board_senv_size=20000
board_kernel_offset=0x1080000, board_fw_size=0x9600000, board_altkernel_offset=0xa680000\nNAND: ONFI device found
ID = 1590acad
Vendor = ad
Device = ac
qpic_nand: changing oobsize to 64 from 128 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
512 MiB
MMC: <NULL>: 0
devinfo_import--devinfo_mem_pool.crc=b107910
fun=cmd_init DEVINFO_ITEMS=511
devinfo: data is valid!
qpic_nand_read_oob: ecc failure while reading from 1040000
NAND read from offset 1040000 failed -74
read senv fail
*** Warning - readsenv() failed, using default senv
qpic_nand_read_oob: ecc failure while reading from 1040000
@@ nand_read error
#### auto_recovery enabled:1, boot_part:1, boot_part_ready:3, boot_count=0
####[boot_count_write] erase:0, auto_recovery->block_offset:0x1040000 offset=0x1057000
Updating boot_count ...
####[boot_count_write] offset:0x1057000 , length:2048
done
PCI Link Intialized
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010008
Card did not respond to voltage select!
eth0 MAC Address from ART is not valid
eth1 MAC Address from ART is not valid
eth2 MAC Address from ART is not valid
eth3 MAC Address from ART is not valid
eth4 MAC Address from ART is not valid
eth5 MAC Address from ART is not valid
auto_recovery_check changes bootcmd: boot from partition 1
Bus 0: i2c@78b6000
Setting bus to 0
Valid chip addresses: 62 68
Hit 'Space' or 'Enter' key to stop autoboot: 0
Normal boot
starting USB...
USB0: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 0 for devices... 1 USB Device(s) found
USB1: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 1 for devices... 1 USB Device(s) found
** Bad device usb 0 **
NAND read: device 0 offset 0x13e80000, size 0x80000
524288 bytes read: OK
Erasing NAND...
Erasing at 0x1020000 -- 100% complete.
Writing to NAND... OK
PHY::Scratchpad Read/Write test fail
Disable 50MHz clock...
Erasing NAND...
Erasing at 0x1020000 -- 100% complete.
Writing to NAND... OK
NAND read: device 0 offset 0x1080000, size 0x600000
6291456 bytes read: OK
## Loading kernel from FIT Image at 44000000 ...
Using 'config@1' configuration
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-6.1.62
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x440000e8
Data Size: 4876367 Bytes = 4.7 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x41000000
Entry Point: 0x41000000
Hash algo: crc32
Hash value: 24e8ed6e
Hash algo: sha1
Hash value: c67bf06552491008add72e8d576eb20586c637e3
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
Using 'config@1' configuration
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt linksys_mx5300 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x444a6a78
Data Size: 46094 Bytes = 45 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: cb2e623f
Hash algo: sha1
Hash value: 09e35e8128a6c41d6349a5c659599a294e16c55d
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x444a6a78
Uncompressing Kernel Image ... OK
Loading Device Tree to 4a3f1000, end 4a3ff40d ... OK
Using machid 0x8010008 from environment
Starting kernel ...
Jumping to AARCH64 kernel via monitor
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 6.1.62 (a@a) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r24415-9062e5faae) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Sat Nov 18 11:23:54 2023
[ 0.000000] Machine model: Linksys MX5300
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000040ffffff]
[ 0.000000] node 0: [mem 0x0000000041000000-0x000000004a3fffff]
[ 0.000000] node 0: [mem 0x000000004a400000-0x00000000510fffff]
[ 0.000000] node 0: [mem 0x0000000051100000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] psci: OSI mode supported.
[ 0.000000] psci: failed to set PC mode: -1
[ 0.000000] percpu: Embedded 17 pages/cpu s31080 r8192 d30360 u69632
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048
[ 0.000000] Kernel command line: console=ttyMSM0,115200n8 ubi.mtd=rootfs root=ubi0:ubifs rootfstype=ubifs rootwait swiotlb=1 root=/dev/ubiblock0_0 rootfstype=squashfs ro
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 887712K/1048576K available (7744K kernel code, 854K rwdata, 2268K rodata, 1280K init, 273K bss, 160864K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479]
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000001] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000107] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.000120] pid_max: default: 32768 minimum: 301
[ 0.000600] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.000614] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.002442] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.002450] cblist_init_generic: Setting shift to 2 and lim to 1.
[ 0.002644] rcu: Hierarchical SRCU implementation.
[ 0.002648] rcu: Max phase no-delay instances is 1000.
[ 0.003481] smp: Bringing up secondary CPUs ...
[ 0.004117] Detected VIPT I-cache on CPU1
[ 0.004261] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.004924] Detected VIPT I-cache on CPU2
[ 0.005026] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.005639] Detected VIPT I-cache on CPU3
[ 0.005736] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.005802] smp: Brought up 1 node, 4 CPUs
[ 0.005810] SMP: Total of 4 processors activated.
[ 0.005815] CPU features: detected: 32-bit EL0 Support
[ 0.005820] CPU features: detected: CRC32 instructions
[ 0.005882] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.005888] CPU: All CPU(s) started at EL1
[ 0.005891] alternatives: applying system-wide alternatives
[ 0.016877] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.016904] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.017122] pinctrl core: initialized pinctrl subsystem
[ 0.018276] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.018857] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.018902] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.018937] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.019362] thermal_sys: Registered thermal governor 'step_wise'
[ 0.019543] cpuidle: using governor menu
[ 0.019862] ASID allocator initialised with 65536 entries
[ 0.073505] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 0.082026] SCSI subsystem initialized
[ 0.082212] usbcore: registered new interface driver usbfs
[ 0.082264] usbcore: registered new interface driver hub
[ 0.082299] usbcore: registered new device driver usb
[ 0.082733] qcom_scm: convention: smc arm 64
[ 0.084064] clocksource: Switched to clocksource arch_sys_counter
[ 0.085164] NET: Registered PF_INET protocol family
[ 0.085308] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.086616] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.086640] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.086667] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.086755] TCP bind hash table entries: 8192 (order: 6, 262144 bytes, linear)
[ 0.087028] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.087125] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.087162] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.087381] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.087419] PCI: CLS 0 bytes, default 64
[ 0.088835] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[ 0.093853] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.093866] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.098266] qcom-qmp-usb-phy 78000.phy: supply vdda-phy not found, using dummy regulator
[ 0.098417] qcom-qmp-usb-phy 78000.phy: supply vdda-pll not found, using dummy regulator
[ 0.100154] qcom-qusb2-phy 79000.phy: supply vdd not found, using dummy regulator
[ 0.100305] qcom-qusb2-phy 79000.phy: supply vdda-pll not found, using dummy regulator
[ 0.100372] qcom-qusb2-phy 79000.phy: supply vdda-phy-dpdm not found, using dummy regulator
[ 0.100531] qcom-qusb2-phy 79000.phy: Registered Qcom-QUSB2 phy
[ 0.102781] qcom-pcie 10000000.pci: host bridge /soc/pci@10000000 ranges:
[ 0.102832] qcom-pcie 10000000.pci: IO 0x0010200000..0x001020ffff -> 0x0000000000
[ 0.102857] qcom-pcie 10000000.pci: MEM 0x0010220000..0x001fffffff -> 0x0010220000
[ 0.161770] qcom-pcie 10000000.pci: Read DBI address failed
[ 0.265676] qcom-pcie 10000000.pci: iATU unroll: disabled
[ 0.265684] qcom-pcie 10000000.pci: iATU regions: 32 ob, 8 ib, align 4K, limit 4G
[ 0.365779] qcom-pcie 10000000.pci: PCIe Gen.2 x1 link up
[ 0.365961] qcom-pcie 10000000.pci: PCI host bridge to bus 0001:00
[ 0.365972] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.365983] pci_bus 0001:00: root bus resource [io 0x0000-0xffff]
[ 0.365992] pci_bus 0001:00: root bus resource [mem 0x10220000-0x1fffffff]
[ 0.366031] pci 0001:00:00.0: [17cb:0302] type 01 class 0x060400
[ 0.366051] pci 0001:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff]
[ 0.366120] pci 0001:00:00.0: PME# supported from D0 D3hot D3cold
[ 0.369790] pci 0001:01:00.0: [168c:0046] type 00 class 0x028000
[ 0.369943] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.370700] pci 0001:01:00.0: supports D1
[ 0.370708] pci 0001:01:00.0: PME# supported from D0 D1 D3hot D3cold
[ 0.394253] pci 0001:00:00.0: BAR 8: assigned [mem 0x10400000-0x105fffff]
[ 0.394268] pci 0001:00:00.0: BAR 0: assigned [mem 0x10220000-0x10220fff]
[ 0.394284] pci 0001:01:00.0: BAR 0: assigned [mem 0x10400000-0x105fffff 64bit]
[ 0.394358] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[ 0.394369] pci 0001:00:00.0: bridge window [mem 0x10400000-0x105fffff]
[ 0.396555] pcieport 0001:00:00.0: PME: Signaling with IRQ 16
[ 0.396851] pcieport 0001:00:00.0: AER: enabled with IRQ 16
[ 0.400316] bam-dma-engine 704000.dma-controller: num-channels unspecified in dt
[ 0.400332] bam-dma-engine 704000.dma-controller: num-ees unspecified in dt
[ 0.404826] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.405514] msm_serial 78b3000.serial: msm_serial: detected port #0
[ 0.405552] msm_serial 78b3000.serial: uartclk = 3686400
[ 0.405647] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 21, base_baud = 230400) is a MSM
[ 0.405676] msm_serial: console setup on port #0
[ 1.230589] printk: console [ttyMSM0] enabled
[ 1.235719] msm_serial: driver initialized
[ 1.244608] loop: module loaded
[ 1.246058] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xac
[ 1.246567] nand: Hynix H27S4G8F2EDA-BC
[ 1.253157] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
[ 1.257095] 29 fixed-partitions partitions found on MTD device qcom_nand.0
[ 1.264399] Creating 29 MTD partitions on "qcom_nand.0":
[ 1.271306] 0x000000000000-0x000000100000 : "0:sbl1"
[ 1.278366] 0x000000100000-0x000000200000 : "0:mibib"
[ 1.283140] 0x000000200000-0x000000280000 : "0:bootconfig"
[ 1.287680] 0x000000280000-0x000000300000 : "0:bootconfig1"
[ 1.293052] 0x000000300000-0x000000600000 : "0:qsee"
[ 1.300845] 0x000000600000-0x000000900000 : "0:qsee_1"
[ 1.306084] 0x000000900000-0x000000980000 : "0:devcfg"
[ 1.308620] 0x000000980000-0x000000a00000 : "0:devcfg_1"
[ 1.313731] 0x000000a00000-0x000000a80000 : "0:apdp"
[ 1.319268] 0x000000a80000-0x000000b00000 : "0:apdp_1"
[ 1.324248] 0x000000b00000-0x000000b80000 : "0:rpm"
[ 1.329128] 0x000000b80000-0x000000c00000 : "0:rpm_1"
[ 1.333936] 0x000000c00000-0x000000c80000 : "0:cdt"
[ 1.339168] 0x000000c80000-0x000000d00000 : "0:cdt_1"
[ 1.343809] 0x000000d00000-0x000000d80000 : "0:appsblenv"
[ 1.349074] 0x000000d80000-0x000000e80000 : "0:appsbl"
[ 1.354912] 0x000000e80000-0x000000f80000 : "0:appsbl_1"
[ 1.359881] 0x000000f80000-0x000001000000 : "0:art"
[ 1.364959] 0x000001000000-0x000001040000 : "u_env"
[ 1.369271] 0x000001040000-0x000001060000 : "s_env"
[ 1.373985] 0x000001060000-0x000001080000 : "devinfo"
[ 1.378869] 0x000001080000-0x00000a680000 : "kernel"
[ 1.527371] 0x000001680000-0x00000a680000 : "rootfs"
[ 1.665400] mtd: setting mtd22 (rootfs) as root device
[ 1.665756] mtdsplit: no squashfs found in "rootfs"
[ 1.669445] 0x00000a680000-0x000013c80000 : "alt_kernel"
[ 1.817814] 0x00000ac80000-0x000013c80000 : "alt_rootfs"
[ 1.956881] 0x000013c80000-0x000013e80000 : "sysdiag"
[ 1.959297] 0x000013e80000-0x000013f00000 : "0:ethphyfw"
[ 1.961809] 0x000013f00000-0x00001f700000 : "syscfg"
[ 2.142968] 0x00001f700000-0x000020000000 : "0:wififw"
[ 2.161689] spmi spmi-0: PMIC arbiter version v2 (0x20010000)
[ 2.186344] i2c_dev: i2c /dev entries driver
[ 2.193364] sdhci: Secure Digital Host Controller Interface driver
[ 2.193406] sdhci: Copyright(c) Pierre Ossman
[ 2.198463] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.204608] remoteproc remoteproc0: releasing cd00000.q6v5_wcss
[ 2.211301] NET: Registered PF_INET6 protocol family
[ 2.215267] Segment Routing with IPv6
[ 2.219470] In-situ OAM (IOAM) with IPv6
[ 2.223071] NET: Registered PF_PACKET protocol family
[ 2.227054] 8021q: 802.1Q VLAN Support v1.8
[ 2.251016] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 2.251316] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
[ 2.257360] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1
[ 2.263742] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[ 2.271416] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[ 2.278922] cpr3_mem_acc_init: apc: not using memory accelerator regulator
[ 2.288055] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 704000 uV
[ 2.295004] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 832000 uV
[ 2.304987] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 896000 uV
[ 2.314794] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop=1000000 uV
[ 2.324655] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 679, quot_offset[ 7]= 0
[ 2.334416] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 906, quot_offset[ 7]= 225
[ 2.345265] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]=1006, quot_offset[ 7]= 100
[ 2.356203] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]=1175, quot_offset[ 7]= 165
[ 2.367327] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
[ 2.370266] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 800000 KHz, changing to: 1017600 KHz
[ 2.386599] remoteproc remoteproc0: cd00000.q6v5_wcss is available
[ 2.395969] ubi0: attaching mtd22
[ 2.674074] random: crng init done
[ 3.225263] ubi0: scanning is finished
[ 3.233337] ubi0: attached mtd22 (name "rootfs", size 144 MiB)
[ 3.233376] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.238087] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.244931] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.251784] ubi0: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 3.258556] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 3.264811] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1332887306
[ 3.271927] ubi0: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 80
[ 3.281227] ubi0: background thread "ubi_bgt0d" started, PID 5�[ 3.300160] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 3.300575] Freeing unused kernel memory: 1280K
[ 3.334192] Run /sbin/init as init process
[ 3.467313] init: Console is alive
[ 3.467480] init: - watchdog -
[ 4.056156] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.129385] ssdk_dt_parse_interrupt[916]:INFO:intr-gpio does not exist
[ 4.186644] ssdk_phy_driver_init[371]:INFO:dev_id = 0, phy_adress = 5, phy_id = 0x6820805 phytype doesn't match
[ 4.186695] malibu_phy_api_ops_init[1934]:INFO:qca probe malibu phy driver succeeded!
[ 5.236307] regi_init[3603]:INFO:Initializing HPPE Done!!
[ 5.236411] regi_init[3662]:INFO:qca-ssdk module init succeeded!
[ 5.242436] EDMA ver 1 hw init
[ 5.246992] EDMA HW Reset completed succesfully
[ 5.249654] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7)
[ 5.254057] RxDesc:1 (15-15) RxFill:1 (7-7)
[ 5.263380] **********************************************************
[ 5.263431] * NSS Data Plane driver
[ 5.270054] **********************************************************
[ 5.348771] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 5.348822] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1
[ 5.353297] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000000002010010
[ 5.360797] xhci-hcd xhci-hcd.1.auto: irq 38, io mem 0x08a00000
[ 5.370220] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 5.375999] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2
[ 5.381548] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 5.389579] hub 1-0:1.0: USB hub found
[ 5.395720] hub 1-0:1.0: 1 port detected
[ 5.399698] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 5.403987] hub 2-0:1.0: USB hub found
[ 5.411605] hub 2-0:1.0: 1 port detected
[ 5.417855] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.425470] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.874489] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 7.857872] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 7.857982] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 794
[ 7.901509] UBIFS (ubi0:1): recovery needed
[ 7.934767] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 8.000048] UBIFS (ubi0:1): recovery completed
[ 8.000142] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 8.003401] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 8.011329] UBIFS (ubi0:1): FS size: 126722048 bytes (120 MiB, 998 LEBs), max 1009 LEBs, journal size 6348800 bytes (6 MiB, 50 LEBs)
[ 8.021207] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[ 8.033173] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 0C9BA787-19B0-4840-A2E8-5C8D6E01AEED, small LPT model
[ 8.043340] mount_root: switching to ubifs overlay
[ 8.055463] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[ 8.060879] urandom-seed: Seeding with /etc/urandom.seed
[ 8.111711] procd: - early -
[ 8.111803] procd: - watchdog -
[ 8.657169] procd: - watchdog -
[ 8.657718] procd: - ubus -
[ 8.715522] procd: - init -
Please press Enter to activate this console.
[ 8.895567] kmodloader: loading kernel modules from /etc/modules.d/*
[ 8.933322] Loading modules backported from Linux version v6.5-0-g2dde18cd1d8f
[ 8.933362] Backport generated by backports.git v5.15.92-1-56-g5fb2ccb6b9e8
[ 8.944316] NET: Registered PF_QIPCRTR protocol family
[ 8.948587] rtc-ds1307 0-0068: registered as rtc0
[ 8.951788] rtc-ds1307 0-0068: setting system clock to 2023-11-19T13:55:29 UTC (1700402129)
[ 8.964488] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 8.981852] PPP generic driver version 2.4.2
[ 8.982567] NET: Registered PF_PPPOX protocol family
[ 8.991467] ath10k 6.4 driver, optimized for CT firmware, probing pci device: 0x46.
[ 8.991872] ath10k_pci 0001:01:00.0: enabling device (0000 -> 0002)
[ 8.998501] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 9.058478] urngd: v1.0.2 started.
[ 9.614823] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 9.614874] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 9.624012] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 7ea63dc5
[ 9.994529] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 11.034512] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 11.919794] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id N/A crc32 56d3acd2
[ 12.074499] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 13.120784] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 13.120848] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[ 13.124433] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 13.203873] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 13.204674] ath10k_pci 0001:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224'
[ 13.493479] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal nvmem max-sta 32 raw 0 hwcrypto 1
[ 13.587991] ath11k c000000.wifi: ipq8074 hw2.0
[ 13.588031] ath11k c000000.wifi: FW memory mode: 0
[ 13.591654] remoteproc remoteproc0: powering up cd00000.q6v5_wcss
[ 13.607720] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668
[ 14.154524] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 14.794498] remoteproc remoteproc0: remote processor cd00000.q6v5_wcss is now up
[ 14.798170] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 14.839944] ath11k c000000.wifi: qmi ignore invalid mem req type 3
[ 14.847390] ath11k c000000.wifi: chip_id 0x0 chip_family 0x0 board_id 0xff soc_id 0xffffffff
[ 14.847440] ath11k c000000.wifi: fw_version 0x290104a5 fw_build_timestamp 2023-08-02 20:32 fw_build_id WLAN.HK.2.9.0.1-01890-QCAHKSWPL_SILICONZ-1
[ 15.169603] ath11k c000000.wifi: htt event 48 not handled
[ 15.205086] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 16.234484] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 16.729050] br-lan: port 1(lan1) entered blocking state
[ 16.729093] br-lan: port 1(lan1) entered disabled state
[ 16.733307] device lan1 entered promiscuous mode
[ 16.744650] br-lan: port 2(lan2) entered blocking state
[ 16.744692] br-lan: port 2(lan2) entered disabled state
[ 16.748897] device lan2 entered promiscuous mode
[ 16.757653] br-lan: port 3(lan3) entered blocking state
[ 16.758762] br-lan: port 3(lan3) entered disabled state
[ 16.763918] device lan3 entered promiscuous mode
[ 16.772718] br-lan: port 4(lan4) entered blocking state
[ 16.773779] br-lan: port 4(lan4) entered disabled state
[ 16.779014] device lan4 entered promiscuous mode
[ 17.289197] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 18.314482] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 19.354460] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 19.914501] nss-dp 3a001600.dp4 lan4: PHY Link up speed: 1000
[ 19.914574] br-lan: port 4(lan4) entered blocking state
[ 19.919229] br-lan: port 4(lan4) entered forwarding state
[ 19.924568] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 20.394548] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 21.434443] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 22.474521] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 23.514503] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 24.554512] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 25.594505] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 26.634503] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 27.674512] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 28.714506] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 29.754516] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 30.794502] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 31.834527] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
Do you know how to prevent from displaying this error?
ssdk_phy_driver_init[371]:INFO:dev_id = 0, phy_adress = 5, phy_id = 0x6820805 phytype doesn't match
hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
There is not soldered Aquantia chip: https://www-acwifi-net.translate.goog/wp-content/uploads/2020/06/SAM_4473.jpg
I was trying add this to dts:
&mdio {
status = "okay";
.
.
.
aqr113c: ethernet-phy@5 {
compatible = "ethernet-phy-ieee802.3-c45";
reg = <8>;
};
};
.
.
.
&dp6_syn {
status = "disabled";
phy-handle = <&aqr113c>;
};
but didn't work.
partition2:
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00147
S - IMAGE_VARIANT_STRING=HAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e5
B - 201 - PBL, Start
B - 2734 - bootable_media_detect_entry, Start
B - 3440 - bootable_media_detect_success, Start
B - 3444 - elf_loader_entry, Start
B - 6105 - auth_hash_seg_entry, Start
B - 6348 - auth_hash_seg_exit, Start
B - 68411 - elf_segs_hash_verify_entry, Start
B - 131107 - PBL, End
B - 213378 - SBL1, Start
B - 291122 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B - 300821 - pm_device_init, Start
B - 478911 - PM_SET_VAL:Skip
D - 176076 - pm_device_init, Delta
B - 481168 - pm_driver_init, Start
D - 5307 - pm_driver_init, Delta
B - 487664 - clock_init, Start
D - 2104 - clock_init, Delta
B - 491690 - boot_flash_init, Start
D - 12688 - boot_flash_init, Delta
B - 508130 - boot_config_data_table_init, Start
D - 3141 - boot_config_data_table_init, Delta - (575 Bytes)
B - 515602 - Boot Setting : 0x00000618
B - 519598 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:8
B - 526430 - sbl1_ddr_set_params, Start
B - 530242 - CPR configuration: 0x30c
B - 533719 - cpr_init, Start
B - 536495 - Rail:0 Mode: 5 Voltage: 832000
B - 541680 - CL CPR settled at 784000mV
B - 544516 - Rail:1 Mode: 5 Voltage: 904000
B - 548695 - Rail:1 Mode: 7 Voltage: 944000
D - 16531 - cpr_init, Delta
B - 555588 - Pre_DDR_clock_init, Start
B - 559583 - Pre_DDR_clock_init, End
B - 562999 - DDR Type : PCDDR3
B - 568733 - do ddr sanity test, Start
D - 1067 - do ddr sanity test, Delta
B - 573491 - DDR: Start of HAL DDR Boot Training
B - 578127 - DDR: End of HAL DDR Boot Training
B - 583922 - DDR: Checksum to be stored on flash is 96661726
B - 594048 - Image Load, Start
D - 225853 - QSEE Image Loaded, Delta - (1373936 Bytes)
B - 819992 - Image Load, Start
D - 61 - SEC Image Loaded, Delta - (0 Bytes)
B - 827678 - Image Load, Start
D - 10736 - DEVCFG Image Loaded, Delta - (26004 Bytes)
B - 838506 - Image Load, Start
D - 25437 - RPM Image Loaded, Delta - (105964 Bytes)
B - 864004 - Image Load, Start
D - 102785 - APPSBL Image Loaded, Delta - (627152 Bytes)
B - 966911 - QSEE Execution, Start
D - 91 - QSEE Execution, Delta
B - 972706 - USB D+ check, Start
D - 0 - USB D+ check, Delta
B - 979111 - SBL1, End
D - 768020 - SBL1, Delta
S - Flash Throughput, 6679 KB/s (2134303 Bytes, 319510 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 1651 MHz
U-Boot 2016.01 (Mar 13 2020 - 17:34:10 +0800)
version: 0.3.14
DRAM: smem ram ptable found: ver: 1 len: 4
1 GiB
board_devinfo_offset=1060000, board_devinfo_size=20000
board_senv_offset=1040000, board_senv_size=20000
board_kernel_offset=0x1080000, board_fw_size=0x9600000, board_altkernel_offset=0xa680000\nNAND: ONFI device found
ID = 1590acad
Vendor = ad
Device = ac
qpic_nand: changing oobsize to 64 from 128 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
512 MiB
MMC: <NULL>: 0
devinfo_import--devinfo_mem_pool.crc=b107910
fun=cmd_init DEVINFO_ITEMS=511
devinfo: data is valid!
qpic_nand_read_oob: ecc failure while reading from 1040000
NAND read from offset 1040000 failed -74
read senv fail
*** Warning - readsenv() failed, using default senv
qpic_nand_read_oob: ecc failure while reading from 1040000
@@ nand_read error
#### auto_recovery enabled:1, boot_part:2, boot_part_ready:3, boot_count=0
####[boot_count_write] erase:0, auto_recovery->block_offset:0x1040000 offset=0x1058000
Updating boot_count ...
####[boot_count_write] offset:0x1058000 , length:2048
done
PCI Link Intialized
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010008
Card did not respond to voltage select!
eth0 MAC Address from ART is not valid
eth1 MAC Address from ART is not valid
eth2 MAC Address from ART is not valid
eth3 MAC Address from ART is not valid
eth4 MAC Address from ART is not valid
eth5 MAC Address from ART is not valid
auto_recovery_check changes bootcmd: boot from partition 2
Bus 0: i2c@78b6000
Setting bus to 0
Valid chip addresses: 62 68
Hit 'Space' or 'Enter' key to stop autoboot: 0
Normal boot
starting USB...
USB0: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 0 for devices... 1 USB Device(s) found
USB1: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 1 for devices... 1 USB Device(s) found
** Bad device usb 0 **
NAND read: device 0 offset 0x13e80000, size 0x80000
524288 bytes read: OK
Erasing NAND...
Erasing at 0x1020000 -- 100% complete.
Writing to NAND... OK
PHY::Scratchpad Read/Write test fail
Disable 50MHz clock...
Erasing NAND...
Erasing at 0x1020000 -- 100% complete.
Writing to NAND... OK
NAND read: device 0 offset 0xa680000, size 0x600000
6291456 bytes read: OK
## Loading kernel from FIT Image at 44000000 ...
Using 'config@1' configuration
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-6.1.62
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x440000e8
Data Size: 4876367 Bytes = 4.7 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x41000000
Entry Point: 0x41000000
Hash algo: crc32
Hash value: 24e8ed6e
Hash algo: sha1
Hash value: c67bf06552491008add72e8d576eb20586c637e3
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
Using 'config@1' configuration
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt linksys_mx5300 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x444a6a78
Data Size: 46062 Bytes = 45 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: 056c653d
Hash algo: sha1
Hash value: dae385754b516913f696c7432eaa8e652c23c58f
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x444a6a78
Uncompressing Kernel Image ... OK
Loading Device Tree to 4a3f1000, end 4a3ff3ed ... OK
Using machid 0x8010008 from environment
Starting kernel ...
Jumping to AARCH64 kernel via monitor
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 6.1.62 (a@a) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r24415-9062e5faae) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Sat Nov 18 11:23:54 2023
[ 0.000000] Machine model: Linksys MX5300
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000040ffffff]
[ 0.000000] node 0: [mem 0x0000000041000000-0x000000004a3fffff]
[ 0.000000] node 0: [mem 0x000000004a400000-0x00000000510fffff]
[ 0.000000] node 0: [mem 0x0000000051100000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] psci: OSI mode supported.
[ 0.000000] psci: failed to set PC mode: -1
[ 0.000000] percpu: Embedded 17 pages/cpu s31080 r8192 d30360 u69632
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048
[ 0.000000] Kernel command line: console=ttyMSM0,115200n8 ubi.mtd=alt_rootfs root=ubi0:ubifs rootfstype=ubifs rootwait swiotlb=1 root=/dev/ubiblock0_0 rootfstype=squashfs ro
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 887712K/1048576K available (7744K kernel code, 854K rwdata, 2268K rodata, 1280K init, 273K bss, 160864K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479]
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000001] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000109] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.000122] pid_max: default: 32768 minimum: 301
[ 0.000604] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.000617] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.002440] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.002449] cblist_init_generic: Setting shift to 2 and lim to 1.
[ 0.002641] rcu: Hierarchical SRCU implementation.
[ 0.002645] rcu: Max phase no-delay instances is 1000.
[ 0.003464] smp: Bringing up secondary CPUs ...
[ 0.004102] Detected VIPT I-cache on CPU1
[ 0.004248] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.004913] Detected VIPT I-cache on CPU2
[ 0.005017] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.005633] Detected VIPT I-cache on CPU3
[ 0.005732] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.005800] smp: Brought up 1 node, 4 CPUs
[ 0.005808] SMP: Total of 4 processors activated.
[ 0.005813] CPU features: detected: 32-bit EL0 Support
[ 0.005818] CPU features: detected: CRC32 instructions
[ 0.005880] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.005886] CPU: All CPU(s) started at EL1
[ 0.005889] alternatives: applying system-wide alternatives
[ 0.016890] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.016917] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.017133] pinctrl core: initialized pinctrl subsystem
[ 0.018272] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.018863] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.018908] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.018943] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.019372] thermal_sys: Registered thermal governor 'step_wise'
[ 0.019554] cpuidle: using governor menu
[ 0.019873] ASID allocator initialised with 65536 entries
[ 0.074401] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 0.082832] SCSI subsystem initialized
[ 0.083034] usbcore: registered new interface driver usbfs
[ 0.083086] usbcore: registered new interface driver hub
[ 0.083119] usbcore: registered new device driver usb
[ 0.083548] qcom_scm: convention: smc arm 64
[ 0.084876] clocksource: Switched to clocksource arch_sys_counter
[ 0.085996] NET: Registered PF_INET protocol family
[ 0.086140] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.087443] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.087467] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.087480] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.087568] TCP bind hash table entries: 8192 (order: 6, 262144 bytes, linear)
[ 0.087839] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.087939] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.087976] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.088204] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.088240] PCI: CLS 0 bytes, default 64
[ 0.089725] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[ 0.094827] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.094840] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.099184] qcom-qmp-usb-phy 78000.phy: supply vdda-phy not found, using dummy regulator
[ 0.099336] qcom-qmp-usb-phy 78000.phy: supply vdda-pll not found, using dummy regulator
[ 0.101048] qcom-qusb2-phy 79000.phy: supply vdd not found, using dummy regulator
[ 0.101199] qcom-qusb2-phy 79000.phy: supply vdda-pll not found, using dummy regulator
[ 0.101239] qcom-qusb2-phy 79000.phy: supply vdda-phy-dpdm not found, using dummy regulator
[ 0.101447] qcom-qusb2-phy 79000.phy: Registered Qcom-QUSB2 phy
[ 0.103535] qcom-pcie 10000000.pci: host bridge /soc/pci@10000000 ranges:
[ 0.103587] qcom-pcie 10000000.pci: IO 0x0010200000..0x001020ffff -> 0x0000000000
[ 0.103611] qcom-pcie 10000000.pci: MEM 0x0010220000..0x001fffffff -> 0x0010220000
[ 0.162842] qcom-pcie 10000000.pci: Read DBI address failed
[ 0.266476] qcom-pcie 10000000.pci: iATU unroll: disabled
[ 0.266485] qcom-pcie 10000000.pci: iATU regions: 32 ob, 8 ib, align 4K, limit 4G
[ 0.366579] qcom-pcie 10000000.pci: PCIe Gen.2 x1 link up
[ 0.366757] qcom-pcie 10000000.pci: PCI host bridge to bus 0001:00
[ 0.366769] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.366781] pci_bus 0001:00: root bus resource [io 0x0000-0xffff]
[ 0.366790] pci_bus 0001:00: root bus resource [mem 0x10220000-0x1fffffff]
[ 0.366828] pci 0001:00:00.0: [17cb:0302] type 01 class 0x060400
[ 0.366850] pci 0001:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff]
[ 0.366919] pci 0001:00:00.0: PME# supported from D0 D3hot D3cold
[ 0.370430] pci 0001:01:00.0: [168c:0046] type 00 class 0x028000
[ 0.370583] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.371341] pci 0001:01:00.0: supports D1
[ 0.371349] pci 0001:01:00.0: PME# supported from D0 D1 D3hot D3cold
[ 0.395054] pci 0001:00:00.0: BAR 8: assigned [mem 0x10400000-0x105fffff]
[ 0.395068] pci 0001:00:00.0: BAR 0: assigned [mem 0x10220000-0x10220fff]
[ 0.395083] pci 0001:01:00.0: BAR 0: assigned [mem 0x10400000-0x105fffff 64bit]
[ 0.395158] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[ 0.395169] pci 0001:00:00.0: bridge window [mem 0x10400000-0x105fffff]
[ 0.397415] pcieport 0001:00:00.0: PME: Signaling with IRQ 16
[ 0.397781] pcieport 0001:00:00.0: AER: enabled with IRQ 16
[ 0.401134] bam-dma-engine 704000.dma-controller: num-channels unspecified in dt
[ 0.401150] bam-dma-engine 704000.dma-controller: num-ees unspecified in dt
[ 0.405578] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.406190] msm_serial 78b3000.serial: msm_serial: detected port #0
[ 0.406241] msm_serial 78b3000.serial: uartclk = 3686400
[ 0.406333] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 21, base_baud = 230400) is a MSM
[ 0.406362] msm_serial: console setup on port #0
[ 1.231617] printk: console [ttyMSM0] enabled
[ 1.236776] msm_serial: driver initialized
[ 1.245738] loop: module loaded
[ 1.247189] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xac
[ 1.247695] nand: Hynix H27S4G8F2EDA-BC
[ 1.254285] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
[ 1.258244] 29 fixed-partitions partitions found on MTD device qcom_nand.0
[ 1.265526] Creating 29 MTD partitions on "qcom_nand.0":
[ 1.272435] 0x000000000000-0x000000100000 : "0:sbl1"
[ 1.279494] 0x000000100000-0x000000200000 : "0:mibib"
[ 1.284284] 0x000000200000-0x000000280000 : "0:bootconfig"
[ 1.288784] 0x000000280000-0x000000300000 : "0:bootconfig1"
[ 1.294145] 0x000000300000-0x000000600000 : "0:qsee"
[ 1.301986] 0x000000600000-0x000000900000 : "0:qsee_1"
[ 1.307222] 0x000000900000-0x000000980000 : "0:devcfg"
[ 1.309768] 0x000000980000-0x000000a00000 : "0:devcfg_1"
[ 1.314887] 0x000000a00000-0x000000a80000 : "0:apdp"
[ 1.320357] 0x000000a80000-0x000000b00000 : "0:apdp_1"
[ 1.325361] 0x000000b00000-0x000000b80000 : "0:rpm"
[ 1.330230] 0x000000b80000-0x000000c00000 : "0:rpm_1"
[ 1.335070] 0x000000c00000-0x000000c80000 : "0:cdt"
[ 1.340252] 0x000000c80000-0x000000d00000 : "0:cdt_1"
[ 1.344945] 0x000000d00000-0x000000d80000 : "0:appsblenv"
[ 1.350171] 0x000000d80000-0x000000e80000 : "0:appsbl"
[ 1.356040] 0x000000e80000-0x000000f80000 : "0:appsbl_1"
[ 1.361044] 0x000000f80000-0x000001000000 : "0:art"
[ 1.366090] 0x000001000000-0x000001040000 : "u_env"
[ 1.370379] 0x000001040000-0x000001060000 : "s_env"
[ 1.375167] 0x000001060000-0x000001080000 : "devinfo"
[ 1.380001] 0x000001080000-0x00000a680000 : "kernel"
[ 1.528121] 0x000001680000-0x00000a680000 : "rootfs"
[ 1.668108] mtd: setting mtd22 (rootfs) as root device
[ 1.668485] mtdsplit: no squashfs found in "rootfs"
[ 1.672154] 0x00000a680000-0x000013c80000 : "alt_kernel"
[ 1.820331] 0x00000ac80000-0x000013c80000 : "alt_rootfs"
[ 1.958271] 0x000013c80000-0x000013e80000 : "sysdiag"
[ 1.960681] 0x000013e80000-0x000013f00000 : "0:ethphyfw"
[ 1.963199] 0x000013f00000-0x00001f700000 : "syscfg"
[ 2.143738] 0x00001f700000-0x000020000000 : "0:wififw"
[ 2.162430] spmi spmi-0: PMIC arbiter version v2 (0x20010000)
[ 2.187074] i2c_dev: i2c /dev entries driver
[ 2.194032] sdhci: Secure Digital Host Controller Interface driver
[ 2.194076] sdhci: Copyright(c) Pierre Ossman
[ 2.199136] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.205249] remoteproc remoteproc0: releasing cd00000.q6v5_wcss
[ 2.211937] NET: Registered PF_INET6 protocol family
[ 2.215860] Segment Routing with IPv6
[ 2.220140] In-situ OAM (IOAM) with IPv6
[ 2.223738] NET: Registered PF_PACKET protocol family
[ 2.227742] 8021q: 802.1Q VLAN Support v1.8
[ 2.251907] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 2.252217] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
[ 2.258176] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1
[ 2.264632] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[ 2.272308] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[ 2.279823] cpr3_mem_acc_init: apc: not using memory accelerator regulator
[ 2.288947] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 704000 uV
[ 2.295896] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 832000 uV
[ 2.305885] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 896000 uV
[ 2.315687] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop=1000000 uV
[ 2.325550] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 679, quot_offset[ 7]= 0
[ 2.335308] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 906, quot_offset[ 7]= 225
[ 2.346158] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]=1006, quot_offset[ 7]= 100
[ 2.357094] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]=1175, quot_offset[ 7]= 165
[ 2.368225] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
[ 2.371116] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 800000 KHz, changing to: 1017600 KHz
[ 2.387454] remoteproc remoteproc0: cd00000.q6v5_wcss is available
[ 2.396868] ubi0: attaching mtd24
[ 2.674884] random: crng init done
[ 3.228073] ubi0: scanning is finished
[ 3.236160] ubi0: attached mtd24 (name "alt_rootfs", size 144 MiB)
[ 3.236201] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.241241] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.248123] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.254960] ubi0: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 3.261725] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 3.267983] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1700306634
[ 3.275104] ubi0: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 80
[ 3.284396] ubi0: background thread "ubi_bgt0d" started, PID 5�[ 3.302899] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 3.303310] Freeing unused kernel memory: 1280K
[ 3.374962] Run /sbin/init as init process
[ 3.522761] init: Console is alive
[ 3.522917] init: - watchdog -
[ 4.300793] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.383333] ssdk_dt_parse_interrupt[916]:INFO:intr-gpio does not exist
[ 4.447998] ssdk_phy_driver_init[371]:INFO:dev_id = 0, phy_adress = 5, phy_id = 0x6820805 phytype doesn't match
[ 4.448050] malibu_phy_api_ops_init[1934]:INFO:qca probe malibu phy driver succeeded!
[ 5.497141] regi_init[3603]:INFO:Initializing HPPE Done!!
[ 5.497263] regi_init[3662]:INFO:qca-ssdk module init succeeded!
[ 5.503629] EDMA ver 1 hw init
[ 5.507839] EDMA HW Reset completed succesfully
[ 5.510492] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7)
[ 5.514905] RxDesc:1 (15-15) RxFill:1 (7-7)
[ 5.524321] **********************************************************
[ 5.524357] * NSS Data Plane driver
[ 5.530884] **********************************************************
[ 5.608938] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 5.608988] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1
[ 5.613454] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000000002010010
[ 5.620939] xhci-hcd xhci-hcd.1.auto: irq 38, io mem 0x08a00000
[ 5.630345] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 5.636160] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2
[ 5.641713] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 5.649726] hub 1-0:1.0: USB hub found
[ 5.655883] hub 1-0:1.0: 1 port detected
[ 5.659949] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 5.663927] hub 2-0:1.0: USB hub found
[ 5.671802] hub 2-0:1.0: 1 port detected
[ 5.677876] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.680274] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 7.035431] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 8.091860] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 8.091992] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 794
[ 8.095532] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 8.174430] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 8.174476] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 8.181280] UBIFS (ubi0:1): FS size: 126722048 bytes (120 MiB, 998 LEBs), max 1009 LEBs, journal size 6348800 bytes (6 MiB, 50 LEBs)
[ 8.191167] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[ 8.203131] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 2100422F-A3F5-4D81-B487-1ABBD77F06AF, small LPT model
[ 8.213262] mount_root: switching to ubifs overlay
[ 8.224521] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[ 8.230874] urandom-seed: Seeding with /etc/urandom.seed
[ 8.281885] procd: - early -
[ 8.281979] procd: - watchdog -
[ 8.822486] procd: - watchdog -
[ 8.823011] procd: - ubus -
[ 8.979042] procd: - init -
Please press Enter to activate this console.
[ 9.115263] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 9.155892] kmodloader: loading kernel modules from /etc/modules.d/*
[ 9.192951] Loading modules backported from Linux version v6.5-0-g2dde18cd1d8f
[ 9.192991] Backport generated by backports.git v5.15.92-1-56-g5fb2ccb6b9e8
[ 9.203881] NET: Registered PF_QIPCRTR protocol family
[ 9.208276] rtc-ds1307 0-0068: registered as rtc0
[ 9.211408] rtc-ds1307 0-0068: setting system clock to 2023-11-19T13:57:53 UTC (1700402273)
[ 9.241226] PPP generic driver version 2.4.2
[ 9.241980] NET: Registered PF_PPPOX protocol family
[ 9.250959] ath10k 6.4 driver, optimized for CT firmware, probing pci device: 0x46.
[ 9.251367] ath10k_pci 0001:01:00.0: enabling device (0000 -> 0002)
[ 9.257961] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 9.330634] urngd: v1.0.2 started.
[ 9.848907] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 9.848958] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 9.858184] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 7ea63dc5
[ 10.155332] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 11.195320] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 12.153878] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id N/A crc32 56d3acd2
[ 12.235311] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 13.275311] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 13.354514] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 13.354561] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[ 13.437651] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 13.438452] ath10k_pci 0001:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224'
[ 13.727186] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal nvmem max-sta 32 raw 0 hwcrypto 1
[ 13.818807] ath11k c000000.wifi: ipq8074 hw2.0
[ 13.818844] ath11k c000000.wifi: FW memory mode: 0
[ 13.822628] remoteproc remoteproc0: powering up cd00000.q6v5_wcss
[ 13.838608] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668
[ 14.315302] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 15.047454] remoteproc remoteproc0: remote processor cd00000.q6v5_wcss is now up
[ 15.050948] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 15.091497] ath11k c000000.wifi: qmi ignore invalid mem req type 3
[ 15.098992] ath11k c000000.wifi: chip_id 0x0 chip_family 0x0 board_id 0xff soc_id 0xffffffff
[ 15.099039] ath11k c000000.wifi: fw_version 0x290104a5 fw_build_timestamp 2023-08-02 20:32 fw_build_id WLAN.HK.2.9.0.1-01890-QCAHKSWPL_SILICONZ-1
[ 15.355273] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 15.423873] ath11k c000000.wifi: htt event 48 not handled
[ 16.395329] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 17.045392] br-lan: port 1(lan1) entered blocking state
[ 17.045439] br-lan: port 1(lan1) entered disabled state
[ 17.049650] device lan1 entered promiscuous mode
[ 17.063179] br-lan: port 2(lan2) entered blocking state
[ 17.063221] br-lan: port 2(lan2) entered disabled state
[ 17.067489] device lan2 entered promiscuous mode
[ 17.075955] br-lan: port 3(lan3) entered blocking state
[ 17.077289] br-lan: port 3(lan3) entered disabled state
[ 17.082441] device lan3 entered promiscuous mode
[ 17.090750] br-lan: port 4(lan4) entered blocking state
[ 17.092309] br-lan: port 4(lan4) entered disabled state
[ 17.097502] device lan4 entered promiscuous mode
[ 17.449553] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 18.475288] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 19.515274] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 20.235310] nss-dp 3a001600.dp4 lan4: PHY Link up speed: 1000
[ 20.235383] br-lan: port 4(lan4) entered blocking state
[ 20.240037] br-lan: port 4(lan4) entered forwarding state
[ 20.245358] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 20.555358] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 21.595341] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 22.635332] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 23.675310] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 24.715307] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 25.755314] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 26.795306] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 27.835324] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
[ 28.875313] hsl_phy_phydev_get[805]:ERROR:phy_addr 5 phydev is NULL
For BT chip (QCA4024) support over spi this patch need to be applied:
--- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
@@ -572,6 +572,13 @@
bias-disable;
};
+ spi_3_pins: spi-3-state {
+ pins = "gpio50", "gpio52", "gpio53";
+ function = "blsp3_spi";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
hsuart_pins: hsuart-state {
pins = "gpio46", "gpio47", "gpio48", "gpio49";
function = "blsp2_uart";
@@ -750,6 +757,23 @@
status = "disabled";
};
+ blsp1_spi4: spi@78b8000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x078b8000 0x600>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ spi-max-frequency = <50000000>;
+ clocks = <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 18>, <&blsp_dma 19>;
+ dma-names = "tx", "rx";
+ pinctrl-0 = <&spi_3_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
blsp1_i2c5: i2c@78b9000 {
compatible = "qcom,i2c-qup-v2.2.1";
#address-cells = <1>;
Can it be submitted?
What do you think about new option for sysupgrade?
-s stay on current partition (dual boot)
I have implemented passing flag by system env:
-s) fw_setenv sysupgrade_stay_cur_part 1;;
And reading them in platform.sh.
I can upstream the missing SPI node, that is not an issue.
But, why do you need this new sysupgrade option?
You can control everything from the stage2 calls being made in platform.sh
I just want to be able to do upgrade on currently booted partition.
Here is my logic:
CI_UBIPART="rootfs"
boot_part="$(fw_printenv -n boot_part)"
sysupgrade_stay_cur_part="$(fw_printenv -n sysupgrade_stay_cur_part)"
if [ "$sysupgrade_stay_cur_part" -eq "1" ]; then
if [ "$boot_part" -eq "2" ]; then
CI_KERNPART="alt_kernel"
CI_UBIPART="alt_rootfs"
fi
else
if [ "$boot_part" -eq "1" ]; then
fw_setenv boot_part 2
CI_KERNPART="alt_kernel"
CI_UBIPART="alt_rootfs"
else
fw_setenv boot_part 1
fi
fi
fw_setenv boot_part_ready 3
fw_setenv auto_recovery yes
nand_do_upgrade "$1"
;;
@robimarko @Ansuel I'm trying to prepare BDF files for this router. There are many BDF's in the OEM firmware but they are all country locked.
Using e.g. US (FCC) BDF for IPQ8074 we are not able to change country:
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.548468] CPU: 0 PID: 3212 Comm: kworker/0:1 Not tainted 6.1.64 #0
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.570703] Hardware name: Linksys MX5300 (DT)
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.577301] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.581553] pc : ath11k_wmi_tlv_parse_alloc+0x834/0x3140 [ath11k]
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.588410] lr : ath11k_wmi_tlv_parse_alloc+0x834/0x3140 [ath11k]
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.594659] sp : ffffffc008003c00
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.600731] x29: ffffffc008003c00 x28: 0000000000000044 x27: 0000000000000000
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.604036] x26: 000000000000004c x25: 000000000000019d x24: ffffff8006781540
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.611154] x23: 0000000000000000 x22: ffffff8004fa0000 x21: 0000000000000000
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.618272] x20: ffffff8003c24000 x19: ffffff8011446000 x18: 0000000000000160
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.625390] x17: 65636572206d6f72 x16: 66206f666e692079 x15: ffffffc008b37240
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.632509] x14: 0000000000000420 x13: 0000000000000160 x12: 00000000ffffffea
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.639627] x11: 00000000ffffefff x10: ffffffc008b8f240 x9 : ffffffc008b371e8
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.646744] x8 : 0000000000017fe8 x7 : c0000000ffffefff x6 : 0000000000000001
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.653863] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.660981] x2 : 0000000000000000 x1 : ffffff80031c0c00 x0 : 000000000000004a
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.668099] Call trace:
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.675208] ath11k_wmi_tlv_parse_alloc+0x834/0x3140 [ath11k]
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.677472] ath11k_wmi_tlv_parse_alloc+0x1b98/0x3140 [ath11k]
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.683374] ath11k_htc_rx_completion_handler+0x418/0x600 [ath11k]
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.689104] ath11k_ce_per_engine_service+0x2a8/0x3b0 [ath11k]
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.695267] 0xffffffc000b6fb84
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.701076] tasklet_action_common.constprop.0+0x144/0x180
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.704120] tasklet_action+0x28/0x34
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.709672] _stext+0x10c/0x278
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.713402] ____do_softirq+0x10/0x20
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.716356] call_on_irq_stack+0x24/0x50
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.720176] do_softirq_own_stack+0x1c/0x30
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.724170] __irq_exit_rcu+0xac/0xe0
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.728074] irq_exit_rcu+0x10/0x1c
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.731893] el1_interrupt+0x38/0x5c
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.735193] el1h_64_irq_handler+0x18/0x2c
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.739013] el1h_64_irq+0x68/0x6c
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.742918] format_decode+0x10/0x594
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.746304] vsnprintf+0x124/0x704
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.750036] __kthread_create_on_node+0x118/0x1f0
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.753337] kthread_create_on_node+0x44/0x50
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.758111] create_worker+0xc4/0x1f4
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.762449] worker_thread+0x3a4/0x4b4
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.766096] kthread+0xd8/0xe4
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.769741] ret_from_fork+0x10/0x20
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.772780] ---[ end trace 0000000000000000 ]---
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.778236] ath11k c000000.wifi: No regulatory rules available in the event info
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.781123] ath11k c000000.wifi: failed to extract regulatory info from received event
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.788537] ------------[ cut here ]------------
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.796219] WARNING: CPU: 0 PID: 0 at ath11k_wmi_tlv_parse_alloc+0x834/0x3140 [ath11k]
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.801000] Modules linked in: pppoe ppp_async nft_fib_inet nf_flow_table_inet ath11k_ahb ath11k ath10k_pci ath10k_core ath pppox ppp_generic nft_reject_ipv6 nft_reject_ipv4 nft_reject_inet nft_reject nft_redir nft_quota nft_objref nft_numgen nft_nat nft_masq nft_log nft_limit nft_hash nft_flow_offload nft_fib_ipv6 nft_fib_ipv4 nft_fib nft_ct nft_chain_nat nf_tables nf_nat nf_flow_table nf_conntrack mac80211 cfg80211 spidev slhc rtc_ds1307 regmap_i2c qrtr_smd qrtr qmi_helpers nfnetlink nf_reject_ipv6 nf_reject_ipv4 nf_log_syslog nf_defrag_ipv6 nf_defrag_ipv4 libcrc32c compat sha512_generic seqiv jitterentropy_rng drbg michael_mic hmac cmac leds_pca963x leds_gpio xhci_plat_hcd xhci_pci xhci_hcd dwc3 dwc3_qcom qca_nss_dp qca_ssdk gpio_button_hotplug ext4 mbcache jbd2 aquantia hwmon crc_ccitt crc32c_generic
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.857581] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 6.1.64 #0
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.879818] Hardware name: Linksys MX5300 (DT)
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.887452] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.891709] pc : ath11k_wmi_tlv_parse_alloc+0x834/0x3140 [ath11k]
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.898566] lr : ath11k_wmi_tlv_parse_alloc+0x834/0x3140 [ath11k]
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.904816] sp : ffffffc008003c00
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.910886] x29: ffffffc008003c00 x28: 0000000000000044 x27: 0000000000000000
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.914192] x26: 0000000000000018 x25: 00000000000001a0 x24: ffffff80129c76c0
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.921311] x23: 0000000000000000 x22: ffffff8004fa0000 x21: 0000000000000000
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.928428] x20: ffffff8003c24000 x19: ffffff8011446000 x18: 000000000000018f
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.935547] x17: 65636572206d6f72 x16: 66206f666e692079 x15: ffffffc008b37240
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.942665] x14: 00000000000004ad x13: 000000000000018f x12: 00000000ffffffea
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.949783] x11: 00000000ffffefff x10: ffffffc008b8f240 x9 : ffffffc008b371e8
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.956901] x8 : 0000000000017fe8 x7 : c0000000ffffefff x6 : 0000000000000001
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.964020] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.971137] x2 : 0000000000000000 x1 : ffffffc008b2e140 x0 : 000000000000004a
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.978256] Call trace:
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.985364] ath11k_wmi_tlv_parse_alloc+0x834/0x3140 [ath11k]
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.987627] ath11k_wmi_tlv_parse_alloc+0x1b98/0x3140 [ath11k]
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.993530] ath11k_htc_rx_completion_handler+0x418/0x600 [ath11k]
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 450.999261] ath11k_ce_per_engine_service+0x2a8/0x3b0 [ath11k]
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.005423] 0xffffffc000b6fb84
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.011233] tasklet_action_common.constprop.0+0x144/0x180
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.014276] tasklet_action+0x28/0x34
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.019829] _stext+0x10c/0x278
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.023559] ____do_softirq+0x10/0x20
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.026512] call_on_irq_stack+0x24/0x50
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.030331] do_softirq_own_stack+0x1c/0x30
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.034325] __irq_exit_rcu+0xac/0xe0
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.038231] irq_exit_rcu+0x10/0x1c
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.042050] el1_interrupt+0x38/0x5c
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.045349] el1h_64_irq_handler+0x18/0x2c
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.049168] el1h_64_irq+0x68/0x6c
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.053074] arch_cpu_idle+0x18/0x2c
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.056461] default_idle_call+0x30/0x74
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.060193] do_idle+0x228/0x250
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.064098] cpu_startup_entry+0x38/0x40
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.067311] kernel_init+0x0/0x130
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.071216] arch_post_acpi_subsys_init+0x0/0x18
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.074432] start_kernel+0x674/0x698
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.079204] __primary_switched+0xb4/0xbc
Mon Dec 4 00:46:45 2023 kern.warn kernel: [ 451.082763] ---[ end trace 0000000000000000 ]---
Mon Dec 4 00:46:45 2023 kern.info kernel: [ 451.087814] br-lan: port 6(phy1-ap0) entered blocking state
Mon Dec 4 00:46:46 2023 kern.info kernel: [ 451.091450] br-lan: port 6(phy1-ap0) entered disabled state
Mon Dec 4 00:46:46 2023 kern.info kernel: [ 451.097012] device phy1-ap0 entered promiscuous mode
Mon Dec 4 00:46:46 2023 kern.info kernel: [ 451.102380] br-lan: port 6(phy1-ap0) entered blocking state
Mon Dec 4 00:46:46 2023 kern.info kernel: [ 451.107527] br-lan: port 6(phy1-ap0) entered forwarding state
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.113561] ath11k c000000.wifi: No regulatory rules available in the event info
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.118750] ath11k c000000.wifi: failed to extract regulatory info from received event
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.126226] ------------[ cut here ]------------
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.133895] WARNING: CPU: 0 PID: 1804 at ath11k_wmi_tlv_parse_alloc+0x834/0x3140 [ath11k]
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.138675] Modules linked in: pppoe ppp_async nft_fib_inet nf_flow_table_inet ath11k_ahb ath11k ath10k_pci ath10k_core ath pppox ppp_generic nft_reject_ipv6 nft_reject_ipv4 nft_reject_inet nft_reject nft_redir nft_quota nft_objref nft_numgen nft_nat nft_masq nft_log nft_limit nft_hash nft_flow_offload nft_fib_ipv6 nft_fib_ipv4 nft_fib nft_ct nft_chain_nat nf_tables nf_nat nf_flow_table nf_conntrack mac80211 cfg80211 spidev slhc rtc_ds1307 regmap_i2c qrtr_smd qrtr qmi_helpers nfnetlink nf_reject_ipv6 nf_reject_ipv4 nf_log_syslog nf_defrag_ipv6 nf_defrag_ipv4 libcrc32c compat sha512_generic seqiv jitterentropy_rng drbg michael_mic hmac cmac leds_pca963x leds_gpio xhci_plat_hcd xhci_pci xhci_hcd dwc3 dwc3_qcom qca_nss_dp qca_ssdk gpio_button_hotplug ext4 mbcache jbd2 aquantia hwmon crc_ccitt crc32c_generic
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.195515] CPU: 0 PID: 1804 Comm: netifd Tainted: G W 6.1.64 #0
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.217754] Hardware name: Linksys MX5300 (DT)
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.225386] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.229644] pc : ath11k_wmi_tlv_parse_alloc+0x834/0x3140 [ath11k]
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.236499] lr : ath11k_wmi_tlv_parse_alloc+0x834/0x3140 [ath11k]
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.242750] sp : ffffffc008003c00
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.248820] x29: ffffffc008003c00 x28: 0000000000000044 x27: 0000000000000000
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.252127] x26: 000000000000004c x25: 00000000000001a5 x24: ffffff8013ff3240
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.259245] x23: 0000000000000000 x22: ffffff8004fa0000 x21: 0000000000000000
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.266363] x20: ffffff8003c24000 x19: ffffff8011446000 x18: 00000000000001c3
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.273482] x17: 65636572206d6f72 x16: 66206f666e692079 x15: ffffffc008b37240
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.280598] x14: 0000000000000549 x13: 00000000000001c3 x12: 00000000ffffffea
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.287717] x11: 00000000ffffefff x10: ffffffc008b8f240 x9 : ffffffc008b371e8
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.294835] x8 : 0000000000017fe8 x7 : c0000000ffffefff x6 : 0000000000000001
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.301953] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.309072] x2 : 0000000000000000 x1 : ffffff8002a80c00 x0 : 000000000000004a
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.316189] Call trace:
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.323299] ath11k_wmi_tlv_parse_alloc+0x834/0x3140 [ath11k]
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.325562] ath11k_wmi_tlv_parse_alloc+0x1b98/0x3140 [ath11k]
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.331464] ath11k_htc_rx_completion_handler+0x418/0x600 [ath11k]
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.337194] ath11k_ce_per_engine_service+0x2a8/0x3b0 [ath11k]
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.343357] 0xffffffc000b6fb84
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.349167] tasklet_action_common.constprop.0+0x144/0x180
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.352210] tasklet_action+0x28/0x34
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.357763] _stext+0x10c/0x278
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.361493] ____do_softirq+0x10/0x20
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.364446] call_on_irq_stack+0x24/0x50
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.368267] do_softirq_own_stack+0x1c/0x30
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.372260] __irq_exit_rcu+0xac/0xe0
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.376165] irq_exit_rcu+0x10/0x1c
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.379983] el1_interrupt+0x38/0x5c
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.383283] el1h_64_irq_handler+0x18/0x2c
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.387103] el1h_64_irq+0x68/0x6c
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.391007] __wake_up_common_lock+0xb0/0x110
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.394396] __wake_up_sync_key+0x20/0x30
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.398822] sock_def_readable+0x3c/0x80
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.402815] __netlink_sendskb+0x58/0x7c
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.406807] netlink_broadcast+0x338/0x41c
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.410715] nlmsg_notify+0x54/0x150
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.414619] rtnl_notify+0x30/0x3c
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.418352] br_info_notify+0xac/0x130
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.421564] br_ifinfo_notify+0x14/0x20
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.425296] brport_store+0x1dc/0x220
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.429029] sysfs_kf_write+0x44/0x54
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.432849] kernfs_fop_write_iter+0x118/0x1e0
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.436497] vfs_write+0x1a4/0x340
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.440834] ksys_write+0x5c/0xe0
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.444221] __arm64_sys_write+0x1c/0x30
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.447606] invoke_syscall.constprop.0+0x5c/0x104
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.451602] do_el0_svc+0x58/0x17c
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.456199] el0_svc+0x18/0x54
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.459583] el0t_64_sync_handler+0xf4/0x120
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.462625] el0t_64_sync+0x174/0x178
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.467051] ---[ end trace 0000000000000000 ]---
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.470653] ath11k c000000.wifi: No regulatory rules available in the event info
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.475312] ath11k c000000.wifi: failed to extract regulatory info from received event
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.482704] ------------[ cut here ]------------
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.490403] WARNING: CPU: 0 PID: 1804 at ath11k_wmi_tlv_parse_alloc+0x834/0x3140 [ath11k]
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.495184] Modules linked in: pppoe ppp_async nft_fib_inet nf_flow_table_inet ath11k_ahb ath11k ath10k_pci ath10k_core ath pppox ppp_generic nft_reject_ipv6 nft_reject_ipv4 nft_reject_inet nft_reject nft_redir nft_quota nft_objref nft_numgen nft_nat nft_masq nft_log nft_limit nft_hash nft_flow_offload nft_fib_ipv6 nft_fib_ipv4 nft_fib nft_ct nft_chain_nat nf_tables nf_nat nf_flow_table nf_conntrack mac80211 cfg80211 spidev slhc rtc_ds1307 regmap_i2c qrtr_smd qrtr qmi_helpers nfnetlink nf_reject_ipv6 nf_reject_ipv4 nf_log_syslog nf_defrag_ipv6 nf_defrag_ipv4 libcrc32c compat sha512_generic seqiv jitterentropy_rng drbg michael_mic hmac cmac leds_pca963x leds_gpio xhci_plat_hcd xhci_pci xhci_hcd dwc3 dwc3_qcom qca_nss_dp qca_ssdk gpio_button_hotplug ext4 mbcache jbd2 aquantia hwmon crc_ccitt crc32c_generic
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.552024] CPU: 0 PID: 1804 Comm: netifd Tainted: G W 6.1.64 #0
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.574264] Hardware name: Linksys MX5300 (DT)
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.581896] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.586153] pc : ath11k_wmi_tlv_parse_alloc+0x834/0x3140 [ath11k]
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.593009] lr : ath11k_wmi_tlv_parse_alloc+0x834/0x3140 [ath11k]
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.599261] sp : ffffffc008003c00
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.605330] x29: ffffffc008003c00 x28: 0000000000000044 x27: 0000000000000000
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.608638] x26: 000000000000004c x25: 00000000000001a5 x24: ffffff8013ff1ec0
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.615755] x23: 0000000000000000 x22: ffffff8004fa0000 x21: 0000000000000000
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.622873] x20: ffffff8003c24000 x19: ffffff8011446000 x18: 00000000000001fe
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.629991] x17: 65636572206d6f72 x16: 66206f666e692079 x15: ffffffc008b37240
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.637109] x14: 00000000000005fa x13: 00000000000001fe x12: 00000000ffffffea
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.644227] x11: 00000000ffffefff x10: ffffffc008b8f240 x9 : ffffffc008b371e8
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.651346] x8 : 0000000000017fe8 x7 : c0000000ffffefff x6 : 0000000000000001
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.658464] x5 : ffffff803fda1708 x4 : 0000000000000000 x3 : 0000000000000000
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.665581] x2 : 0000000000000000 x1 : ffffff8002a80c00 x0 : 000000000000004a
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.672700] Call trace:
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.679807] ath11k_wmi_tlv_parse_alloc+0x834/0x3140 [ath11k]
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.682072] ath11k_wmi_tlv_parse_alloc+0x1b98/0x3140 [ath11k]
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.687975] ath11k_htc_rx_completion_handler+0x418/0x600 [ath11k]
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.693704] ath11k_ce_per_engine_service+0x2a8/0x3b0 [ath11k]
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.699866] 0xffffffc000b6fb84
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.705677] tasklet_action_common.constprop.0+0x144/0x180
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.708721] tasklet_action+0x28/0x34
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.714273] _stext+0x10c/0x278
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.718003] ____do_softirq+0x10/0x20
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.720956] call_on_irq_stack+0x24/0x50
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.724777] do_softirq_own_stack+0x1c/0x30
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.728770] __irq_exit_rcu+0xac/0xe0
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.732675] irq_exit_rcu+0x10/0x1c
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.736494] el1_interrupt+0x38/0x5c
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.739794] el1h_64_irq_handler+0x18/0x2c
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.743613] el1h_64_irq+0x68/0x6c
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.747518] __wake_up_common_lock+0xb0/0x110
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.750906] __wake_up_sync_key+0x20/0x30
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.755332] sock_def_readable+0x3c/0x80
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.759326] __netlink_sendskb+0x58/0x7c
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.763318] netlink_broadcast+0x338/0x41c
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.767224] nlmsg_notify+0x54/0x150
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.771130] rtnl_notify+0x30/0x3c
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.774862] br_info_notify+0xac/0x130
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.778074] br_ifinfo_notify+0x14/0x20
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.781808] brport_store+0x1dc/0x220
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.785540] sysfs_kf_write+0x44/0x54
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.789359] kernfs_fop_write_iter+0x118/0x1e0
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.793007] vfs_write+0x1a4/0x340
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.797344] ksys_write+0x5c/0xe0
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.800730] __arm64_sys_write+0x1c/0x30
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.804117] invoke_syscall.constprop.0+0x5c/0x104
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.808111] do_el0_svc+0x58/0x17c
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.812709] el0_svc+0x18/0x54
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.816095] el0t_64_sync_handler+0xf4/0x120
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.819135] el0t_64_sync+0x174/0x178
Mon Dec 4 00:46:46 2023 kern.warn kernel: [ 451.823561] ---[ end trace 0000000000000000 ]---
I have found that the regulatory domain code is in the 4 different places:
It can be edited and set to 0x0000. After that change we are able to change country.
I don't know how to do the same change in the case of QCA9984. Regulatory domain code is only in one place but there is also some kind of checksum:
More about regulatory domain codes can be found here: https://fcc.report/FCC-ID/B94HHI31C/1616417.pdf
BDF's for US, EU and CA have second variant used in case if CN country is selected (script for selecting BDF: Adding OpenWrt support for Linksys MX5300 - #11 by lytr). I'm not sure what is the difference:
- IPQ8074
- QCA9984
Test build if anyone would like to try:
Flash instructions:
I'll give it a try somewhere next week.
Not going to happen this week, I'm on a holiday.
How are things working on the MX5300? I see that the pull request merged back in Feb.
The wiki page for it is still the template though. Most of the info to fill it in is available. Unfortunately, I don't have an Openwrt wiki account.
For anyone desiring to get the MX5300, the two pack refurb MX10600, is $130 at Woot currently. That's a pretty good price to get a 4x4 AX 2.4 GHz and 5 GHz radios plus a bonux 4x4 5GHz ac radio. Since Linksys seems to have stopped updating the oem firmware back in 2022, the responsible thing would be to run OpenWRT on it.
I'm thinking of getting one. The oem firmware requires an app to setup. Can I load OpenWRT without ever setting up their app?
For installation instructions, check the commit message: https://github.com/openwrt/openwrt/commit/70fd815e57dc98cef88828faa5ce71717540e99e
And here is Linksys instructions on how to manually install the firmware: https://www.linksys.com/support-article?articleNum=47547
You can install OpenWrt without any prior configuration.
1 Like
is anyonw willing to share a new link for the image download, im not able to find any build, installation instructions link is not working...